Mesh welder

Schlatter MG-230

Condition: excellent (used), Year of construction: 2003, working width: 215 mm, welding power (max.): 750 kVA, Complete Mesh welding/Lattice girder factory Itsdpfxjqy Ek Ae Ad Nob Factory consists : - Mesh welding line SCHLATTER PG 24 , Semi- automatic , Year - 2002 - Lattice Girder Line SMEI , Full automatic , Year - 2003 - Straightening and cutting machines 1x Wafios R4 2 x VITARI NR16 1X VITARI NR10 - Cold drawing line SMEI , Input wire max.10mm, Speed - 4m/sec. - But welding achine SMEI - Wire sharpener SMEI

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped Isdpfswu Tu Dsx Ad Netb WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Year of construction: 2009, condition: new, belt dimensions 2000x100mm Belt speed 30m/sec Angle adjustable from 30 to 90 Power 3kW 4000V50Hz Weight 200kg Itodpfx Ajx Davod Njb Rollers for grinding rye 3/4";1/2"; 1"; 11/4"

Year of construction: 1999, condition: used, Lattice girder line PITTINI IMPIANTI (Italy) Brand name – Pittini Impianti ( made in Italy) Built year – 1999. Still installed, under power, production stoped 5 years ago. Min – Max UPPER longitudinal wire diam. - 5,00 – 12,00 mm Min – Max LOWER (2 wires) longitudinal wire diam. - 4,20 – 12,00 mm Min – Max Fret(zig-zag) wire diameter – 3,60 – 8,00 mm Min – Max lattice girder height – 90 – 250 mm Lattice girder base width – 100 mm Lattice girder pitch – 200 mm Min - Max. Cutting length (run-out table) – min. 3,60 m - max 12 meters. Min. Cutting length – 200 mm Max speed (capacity) – 24 meters per minute Itodpfsikvg Nox Ad Neb Power – 380 V , 50 Hz Total installed power – 85 kW

Condition: excellent (used), Year of construction: 1992, Manufacturer EVG Type TSD 7-25 Machine No. 958 Year of manufacture 1993 Working direction L > R Beam types KT 8… Beam height (mm) 90-250 Carrier length min. (mm) max. (mm) 14,000 Fixed lengths: Yes Cutting pitch (mm) 100/200 Spool unwinder (pcs.) 5 Itedpfjwp Ilyjx Ad Nob LAR: Yes Wire diameter - 5-12 mm smooth/ribbed Diagonal - 4-7 mm smooth / ribbed Stack height max. (mm) - 500

Condition: used, Year of construction: 1983, Used machine Year of manufacture: 1983 Condition: fully checked and serviced, including a new feed belt Features and technical specifications: - Including combination unit with contact roller and sanding shoe - With height-adjustable contact roller for calibration - With workpiece-controlled air cushion pressure shoe - 4-way adjustable grit compensation - With pneumatic belt tensioning device - With a rotating cleaning brush at the outfeed side of the machine Itodpewka T Sjfx Ad Njb - Sanding width: 1350 mm - Sanding belt length: 1900 mm - Pass-through height: 150 mm - Main motor: 15 kW - Continuously adjustable feed speed, 2.5 - 12.5 m/min - With roller table at the infeed - With digital display for the electrically driven workpiece thickness adjustment - Extraction ports: 2 x 200 mm Dimensions: approx. 2300 x 2000 x 2300 mm Weight: approx. 2300 kg Images show the machine in unrefurbished condition! Availability: approx. end of January 2026 Location: Röllbach

Condition: as good as new (ex-display), Year of construction: 2021, Because of CANCELLED PROJECT of the construction of a nuclear power plant, we are able to offer you.... NEVER USED - complete metal forming / processing plant (about 80 machines) Iedpfx Aovlimlsd Njtb Please contact us for full machinery list and more photos. Thank you!

Condition: used, Year of construction: 1990, Used machine Year of manufacture: 1990 Features and technical data: Max. working width: 1100 mm Min / max. workpiece thickness: 3 / 160 mm Itjdpfx Adewxh Due Nob Sanding belt dimensions: 2150 x 1120 mm Sanding belt speed: 18 m/sec Feed speed: 4 + 8 m/min Sanding unit motor power: 15 kW Feed belt motor power: 1.1 / 1.8 kW Operating pressure: 6 bar Air consumption: 20 l/min Extraction nozzles: 2 x 150 + 1 x 120 mm Dimensions: 2690x1800x2100 mm Weight: approx. 3500 kg Note: Machine is not operational (feed belt is missing) Storage location: Flörsheim Availability: by arrangement

Condition: used, functionality: fully functional, STILMEC90 Press Brake, 8.5 m WORKING LENGTH: 8500 mm BENDING FORCE: 90 TON STROKE: 150 mm MODEL: GS85AB YEAR OF MANUFACTURE: 2005 / REVAMPING: 2022 DIE FOR HEM BEND Itodswg Ec Rspfx Ad Nsb FULLY FUNCTIONAL

Condition: used, Year of construction: 1990, Used Weber wide belt sanding machine with 2 sanding belts, oscillating. Infinitely variable feed speed. Sanding width 900 mm. Used as a backup machine. Iodpfowzlqksx Ad Njtb