Used Belflex Bf815 Scg-Tf for sale (1,357)

Condition: used, Year of construction: 2025, operating hours: 122 h, Operating hours: 122, First registration: 08.10.2025 Maximum lifting capacity: 3,000 kg Maximum lifting height: 6,700 mm Maximum outreach: 3,800 mm Length to attachment carrier: 4,510 mm Width: 2,000 mm Height: 2,120 mm Total weight with forks: 6,620 kg Total weight without forks: 6,450 kg Engine: 4-cylinder Deutz TCD 2.9 2.9 L displacement, water-cooled Power: 75 kW (101 hp) 2,600 rpm Stage V Diesel particulate filter, oxidation catalyst, and SCR catalyst with AdBlue injection (DPF + DOC + SCR) Hydrostatic drive Pump: electronically controlled with variable output Motor: variable displacement motor EPD PLUS including optional automatic rpm increase Mineral hydraulic oil HVI 46 Transmission: 2-speed Electrohydraulic control Vmax = 1st / 2nd gear = 16/20 km/h, optional 40 km/h Cab: Fully enclosed cabin, split door 360-degree all-round visibility GRAMMER air-suspended seat with safety lap belt ROPS/FOPS certified Heating Front, roof, and rear wipers Sunblind 4x1 joystick, electronic with capacitive release and travel direction switch Nwsdpfeyv S Ufox Aphjl Telescopic boom: 2-section with electronic end position cushioning (Soft Stop) Attachment carrier: Quick-change system type “ZM2” hydraulically controlled from the cab Steering: Hydraulic steering 3 steering modes: four-wheel, front-wheel, crab steering Drive: Permanent all-wheel drive Axles: Front axle rigid Rear axle oscillating Braking system: Servo-assisted disc brakes on all four wheels Automatic parking brake when engine is off Hydraulic system: Load-sensing pump with variable output Total flow: 100 l/min Working pressure: 250 bar Flow-sharing control block Electrics: 12V battery with 100 Ah Alternator 120A Stabilization control: Simplified Merlo ASCS system (ASCS-light) with fully electronic stability control, audiovisual signal, attachment recognition and overload cut-off Tyres: 400/70-20, agricultural tread Standard equipment: Power brake Hydraulic oil cooler Rear plate for mounting a trailer hitch Radio preparation Work lights on cabin (2 front, 2 rear) V2001 preparation for additional function at boom head 2 hydraulic connections at boom head Load guard on attachment carrier Road lighting Automatic battery disconnect switch Electrical connection cable inside boom Audible reverse warning Lift cylinder support for safety 1 Operating manual 1 Engine manual Special equipment: EU approval as tractor/towing vehicle 40 km/h incl. height-adjustable, self-locking trailer hitch, 30/32 mm pins, trailer lighting connection Air conditioning LED work lights on cabin (2 front, 2 rear) Boom suspension (B.S.S.) Location: 54595 Prüm

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, REF: MM6428 1 x PFM flow wrapper with peg and chain infeed conveyor and painted mobile frame.  Manufacturer - PFM Packaging Machinery S.p.A. Model - Swift.  Date of manufacture - 2011.  Electrical requirements - 230 V / 50 hz / 1 phase. Power - 14.5 Amps / 3.1 kW. Overall dimensions - 4150mm long x 950mm wide x 1950mm high. Nodpfxey Unmuj Aphjwl Adjustable folding box - up to 90mm wide.  Can wrap using clear or printed film. Supplied without the adapted infeed system, will be back to the standard infeed system. The PFM Swift is a horizontal flow-wrap machine with rotary crimp jaws, designed to wrap at speeds of up to 100 bags per minute. An extremely versatile, compact and reliable machine, the Swift will accomodate a wide range of products, with its standard adjustable forming box, providing the solution to quick and efficient size changes.

Condition: used, axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, first registration: 05/2015, suspension: air, tire size: 385/65R22.5, wheelbase: 9,110 mm, color: grey, Year of construction: 2015, Equipment: ABS, = Additional options and accessories = - Electronic Braking System (EBS) - Rear doors - Air suspension = Further information = Axle configuration Nwodozzwccopfx Aphsl Tire size: 385/65R22.5 Axle brand: SAF CD Brakes: Disc brakes Suspension: Air suspension Rear axle 1: Lift axle; Max. axle load: 9000 kg; Tire tread depth left: 50%; Tire tread depth right: 50% Rear axle 2: Max. axle load: 9000 kg; Tire tread depth left: 30%; Tire tread depth right: 30% Rear axle 3: Max. axle load: 9000 kg; Tire tread depth left: 40%; Tire tread depth right: 40% Weights Unladen weight: 7,560 kg Payload: 32,440 kg GVW: 40,000 kg Identification License plate: ON-35-TF Further information Please contact Bob Beukers for more information.

Condition: ready for operation (used), functionality: fully functional, power: 220.65 kW (300.00 HP), first registration: 05/2003, axle configuration: 4x2, color: red, Year of construction: 2003, Aerial Rescue Vehicle Rescue Platform / Work Platform Vema Lift Oy ​ Type: 323TFL-E Maximum Working Height: 32 meters Horizontal Outreach: approx. 21 meters Rotation Angle: 360° continuous ​ Maximum Basket Load: 400 kg Water Line to Basket Water Monitor in Basket Nwodpfx Apown Hwrshel Power Connection in Basket ​ Stabilizers: hydraulically operated, fully automatic Control: platform and ground controls (electrohydraulic) Special Features: Compliance certificate according to Machinery Directive 98/37/EEC, including EMC directive. Chassis Manufacturer: Scania Model: P94GB 4x2 NB Drivetrain: 4x2​ Transmission: Manual First Registration: 20/05/2003 Engine Power: 300 hp Additional Equipment Firefighting body with equipment compartment Hose reel and bracket Work lighting Surrounding area illumination Storage boxes for equipment Special Signal System Blue lights Sirene system (Martinshorn or equivalent) Condition & Service The vehicle has been stored exclusively in the fire department’s station and has undergone regular maintenance. Service and safety inspection were performed in April 2025. Complete vehicle and technical documentation is available. Additional Information The vehicle features additional firefighting-specific equipment and special functions. A detailed list of all equipment, technical specifications, and further documentation is available upon request. All information provided to the best of our knowledge and belief; no guarantee of completeness or accuracy. This advertisement does not constitute a binding offer, but is for informational purposes only. Subject to prior sale!

Condition: like new (used), functionality: fully functional, Year of construction: 2019, operating hours: 10,399 h, machine/vehicle number: 1897, sheet thickness steel (max.): 15 mm, sheet thickness stainless steel (max.): 15 mm, sheet thickness aluminum (max.): 12 mm, table length: 4,000 mm, table width: 2,000 mm, year of last overhaul: 2025, This 3-axis Bystronic BySprint Fiber 4020 4kW was manufactured in 2019. It offers a maximum sheet size of 4000 x 2000 mm and a powerful 4000-watt laser. If you are seeking high-quality fiber laser cutting capabilities, consider the Bystronic BySprint Fiber 4020 4kW machine. Contact us for more information. • Machine features a new cutting head (April 2026) • Max. sheet size: 4000 x 2000 mm Nwedpfxjy I Strj Aphjl Additional equipment • ByLoader (included)

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, turning length: 610 mm, turning diameter: 410 mm, spindle motor power: 18 W, spindle speed (min.): 30 rpm, spindle speed (max.): 3,500 rpm, spindle bore: 81 mm, travel distance X-axis: 265 mm, travel distance Z-axis: 680 mm, rapid traverse X-axis: 24 m/min, rapid traverse Z-axis: 30 m/min, type of input current: three-phase, total height: 1,700 mm, total length: 3,500 mm, total width: 1,700 mm, spindle nose: ASA 8, overall weight: 4,900 kg, swing diameter over top slide: 460 mm, spindle diameter: 255 mm, Equipment: documentation/manual, USED ​​3-axis lathe with driven tools and Fanuc 0i-TF CNC Nwedpfjzrnl Asx Aphol

Condition: new, Year of construction: 2025, machine/vehicle number: 1.2483.1, volume flow: 2,040 m³/h, total width: 835 mm, total length: 1,230 mm, total height: 2,000 mm, overall weight: 420 kg, input voltage: 400 V, ambient temperature (max.): 45 °C, ambient temperature (min.): 3 °C, type of cooling: air, pressure (max.): 16 bar, Energy saving refrigeration dryer KAESER TF 340 with energy-saving SECOTEC control. with electronically controlled condensate drain with controller SIGMA CONTROL SMART Year of construction: 2025 Technical data: Flow rate: 34 m³/min Pressure dew point: 3°C Nedjwvag Ajpfx Aphswl Overpressure: 3 to 16 bar Ambient temperature: +3°C to + 45°C Compressed air connection: DIN flange DN80 PN 16 Dimension (W x D x H): 835 x 1230 x 2000 mm Weight: 420 kg electrical supply: 400 V / 3 / 50 Hz Visit our store in Erlangen. You will find a large number of used and new compressors on over 450 square meters of exhibition space

Condition: used, axle configuration: 2 axles, total length: 157,000 mm, total width: 25,500 mm, Year of construction: 2008, Equipment: ABS, = Additional Options and Accessories = - EBS - Electronic Braking System - Air suspension, rear - Air suspension, front = Notes = For inquiries regarding the vehicle, please contact Mr. Seidel (at tel. ). Used EBERT forestry semi-trailer, low-bed trailer, type: TLS 36 ST, VIN: W0985180080D17001 self-supporting, with ECAS air suspension, fully hydraulically steered with remote control & ABS First registration: 03/2008, Permissible gross weight: 36,000 kg, Saddle load: 16,000 kg, Rear axle load: 20,000 kg, MOT: 01/2007, Low-bed length: 8,750 mm, Length: 15,700 mm, Width: 2,550 mm, Payload approx.: 27,000 kg The forestry machine is transported at a height of approx. 10-25 cm above the road surface. Tires: 235/75R/17.5 low-profile, tubeless. Tire tread: 1st axle 9-12 mm, 2nd axle 7-11 mm Axles: 2 x 10 tons Nwsdpfez Engkex Aphel Axles with S-cam brakes and ABS, hydraulically actuated two-circuit forced steering controlled from the kingpin. Saddle plate with 2-inch kingpin and drive-away wedge. 24V electric generator with HD piston pump, oil tank and 2 batteries enable remotely controlled functions via wireless remote control. Brakes: Two-line brake system according to EC with spring-loaded brake cylinders acting on the rear axles. With ABS Lighting according to StVZO (German Road Traffic Licensing Regulations). Integrated into a recessed underrun protection, incl. license plate holder. Also, warning lights in the pull-out marker panels for overwidth transport. The hydraulic forced steering is equipped with a wireless remote control as standard, so the driver can "steer" from the cab in tight hairpin turns and during turning maneuvers. Options included in the price: a. Yellow rotating beacon at the rear, pluggable b. with 4 pull-out marker panels (red/white) with a retracted width of 2,550 mm and an extended width of 2,750 mm or 3,000 mm. c. with electro-hydraulically operated ramps Upon request, we will provide you with a leasing or financing offer. Mr. Seidel (tel. ) will be happy to assist you. Further information can be found on our website. ... Errors, changes and prior sale reserved !!! - Steering axle = Further information = Unladen weight: 9,000 kg Payload: 27,000 kg GVW: 36,000 kg Last inspection: 2027-01 Please contact Tobias Ebert for further information.

Condition: ready for operation (used), Year of construction: 2019, operating hours: 21,000 h, clamping force: 1,270 kN, total width: 1,500 mm, total height: 1,700 mm, overall weight: 5,300 kg, product length (max.): 5,100 mm, This 3-axis SHIBAURA EC130SXIII-4A was manufactured in 2019. It features a clamping force of 1270 kN and a mold opening stroke of 400 mm. The machine has a maximum distance between platens of 950 mm and platen dimensions of 720 x 670 mm. If you are looking to get high-quality injection molding capabilities, consider the SHIBAURA EC130SXIII-4A electrical injection moulding machine we have for sale. Contact us for further details. • Distance between tie bars (H x V): 510 x 460 mm • Platen dimensions (H x V): 720 x 670 mm • Mold opening stroke: 400 mm Nwsdpfx Asy Iffnsphsl • Max. distance between platens: 950 mm • Mold height (min–max): 180–550 mm • Ejection force: 30 kN (3.0 tf) • Ejection stroke: 90 mm • Injection unit code: 14 • Nozzle touch force: 17.7 kN (1.8 tf) • Injection speed (standard): 300 mm/s • Injection speed (high torque): 200 mm/s • Injection speed (high speed): 400 mm/s • Main breaker capacity (standard/high torque): 100 A • Main breaker capacity (high speed): 125 A • Transformer (standard): 75 kVA

Condition: used, Year of construction: 2021, Citizen Miyano BNJ-51SY6 5 Axis Fixed Headstock Lathe with Fanuc Oi-TF Control, Serial No. DV8166 (2021), Twin Spindle Collet Chucks, Twin Turret, Main Turret 12 Position all Driven, Secondary Turret 8 Position 4 Driven, Main Spindle 50 - 5000rpm, Sub Spindle 50 - 5000rpm, Parts Catcher, Cromar Combi 500 Swarf Conveyor, Imeca Boss 545-E 5 Meter Barfeed, Serial No. 020529GA01. 5,800kg. (2) x Boxes of Driven & Static Tooling for BNJ 51. Country of Origin: Philippines Nwjdozzb Rdspfx Aphol Location: These lots are located in Biggleswade, UK. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser.

Condition: used, Year of construction: 2021, Citizen Miyano BNJ-51SY6 Fixed Headstock Lathe 5 Axis Machine with Fanuc Series Oi - TF CNC Control, Twin Spindle Collet Chucks, Twin Turret, Main Turret 12 Position All Driven, Secondary Turret 8 Position, 4 Driven, Max Spindle 50 - 5000rpm, Sub Spindle 50 - 5000rpm, Max Work Piece Diameter 51mm, Parts Catcher, Cromar Combi 500 Swarf Conveyor. Serial No. DV8125 (2021), Imeca Boss 551E 5 Meter Barfeed, Serial No. 020829GA03. 6200kg. (1) x Box of Driven Tooling for BNJ 51. Country of Origin: Philippines Nsdpfezzb Hfsx Aphowl Location: These lots are located in Biggleswade, UK. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser.

Condition: used, Year of construction: 2009, functionality: fully functional, machine/vehicle number: 9A5822, type of input current: three-phase, input voltage: 400 V, input current: 60 A, total height: 1,800 mm, cutting width (max.): 1,720 mm, cutting height (max.): 50 mm, compressed air connection: 6 bar, For sale is a Lectra Vectorfashion VT-FA-MH-71 automated CNC textile cutting system, offered as a complete industrial production line. This system is designed for high-volume, high-precision fabric cutting in garment manufacturing. It enables automated multi-layer cutting with consistent accuracy and significantly improves production efficiency compared to manual cutting processes. The machine has been operated as part of a dedicated and independent cutting line together with a GERBER SY 101 spreading system (unit 21 C) and a Gerber automatic fabric loader (unit 31 C). Nwjdpfxoy Avg Eo Aphol This configuration enables a fully synchronized workflow from roll loading to spreading and cutting, maximizing throughput and minimizing manual intervention. The system includes a long-format vacuum cutting table, gantry-mounted cutting head, and integrated extraction system. A computer-controlled interface ensures precise execution of cutting patterns and production workflows. The unit has been used in a professional garment factory and was operational prior to factory shutdown. Recently serviced on 27.02.2026. Video recorded in operation on 05.03.2026. Includes • Lectra Vector CNC cutting system • Gantry-mounted cutting head • Conveyorized cutting surface • Industrial vacuum system (approx. 30 kW class) • Dust extraction system • Computer workstation and control interface Technical Details • Manufacturer: Lectra, France • Model: VT-FA-MH-71 • Serial number: 9A5822 • Year: 2009 • Type: Automated CNC textile cutting system • Control: Computer-controlled (Lectra software environment) • Cutting method: Oscillating knife, multi-layer capable • System: Vacuum hold-down with extraction Electrical & Utility Requirements • Control cabinet: approx. 230 V, single phase • Vacuum system: approx. 400 V, 3-phase, up to 30 kW • Peak current (startup): up to approx. 60 A • Compressed air: 5–7 bar, dry and filtered • Air consumption: required for tool operation and cooling Cutting Performance • Multi-layer cutting capability (approx. 25–70 mm compressed lay height depending on material) • High acceleration and cutting speed for reduced cycle time • Repeatable precision across full table width • Continuous feeding capability for long production runs System Architecture • Gantry-driven X/Y cutting head for high-speed positioning • Vacuum table with bristle block surface for material stabilization • Conveyorized system enabling continuous material feed • Integrated extraction system for dust and fiber removal Production Advantages • Significant material savings through optimized nesting and precise cutting • Reduced labor costs compared to manual cutting processes • High throughput suitable for industrial-scale production Service & Condition Notes • Recently serviced on 27.02.2026 • Video available from operation (05.03.2026) • Machine was operational prior to factory shutdown • Typical wear consistent with industrial use • Software compatibility should be verified if upgrading control workstation Condition Used industrial condition Operational prior to shutdown Sold as-is, where-is, without warranty Typical Applications • Garment production cutting rooms • Workwear and denim production • Technical textile cutting • Upholstery and automotive textiles Location Valga, Estonia Removal & Transport Buyer responsible for dismantling, loading, and transport Professional dismantling required due to system size and complexity

Condition: like new (used), Year of construction: 2023, Nock TFE 350A Freeze Drum Fish Skinner Nedpfez A Tvlex Aphewl The NOCK Freeze Drum Skinner TFE 350A is a fish skinning machine that utilizes freeze drum technology. It combines NOCK’s extensive experience in fish skinning with its expertise in refrigeration technology, drawing on the knowledge gained from the construction of NOCK’s industrial ice machines. This results in fish skinning machines with reliable German engineering, high quality, high energy efficiency, easy cleaning, and a compact design. Furthermore, the service-friendly design ensures low maintenance costs. Manufacturer: Nock Model: TFE 350A Year: 2023 Cutting width: 370 mm Conveyor belt width: 350 mm Cutting speed: 8-20 m/min Max. product height: 40 mm Skinning depth: 0.1 – 10 mm, stepless adjustment Freeze drum diameter: 450 mm Refrigerant: R449A Power: 400 V / 50 Hz / 5.5 kW Machine dimensions (LxWxH): 2,600 x 1,550 x 1,500 mm Machine weight: 800 kg.

Condition: ready for operation (used), Year of construction: 2017, operating hours: 18,955 h, spindle speed (max.): 4,500 rpm, travel distance X-axis: 203 mm, travel distance Y-axis: 82 mm, travel distance Z-axis: 585 mm, spindle motor power: 15,000 W, total height: 1,852 mm, total width: 1,935 mm, overall weight: 6,000 kg, bar diameter (max.): 65 mm, controller manufacturer: FANUC, controller model: 0i-TF, product length (max.): 2,716 mm, number of slots in tool magazine: 12, number of axes: 4, This 4-axis NAKAMURA-TOME AS-200L was manufactured in 2017. It features a maximum turning diameter of 320 mm and a turning length of 570 mm. The machine includes a 12-station turret and a main spindle speed of up to 4500 rpm. If you are looking to get high-quality turning capabilities, consider the NAKAMURA-TOME AS-200L horizontal turning machine we have for sale. Contact us for further details. Standard Equipment • Turret: 12-station drum turret • CNC control, 4 axes (including C-axis), Fanuc 0i-TF • Anti-collision protection system (mechanical “Airbag”) • Y-axis • 15″ LCD monitor with USB port • Live tooling – 12 positions • Automatic central lubrication system • Machine working area lighting • Coolant pump – 180 W • Initial coolant filling (Blaser coolant)Options included • Transformer • Luck-Beil II (NT Manual Guide – graphical interface for control) • Increased spindle bore to 71 mm (4500 rpm; A2-6) • Upgraded main spindle motor Fanuc 15 / 11 kW (258 Nm) • High-pressure coolant system with Brinkmann pump • Shut-off valve for high-pressure coolant system • Low coolant level sensor • Part ejector cylinder from sub-spindle (cylinder stroke 100 mm) • Signal tower for machine status (3 colors) • Operator shelf under control panel • Type A parts catcher (Ø71 mm / L150 mm / 3 kg) • Preparation for LNS bar feeder • Air blow through main and sub spindle • Manual tool probe (Renishaw, one arm for both spindles) • Spindle cooling system for main and sub spindle • Preparation for oil mist extraction system • There are no tools or tool holders included in the offer Nedpjytqpnjfx Aphewl Technical Specification Counter Spindle Yes Driven Tools Yes

Year of construction: 2009, condition: used, For sale are 8 free-flow centrifugal pumps from Pumpenfabrik Wangen, manufactured in 2009. These are the ESP model. Five of the eight free-flow centrifugal pumps have a motor. Quantity: 5 / 3 with motor Length: 172cm (without motor) / 229cm (with motor) Height: 34cm Manufacturer: Pumpenfabrik Wangen Type: ESP No.: 920607 Year of manufacture: 2009 Connections: DN100 PN16 Nwodpfx Aega Dtcephjl Motor: SEW Eurodrive Type: RF77DV100L4/TF No.: 01.1280626601.0003.09 rpm: 1400/48 kW: 3/S1 V: 230/400 A: 11 / 6.30

Condition: good (used), Year of construction: 1978, functionality: fully functional, For sale is a robust Hofmann table milling machine, built in 1978, in a heavy-duty industrial design. The machine is equipped with a Holz-Her 3-roller feed unit ETZ and is suitable for a variety of milling operations in carpentry workshops, joineries, and in the furniture and interior design industries. The height adjustment of the milling spindle is conveniently done via a handwheel. The milling jaws can be adjusted manually. Three different spindle speeds allow for adaptation to various milling operations. In addition, the machine is equipped with 3 Aigner rails. Technical data Manufacturer: Hofmann Year of construction: 1978 Milling spindle diameter: 30 mm Spindle speeds: 6,000 / 8,000 / 10,000 rpm Height adjustment: by means of a handwheel Milling jaw adjustment: manual Dust extraction connections: Ø 120 / 140 mm Machine size: approx. 2,700 x 1,100 mm Heavy-duty table and machine construction made of cast iron Equipment Nwodpfxjzvdk Ao Aphjl Holz-Her 3-roller feed unit ETZ 3 feed rollers Height-adjustable feed unit Manual milling fence 3 Aigner rails Milling spindle Ø 30 mm 3 spindle speeds Handwheel for height adjustment Dust extraction connections Accessories as shown in the photos Scope of supply Hofmann table milling machine Holz-Her 3-roller feed unit ETZ 3 Aigner rails Accessories as shown in the photos The machine can be inspected and tested under power by appointment. Transport possible for an extra charge! The machine is subject to differential taxation according to § 25a UStG. The machine will be inspected before sale. For used machines with a year of construction of 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sale and changes are subject to change. All information without guarantee.

Condition: ready for operation (used), SEW-Eurodrive KHF67 DR80M4BE1/TF motor SN 01.7173972303.0001.14,used, minor signs of wear, 100% functional, scope of delivery as per photos Nodeqm Sqpspfx Aphswl

Condition: ready for operation (used), SEW-Eurodrive KHF67 DRS80S4BE1/TF Motor SN 01.1756001307.0001.11,used, minor signs of wear, 100% functional, scope of delivery as per photos Nedpoqm Sqtsfx Aphowl

Condition: used, Year of construction: 2019, operating hours: 7,551 h, Rigid telescopic forklift Mast type: None Nwjdpfxjyfi Imj Aphjl

Year of construction: 2023, condition: ready for operation (used), - USED - 3-AXIS CNC LATHE DISTANCE BETWEEN CENTRES: 640 mm MAX ROTATING DIAMETER: 600 mm MAX TURNING DIAMETER: 420 mm BAR CAPACITY: 75 mm SPINDLE: 3500 rpm; 15-18,5 kW; ASA A2-8 ; 254 mm X-AXIS TRAVEL: 210+30 mm Z-AXIS TRAVEL: 610 mm RAPID FEEDS X-Z: 18 - 24 m/min DRIVEN TURRET HEAD: BMT65 ; 12 POS; 4000 rpm; 4,5 kW CONTROL UNIT: FANUC 0i-TF WEIGHT: 6230 Kg OVERALL DIMENSIONS: 4017 x 1848 x 1819 mm ACCESSORIES: SWARF CONVEYOR ; FANUC MANUAL GUIDE-I ; ETHERNET PORT ; USB PORT NOTE: WITH No 7 FIXED TOOL HOLDERS; RENISHAW MANUAL TOOL SETTER Nwedpfx Aoyy D I Ejphjl

Condition: good (used), spindle moulder, spindle moulder -Manufacturer: Metabo, swivel table milling machine type Tf 1690 D with support table Nsdpewha Nbofx Aphswl -Drive: 2.0 kW -Milling spindle: Ø 30 mm -Speeds: 3,000 / 6,250 / 9,000 rpm -Cutter: Ø max. 200 mm -Table length: 3600 x 500 mm -Dimensions: 3600/910/H1610 mm -Total weight: 170 kg

Condition: used, power: 100 kW (135.96 HP), Year of construction: 2023, operating hours: 219 h, maximum speed: 40 km/h, Operating hours: 219, First registration: 16.01.2024 _____ Max. load capacity: 4,200 kg Max. lift height: 7,000 mm Max. outreach: 3,800 mm Length to attachment carrier: 4,730 mm Width: 2,310 mm Height: 2,530 mm / 2,590 mm (with CS activated) Total weight with forks: 8,170 kg Total weight without forks: 8,000 kg Engine: 4-cylinder Perkins 904J 3.6 l displacement, water-cooled Output: 100 kW (136 HP) 2,300 rpm Hydraulic reversing fan Emission Stage V Diesel particulate filter, oxidation catalyst, and SCR catalyst with AdBlue injection (DPF + DOC + SCR) Hydrostatic drive Pump: electronically controlled with variable output Motor: variable displacement EPD PLUS incl., with optional automatic rpm increase Mineral-based hydraulic oil HVI 46 Transmission: 2 speeds, electrohydraulically controlled Vmax = 1st / 2nd gear = 16 / 20 km/h, optional 40 km/h Cab: closed cab, split door, 360-degree all-round visibility GRAMMER air-suspended seat with safety lap belt ROPS/FOPS certified Heating Front, roof, and rear wipers Sunblind 4x1 electronic joystick with capacitive enable incl. direction selector switch CS = hydropneumatic cab suspension Telescopic boom: 2-section with electronic end-position dampening (Soft Stop) Quick-attach device carrier Type "ZM2" hydraulically controlled from cab Steering: hydraulic steering, 3 steering modes: all-wheel, front-wheel, crab steer Permanent all-wheel drive Axles: fixed front axle, oscillating rear axle Brake system: servo-assisted disc brakes on all four drive shafts, automatic parking brake when engine is off Frame: high-strength steel design Hydraulic system: variable displacement pump "LOAD SENSING" Working hydraulics flow: 151 l/min Hydraulic fan flow: 46 l/min Total flow rate: 197 l/min Working pressure: 250 bar Flow-sharing control block Electrics: 12 V, 100 Ah battery, 120 A alternator Stabilization control: simplified Merlo ASCS system (ASCS-light) with fully electronic stability control, audiovisual signal, implement detection, and overload shutoff Tires: 460/70 R 24 Standard equipment: servo brake, hydraulic oil cooler, rear mounting plate for tow bar, hydraulic reversing fan, radio prep, work lights on cab (2 front, 2 rear), preinstalled function for auxiliary hydraulics at boom head, 2 hydraulic connections at boom head, load protection guard on attachment carrier, road lighting, automatic main battery disconnect, electrical cable in boom, acoustic reverse signal, lift cylinder support for safety Special equipment: EU homologation as tractor/ towing vehicle 40 km/h incl. self-locking trailer coupling, 30/32 mm pin, incl. trailer lighting connector Air conditioning Boom suspension (B.S.S.) LED work lights on cab (2 front, 2 rear) 2 work lights at the end of the first boom section (base boom) ASCS upgrade: monitor with all ASCS functions + thumb... Nwedpfx Aepcht Hsphol

Condition: excellent (used), functionality: fully functional, machine/vehicle number: FN524110, Year of construction: 2016, operating hours: 10,204 h, load capacity: 2,000 kg, lifting height: 4,400 mm, free lift: 1,435 mm, load center: 500 mm, fuel type: gas, mast type: triplex, construction height: 2,020 mm, gearing type: hydrostat, fork length: 1,000 mm, front tire type: cushion tires (black), overall weight: 3,282 kg, empty load weight: 3,282 kg, total height: 2,020 mm, color: yellow, Equipment: CE marking, UVV, lighting, pallet forks, sideshift, Price: €10,000 net €11,900 gross SKU: 442 Basic information: - Manufacturer: Jungheinrich - Model: TFG 320s - Year of manufacture: 2016 - Operating hours: 10204h Technical data: - Drive: LPG - Transmission: Hydrostatic - Pedals: Single pedal control - Control: Solopilot - Battery: - Charger: Mast / Dimensions: - Overall height: 2020 mm - Lifting height: 4400 mm - Free lift: 1435 mm - Mast type: Triplex mast - Fork length: 1000 mm - Rated load capacity: 2000 kg - Load center: 500 mm Tires: - Type: Superelastic tires (SE) Hydraulic equipment: - Side shifter: Integrated - Fork positioner: No - Rotating device: No - Additional hydraulics: No. 1 and 2 available and in use Equipment: - Body: Load protection cage with roof panel - Lighting: 2x front, 2x rear - Safety equipment: Seat belt, spotlight at the rear - Heater: No Extras: - UVV inspection can be carried out upon request - Immediately ready for use - Inspection and test drive possible on site by appointment. Transport: Cost-effective shipping possible upon request. Invoice with VAT: You will always receive an invoice with VAT shown. Battery: For battery-powered equipment, we will gladly provide a quote including a new battery. Contact: If you have any questions or are interested, please contact us by phone, email, or contact form. Nwodpfxozl Tcme Aphjl Subject to prior sale.

Condition: used, Year of construction: 2008, operating hours: 12,310 h, functionality: fully functional, machine/vehicle number: 50998, grinding length: 1,000 mm, grinding width: 600 mm, total height: 400 mm, total length: 1,200 mm, feed length X-axis: 1,200 mm, workpiece weight (max.): 500 kg, grinding wheel diameter: 400 mm, table length: 1,000 mm, table load: 600 kg, table width: 600 mm, grinding wheel width: 130 mm, spindle speed (max.): 3,200 rpm, spindle speed (min.): 50 rpm, overall weight: 6,400 kg, table height: 100 mm, grinding spindle motor power: 32 W, rotational speed (max.): 3,200 rpm, rotational speed (min.): 50 rpm, power: 48 kW (65.26 HP), input voltage: 400 V, disc diameter: 400 mm, Equipment: documentation/manual, rotational speed infinitely variable, ELB- Perfekt-Future BD 10 CNC Nwedox Th S Uopfx Aphjl Machine in excellent condition, fully functional, for sale only due to lack of space and overcapacity.

Condition: good (used), axle configuration: 2 axles, permissible axle load (axle 2): 10,000 kg, first registration: 09/2009, total length: 11,500 mm, total width: 2,600 mm, tire size: 275/70R22.5, wheelbase: 7,500 mm, color: white, Year of construction: 2009, Equipment: tail-lift, = Additional Options and Accessories = - Refrigeration/Freezer Unit - Air Suspension = Notes = Pacton refrigerated semi-trailer with single axle 1999 Maxima Carrier refrigeration unit 1300 7039 operating hours* Unit manufactured in 2004 Nodpfx Apjzmg Ryshjwl with Mariba loading platform Spare wheel holder + spare wheel Toolbox = Further Information = Axle Configuration Front Axle: Tire size: 275/70R22.5; Double tires; Steerable; Tire tread depth left inside: 40%; Tire tread depth left outside: 40%; Tire tread depth right inside: 40%; Tire tread depth right outside: 40% Maximum Rear Axle Load: 10,000 kg Weights Unladen weight: 8,530 kg Payload: 13,470 kg GVW: 21,999 kg Functional Body brand: carrier Refrigeration engine: Diesel and electric (7040 operating hours, diesel) Condition Technical condition: good Optical condition: good Warranty Warranty: Pacton refrigerated semi-trailer with single axle 1999 Maxima Carrier refrigeration unit 1300 7039 operating hours* Unit manufactured in 2004 with Mariba loading platform Spare wheel holder + spare wheel Toolbox Identification License plate: OK-58-XV Further Information Please contact VAEX The Truck Traders for further information.