Condition: ready for operation (used), Year of construction: 2021, operating hours: 200 h, functionality: fully functional, machine/vehicle number: 34, fuel tank capacity: 300 l, conveyor belt length: 6,900 mm, Only 200 operating hours! TECHNICAL DETAILS Godpfxszcd Aaj Abmeiu Undercarriage track: 400 mm with 3 grousers Rear belt: 6.9 m Shredding system: Size L (8 teeth) MACHINE DETAILS Additional hydraulic connection: 70 l/min Engine: Cat C7.1, 205 kW Fuel tank: 300 L Permissible total weight: 16,300 kg EQUIPMENT 24 V electrical control system Large radio remote control, complete Easy-to-maintain engine compartment with LED light Folding hopper with distance sensor and automatic control Hydraulically reversible fan wheel Audible start-up warning Tracked undercarriage with 2 travel speeds Frame for overband magnet Rubber quick-change pads Overband magnet Roller quick-change system on the roller Roller quick-change system on the machine Watering system LED work lights Additional electric pump for operation when the engine is stopped

Condition: used, Little used Proton OnSite C20 electrolytic hydrogen generation system made in 2018. The system was installed and tested but never put into operation due to owner dropping the project. Key information includes: Giodpfx Aszcwkkobmsu - Capacity: 20 Nm3/h, 760 SCFH, 359 SLPM, 43.3 kg/24 hours. - Purity: 99.9998%, water vapour

Condition: used, functionality: fully functional, Year of construction: 2015, machine/vehicle number: 75E-E188, USED SHRED-TECH DUAL SHAFT 80HP (TWIN 40) SHREDDER MODEL ST-75ES MANUFACUTRED 2015 TWIN 40 HP MOTORS DUTTING CHAMBER OF 956mm/37" X 635mm/25" DISCHARGE HEIGHT 1,067mm/42" Giodpfx Abexmthromou THIS WAS USED IN A PLASTICS COMPANY TO SHRED PLASTICS, CARDBOARD AND LIGHT GUAGE METAL. IT IS IN VERY GOOD CONDITION, PURCHASED DUE TO A PLANT CLOSURE. IT IS CURRENTLY LOCATED IN OUR WISCONSIN WAREHOUSE.

Condition: good (used), Year of construction: 2015, operating hours: 1,932 h, functionality: fully functional, Bale press Presto CC 50 M, year of manufacture 2015, with lifting and tilting device. Gjdszc Hz Eopfx Abmoiu Technical data: Manufacturer: Presto Type: CC 50 M Year of manufacture: 2015 Operating hours: 1932 Pressing force: 50 t Cycle time: 52 s Drive power: 7.5 kW Feed opening: 1030 x 1100 mm Feed volume: 0.85 m³ Tying: 3-wire, manually Throughput at a bulk density of: 35 kg/m³ - 1.3 t 60 kg/m³ - 1.7 t 100 kg/m³ - 2.2 t Bale dimensions: 750 x 1100 mm Bale weight: 300 kg Dimensions: 4705 x 1680 x 2540 mm (L x W x H) Machine weight: approx. 4000 kg Materials: Paper, cardboard, film The operating manual is available in German. Note: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find the video on our website or our YouTube channel. Please note: All technical data refers to the manufacturer's specifications. We assume no liability for the information provided or any errors. This offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: good (used), Year of construction: 2017, functionality: fully functional, Baler Presto CC 40 M, Year of manufacture: 2017 Technical Specifications: Manufacturer: Presto Model: CC 40 M Year of manufacture: 2017 Pressing force: 40 t Cycle time: 34 s Drive power: 15 kW Feed opening: 1080 x 1100 mm Feed volume: 0.85 m³ Binding: 4-fold, polyester strapping, manual Throughput rate at bulk density of: 35 kg/m³ - 1.8 t/h 60 kg/m³ - 2.5 t/h 100 kg/m³ - 3.1 t/h Gsdezc Hy Ujpfx Abmoiu Bale size: 750 x 1100 mm Bale weight: 400 kg Dimensions: 3650 x 1590 x 2010 mm (LxWxH) Machine weight: approx. 3,800 kg Materials: Paper, cardboard, film The baler is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Operating instructions and CE declaration are available. Note: Channel discharge is fully automatic and regulated. Please note: All technical data is based on the manufacturer's information. We do not accept liability for the information provided or any possible errors. This offer is non-binding, subject to prior sale, and may be revoked at any time. Inspections are possible by appointment. Sale is ex-works, prepayment required, without warranty or guarantee.

Condition: good (used), Year of construction: 2019, functionality: fully functional, Bale press Dixi 80 SLD, year of manufacture 2019, with lifting/tilting device Manufacturer: Dixi Type: Dixi 80 SLD Year of manufacture: 2019 Drive power: 11 kW, 400 V / 32 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Press cycle: approx. 35 s Capacity: approx. 1000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Gsdpezc Hyujfx Abmeiu Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. This offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by appointment. The sale is made against advance payment, ex works, without warranty.

Condition: good (used), Year of construction: 2019, operating hours: 1,022 h, functionality: fully functional, Baler Presto CC 20 M, Year of Manufacture 2019 Technical Data: Manufacturer: Presto Gisdpfx Ajzc Hv Njbmou Model: CC 20 M Year of Manufacture: 2019 Operating Hours: 1,022 Pressing Force: 20 t Cycle Time: 24 s Drive Power: 7.5 kW Filling Opening: 1030 x 750 mm Filling Volume: 0.53 m³ Tying: 3-fold, manual Throughput capacity at bulk density of: 35 kg/m³ - 1.6 t 60 kg/m³ - 2.3 t 100 kg/m³ - 2.8 t Bale Dimensions: 700 x 750 mm Bale Weight: up to 300 kg Dimensions: 3300 x 1235 x 1860 mm (LxWxH) Machine Weight: approx. 2,500 kg Materials: Paper, Cardboard, Film Remarks: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. A video is available on our website or our YouTube channel. Please note: All technical data is based on manufacturer information. We accept no liability for the details provided or any possible errors. Offers are subject to change, prior sale reserved, and can be revoked at any time. Inspection is possible by appointment. Sale is ex location, without warranty or guarantee.

Condition: good (used), Pearl mill, agitator mill, shredder, crusher, grinding mill, counter blade, crushing blade, counter cutter -Counter blade: Length 640 mm -Hole spacing: 173 mm / bore Ø 22 mm -Number: 3 knives available -Price: per piece -Dimensions: 640/150/29 mm Gedpfxjzcu Duo Abmjiu -Weight: 21.3 kg/pc.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Strautmann bale press, type BaleTainer, pressing force 60 t, year of manufacture 2012 Technical data: Manufacturer: Strautmann Umwelttechnik Type: BaleTainer Year of manufacture: 2012 Pressing force 60 t Total connected power 30 kW Bale dimensions 1,100 x 1,100 x 800 mm (W x D x H), 3 straps Bale weight up to 400 kg (3 straps) Binding: 4-fold vertical Dimensions: 5,348 x 2,113 x 2,752 mm (L x W x H) Gijdpjzcuz Tofx Abmsu Weight approx. 7,280 kg Materials: Paper, cardboard, PET bottles, film Note: The press is in good working order and has been inspected and tested. A video can be found on our website or YouTube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any errors that may occur. The offer is subject to change, subject to prior sale, and may be withdrawn at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: used, Article: Chip processing system Manufacturer: Lanner Type: Vetamat DS32 Yob: 2010, in 2025 completely refurbished The patented Vetamat system reliably separates metal chips from coolant. The systems achieve a throughput of up to 2,000 kg/h. The complete systems include a centrifuge, a chip conveyor with tank, a sump, and a control system. Depending on the type of material, you can choose between a parabolic centrifuge or a scraper-bottom centrifuge. Thanks to the modular system, the Vetamat system can be optionally expanded with a chip crusher, a large-part sluice, or a lifting & tipping device, as well as coolant treatment. - Very short commissioning time - Turnkey design - Minimal space requirements - Excellent accessibility - Modular system - Mounted on a WHG-compliant oil-tight sump - High operational reliability - Proven Lanner technology - Fully automatic operation with standby function - Expandable for long chips and coolant cleaning - Chip container under the centrifuge can be loaded from three sides Please, contact us for getting more information and pictures on mail(at) or Gsdpszcyfwefx Abmoiu *

Condition: refurbished (used), Year of construction: 2020, functionality: fully functional, Rotor for UNTHA XR3000C shredding plant. Completely refurbished (see current photos). Gsdpfozcdtljx Abmjiu

Condition: good (used), Year of construction: 2022, operating hours: 710 h, functionality: unexamined, Equipment: Methor chain basic package without shredding system - Crawler chassis including 2 driving speeds - Chassis chain 400mm 3-bar - Additional hydraulic connection 70 l/min - 24-V electric control - Large radio remote control complete - Maintenance-friendly engine compartment with LED light - Folding funnel with path sensor and automatic control - Hydraulically reversible fan wheel - Acoustic start-up warning - Paint finish: RAL 2011 deep orange Special equipment: Shredding system size L (8 teeth) Engine Cat C7.1, 205 kW Rear conveyor 6.9 m Giodpfx Abevrz Rvomeu Frame for overband magnet Overband magnet Irrigation

Condition: used, Year of construction: 2021, operating hours: 5,000 h, Equipment: Basic package Inventhor Type 9 MTU diesel engine 6R1300, 390 kW at 1,700 rpm meets EUROMOT V emissions standard Additional hydraulic connection 30 l/min and 70 l/min Roller drive via planetary gear 380 kW – VARIO - Load sensing system Fuel tank 950 liters Longitudinal belt: belt length 4,450 mm, belt width 1,000 mm Centrally arranged lubrication strips 24 V electric control Additional electric pump for operating the following functions when the engine is not running. Raise/lower/fold rear belt, open/close comb flap, open/close comb, raise/lower optional permanent magnet belt, raise/lower optional folding funnel Gisdpovnmldjfx Abmsu Radio remote control complete Large side GRP maintenance doors Maintenance-friendly engine compartment with LED light Hydraulically reversible fan wheel Loading protection on both sides Fire extinguisher Maintenance ladder Tool box Acoustic start-up warning Doppstadt telematics system Paint: RAL2011 deep orange Special equipment: 500 mm chain chassis unit Chain chassis 500 mm flat Crushing system size "L" -VARIOMAT Size "L" - "Limiter" (20 pieces) Rear conveyor length 7 m 1200 mm wide LED light package engine compartment and rear Irrigation with funnel attachment H=300mm Frame for overband magnet Overband magnet 2 t permanent

Condition: good (used), Year of construction: 2022, operating hours: 2,806 h, functionality: fully functional, Equipment: Basic Package Inventhor Type 6 Load-sensing system Fuel tank 500 liters Longitudinal conveyor: length 2,900 mm, width 800 mm Centrally arranged lubrication strips 24V electronic control – additional electric pump to operate the following functions when the engine is off: "raise/lower/fold rear conveyor, open/close comb flap, open/close comb, raise/lower folding hopper" Complete radio remote control Large side GRP maintenance doors Maintenance-friendly engine compartment LED lighting package: engine compartment and rear Hydraulically reversible fan Three-sided loading protection Folding hopper Fire extinguisher Service ladder Toolbox Acoustic start-up warning Doppstadt telematics system Paintwork: RAL2011 deep orange Special Equipment: Powertrain 310 kW - EV 3-axle drawbar trailer chassis unit Shredding system Size L 600/4 - 30 Z Additional hydraulic connections 35 - 80 l/min Hydraulic drive Rear conveyor 4.9 m Overband magnet neodymium Frame for overband magnet Giedpfx Ajwnfwqebmju

Condition: used, Year of construction: 2021, operating hours: 3,304 h, functionality: fully functional, Basic Package AK 640 SA Mercedes / MTU diesel engine 6R1500, 480 kW at 2,000 rpm Semi-trailer chassis with 3 axles, road approval for 80 km/h Brake system incl. ABS and lighting according to EU directive Tyres 385/65 R22.5 Permissible total weight 32,000 kg Hydraulically adjustable support legs Splash protection (internal and lateral mudguards) Mercedes / MTU diesel engine 6R1500, 480 kW at 2,000 rpm, complies with EUROMOT V emission standard Additional hydraulic connection 20 l/min Load-dependent control of material feed incl. automatic scraper floor reversal Separate drive for feed roller and scraper floor (twin drive) Fuel tank 2 x 450 litres Feed roller: length 1,690 mm, diameter 510 mm, with attached tooth segments Four-row flail drum with 36 free-swinging cast steel flail holders and replaceable flail tips Standard: Flail tip "Streusel plus" Impact plate with teeth Centrally positioned wear strips Electric pump for actuating cylinder functions (e.g., raising/lowering support legs and opening/closing rear hopper, folding/unfolding rear conveyor, releasing drive system) when the engine is off 24 V electrical control Separate control box at rear of machine Hydraulically foldable fine shredding basket Multimesh (mesh size from 30 to 280 mm, gradations upon request) incl. one-piece rear flap Rear conveyor: belt length 7,500 mm, belt width 1,500 mm, discharge height 5,200 mm, hydraulically foldable and lowerable from 39° to 30°, incl. anti-magnetic central section Under belt: belt length 3,800 mm, belt width 1,400 mm Moistening device for external water connection Scraper floor with 71 slats Wear protection in the drum section Reinforcement plates on the infeed hopper (wear-resistant steel) on both sides for side wall Complete radio remote control Fire extinguisher Acoustic start-up warning Doppstadt telematics system Paintwork: RAL 2011 deep orange Additional Equipment: Hydraulic drive Giedpsxx Tigefx Abmsu Scraper floor chain lubrication NEODYM overband magnet Frame for overband magnet Central lubrication Engine compartment protective plate Lighting package: engine compartment and rear conveyor Watering system Delivery date to be arranged Available from 06/2026

Condition: used, Year of construction: 2022, operating hours: 3,250 h, functionality: fully functional, Basic package Inventhor 6: Load-sensing system Fuel tank 500 liters Longitudinal conveyor: belt length 2,900 mm, belt width 800 mm Centrally positioned wear/slide strips 24-V electric control system – additional electric pump enables the following functions with engine off: raise/lower/fold rear conveyor, open/close comb flap, open/close comb, raise/lower folding hopper Complete radio remote control Large side GRP maintenance doors Service-friendly engine compartment LED lighting package: engine compartment and rear Hydraulically reversible fan wheel Three-sided load protection Folding hopper Fire extinguisher Maintenance ladder Toolbox Acoustic start-up warning Doppstadt telematics system Painting: RAL2011 deep orange Optional equipment: Driveline 310 kW – EV Gijdpfx Aexx N T Iebmsu 3-axle drawbar chassis unit Shredding system Size L-C3 600/4-30Z Size L limiter Auxiliary hydraulic connections 35 – 80 l/min Hydrostatic drive Hopper extension 350 mm, left-side watering Rear conveyor 7 m Overband magnet Neodymium Frame for 7 m overband magnet Central lubrication system Custom paint finish in RAL Delivery date to be arranged

Condition: used, Year of construction: 2022, operating hours: 4,561 h, functionality: fully functional, Basic Package AK565: Central axle trailer chassis with 2 axles, road approval for 80 km/h Brake system incl. ABS and lighting according to EC directive 50 mm EC drawbar eye incl. slip-on coupling Tyres: 385/65 R22.5 Hydraulically adjustable support leg Splash guards (inner and side-mounted fenders) Permissible total weight: 19,000 kg MTU diesel engine 6R1300, 390 kW at 2,000 rpm, complies with EUROMOT V emission standard Exhaust discharged upwards Load-dependent material feed control incl. automatic reversing of scraper floor Fuel tank, 450 L Feed roller: length 1,690 mm, diameter 510 mm, fitted with bolt-on tooth segments Four-row flail drum with 36 free-swinging cast steel flail holders and replaceable flail tips - Dopplock system Standard: Flail tip “Streusel plus” Centrally arranged lubrication strips Electric pump for operating cylinder functions (e.g. raising/lowering the support leg and opening/closing the rear basket, folding/unfolding the rear conveyor, releasing the drive) when engine is stationary 24 V electrical control system Separate control panel at the rear of the machine Hydraulically folding fine shredding basket “Multimesh” (mesh sizes between 30 - 280 mm, gradations on request) incl. one-piece rear flap Scraper floor with 32 slats Chain drive for feed roller and scraper floor Complete radio remote control Drive preparation Rear discharge conveyor, 4 m long, 1,800 mm wide “classic” Anti-magnetic centre section on the discharge conveyor Reinforcement plates (Hardox) on both sides of feed hopper sidewall Fire extinguisher Acoustic start-up warning Doppstadt telematics system Finish: RAL2011 deep orange Optional Equipment: Hydraulic drive 600 L fuel tank Flail tip C1 “Bear Paw” with carbide insert Rear discharge conveyor 4 m, belt width 1,800 mm, lowerable Neodymium magnetic pulley incl. chute Separate drive for feed roller and scraper floor (“Twin Drive”) Duomatic coupling Smooth impact plate Fine shredding basket Gijdpfx Abeyhckmemou Delivery date by arrangement

Condition: used, Year of construction: 2022, operating hours: 1,518 h, functionality: fully functional, Basic package Inventhor 6: - Load-sensing system - Fuel tank 500 liters - Longitudinal conveyor: belt length 2,900 mm, belt width 800 mm - Centrally arranged wear strips - 24V electrical control system – additional electric pump for actuating the following functions when the engine is off: - Raise/lower/fold rear conveyor, open/close comb flap, open/close comb, raise/lower folding hopper - Complete radio remote control - Large side GRP service doors - Maintenance-friendly engine compartment - LED lighting package: engine compartment and rear - Hydraulically reversible fan - Three-sided loading protection - Folding hopper - Fire extinguisher - Maintenance ladder Gjdpfexx N Dgsx Abmjiu - Toolbox - Acoustic start-up warning - Doppstadt telematics system - Paint finish: RAL2011 deep orange Additional equipment: - Driveline 260 kW – EV - 2-axle semi-trailer chassis unit - Size L shredding system – 20 teeth - Size L limiter - Additional hydraulic ports 35–80 l/min - Hydraulic travel drive - Hopper extension 350 mm, watering system both sides - Hopper wedge Size L with NM brush - Rear conveyor 7 m - Overband magnet neodymium - Frame for 7 m overband magnet Delivery date by arrangement

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: Godozbxwiepfx Abmsiu The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, overall weight: 9,500 kg, year of last overhaul: 2025, filling opening width: 420 mm, filling opening length: 1,250 mm, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Gsdpfjzbxvlox Abmoiu Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The packing press has been fully overhauled in our workshop. The press is in very good condition; please see the demonstration video following the overhaul. The machine sustained transport damage whilst being moved. The control cabinet was damaged and slightly dented by a forklift truck, and the main switch (on/off switch) was damaged. These damages are reflected in the significantly reduced sale price and must be repaired by the buyer at their own expense. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Used Thetford International T3 waste compactor. Godpfx Abohvi Ahemjiu

Condition: ready for operation (used), Drum Screen Terra Select. 50 mm screen perforation Godpevnmcvjfx Abmeiu

Condition: good (used), Year of construction: 1990, Roll compactor, Bergmann – used: Price ex works: only €950 (net) Manufacturer: Bergmann Type: PS 8100E Year of manufacture: 1990 Serial number: 05 3658 2845/90 Pressing pressure: to Weight: 750 kg 400V, 5.5 kW Condition: good Available: from Q4/2026 Location: Hamburg Giedozbygropfx Abmsu Efficient waste compaction: A special steel drum enables effective collection, shredding and compaction of the waste, reducing its volume up to ninefold. Continuous filling: The machine allows for continuous filling by all users. The feed shaft can also remain open during the working process, which facilitates and accelerates waste compaction.

Condition: good (used), Year of construction: 1999, Baling presses, HSM, 30-ton pressing force – used: Giedpfx Aozbygfobmou Price ex works: only €2,950 (net) Manufacturer: HSM Type: 225.1 VL Year of manufacture: 1999 Machine number: 6124.834. N Serial number: 200014505 Pressing force: 30 tons 400V, 5.5kW Condition: good Available: from Q4/2026 Location: Hamburg

Condition: good (used), Year of construction: 2014, Large waste compactor / cardboard press, Höma, – used: Price at location: only €18,950 (net) for self-dismantling! Manufacturer: Höma Giodpfx Abjzbyf Ismsu Type: PB4000 Year of manufacture: 2014 Machine number: 140409 Weight: 1,200 kg Pressing force: not specified, but we estimate 40 tons. The press has a second discharge chute. Price includes a small crane with trolley. 30 kW Condition: good Available: from Q4/2026 Location: Hamburg For an additional charge, a conveyor system for empty cardboard boxes, over 100 m long, is available! Photos at the end of the advertisement!