Used Gesan Dps 65 for sale (7,693)

Year of construction: 2013, operating hours: 7,700 h, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 12090, This is a recycling extruder with side feeding for materials (flakes, pellets, etc.). The system is supplied with a control cabinet and a double vacuum system. The pelletizing system is missing at the end of the screw – it is not included in the scope of supply. The cylinder ends at the flange. The extruder is supplied without a screw. The frequency inverter for the main motor was replaced with a new unit 3 years ago. Installed power approx.: 474 kW Cooling water requirement approx.: 190 l/min Fresh water consumption approx.: 110 l/h Feeding system: • Diameter of the feeding screw: 200 mm • Drive for the feeding screw: 45 kW, frequency-controlled • Hopper capacity net 7 m³/250 ft³, • Gear motor 3 × 3 kW • 2 sight glasses in the hopper • 2 level indicators Extruder: • Diameter of the extruder screw: 145 mm • L/D ratio: 24 • Heating power: 50 kW • Extruder drive unit 280 kW Vacuum 1: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 11 kW • Vacuum capacity: 225 m³/h • Vacuum pressure: 33 mbar Vacuum 2: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 7.5 kW • Vacuum capacity: 190 m³/h • Vacuum pressure: 33 mbar Cylinder: • Cylinder: Bimetal extruder cylinder, • Reinforcement layer 1.8–2.0 mm thick, • Hardness 63–65 HRC Installation conditions: • Voltage: 3 × 400 Volts • Permissible fluctuation max.: +5 % – 5 % • Frequency: 50 Hz Permissible fluctuation max.: +4 % – 4 % • Protective measure: Multiple grounding • Ambient temperature: min. 15 °C, max. 35 °C • Humidity max.: 90 % • Altitude of the installation site: 0 – 1000 m The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center is being closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price is without packaging. Isdpjznz Ezefx Aidoif

Condition: like new (used), Year of construction: 2023, functionality: fully functional, Factory new – never installed! Weinig Hydromat 4300, high speed planer and moulder Feed speed 30-300 m/min Spindle 1 (Bottom) – Radial CNC-controlled adjustment – Hydro bearing with automatic locking – Straight jointer, fully automatic Spindle 2 (Top): – Radial and axial CNC-controlled adjustment – Hydro bearing with automatic locking – Straight jointer, fully automatic Spindle 3 (Right): – Radial and axial CNC-controlled adjustment – Straight jointer, fully automatic Spindle 4 (Left): – Radial and axial CNC-controlled adjustment – Straight jointer, fully automatic Spindle 5 (Top): – Radial and axial CNC-controlled adjustment – Hydro bearing with automatic locking Ijdezu Awropfx Aidoif – Straight jointer + profile jointer fully automatic Spindle 6 (Bottom): – Table tops with wood inserts, maximum cutting height of 65 mm with a flange of 100 mm – Rotaplan pressure plate above the bottom shaft – Radial and axial CNC-controlled adjustment – Straight jointer, fully automatic – Hydro bearing with automatic locking General: – Horizontal CNC-controlled pressure rollers – CNC-controlled positioning input – Marathon Powercoating Plus – Automatic waxilit pump – Weinig WMC with touchscreen – Kickback protection for sawing operations – Machine with spindle and feed brakes – Safety and sound insulation housing

Condition: used, axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, first registration: 02/2010, total length: 14,000 mm, total width: 2,600 mm, suspension: air, tire size: 385/65 R 22.5, wheelbase: 9,150 mm, color: white, Year of construction: 2010, Equipment: ABS, tail-lift, = Additional options and accessories = - Rear doors - Lift axle - Air suspension - Fog lights - Side skirts = Further information = Axle configuration Tire size: 385/65 R 22.5 Axle brand: BPW Brakes: Disc brakes Suspension: Air suspension Rear axle 1: Lift axle; Max. axle load: 9000 kg Rear axle 2: Max. axle load: 9000 kg Rear axle 3: Max. axle load: 9000 kg; Steerable Weights Unladen weight: 10,520 kg Payload: 30,480 kg GVW: 41,000 kg Functional Body brand: CARRIER VECTOR 1850 Refrigeration engine: Diesel and electric Iiedpfx Aiszvgmaedjf Identification License plate: OK-72-YP

Condition: used, Empty weight: 12.500 kg Length: 62 cm Serial number: B151706 Machining center consisting of: - a NAKAMURA TOME CNC lathe, model: SUPER NTJ, manufactured in 2007 - a SAMSYS+ bar feeder, model: M3000 Isdpfx Aozvccqjidsif - a FANUC 18i-TB controller - Technical specifications: - Number of controlled axes: 9 axes - Number of simultaneously controlled axes: 4 - Maximum turning diameter: 190 mm - Maximum turning length: 620 mm - Bar capacity: 51 mm (R/L)/ 65 mm (Left) - Chuck: 210 mm - Spindle speed: 5,000 rpm (∅51)/ 4,500 rpm (∅65 mm) - Spindle nose: A2-5 (∅51) / A2-6 (∅65) - Spindle bore: 63 mm (∅51) / 80 mm (∅65) - C-axis: 0.001° - 600 rpm - B-axis: -91° to +91° - 180°/s - 2 turrets: 24 stations - 12 powered tools - Powered tool speed: 60 to 6,000 rpm - X1 travel: 345 mm - X2 travel: 167.5 mm - Z1 travel: 1,240 mm - Z2 travel: 685 mm - Y-axis travel: 45 mm - Feed rate: X1/X2 16 m/min - Z1/Z2 40 m/min - Machine weight: 12,500 kg - Approximate dimensions: L 3,660 mm x W 2,320 mm x H 2,170 mm Hours on the counter: approximately 2,960 hours of use Online auction held following the closure of the "Supadis" production facility in Le Plessis-Pâté (91), a company specializing in precision machining. This sale includes more than 100 lots, notably several 3-, 4-, and 5-axis CNC machining centers from “Matsuura,” “OKK,” “Biglia,” and “Nakamura Tome,” as well as a “Kasto Functional A” automatic saw. The lot also includes grinding machines, a “Cincinnati” column drill press, “Trimos” and “Mitutoyo” measuring columns, as well as numerous tools, workbenches, and inspection equipment. The sale also includes stocks of raw materials (steel, aluminum, titanium, “Inconel,” “PEEK,” copper, etc.), workshop equipment, compressors, shelving, and various material-handling equipment. Sale organized by Dome Auctions France, OVV No. 331-2026, auctioneer Blandine Camper. The online auction opens Tuesday 18 August and closes Thursday 24 September. Register your account via our website and place your bid. For viewings and inspections check the auction information on the website. Viewing day is on: - Tuesday 22 September Dome Auctions is an innovative auction platform dedicated exclusively to the industrial sector. By focusing on machinery sales from business closures, restructurings, and bankruptcies, we provide a trusted marketplace where buyers and sellers connect with confidence. Unlike general auction houses, Dome Auctions specializes in selling complete industrial assets directly from factories, ensuring quality and reliability. With a commitment to transparency, industry expertise, and tailored service, we streamline the sales process and maximize value for all parties. As online auctions continue to grow in the European industrial market, Dome Auctions offers a professional and...

Condition: used, axle configuration: 3 axles, first registration: 12/2008, suspension: air, tire size: 385/65, tire condition: 40 %, color: other, Year of construction: 2008, Equipment: ABS, = Additional options and accessories = Iijdpfszvduzsx Aidjf - ADR - Air Suspension - BPW Axles - Disc brakes = More information = Tyre size: 385/65 Make axles: BPW Tyre profile: 40% Brakes: disc brakes Suspension: air suspension Empty weight: 3.500 kg Carrying capacity: 34.500 kg GVW: 38.000 kg

Condition: used, axle configuration: 3 axles, first registration: 05/1997, total length: 10,550 mm, total width: 2,550 mm, suspension: air, tire size: 385/65, tire condition: 30 %, wheelbase: 7,550 mm, color: other, Year of construction: 1997, Equipment: ABS, = Additional options and accessories = - Air Suspension - Lift Axle Ijdpfxozvat Hs Aidjif = More information = Axle configuration Make axles: BPW Brakes: drum brakes Suspension: air suspension Rear axle 1: Tyre size: 385/65; Lift axle; Tyre profile: 30% Rear axle 2: Tyre size: 385/65 R20; Tyre profile: 30% Rear axle 3: Tyre size: 385/65; Tyre profile: 50% Weights Empty weight: 6.660 kg Carrying capacity: 30.340 kg GVW: 37.000 kg Functional Tipper: Back Identification Registration number: OS-94-GH

Condition: used, axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, first registration: 01/2015, loading space length: 13,410 mm, loading space width: 2,510 mm, loading space height: 2,650 mm, total length: 14,040 mm, total width: 2,600 mm, suspension: air, tire size: 385/65, tire condition: 30 %, wheelbase: 8,770 mm, color: other, Year of construction: 2015, Equipment: ABS, tail-lift, = Additional options and accessories = - Air Suspension - BPW Axles - Disc brakes - Lift Axle - Tailgate = More information = Axle configuration Tyre size: 385/65 Iiodpjzvd Hdefx Aidsf Make axles: BPW Brakes: disc brakes Suspension: air suspension Rear axle 1: Lift axle; Max. axle load: 9000 kg; Tyre profile: 30% Rear axle 2: Max. axle load: 9000 kg; Tyre profile: 40% Rear axle 3: Max. axle load: 9000 kg; Tyre profile: 30% Weights Empty weight: 8.255 kg Carrying capacity: 32.745 kg GVW: 41.000 kg Functional Cooling engine: diesel and electric (8030 operating hours diesel; 297 electric) Maintenance APK (MOT): tested until 01/2027 Identification Registration number: ON-37-NP

Condition: used, Year of construction: 2019, operating hours: 4,300 h, Equipment: all wheel drive, * Wacker Neuson EW 65 wheeled excavator * Year of manufacture: 2019 * 4300 operating hours * 7290 kg * 45.5 kW Perkins engine * 30 km/h Iijdpfeyq A H Tjx Aidof * Hydraulic Powertilt quick coupler * 3 buckets: 125, 60, 40 cm * All hydraulic lines * Air conditioning * Central lubrication * Camera * Particulate filter * Track width approx.: 208 cm

Condition: refurbished (used), Year of construction: 2017, machine/vehicle number: R-00630, load capacity: 165 kg, arm reach: 2,655 mm, controller manufacturer: R-30iB A-Size, teach pendant manufacturer: A05B-2255-C101#EGN, Refurbished FANUC R-2000iC/165F manufactured in 2017.01. The robot comes with an R-30iB A-Size controller including iPendant.   Our experts extensively tested the robot, after which we conducted a maintenance service according to the manufacturers’ specifications. The grease is examined for the amount of iron particles, indicating the corresponding axes' condition. Only robots in excellent mechanical condition will be completely refurbished, ensuring a long-term solution for our customers. This enables us to deliver our robots with a warranty term of 12 months as standard!   Iisdpfx Aiezu Tznedjf Brand: FANUC  Model: R-2000iC/165F Model Number: A05B-1333-B201 Year of Manufacture Robot: 2017.01 Warranty term (months): 12   Payload (kg): 165 Reach (mm): 2655 Repeatability (mm): ± 0.05 Controlled Axes: 6-axis Installation Type: Floor Mount Weight (kg): 1090   Controller: R-30iB A-Size Year of Manufacture Cabinet: 2016.12 RCC Length (m): 14   Teach Pendant: A05B-2255-C101#EGN Teach Pendant Cable Length (m): 10

Condition: good (used), Fan, blower, fan wheel, cross-flow fan, cross-flow blower, cross-flow ventilator, roller fan -Manufacturer: Indramat, fan, blower, crossflow fan -Type: QLN 65/012 A3-3038L33 tg -Voltage: 220/230 V -Number: 2 fans included Iijdpfoztvpxex Aidof -Price: per piece -Dimensions: 240/155/H105 mm -Weight: 1.9 kg/pc.

Condition: ready for operation (used), Year of construction: 2013, Brand: HSM Type: V-Press 1160 plus Year of manufacture: 2013 Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Isdozuxqhopfx Aidoif Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feed opening dimensions: 119.5 cm x 65 cm The HSM 1160 V-Press features simple operation, a powerful pressing force, and is energy-efficient. Are you looking for a more compact model? Then take a look at the HSM 860 – ideal for those who want to save space without sacrificing pressing power.

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Equipment: documentation/manual, type plate available, PRICE REDUCED AGAIN!!!!! Taylor Hobson Talyrond 265 roundness measuring system. Extremely accurate; it can measure the roundness of lenses, optics, pistons, turbine components, tubes, shafts, and also eccentricity, e.g., of cams on a camshaft or journals of a crankshaft. This would certainly be of interest to motorsport and tuning companies. The first photo is a "representative image" from a Taylor Hobson catalog, showing how it is set up, except for the computer, which is a newer, smaller-form-factor HP model. Iijdpozcqy Eefx Aidef Max. diameter: 350mm Max. test piece height: 500mm (higher measurements are possible, up to a maximum of 1000mm when measured in two halves...) Self-centering of the workpiece: +/- 5mm Max. weight of test piece: 40 kg The system has been used very little and has had only two owners. The first owner, from whom I purchased it, was an implant company in Hamburg. It was used in a "medically clean environment" and is extremely clean. It was never located in a dirty machine hall. The year of manufacture is estimated to be between 2002 and 2005. The Taylor-Hobson measuring software is, of course, included and runs on the supplied HP computer (without a password...). Accessories are included: the original Taylor-Hobson desk, computer, monitor, seven (7!) measuring probes, each of which is very expensive to purchase. There is also a sample/sample lens (hemisphere) for calibration! The very detailed operating manual is on the USB stick, and it also contains all the circuit diagrams and functional diagrams! The system will be shipped on two Euro pallets using a freight carrier. It is already securely fastened to the pallets. The Talyrond 265 and the desk will be well-protected with bubble wrap, etc., and secured with stretch film for transport. The system itself is fixed with "transport safety screws." Shipping costs within Germany are included; I will cover them! So, within Germany: FREE SHIPPING! The measuring system should definitely be assembled and put into operation by a Taylor Hobson service technician, who can then also recalibrate the system on-site. This is now recommended after a few years. Mistakes can be made during assembly and commissioning. For example, some locking screws are installed for transport; if you forget to remove them, the system could be damaged when it starts up. A truly well-maintained, very accurate system that will provide excellent service for many years to come!!

Condition: excellent (used), functionality: fully functional, Year of construction: 2018, control type: CNC control, degree of automation: automatic, actuation type: electric, laser type: fiber laser, laser power: 3,000 W, pipe diameter (max.): 210 mm, pipe length (max.): 6,000 mm, workpiece weight (max.): 800 kg, input voltage: 400 V, type of cooling: water, overall weight: 5,000 kg, total length: 12,000 mm, total width: 2,000 mm, Equipment: CE marking, cooling unit, documentation/manual, dust extraction, emergency stop, safety light barrier, FOR SALE: High-Precision 3000 W Fiber Laser Tube Cutting Machine (6 m) Industrial-grade 3 kW tube laser equipped with a side-loading system, a premium IPG YLS 3000 laser source, and a German LT Ultra bevel cutting head. A powerful and versatile solution for cutting round, square, rectangular, and oval tubes, as well as special profiles, with bevelling up to 45°. Machine origin & key details Loading system: side-loading Year of manufacture: 11/2017 (commissioned in Finland in 2018) Laser source: IPG YLS 3000 – 3000 W fiber laser, manufactured in the USA Bevel cutting head: LT Ultra-Precision Technology, manufactured in Germany Filtration: Welldone dust collector and filtration unit Ijdpfozuf Dhex Aidsif Key highlights Versatile tube profiles – round, square, rectangular, and oval tubes, plus open and custom shapes 3D bevel cutting – integrated bevelling up to 45° for high-precision weld preparation High speed & accuracy – max. operating speed 100 m/min, acceleration 1.0 G, positioning accuracy ±0.03 mm Heavy-duty capacity – tubes up to 6 m in length, max. load 800 kg Technical specifications Parameter Specification Laser power 3000 W (3 kW) Laser source IPG YLS 3000 (manufactured in the USA) Bevel cutting head LT Ultra-Precision Technology (manufactured in Germany) Filter / dust collector Welldone Loading system Side-loading Year of manufacture 11/2017 (commissioned in Finland 2018) Max. material length 6000 mm (6 m) Round tube diameter Ø 20 – Ø 210 mm Square / rectangular tube size 20 × 20 mm – 150 × 150 mm (any side) Bevel cutting angle ≤ 45° X/Y positioning accuracy ±0.03 mm X/Y repeat positioning accuracy ±0.02 mm / 1000 mm Cutting gap width 0.1 – 0.2 mm Max. operating speed 100 m/min Max. acceleration 1.0 G Max. loading capacity 800 kg Machine weight 4000 kg Machine dimensions (L × W × H) 12 000 × 2500 × 1900 mm Gross power < 40 kVA Power supply 380 V ±5 %, 50 Hz Operating temperature / humidity 0 – 40 °C / < 90 %

Condition: good (used), Year of construction: 2014, total width: 600 mm, total length: 1,000 mm, total height: 600 mm, Manufacturer: MIBA Type: RNF-65 Year: 2014 Milling cutter laser guided Working range 2000 - 8000 mm Designed for mobile use on a 3000 mm gauge Specifications Metric US Standard There are (currently) no specifications for this machine. Iisdewq Hp Tspfx Aidef Dimensions (estimated) There are (currently) no dimensions for this machine. Please note: The information on this page has been provided to the best of our knowledge and, as far as possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not constitute representations or contractual terms. We recommend that you verify all important details.

Condition: excellent (used), Year of construction: 2013, operating hours: 32,269 h, functionality: fully functional, machine/vehicle number: 2067-2091, WALTER Helitronic Basic 2013 For sale is Walter Helitronic Basic CNC tool and cutter grinding machine. It is in excellent working condition. Machine can be inspected by appointment. Price on request, loading on truck included. Possibility of shipping Worldwide. TECHNICAL CHARACTERISTICS WALTER Helitronic Basic 2013 No. 2067-2091 Working hours 32269 [h] CNC control FANUC 310i Software: Tool Studio Version 3.5 Number of axes 5 Travel path: X= 470mm Y=330mm Z=640mm Spindle rotation speed: 10500 rpm Traversing feeds X, Y and Z axes 15000 [mmmin] A axis 360 [°] C axis +- 200 [°] Max. workpiece lenght peripheral grinding 350 [mm] Max. workpiece lenght end face grinding 280 [mm] Max. grinding diameter 320 [mm] Max. grinding diameter with automated work table 290 [mm] Grinding spindle attachment NCT Grinding spindle diameter 70 [mm] Max. diameter grinding wheel 150 [mm] Max. part weight in part holder headstock 20 [Kg] Coolant pump pressure 7 [bars] Collant pump flow rate 80 [lmin] Lubrication tank capacity 350 [l] Iodpfx Aiewu Nw Uedeif Supply voltage 400 [V] Grinding spindle motor power: 7 kW Tool holder: ISO 50 Weight: 4500kg EQUIPMENT INCLUDED x1 Software TOOL STUDIO 3.5 x1 RENISHAW tool probe x1 DSL AIR TECHNOLOGY AES-SIGMA 20 type oil mist extractor x1 lubrication tank x1 paper band filtration unit x1 GRUNDFOS coolant pump x1 machine parameter backup x3 technical manuals (paper format) x1 technical documentation (CD-ROM format)

Condition: excellent (used), Year of construction: 2025, functionality: fully functional, CARRIER 09VE 1064 WATER DRY COOLER – YEAR 2025 Industrial Carrier dry cooler featuring a V-shaped coil, two independent water circuits and axial fans. Supplied with a steel support frame, electrical control panel and DN 65 hydraulic connections. TECHNICAL DATA Manufacturer: Carrier Model: 09VE 1064 UI 1270A9B 12A1V1 CU Isdpfx Aozvf Eboideif Product reference: 7416018.702174 Serial number: 04136261/0001 Year of manufacture: 2025 Working fluid: Water Number of circuits: 2 Volume per circuit: 120 litres Maximum working pressure: 13 bar Maximum temperature: 110 °C Hydraulic connections: DN 65 Power supply: 400 V / 3-phase + N / 50 Hz Electrical power input: 35 kW Rated current: 46.8 A Weight: 1,340 kg PED: 2014/68/EU PED classification: Article 4.3, Group 2 liquid Certifications: CE, UKCA and EAC The unit is installed outdoors and available for inspection. The scope of supply includes the dry cooler and its electrical control panel.

Condition: good (used), Year of construction: 1982, Plate dimensions 2200 x 1100 mm Daylight opening 350 mm Number of daylights 1 St. Iijdpoyyqnxsfx Aidef Heating elektrisch Total pressure 65 to Motor output 1,1 kW Dimensions (L/W/H) 2540 x 1280 x 1900 mm weight of the machine ca. 2500 kg

Year of construction: 2023, condition: new, functionality: fully functional, 3 UNITS JWELL - 65 TWIN-SCREW CONICAL EXTRUDER Iijdpey Sxizofx Aidef

Condition: used, Year of construction: 2007, controller manufacturer: Siemens, controller model: 840 D, _____ Description: Year of manuf. : 2007 Control : Siemens 840 D Turning diam. : 250 mm Turning length : 650 mm In General: Year of construction:2007 Control:Siemens 840 D Bar capacity:65 mm Turning diameter:350 mm Turning length:650 mm Main spindle: Technology:Motor spindle Speed:5,000 rpm Power max.:35 kW Torque max.:370 Nm C-axis:0.001 Bar capacity:65 mm Chuck:Hainbuch Spanntop size 65 Clamping cylinder:Hollow clamping cylinder Sub spindle: Technology:Motor spindle Speed:5,000 rpm Power:26 kW Torque:290 Nm C-axis:0.001 Chuck:Hainbuch Spanntop size 65 Clamping cylinder:Partial hollow clamping cylinder Z-axis:670 mm X-axis:175 mm Tool carrier i (X/Y/Z): Technology:Tool turret, 12 stations Tool holder:VDI 30 Tool drive:4,000 rpm, 11 kW, 28 Nm X-axis:300 Y-axis:80 mm ( +/- 40 mm) Z-axis:650 mm Tool carrier II (X/Z): Technology:Tool turret, 12 stations Tool holder:VDI 30 Tool drive:4,000 rpm, 11 kW, 28 Nm X-axis:180 Z-axis:650 mm Equipment: Ijdpfx Asyamfloidsif Chip disposal:Chip conveyor Coolant supply:IKZ system Measuring systems:Direct in all X-axes (glass scales) Bar loader:IRCO Breuning Part removal:Finished part gripper + indexing belt Emulsion mist separator:Mechanical Set-up mode:Electronic handwheel

Condition: used, Year of construction: 1901,

Condition: excellent (used), METALLKRAFT Profile Steel Shear / Punch HPS 65 DS Combined Hydraulic Profile Steel Shear and Punch with Punching Station, Notching Station, and Flat Steel, Angle Steel, and Profile Steel Shear – enables simultaneous operation at punching and profile steel shear. Punching Station - Punching Force: 65 t - Punching Capacity: max. Ø 26 x 20 / Ø 57 x 10 mm* - Throat Depth: 305 mm - Stroke Length: max. 55 mm - Number of Strokes: 25 strokes/min - Working Height: 900 mm Rod Steel Shear - Cutting Capacity Round: max. Ø 45 mm* - Cutting Capacity Square: max. 45 x 45 mm* Angle Steel Shear - Cutting Capacity L-Profile 90°: 120 x 120 x 12 mm* - Cutting Capacity L-Profile 45°: 70 x 10 mm* - Cutting Capacity U/I Profile: 120 x 58 mm - Cutting Capacity T-Profile: 90 x 11 mm - Working Height: 1,140 mm Flat Steel Shear - Cutting Capacity 90°: max. 300 x 20 / 375 x 15 mm* - Miter Cut 45°: max. FL 100 x 15 mm* - Blade Length: 380 mm - Working Height: 900 mm Notching Station - Material Thickness: max. 10 mm* - Notching Width: max. 45 mm - Notching Depth: max. 90 mm - Notching Station: 100 x 100 x 10 mm Machine Data - Motor Power: 5.5 kW | 400 V - 50 Hz - Dimensions (LxWxH): 1700 x 950 x 1880 mm - Weight (net): approx. 1,600 kg Shipping on pallet via freight forwarder possible Europe-wide. Additional machines available! Take a look at our listings. If you have any questions, feel free to contact us by message or phone: Maschinenhandel Nord Gerstenstraße 2 17034 Neubrandenburg Iedpexizansfx Aidsif

Condition: good (used), Year of construction: 2010, functionality: fully functional, The machine is in good technical condition. Travel in the X-axis: 1100 mm Ijdpfozvfglox Aidsif Travel in the Y-axis: 650 mm Travel in the Z-axis: 600 mm Max. spindle speed: 8000 rpm Number of tools in the magazine: 40 Dimensions of the work table: 1300 x 650 mm Inspection during operation is possible upon agreement.

Condition: like new (used), functionality: fully functional, Digital torque wrench Stahlwille Manoskop 730D/65 Measuring range: 65 - 650 Nm Iijdpfx Aeytqhwsidef

Condition: reconditioned (used), Year of construction: 2021, operating hours: 73 h, functionality: fully functional, working width: 650 mm, area performance: 3,200 m²/h, overall weight: 391 kg, warranty duration: 12 months, water tank capacity: 74 l, HAKO SCRUBMASTER B70 CL TB650 SCRUBBER NEW 6V 175Ah SIAP GEL BATTERIES (4x) Manufactured in 2021 with 73 hours of operation 650mm cleaning head (TB650) equipped with two new medium-hard disc brushes for use on any surface. Iedpfxszvd Ihe Aidsif New polyurethane squeegee rubbers, resistant to oil, grease, and petroleum products. A built-in battery charger and wheel drive simplify daily operation. The device is equipped with a new, durable drain hose and a new suction hose. The new suction turbine ensures high water suction power from the squeegee. Each device we offer has individually taken photos; you buy exactly what you see. TECHNICAL DATA: Power supply voltage (V): 24 Brush working width (mm): 650 Suction nozzle working width (mm): 950 Theoretical capacity (m²): 3200 Working speed (km/h): 5 Tank capacity (l): 72/74 Weight (kg): ~391 Power (kW): 2.28 INCLUDED: NEW 6V 175Ah SIAP GEL BATTERIES (x4) NEW disc brushes 330mm PPL 0.5 (2x) NEW 24V 500W suction turbine NEW suction hose NEW drain hose NEW head guard rubber Squeegee blade with new oil-resistant rubbers Built-in battery charger 5 liter Tenzi Normal fluid - FREE KEY FEATURES: The 72-liter tank allows for a large volume of cleaning solution, eliminating the need to frequently stop for refills. The machine's design makes it highly maneuverable. The small turning radius allows for operation even in narrow passages and alleys. The parabolic squeegee beam ensures precise solution extraction from the cleaned surface. The large working width (650mm) ensures high surface coverage. The control panel is easy to read and intuitive to use.

Condition: ready for operation (used), Year of construction: 2009, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2009 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 x 65 cm Iodpozuxv Dsfx Aideif Condition: very good! Video of machine in operation available on request.