Shock test chamber

Vötsch VT 7012 S3

Year of construction: 2018, condition: excellent (used), Vötsch VT³ 7012 S2 Temperature Shock Test Chamber Manufacturer: Vötsch Industrietechnik GmbH Type: VT³ 7012 S2 Year of Construction: 2018 Machine Type: Temperature Shock Test Chamber / 2-Chamber Shock Test System Test Chamber Volume: 125 liters For sale is a used Vötsch VT³ 7012 S2 temperature shock test chamber with a 2-chamber system and programmable touch panel control. The system was developed for rapid and abrupt temperature changes and is particularly suitable for Environmental Stress Screening (ESS), environmental simulation, electronics and component testing, research and development, as well as quality assurance. Nsdpfxjzzazuo Apholg The test specimen is transported between the hot and cold chambers via a vertically moving transport carriage. Technical Data: Temperature Range, Hot Chamber: +50 °C to +220 °C Temperature Range, Cold Chamber: -80 °C to +70 °C Test Chamber Volume: 125 liters Number of Chambers: 2 Max. Test Weight / Carriage Load: 50 kg Refrigeration Unit: water-cooled Mains Connection: 3/N/PE AC 400 V ±10 % / 50 Hz Rated Power: 10 kW Rated Current: 25 A Refrigerant: Refrigerant 1: R449A Refrigerant Quantity: 1.70 kg GWP: 1,397 CO₂ Equivalent: 2.37 t Max. Low Pressure: 22.5 bar g Max. High Pressure: 25 bar g Refrigerant 2: R23 Refrigerant Quantity: 1.27 kg GWP: 14,800 CO₂ Equivalent: 18.80 t Max. Low Pressure: 22.5 bar g Max. High Pressure: 25 bar g Standby Pressure: 14 bar g Dimensions: Test Chamber (W × D × H): 470 × 650 × 410 mm External Dimensions (W × D × H): 970 × 2,350 × 1,985 mm Required Room Height for Operation: approx. 2,450 mm Equipment: 2-chamber temperature shock system Vertically moving transport carriage Programmable touch panel control CONTROLPAD for status display Observation window Test chamber lighting Cable gland Water-cooled refrigeration unit Automated and programmable defrost cycles Operating hour counter Cycle counter / Remaining time display USB and Ethernet interfaces Application Areas: Temperature shock testing Environmental Stress Screening (ESS) Environmental simulation Electronics and component testing Assembly testing Material testing Quality assurance Research and development Reliability testing Life and stress tests Transport Data: Dimensions (L × W × H): approx. 2,350 × 970 × 1,985 mm Weight: to be determined Transport by freight forwarder Condition: Used Optical condition as shown in the pictures. Scope of Supply: Vötsch VT³ 7012 S2 temperature shock test chamber Touch panel control Equipment and accessories as shown in the pictures Availability: by arrangement. Scope of supply as shown in the pictures. Subject to changes, errors and prior sale.

Condition: good (used), Year of construction: 1998, Press Force 315.00 t Stroke 500 mm Throat 425 mm Installation Height (Upward Stroke) 1,000 mm Table Surface 1,200 x 815 mm Table Height above Floor 800 mm Ram Surface 1,100 x 700 mm Speed Down 48 mm/s Speed Up 330 mm/s Working Speed 19 mm/s Njdpfx Asv Rwu Uephelg Oil Volume 1,600 l Power Requirement 82.0 kW Weight 23.00 t Dimensions (WxDxH) 2.4 x 2.8 x 4.0 m For Permitted for manual loading according to the CE standard with oil-hydraulic drive, controllable depending on pressure/time and travel, light-guard at the front (Sick), two-hand operation permitted for manual loading according to the CE standard with oil-hydraulic drive, controllable depending on pressure/time and travel, light-guard at the front (Sick), two-hand operation

Condition: refurbished (used), Year of construction: 2001, functionality: fully functional, Completely overhauled, 12-month warranty, available immediately. Equipped with a safety system for solvent-based substances in accordance with DIN 1539, including exhaust fan, supply air cage filter, as well as concentration monitoring and a recirculation air filter wall in the interior. - Internal dimensions (W x D x H): 1000 x 1000 x 1500 mm - External dimensions (W x D x H): 1900 x 1430 x 2315 mm - Capacity: 1500 liters - Tmax: 300°C - Eurotherm controller 2404 (20 programs, each with 16 segments) - Eurotherm recorder - Connected load: 29 kW - 6 wire shelves included, plus V2A support brackets - Minimum exhaust air flow rate: 360 m³/h - Maximum permissible solvent quantity: 36g at nominal temperature of 300°C - With concentration monitoring - New window seals - Net weight approx. 1200 kg - Includes documentation, CE declaration Nodjvcb U Aopfx Aphjlg - Electrically tested and with DGUV test protocol Inspection in our warehouse by appointment. We offer new and used industrial ovens. Get in touch with us! Oven, ovens, drying oven, furnace, heat oven, heating cabinet, industrial oven, paint dryer, annealing oven, heating oven, tempering oven, drying cabinet, chamber oven, baking oven, recirculation drying cabinet, recirculation oven, solvent oven, chamber recirculation oven

Year of construction: 2009, condition: ready for operation (used), Connected load: 18kW, was overhauled in 2017, an inspection is possible. Nledpen Htktofx Aphjg

Year of construction: 2004, condition: reconditioned (used), Stock-No. 2054 Nlodpfoiyya Aox Apheg 1used, partly overhauled and functionally tested Single-screw extruder AlphaTec A-ES 75.28 Screw –Ø 75 mm- 28 LD main drive 75 kW- AC Screw speed up to 80 r.p.m. - adjustable 1x venting port with vacuum-pump cylinder barrel heating apporx. 30 kW installed 3x additional temperature controller for down-stream equipment Control board overhauled You´re welcome for inspection visit in our stock Wuppertal-Germany More extruders available

Condition: good (used), Filtration Plant, make Seitz Orion, 100 x 100, for 180 hl/h, in 2002 overhauled, consisting of: - Kieselguhr-frame filter, with 29 kieselguhr frames in s/s, outside lying raising pipes, sight glass armatures with pressure manometer, with kieselguhr discharge tub with screw in s/s, with kieselguhr dosage unit Nodjrai N Ajpfx Aphjlg - Sheet filter with 150 stainless steel plates, outside lying raising pipes, sight glass armatures with pressure manometer - operating platform between both Filter, stairs at DE-Filter - Control cabinet

Year of construction: 2013, condition: excellent (used), Vacuum THERMO oven, max temperature 200°C Nsdpfxjxcb H Uo Aphjlg

Condition: used, Year of construction: 1971, pressure 200 t passage width NA mm stroke 180 mm Nsdjt Hw Dwopfx Aphslg table length 690 mm table width 530 mm distance between columns 420 mm total power requirement 18 kW weight of the machine ca. t dimensions of the machine ca. m Hydr. 4-Pillar Press for Embossing/Calibration

Condition: good (used), Year of construction: 1989, Power: 1.000 kN Size of bolster: 800 x 750 mm Distance betw. columns: 900mm Nsdpjd E U Nnefx Apholg Size of ram: 800 x 600mm Daylight: max. 800 mm Stroke: 480 mm Speed: Fast down: 300 mm/s Working: 30 mm/s Fast up: 300 mm/s Electric power total: app. 31 kW Weight: app. 13.000 kg Size of footprint: app. 1,6 x 2,90 x 3,8m (T x B x H) • die cushion, activ, 400kN, stroke 200mm • allowed for 2-hand working • equipped by oil - air chiller • ram guiding by 4 pc. hard chromed Guiding columns

Year of construction: 2026, condition: new, functionality: fully functional, total length: 900 mm, total width: 1,550 mm, total height: 1,900 mm, input voltage: 230 V, laser power: 30 W, laser wavelength: 1,064 nm, type of cooling: air, type of input current: AC, The universal laser marking system LAS 28 XLe from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes an integrated PC with Windows operating system and laser software. Optionally, the laser model LAS 28 XLe can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extension arms for marking long parts, movable Z-axis, drawer systems, etc., can be realized. Made in Germany Nlodpfxounh H So Aphsg Fiber laser 30W, 20 W or 50 Watt - Laser class 1 - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - marking software EZCAD in German / English - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: autofocus system - optional: exhaust system (incl. activated carbon filter) - pilot laser (simple preview, contour preview) - focus finder (simple focus adjustment) - signal light for indication of operating status - max. component height approx. 300mm - electrically adjustable Z-axis - Integrated PC with Windows operating system - frame made of aluminum profile - air cooled - Door width approx. 700mm / door height(pass-through): 400mm - Connection 230V - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) - Weight: approx. 100 Kg