Twin screw extruder

Weber DS 7.22

Condition: ready for operation (used), Year of construction: 1995, operating hours: 39,000 h, functionality: fully functional, Equipment: documentation/manual, A used and functional profile line for rigid PVC-profiles (300 x 100 mm), consisting of: Twin-screw extruder (parallel) Manufacturer: WEBER Type: DS 7.22 Year of manufacture: 1995 Machine no.: DS70-043 Operating hours: 39,000 hours Screw diameter: 70 mm Effective screw length: 22 x D Screw geometry: for rigid PVC profiles Torque: 4,500 Nm per screw Screw speed: max. 40 rpm, continuously adjustable Drive motor: DC low-voltage motor, thyristor-controlled Drive power: approx. 25 kW Cylinder heating/cooling zones: 5/3 (air cooling with fan) Adapter heating zone: 1 Tool heating zones: 5 Control: conventional control with digital temperature controllers Degassing: Busch rotary vane vacuum pump (1.5 kW) Output capacity, max.: 120-150 kg/h for hard PVC, depending on material Klsdpfx Ahjyhcabswsn Connected load: approx. 50 kW (without tool) Special accessories: Mass temperature sensor and mass pressure sensor Adapter between extruder connection and extrusion tool Used tool set for a window profile (widening), consisting of: - Extrusion tool ‘widening’, incl. heating bands - Dry calibration - Vacuum tank approx. 2 m long, with 8 slots for calibration discs - 16 calibration discs Vacuum calibration unit Manufacturer: Uniplast / Greiner Type: CAL VAK 4P Year of manufacture: 1992 Machine number: K9209590 Total length: 6500 mm Vacuum pumps: 4 x Speck vacuum pumps (4.3 kW each) Water circulation pumps: 2 x Calpeda (1.1 kW each) Caterpillar haul-off, incl. attached saw Manufacturer: Uniplast / Greiner Type: CAT PUL 2D Year of manufacture: 1992 Machine number: R 9204546 Haul-off: Effective contact length: 2000 mm Pad width: 250 mm Haul-off force, max.: approx. 25000 N Speed range: approx. max. 10 m/min. Profile saw: HM circular saw blade: Ø 450 mm Profile cross-section, max.: approx. 300 x 100 mm Tilting table Manufacturer: Ide Type: ME N 52/2 Year of manufacture: 1994 Length: 6000 mm Support width: 270 mm Note: The complet profile line was overhauled in 2020 and has only been in operation for 325 hours since then.

Condition: used, machine/vehicle number: 10460, 5-blade rotor 2 rows of stator blades Rotor diameter 400 mm Working width 600 mm Inlet cross-section approx. 500 x 600 mm Kledsghgg Uepfx Ahwsn

Condition: used, Year of construction: 1997, functionality: fully functional, machine/vehicle number: 035, Single screw PVC extruder Kljdpjxgh Dzofx Ahwjn

Condition: used, machine/vehicle number: 12861, Rotor diameter: 400 mm Rotor width: 600 mm 3-knife rotor 2 rows stator knives Inlet cross section approx. 400 x 600 mm Klodpfxsnn Nbas Ahwon Drive motor: 22 kW

Year of construction: 1991, operating hours: 102,364 h, condition: good (used), This extrusion line from Hans Weber GmbH is in machine storage at Plastima Used Machinery. The line is from 1991 and is in used but good condition. Kledpfoqpft Iex Ahwsn - Brand: Hans Weber GmbH - Model: WEBER DS 6.5 - Year of construction: 1991 - Screw Ø: 65 mm - Working hours: 102.364

Year of construction: 1970, condition: ready for operation (used), A complete extrusion line with a Reifenhäuser extruder and a gravimetric system Plast-Control (2006) is available. 1) Unwinder 1. 2) Primer unit and hotmelt unit for water-based adhesive lamination. 3) Dryer. 4) Unwinder 2. 5) Dolci extruder for extrusion lamination. 6) Unwinder 3. 7) Two printing units with additional dryer. 8) Extruder Reifenhäuser. 9) Rewinder. 10) Guide roller in the basement. 11) Web guiding under unwinder 1 in the basement. 12) 2x resin silos in the basement. This is a complete extrusion line with peripheral equipment. Documentation available. An on-site inspection is possible. Klsdpfew R Dhrox Ahwjn

Year of construction: 1996, condition: excellent (used), film width: 1,300 mm, Used single-layer blown film extruder for sale in excellent condition, featuring a 150 mm die diameter and a production capacity of up to 100 kg/h. Model: Queens EP-65N Processable materials: LLDPE/LDPE/MDPE/HDPE/other blends. Screw diameter: 65 mm Head: • Blown film die head • Die diameter: 150 mm Die gap: 1.2 mm Output: Up to 100 kg/h, depending on material composition • Maximum speed: 120 m/min • Winding width: 1300 mm - Flying knife roll slitting Accessories included: • Tower • Gravimetric weight control system • Masterbatch dosing unit • Calibration cage The machine can be inspected in operation. Kodexrb Hmepfx Ahweln Offered with spare parts.