CNC machining center

HolzHer 7120

Condition: good (used), Year of construction: 1989, Pressing area 2550 x 1350 mm Number of press cylinders #6 Total pressing force 140 t Opening width approx. 400 mm Operating voltage: 3 x 400 V + N, 50 Hz. Gtsdswd N Rmopfx Ah Ssw Total connected load approx. 26 kW Space requirement (L x W x H) approx.: 3400 x 1600 x 2000 mm Weight: approx. 5500 kg Hydraulic hot plate press Down-piston design Electric hot platens Pressing pressure continuously adjustable via pressure switch Hydraulic pump Central control panel with all operating and Digital temperature display for both hot platens Press cycle counter Safety ripcord Rack compensation Main switch Note for used machines: • Errors in technical specifications and subject to prior sale. • Subject to change without notice. • Prices quoted are for pickup from the location - free shipping! • The machines have been cleaned and functionally tested. • All machines are sold as seen, without any warranty. The buyer is free to inspect the machines on site. • Special agreements are only possible in writing. (We will only respond to inquiries if you provide your address and telephone number!)

Condition: good (used), Year of construction: 2001, I sell the 3-axis CNC working centre HOLZ-HER UNI-MASTER 7226 with beam table Year 2001. Gedpfx Asi U Dxujh Setw Configuration: 3-axis main spindle recently full reconditioned / Water cooled Tool magazine 6 positions HSK63 on working head 1 grooving saw X-direction Drilling head 16+4 spindles Useful working area 3100x1360mm. 2 working fields, 4 clamping areas Automatic central system of lubrication. Holzher software controller with full instructions. 2x Pump SIEMENS ELMO-L S22 2,35KW. Good condition. Available immediately.

Condition: as good as new (ex-display), operating hours: 6 h, power: 4 kW (5.44 HP), volume flow: 0.57 m³/h, pressure (max.): 10 bar, type of cooling: air, Equipment: documentation/manual, refrigerant dryer, type plate available, RENNER industrial piston compressor with refrigeration dryer Gjdpfxsd Dhwns Ah Sjtw Suction capacity: 700 l/min (delivery rate: 570 l/min) Maximum pressure: 10 bar Pressure vessel: 270 l Motor output: 400V, 4.0 kW Dimensions: 970 x 795 x 1880 mm Upright design for industrial applications, robust belt guard, galvanized compressed air vessel according to AD2000 guidelines (with hand hole) with intercooler and aftercooler, anti-vibration mounts for effective vibration reduction, with refrigeration dryer, optionally with automatic condensate drain for refrigeration dryer and vessel; Various other configurations available

Condition: used, cut-off saw 3 KW Spindle diameter 50 mm Spindle length 300 mm Number of tools variabel St. Control CNC Dimensions (L/W/H) 2500x1700x2100 mm weight 1700 kg HABERKORN - FZS-2 Electronic Slotting Machine with Stepless Slotting Spindles and Automatic Roller Table ----- Crosscut Saw ----- Spindle Positioned at the Top Three-Phase Motor 3 KW Spindle Diameter 30 mm Speed ??2800 rpm Saw Blade Diameter 400 mm Gtodpfx Ahewgwlke Sjw * Automatic Brake with Speed ??Monitoring * Stepless Saw Positioning with Siko Display * Guard and Extractor Hood with 100 mm Diameter Extractor Nozzle 2 Slotting Spindles 50 mm Diameter ----- Power 2 x 7.5 KW Speed ??4200 rpm Spindle Diameter 50 mm Max. Tool Diameter Approx. 360 mm Usable Length 300 mm * Both slotting spindles can be positioned via ball screw * Freely programmable 19 programs, display with function keys * Protective and extraction hood with 180 mm diameter extraction nozzle * Automatic brake with speed monitoring Studio table ----- * Swivel range +/- 65° * Automatically changing counter wood (programmable) * Pneumatic clamp * High-precision electrical degree indicator * Automatic length compensation * Counter wood at any angle setting in the cutting plane Special features ----- Continuously adjustable roller table feed Laser for workpiece positioning Manual length stop LA 2000 Length 2500 mm Extraction nozzle diameter: 2 x 180 mm for slotting spindles 1 x 100 mm for crosscut saw ----- Price of the above-mentioned machine upon request! ----- Images show the same model. Original images not yet available. (Technical specifications according to the manufacturer - no guarantee!) All prices quoted are net, plus statutory VAT.

Condition: good (used), Year of construction: 2009, Brief Description of Basic Equipment ·      Console table ·      Automatic console positioning ·      Three-stage clamping element ·      Laser positioning aid for vacuum clamps ·      Vacuum clamps Main spindle 15 kW C-axis with aggregate interface Interface for Flex5 aggregate 30-position chain tool changer Tool holder HSKF 63 Drilling head with 13 spindles WoodWop package for CAD/CAM PC integration Rack and pinion drive for X and Y axis Ball screw for Z axis Z-axis travel: 600 mm Travel speeds: Vector speed: 113 m/min X and Y axis: 80 m/min Z axis: 30 m/min Free-standing electric cabinet. Homag control system Homag Homatic CNC System NC 83 with PLC control Remote diagnostics / telephone modem Technical Data Max. workpiece length: 4000 mm (all aggregates individually), max. 1375 mm with pendulum operation Tool diameter: 25 mm Single: 4175 mm / pendulum: 1550 mm Workpiece width (all aggregates): front 1150 mm, rear 1400 mm Workpiece thickness: 40 mm Milling operation, tool diameter 25 mm: front 1220* mm, rear 1550 mm *Workpiece thickness 40 mm Console table K Console length: 1340 mm Side stop rails Vacuum clamps Max. workpiece thickness: 300 mm with standard clamp max. 120 mm with mechanical clamping elements / clamping templates (customer-supplied) up to 80 mm with standard clamp Working height: 960 mm (underside of workpiece) PM basic equipment Automatic console positioning Three-stage clamping element Main spindle 15 kW (12 kW in S1 mode) Frequency inverter Spindle with hybrid bearings C-axis with aggregate interface Interface for Flex5 aggregate Vertical high-speed spindles Pneumatic lowerable loading stroke Two-stage clamping element for PM console Clamping device for post edge Three-stage clamping element for PM console Saw unit D= 280 mm Drilling/milling aggregate, 4-spindle for tool changer Lock case aggregate 2 Immediately available All information supplied without liability. Gtsdpfeyb Ndgex Ah Sjw Further technical data upon request. Individual tools may also be purchased at additional cost. The tools shown are NOT included in the base price!

Year of construction: 2012, condition: ready for operation (used), A Rotox bar processing machine for profile machining in window construction is available. Profile width range: 60mm-120mm, profile height range: 55mm-120mm, min. bar length: 300mm, max. bar length: 4650mm, axes: 3, output capacity: approx. 60-140 windows/shift. Machine dimensions X/Y/Z: approx. 10500mm/3500mm/2100mm, weight: approx. 4300kg. Documentation available. An on-site inspection is possible. Expected to be available August, 2026. Gtedpfxsxvru Ao Ah Sow

Condition: excellent (used), HOMAG BOF 211 – CNC Machining Center with 4-Axis Technology Reliable CNC machining center with extensive features and in notably excellent condition. — Technical Specifications • Machine type: CNC machining center • Axes: 4-axis technology (including C-axis) • Traversing paths X/Y/Z: approx. 6,000 × 1,400 × 150 mm • Control: HOMAG powerControl • Vertical main spindle: HKS • Tool changer: for multiple tools • Drilling heads: for vertical and horizontal operations • Aggregate interface: milling, drilling, grooving, sawing, etc. • Vacuum clamping system: matrix nesting or console table • Optional: edge banding and labeling — Features • Dimensional accuracy and repeat precision • Robust construction, well-maintained condition • Software support via HOMAG powerTouch / woodWOP • Suitable for furniture and interior fittings — The machine is available immediately. Dismantling and transport can be arranged by our service team upon request. — Contact Maschinenhandel Nord Gerstenstraße 2 17034 Neubrandenburg 📞 All prices net plus VAT. Subject to change and errors excepted. Gtodpsxk Tumjfx Ah Sjw

Condition: used, Year of construction: 2014, Used machine Year of manufacture: 2014 Features and technical data: - Working area X: 3,740 mm - Working area Y: 1,570 mm - Working area Z: 350 mm - 4th axis: available - 5th axis: 5-axis spindle, 12 kW motor - with additional C-axis locking - Tool changer positions: 24 with rotary magazine; 10 in the left side of the machine stand - Vertical drilling spindles: 12 - Machine table: console table - Table positioning automation: available - 6 workpiece supports, type e-motion - Special workpiece clamping system for frames - Software: FORMAT 4 WOOD FLASH, TPA ALBATROS Gtsdpfx Ahsx Hllxo Sow - 2 machining areas for pendulum operation - with automatic central lubrication - with mobile control panel with PC monitor - with air conditioning for control cabinet - with vacuum pump 90 m³/h - with hand-held control device - Included: 12 frame clamps, 8 large and 4 medium suction cups Availability: short-term Location: Röllbach

Year of construction: 2008, condition: ready for operation (used), Three small window and profile processing machines are available. 1) Urban WS 103 water hole cutter, year of manufacture: 2008. 2) Urban AKS 1105 single-head automatic welder with new cylinder. 3) Stegmaier AK 84 flat threshold for window frames, year of manufacture: 1984. On-site inspection is possible. Individual sale possible. Gtjdpfx Aewwvwyoh Sew

Condition: used, Year of construction: 1993, Used machine Year of manufacture: 1993 Features and technical specifications: - Spindle clamping length: 180 mm - Spindle tilt: -10° to +45° - Motorized spindle stroke with fine adjustment - Motorized spindle tilt - Motor: 5.5 kW - Table size: 1200 x 730 mm - Largest table opening: 420 mm - Motor brake - Speeds: 3000/4500/6000/7000/10000 rpm - Speed display - Extraction port: 125 mm - With Aigner integral fence - With 3-roller power feed Availability: approx. mid/end of January 2026 Gtsdpfx Aoxwz Rceh Ssw Location: Hesse