FomIndustrie Blitz Alva 450/500 ABC

FomIndustrie Blitz Alva 450/500 ABC

Condition: used, Year of construction: 2002, Machining dimensions (tool diameter 25mm): X=3015 mm Y=1483 mm Z=325 mm Max. travels: X=3268 mm Y=1483 mm Z=325 mm Max. programming speed: X/Y = 75 m/min / Z = 30m/min Tool holder HSK 63F Drilling unit 7964, 14 vertical drilling spindles with 32 mm grid (10 in x / 4 in y) Sawing unit 7946 3.6 kW, 90° pneumatically pivotable Milling unit 7933 9 kW Wood Her Vector axis (C-axis) Tool magazine (6 disk places) Hand control unit Laser device (positioning of the suction cups) PC control panel with 17" monitor Operating system Windows 2000 Software: TwinCAM32 - office version Vacuum pump 100 m³/h Dry running Selective safety mats (3-field division) Storage location: Nattheim Ijdpfx Ajvvi Nbschsti

Condition: refurbished (used), functionality: fully functional, Refurbished, six-piston hydraulic flatbed press of Italian manufacture. Branded veneer press for easy wood veneering, with warranty and service. Isdpfx Acjvvbbcjhoti Veneer sheet dimensions: 3000 x 1300 mm Pressure at full surface: 2.5 kg/cm2 Total maximum pressure: 90 tons Number of hydraulic pistons: 6 MYLAR Teflon film on the plates Prepared for water-based plate heating Option to install a hot water boiler Price includes complete machine refurbishment Price: 12,000 EUR (excluding VAT) The machine is refurbished, adjusted, and tested. The condition of the refurbishment and the machine's readiness for delivery must be verified in advance! In stock: Telnice near Brno, Czech Republic Testing, demonstration of the machine, and operator training are standard.

Condition: excellent (used), Year of construction: 2009, Machine Data: Panhans S 45 All in One Year of manufacture: 2009 Cutting length: 4200 mm Cutting width (programmable pusher travel): 4200 mm Angle stop on the left Roller tracks: 9 pieces, first 3 are dual-lane Clamping grippers: 8 pieces Air cushion tables: 4 pieces Central blower: 1 unit Technical Data: Saw blade protrusion: 70 mm, at 45°: 50 mm Saw carriage feed rate: forward 1-120 m/min, reverse constant 120 m/min Programmable pusher speed: forward 0-80 m/min, reverse 100 m/min Automatic cutting height adjustment; pressure bar height control Iedpfjyhnmgox Acheti Angle alignment device: min. alignment width 0 mm; max. alignment width full cutting length Main saw motor: 14 kW, main saw 350 mm diameter Scoring saw motor: 1.5 kW, saw 180 mm diameter Operating voltage: 400 V (+10%/-5%) / 50 Hz Electrical connected load: 20 kW Total weight: 6200 kg Control: VISIOLINE with PIOS Professional V2.0.0.x Labelling package incl. label printer

Year of construction: 2008, condition: ready for operation (used), Three small window and profile processing machines are available. 1) Urban WS 103 water hole cutter, year of manufacture: 2008. 2) Urban AKS 1105 single-head automatic welder with new cylinder. 3) Stegmaier AK 84 flat threshold for window frames, year of manufacture: 1984. On-site inspection is possible. Individual sale possible. Iedpfx Acjwwvwyehoti

Condition: good (used), Year of construction: 2010, Weinig Conturex C126 CNC Window production machine Description; Year of construction: 2010 Working width 40-260mm Working heigth 25-150mm Powergrip clamping table Table loading length single table 4 x 2280mm Workpiece length single table cycle 220-2700mm Table loading length double table (combined) 2 x 4630mm Workpiece length double table cycle without follow up 220-5000mm Workpiece length double table cycle with follow up 5000-6000mm Fully new PC & Software 2025 Full description on request Available approx. summer 2026 (Despite our great care all changes, mistakes in technical data, prices and all information is subject to (typing) errors. No guarantee on printed data! Availability subject to prior sales). Iedpfxox Tq I Ee Achsti (Alle Änderungen und Irrtümer in den technischen Daten, Angaben und Preisen vorbehalten! Keine Garantie auf gedruckte Daten!. Verfügbarkeit vorbehaltlich Zwischenverkauf). Prices excl. advertisement cost MachineSeeker / Preise exkl. Inserierungskosten MaschinenSucher Best woodworkingmachines from the Netherlands Holland Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland

Condition: excellent (used), HOMAG BOF 211 – CNC Machining Center with 4-Axis Technology Reliable CNC machining center with extensive features and in notably excellent condition. — Technical Specifications • Machine type: CNC machining center • Axes: 4-axis technology (including C-axis) • Traversing paths X/Y/Z: approx. 6,000 × 1,400 × 150 mm • Control: HOMAG powerControl • Vertical main spindle: HKS • Tool changer: for multiple tools • Drilling heads: for vertical and horizontal operations • Aggregate interface: milling, drilling, grooving, sawing, etc. • Vacuum clamping system: matrix nesting or console table • Optional: edge banding and labeling — Features • Dimensional accuracy and repeat precision • Robust construction, well-maintained condition • Software support via HOMAG powerTouch / woodWOP • Suitable for furniture and interior fittings — The machine is available immediately. Dismantling and transport can be arranged by our service team upon request. — Contact Maschinenhandel Nord Gerstenstraße 2 17034 Neubrandenburg 📞 All prices net plus VAT. Subject to change and errors excepted. Iedoxk Tumepfx Acheti

Condition: good (used), Year of construction: 2011, From a company liquidation: Itedpfx Ajwa Ecqjchoi Berg und Schmid VKS 370 HA Year of manufacture 2011 Semi-automatic machine 4-meter roller conveyor left + right Left stop with digital length measuring system, adjustable via handwheel Cutting capacity with a 370mm saw blade: Round 120mm - Square 100mm - Rectangle 180x100mm at 90° at 60°: Round 110mm - Square 90mm - Rectangle 90x100mm Miter cuts left up to 60° - right up to 45° Saw blade mount 40mm Saw blade speed 15-70 rpm 380 volts Coolant pump Semi-automatic function: 1. Clamp the material 2. Saw starts 3. Lower at rapid traverse to the beginning of the material or cut immediately for serial cutting 4. Remove the saw blade 5. Raise the frame until just above the material 6. Open the clamping jaw

Condition: reconditioned (used), Year of construction: 2014, functionality: fully functional, HOLZ-HER Edgebanding Machine ACCURA 1558 performance with BELT BRIDGE and intelligent equipment package for edge thicknesses up to 15 mm. Easy program selection and tool adjustment via the 18.5" color touchscreen (16:9). Short heating time for the GlueJet (GJ 301 automatic) adhesive system—around 2 to 3 minutes depending on adhesive type and ambient temperature. Always fresh glue thanks to the GlueJet adhesive application system and glue cartridges. Swapping PUR adhesive and cleaning the system is effortless and takes just a few minutes. Axis adjustment via high-precision, repeatable servomotors. Special configuration for protective film materials, such as high-gloss and super-matt! One of the absolute highlights of this machine is the multifunction package, which excels with businesses processing a wide variety of edges. The DIA tools are multi-stage and can switch between radius and chamfer as needed—from the longitudinal milling unit to corner copying and the profile scraper blade. The extendable workpiece support and the extended infeed area with air cushion table provide support for large workpieces. A guidance system assists in feeding small workpieces into the machine. Edge thickness (roll material): 0.4 – 3 mm (material dependent) Isdpfx Ajyfgrpjcheti Edge thickness (strip material): 0.4 – 15 mm Workpiece thickness: 8 – 60 mm Workpiece width: min. 65 mm Feed speed: 10 – 25 m/min Glue application with GlueJet in EVA and PUR quality, minimal effort required. Processes all standard edge types, including high-gloss & super-matt, as well as solid wood edges up to 15 mm. Motorized adjustment of the infeed fence Narrow part guidance system Prepared for connection to a RETURN system Motorized pressure bridge with top belt drive Multifunctional units for rapid changeover between radius, flush, and chamfer processing Spraying units, vertical & horizontal and much more. Delivery, installation, and commissioning of the machine can be offered directly by us for an additional charge. The machine is currently located at our delivery warehouse in Gratwein, Austria. In the event of discrepancies between the German version and any foreign-language version, the German version shall prevail. Our terms and conditions can be found on our website at holzher.de/en/terms-and-conditions.

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission Ijdpfx Acet Tqy Eshsti the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, Year of construction: 2018, 1 x CNC-CONTROLLED DRILLING, GLUING AND DOWEL INSERTING MACHINE GANNOMAT "INDEX 130 PRO" (with options as Index 180 Pro) 400V, 3Ph, 50Hz complete in standard design with: - Support with linear guide consisting of: 1 x single-spindle horizontal drilling unit, 1.1 kW motor, tool speed selectable via operator software (3000/5000/8000 rpm) 1 x blow-out, gluing and dowel inserting station in reinforced design for dowels Æ 8 mm, dowel length 30 mm - fully automatic, electronically controlled central lubrication - X-axis NC controlled, with working length 1300 mm, travel speed max. 78 m/min. - Z-axis, position via support table 5-40 mm programmable with NC-controlled Z-axis option - Dowel driving overhang of 7-20 mm, programmable with NC-controlled Y-axis option, drilling depth of 0-35 mm (with drill length GL 70 mm) is automatically set with driving overhang - Closed glue system with 6 bar glue pressure via glue nozzle, for glues with a viscosity of 150 to 350 mPas - Glue quantity continuously adjustable via operator software - GL/WATER selector switch for rinsing the glue system, 1 stainless steel container each for 5 kg glue and 5 l water - Control lamp for residual glue quantity display in the glue container - 1 side stop left, 1 side stop right and 1 center stop (all removable) - 4 start buttons for individual working with 1-4 workpieces - 4 pcs. Pneumatic inclined clamping cylinder 10° for workpiece thicknesses up to max. 80 mm, workpiece length (Y) min. 70 mm - 1 pc. suction funnel, connection Æ 80 mm - 1 pc. TCT control with: built-in industrial PC, incl. Soft PLC type Beckhoff TWINCAT, operating temperature range 0-50°C, TFT industrial display 15" resistive touchscreen, resolution 1024 x 768, CPU 2 GHz, 256 MB RAM, 2x network interface adapters, IDE hard disk, 4x USB rear, 1x USB front, operating system: WINDOWS 7 - programming via menu-driven user software, drilling distances freely programmable with ABSOLUTE, RELATIVE or GRID dimensioning, automatic workpiece mirroring and work step optimization, 4 work fields can be assigned with different programs, graphic workpiece display, parametric programming, 0-point shift, programmable work lists, error diagnosis with plain text OPTIONS: 1 electronic, optical glue monitoring system G.I.C. (Glue Insert Control) for 1 glue nozzle 4 vertical inclined clamping cylinders 10° with holder, additionally, (total 8 clamping cylinders) 1 surcharge for machine bed length 1800 mm with working length 1800 mm 1 surcharge for: 1 horizontal drilling unit, motor 1.5 kW, with multi-spindle drilling head with 3 individually controllable drilling spindles, pitch 32 mm arranged in X-axis, tool speed 3000 rpm. (The standard working length is not reduced) 1 Y-axis NC-controlled, with recirculating ball screw and dynamic traversing speed of 300 mm/sec. The dowel driving overhang 7-30 mm and the drill hole depth 0-42 mm can be programmed via software. (with drill length GL 77 mm) for vertical drilling unit drilling from TOP, Y-axis position 5-42 mm 1 surcharge Y-axis NC-controlled position 5-62 mm instead of 5-42 mm 1 surcharge for: 1 vertical drilling unit drilling from TOP, motor 1.5 kW, with multi-spindle drilling head with 3 individually accessible drilling spindles, 32 mm pitch arranged in X-axis, tool speed 3000 rpm. Y-axis position 5-42 mm, workpiece length (Y) min. 130 mm, (the standard working length is not reduced) 1 Z-axis NC-controlled, with K Itodpoxwaz Hefx Achei