Multicolor powder coating machine

Proton STR-Smart

Year of construction: 2019, condition: as good as new (ex-display), Komplette Anlage - sofort lieferbar Pulverkabine KPZ-4 PSN Automatische Waschanlage (2-Zonen) Gas-Ofen mit Umluft SGS-80O Handschiebebahn Bljdpfx Asfnuklodusr Preis ab 99.999,00 € Netto

Condition: new, Year of construction: 2025, functionality: fully functional, power: 88 kW (119.65 HP), temperature: 220 °C, heating capacity: 30 kW (40.79 HP), workpiece height (max.): 1,500 mm, workpiece length (max.): 500 mm, insulation material: Steinwolle, insulation thickness: 150 mm, workpiece width (max.): 500 mm, Scope of delivery: 1. chemical pre-treatment by spraying (in cycle process) 2. dryer 3. powder coating system 4. single powder oven 5. conveyor technology, semi-automatic 6. electrical control system Hall/ floor space Floor area of the system max. 12,000 x 6,500 mm Hall floor Industrial floor Workpiece sizes Max. Part dimensions L= 500mm, H= 1,500mm, W= 500mm Range of steel parts Conveyor technology P&F chain conveyor in cycle mode, semi-automatic Bodpfx Asulwg Noduslr Pre-treatment Chemical Power supply Electricity On-site power (max. 88 kW) Gas On-site power Compressed air On-site power Water On-site power Calculation Type of system Cycle system Conveying speed 3.2 meters / min Length per cycle L = 1,600 mm Time for cycle movement: Tm = 1.6 meters : 3.2 meters/min = 0.5 minute Time for cycle standstill: Ts = 8.5-12 minutes Total time for cycle Tt = Tm + Ts = 9-12.5 min Electrical energy: Total power 88 kW min. Average consumption 60 kWh max. average consumption 70 kWh

Year of construction: 2020, condition: new, An automatic car wash is a solution that allows you to reduce costs, improve quality and increase the efficiency of the surface preparation process. The automatic car wash is equipped with a set of pumps for spraying, it has been designed so that as little liquid as possible migrates to subsequent processes after the process, saving money and improving the quality of washing. This is very important, because the apparent savings in systems made without the use of these solutions may generate much higher costs in the future related to chemicals and waste disposal, which will be simply more. Attention should also be paid to problems with maintaining the required bath parameters. Bedpfx Adjfz I Hxouslr Research and development works allowed us to develop a car wash with the function of drying details (Option) with hot air blown by a set of fans after the washing process. The car wash is equipped with an advanced system of creating own macro programs, which can consist of 10 steps each, depending on the number of tanks, the processes can be repeated, their order can be changed, etc. Each of the tanks has its own unique icon and name, enabling the operator to work intuitively. Optionally, the tanks can be equipped with bath replenishment systems, which can be carried out e.g. between processes or at the end of the cycle. • Controls installed on a swivel arm for better access • PLC microprocessor control • 7 "touch control panel • A very large number of nozzles compared to other solutions • (Option) Possibility of drying details after washing • Ability to create your own advanced programs • Advanced system of dampers made of acid-proof steel sheets, double secured with limit switches • Control system for tight closing and full opening of the flaps • To minimize fluid mixing, separate lines, nozzles, tanks for each treatment • Intelligent control - in the event of a power cut / sudden shutdown, the fluids cannot be mixed • Fully automatic operation

Year of construction: 2020, condition: new, Description Automatic sprinkling chamber is a solution that allows you to reduce costs, improve quality and increase the efficiency of the surface preparation process. The automatic sprinkling chamber is equipped with a set of spray pumps, it was designed so that as little liquid as possible after the process migrates to subsequent processes, thus saving money and improving the quality of washing. This is very important, because apparent savings in systems made without the use of these solutions can generate in the future much higher costs associated with chemistry and waste disposal which will simply be more. Attention should also be paid to problems with maintaining the required bath parameters. Research and development work allowed us to develop a sprinkling chamber with the function of drying details (option) with hot air blown by a set of fans after the washing process. The sprinkling chamber is equipped with an advanced system for creating your own macro programs, which can consist of 10 steps each, depending on the number of tanks, processes can be repeated, their order can be changed, etc. Each tank has its own unique icon and name, enabling the operator to work intuitively. Optionally, the tanks can be equipped with bath replenishment systems, which can be performed e.g. between processes or at the end of the cycle. • Control installed on the swivel arm for better access • PLC microprocessor control • 7 "touch operator panel • Very large number of nozzles, compared to other solutions • (Option) The possibility of drying details after the washing process • The ability to create your own advanced programs • Advanced damper system made of acid-resistant sheet metal, double protected by limit switches • Tight closing and full flap opening control system • To minimize fluid mixing, separate pipelines, nozzles, tanks for each treatment • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible • Fully automatic operation/ Prices are given in the catalog Bledpfx Aeflmdbeduor