Cold Circular Saw

KALTENBACH SKL 370

Condition: used, saw blade diameter 370 mm cutting range round 115 mm cutting range square 105 mm cutting range flat 70 x 240 mm cutting length min. 730 mm cutting lenght max. 4000 mm saw blade turning speeds 1250 / 2500 U/min table rotating 180 ° stroke 120 mm feed stepless 0 - 500 mm/min coolant capacity 45 degrees: square 95 mm capacity 45 degrees: flat 50 x 200 mm cutting speed 1250 / 2500 m/min weight of the machine ca. 1,1 t dimensions of the machine ca. 5,00 x 1,30 x 2,00 m Mulv80 Double Mitre Saw for aluminium consits of two SKL 370 Circular Saws on common rails, one saw fixed one saw movable. - Serial No.: 28232 / 28233 - pneunatic clamping of workpiece - coolant equipment

Condition: used, diameter of saw band: 350cutting area - round: 350cutting area rectangle: 350 x 350total power requirements: 2,2 Drg0Ub Used cold circular saw Kaltenbach SKL 350 Saw Blade Diameter: 355 mm Speeds: 1420/2880 rpm Drive: 3.7/4.5 kW Includes: Coolant system Dimensions: 990/1140/H1535 mm Weight: 596 kg

Condition: ready for operation (used), Saw blade diameter: 450mm, cutting width: 4mm, saw blade type: HM/HSS, mounting hole: 50mm, fastening screws: 4, pitch circle fastening screws: 80mm, screw diameter: M12. Saw blade feed speed: 3.5m/min, rapid return: 4.5m/min, feed speed: 10m/min/20m/min, cut-off length single stroke: 10mm/1000mm, double stroke: 2000mm, turntable tilt: +/-90°. Machine dimensions X/Y/Z: approx. 2700mm/1450mm/1900mm, weight: approx. 1500kg. Documentation available. On-site inspection is possible. Dre7Qn

Condition: good (used), saw blade diameter: 400 mm, - Double miter - Mist lubrication system - protective cap - 400V 2Bz8Vizf

Condition: used, Year of construction: 1975, saw blade diameter 400 mm cutting diameter 130 mm stroke 135 mm saw blade diameter 370/400 mm feed speeds 0-500 mm/min Dqyvlv cutting speed 1400/2800 U/min range of angles 0-180 ° capacity 90 degrees: square 120 x 120 mm capacity 90 degrees: flat 280 x 70 mm capacity 45 degrees: square 105 mm Wheel width 185 mm Required air-pressure 8 bar total power requirement 3,7/4,5 kW weight of the machine ca. 650 kg dimensions of the machine ca. 1,3 x 1,1 x 1,7 m Robust semi-automatic light metal profile sawing machine with cut from below and pneum. workpiece clamping from above, saw bridge adjustable from front to back. The year of construction is estimated! Any additional required safety shielding must be installed by the purchaser. Machine dealer with own stock of 1600 m².

Condition: good (used), Year of construction: 1984, machine/vehicle number: 102335, Offer 23172 Bpjbjtvzw Technical data: - Saw blade diameter up to 400 mm - Cutting range with saw blade diameter 400 mm - at 90° round 130 mm - square 120 mm - flat up to 260 x 60 mm - Mitre adjustment left + right 0 - 90 ° - Cutting speed 1750 / 3500 m/min - Feed speed of the saw blade 0 - 3 m/min - Rapid return 3000 mm/min - Saw drive 400 V / 3.7 / 4.4 kW - Pneum. Material vice with adjustable clamping pressure - Space requirement approx. W 1200 x H 1900 x D 1200 mm - Weight approx. 600 kg - Outfeed roller conveyor 3000 mm - Infeed roller conveyor 3000 mm

Year of construction: 1971, Condition: used, machine/vehicle number: 23964, disk of circular saw-Ø: 370 mm cutting area at 90°: 115 mm Psn3Bq cutting area at 45°: 115 mm engine: 380 V, 4/5 kW space needed: 1000 x 1200/2200 x 1500 mm weight: ca. 900 kg

Condition: good (used), Year of construction: 1968, Saw blade diameter 370 mm Cutting capacity 45° - 90 round 115 mm flat approx. 215 x 20 mm rectangular approx. 95 x 105 mm U-profile approx. 160 x 55 mm Cutting speed 30, 60, 130 and 260 m/min Motor power approx. 2.6 kW Dimensions L x W x H 1100 x 1050 x 1600 mm Weight 850 kg Accessories / Special features: - Semi-automatic operation - After starting, the workpiece is automatically clamped with the upper clamping cylinder. Once the set feed end has been reached, the saw blade moves down automatically and the clamping vice is released again. - Hydro-pneumatic stepless saw blade feed Blovhukmpmn - Mitre cut on both sides R - L - 0° longitudinal cut possible - Coolant system - 1 saw blade Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: good (used), Year of construction: 1997, Semi automatic Aluminium circular saw, blade Ø 350 mm, capacity Ø ca. 125 mm, motor 3,7 / 4,5 kw 2-speed 1420/2880 rpm, vertical clamp, stops 30°, 45°, 60° 90° double side, blade; dimension 100x115x155 cm, ca. 600 kgs 2Au8Uvru

Condition: ready for operation (used), Kaltenbach SKL light metal circular saw 380 Volt Bv27Uyzi saw blade diameter 350mm mitre left+right 30 fence adjustable

Year of construction: 1980, Condition: used, saw blade diameter 380 mm pneumatic clamping ja Ewa2Kwx weight of the machine ca. 1,3 t

Year of construction: 1986, Condition: good (used), machine/vehicle number: 106157, Offer 21035 Technical data: Dye9Ve - Saw blade diameter up to 400 mm - Cutting range with saw blade diameter 400 mm - at 90° round 130 mm - square 120 mm - flat up to 260 x 60 mm - mitre adjustment left + right 0 - 90 ° - cutting speed 1750 / 3500 m/min - feed speed of the saw blade 0 - 3 m/min - rapid return 3000 mm/min - Saw drive 400 V / 3,7 / 4,4 kW - 2 pieces pneum. Material clamping vices with adjustable clamping pressure - space requirement approx. W 1200 x H 1900 x D 1200 mm - weight approx. 600 kg

Condition: good (used), saw blade diameter: 370 mm, 1 branded cold circular saw make: KALTENBACH , type: KKS 370 Swivel +/- 90°, with hydraulic clamping and roller conveyor with adjustable longitudinal stop Dimensions: , width 1000 mm, depth 1000 mm, height 1600 mm Weight: approx. 850 kg The machine works. You are welcome to view and test the machine in our warehouse under power to see for yourself The sale takes place as usual with used machines without guarantees according to our AGB's Payment: Cash on collection or bank transfer in advance Mymw9Cpb Free professional loading onto your transport vehicle is a matter of course. Optional: Insured forwarding shipment against payment of costs.

Condition: good (used), Year of construction: 1973, Saw blade diameter 370 mm Cutting capacity 45° - 90 round 115 mm flat approx. 215 x 20 mm rectangular approx. 95 x 105 mm U-profile approx. 160 x 55 mm Cutting speeds 11 - 15 - 22 m/min Motor power 0.9 - 1.2 - 1.4 kW Dimensions L x W x H 1100 x 1050 x 1600 mm Weight 850 kg Accessories / Special features: Pbfl8Fsmmb - Semi-automatic operation - After starting, the workpiece is automatically clamped with the upper clamping cylinder. Once the set feed end has been reached, the saw blade moves down automatically and the clamping vice is released again. - Fully hydraulic stepless saw blade feed - 3-way pole-changing saw motor - Mitre cut R - L on both sides - 0° longitudinal cut possible - Coolant system - 1 saw blade Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: used, Max. saw blade diameter: 370 mm Beiz0Z3

Condition: good (used), Automatic Circular Saw KALTENBACH Ø 370 mm Blades diameter: Ø 370 mm Maxi cutting height in round: 115 mm Maxi cutting height in flat: 120 mm 2 speed rotation motor Utrt870Gx7 Graduated circular tray Ø 590 mm Swivel +/- 45° Hydraulic clamping of the workpiece Graduated stop length: 2000 mm Machine used only for stainless steel cutting Voltage: 380 V Length with fixed feed: 3000 mm Depth: 1400 mm Height: 2000 mm Weight: approx 900 kg

Condition: used, saw blade diameter 400 mm cutting diameter 135 mm capacity 90 degrees: flat 280 x 70 mm Dpekbb capacity 90 degrees: square 120 x 120 mm capacity 45 degrees: flat 210 x 55 mm capacity 45 degrees: square 105 x 105 mm turning speeds max. 3000 U/min saw-blade dia. 400 x 3,2 x 40 mm motor 400 Volt total power requirement 4,0 kW weight 650 kg range L-W-H 910 x 1200 x 1700 mm Furnishing: - Miter circular saw for light metal & plastic profiles - Precise and accident-free work by cutting from below - Quick setting for miter cuts - Workpiece clamping with adjustable vice and pressure piece - pneumatic tool clamping - Operation manual

Year of construction: 1983, Condition: used, Aluminum miter saw, underfloor saw, aluminum circular saw, aluminum semi-automatic circular saw, miter saw, glass bead saw -Saw blade diameter: 355 mm -Speeds: 1420/2880 rpm -Drive: 3.7/4.5 kW -with: coolant device Jvahl3 -Dimensions: 990/1140/H1535 mm -Weight: 596 kg

Year of construction: 2002, Condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. H2Xvmxm Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: used, Year of construction: 1998, saw blade diameter 450 mm cutting diameter 150 mm capacity 90 degrees: flat 330 x 40 mm capacity 45 degrees: round 140 mm capacity 45 degrees: flat 250 x 40 mm cutting speed 10 - 70 m/min B3Cqauuuww saw head feed 0 - 1000 mm/min sawing motor 1,7 / 2,6 kW weight of the machine ca. 1,1 t Accessories: used sawblade 450 mmø, material feeder M 45 NC für autom. run, ingoing roller track 7000 mm, outgoing roller track 4000 mm

Year of construction: 2000, Condition: ready for operation (used), Main Drive Spindle motor power 7.5 kW Additional Equipment Roller Tables: On the infeed side with rack for the measuring carriage Optional: Roller tables for the outfeed area Automatic Cutting Pressure Regulation: Yes Electronic Saw Blade Slip Monitoring: Yes Integrated Chip Tray: Yes Length Measurement: For profiles up to 21 m in length Pgjsxul This sawing machine was manufactured in 2000 by KALTENBACH. The KBS 851 DGNC features a miter tilting capability of -60° left and -50° right, accommodating material dimensions at 90° up to 850 x 500 mm. It supports various saw blade types including M2, M42, and M51, with a cutting speed range of 20-120 m/min. Includes an integrated chip tray and Proficut control software. Ideal for steel profile cutting in construction and trade. For more information about this sawing machine, please reach out to us. Application Types Sawing

Condition: ready for operation (used), Year of construction: 2002, Functionality: fully functional, machine/vehicle number: 300242, cutting range round at 90°: 460 mm, total length: 2,320 mm, total height: 2,570 mm, total width: 3,660 mm, overall weight: 7,500 kg, cutting range square at 90°: 600,460 mm, cutting diameter: 460 mm, space requirement height: 2,570 mm, space requirement length: 2,320 mm, space requirement width: 3,660 mm, cutting length (max.): 9,999 mm, working height: 720 mm, outer dimension length: 2,320 mm, outer dimension width: 3,660 mm, section length (max.): 9,999 mm, section length (min.): 8 mm, coolant pump power: 180 W, saw drive: 9,200 W, opening width: 600 mm, saw band width: 54 mm, saw band length: 7,470 mm, Equipment: rotational speed infinitely variable, BAND SAW KBR 460 NA A metal cutting band saw that combines high precision, power and automation. The KBR 460 NA from KALTENBACH is a solution designed for demanding production and industrial plants • High efficiency - a powerful main engine (7.5 or 9.2 kW) guarantees efficient and fast cutting. • Precision - infinitely variable cutting speed ensures perfect adjustment to any material. • Wide cutting range - supports round materials up to Ø 460 mm and square materials up to 600 x 460 mm! • Automation - possibility of setting sections up to 9999.9 mm long, which eliminates the need for manual operation. • Minimum waste - the automatic system allows you to leave a residual element only 30 mm long! • Stable and durable construction - weight 7500 kg guarantees reliability and long service life. Drggxf TECHNICAL DATA Weight: approx. 7500 kg Dimensions (L/W/H): 2320 x 3660 x 2570 mm Width with chip feeder (optional): 4650 mm Cutting band Dimensions: 7470 x 54 x 1.3 mm Cutting speed: infinitely variable (approx. 1-7) Working range Material dimensions • Round material: max. Ø 460 mm • Square material (W x H): max. 600 x 460 mm Cutting lengths • With single stroke: min. 8 - 760 mm • With multiple stroke: max. 9999.9 mm Min. residual length in automatic mode: 30 mm Working height: 720 mm Electrical data • Main motor: 7.5 or 9.2 kW • Hydraulic motor: 2.2 kW • Coolant pump: 0.18 kW • Chip feeder (option): 0.18 kW • Roller conveyor drive (option): 0.18 kW • NC positioning unit (option): 0.37 kW

Condition: good (used), Year of construction: 1997, Functionality: fully functional, For sale is a Kaltenbach cold circular saw. Gearbox free of play! Type: KKS 450 E Saw blade Ø: 450 mm Motor power: 1.8/2.7 kW Cutting speed: 10/20 13/26 15/30 m/min Feed rate: 0 - 1,000 mm/min Fast forward/reverse: 1,550 mm/min Max. working range: 150 mm Working range square material: 140 mm Working range flat material: 330x40 mm Working range round material: 140 mm Working range min.: 10 x 10 mm 150 Mitre range: 0° - 90° - 0° Dimensions LxWxH: 1,080 x 900 x 1,760 mm Weight: 1000 kg Inspection / collection in 89558 Boehmenkirch Shipping possible on request Forklift available for loading. B7Wmsf89T3

Condition: used, Year of construction: 1991, saw blade diameter 400 mm cutting diameter 130 mm capacity 90 degrees: square 120 x 120 mm capacity 90 degrees: flat 220 x 80 mm feed length 600 mm Dre8Wr feed length: multiple 1800 mm cutting speed 10/13/15/20/26/30 m/min mitre joint cuts -/+ degrees 60 total power requirement 5,5 kW weight of the machine ca. 1,8 t dimensions of machine L x W x H 2,45 x 1,20 x 2,00 m - mitre cutting +/- 60 ° with DRO - Accessories: new sawblade 400 mmø, coolant

Condition: used, Year of construction: 1983, saw blade diameter 400 mm cutting diameter 130 mm stroke 150 mm cutting range - square - 120 x 120 mm cutting range - flat - 300 x 40 mm capacity 45 degrees: round 130 mm capacity 45 degrees: square 110 x 110 mm capacity 45 degrees: flat 245 x 40 mm mitter cutting - all-position 90 ° cutting speed 13 / 25 m/min Ghcxisswv control minipos 807 total power requirement 4,3 kW weight of the machine ca. 850 kg dimensions of machine L x W x H 1,20 x 1,20 x 1,82 m Accessories: ingoing and outgoing rollertrack each approx. 4000 mm long, NC length stop, coolant