Used lowboy semi-trailers / low loaders for sale (201)

Condition: new, maximum load weight: 73,540 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Hydraulically extendable/retractable and lowerable gooseneck, length ± 3,650 mm * 2 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the middle section of the gooseneck (LC 10,600 daN) * Suitable for 6 x 4 or 8 x 4 tandem axle vehicles Compact front axle: * Hook receiver at the front and rear, length: approx. 2,200 mm * Axle width: approx. 2,850 mm Excavator bridge: * Telescopic excavator bridge with traversable bridge hooks at the front and pin-and-plate coupling at the rear * Overall width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance approx. 150 mm 4-axle rear axle: * Mechanical pin-and-plate coupling for mounting a low-bed trailer at the front * End crossbeam at the rear, axle width: approx. 2,850 mm * Axle length: approx. 5,480 mm Swivel axles, all axles hydro-mechanically force-locked * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle suspension Tires: * Front axle: * 8 x tires, selection according to manufacturer (M+S) 285/70 R19.5 * Rear axle tires: * 16 x tires, selection according to manufacturer (M+S) 285/70 R19.5 * Load index 150/148J Painting: * Complete steel construction automatically blasted with a shot blasting system after welding. Second blasting with corundum for optimal adhesion of the coating system. * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection. * Final painting with 2 layers of 2K topcoat, single-color in RAL 3002 carmine red, according to the RAL 841GL system. Including the following accessories: * Steel front panel, approx. 400 mm high * Aluminum side and rear walls, pluggable on the gooseneck, approx. 400 mm high, in anodized finish * 3.5-inch kingpin * Truck hydraulic connection with flow control (20 l/min) * Gantry for suspending the supply lines; the SZM tank must have a minimum capacity of 80 liters. * With MAX Trailer coupling parts; otherwise, coupling parts must be supplied by the customer. Gedpfx Agsxbmplevsbt * BEKA-MAX central lubrication for one gooseneck with standard grease NLGI-2 * Tool kit, type No. 612452 * Multi-coupling hydraulic connections on the gooseneck * Front axle with a separate air connection for air suspension * BEKA-MAX central lubrication for a 2-axle axle with standard grease NLGI-2 * One 7-pole socket on the left and right at the rear of the front axle for warning signs * Screw-in option (approx. 40 mm diameter) every approx. 500 mm on the outside of the top chord of the outer beam of the excavator bridge for screw rings (LC 16,000 daN) * Foldable wideners with steel mats, adjustable in width from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX central lubrication for a 4-axle axle with standard grease NLGI-2 * On the rear axle, a socket for the cable remote control of the trailing axle * Rear axle with tipper body * Two INOX toolboxes, approx. 855 x 340 x 390 mm, on the gooseneck, left and right * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the power pack, start/stop of the diesel engine

Condition: new, maximum load weight: 29,260 kg, overall weight: 42,000 kg, axle configuration: 3 axles, loading space length: 13,200 mm, loading space height: 900 mm, total width: 2,550 mm, total height: 3,570 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer SLAR3 Tele Lowboy Trailer with Wheel Recesses Technical Data: Model and Manufacturer: Model: Kässbohrer K.SLA R 3 / 1N - 18 / 30 * Manufacturer: Kässbohrer Gbsdpfxox Epaqj Agvst * Type: Extendable, wheel recess lowboy trailer, suitable for the transport of vehicles and heavy machinery. Dimensions: * Overall length: 13,190 mm * Gooseneck length: 3,950 mm * Platform length: 9,240 mm * Extension: 3,500 mm * Overall width: 2,550 mm (expandable by 600 mm via side extensions) * Fifth wheel height: 1,250 mm * Platform height: 875 mm * Ramp length: 2,750 mm * Ramp width: 850 mm * Wheelbase: 7,800 mm * Axle distance: 2,260 mm Weights and Load Capacities: * Permissible total weight: * 52,800 kg at 60 km/h * 48,000 kg at 80 km/h * Tare weight: 12,744 kg ±3% * Axle load capacity: 30,000 kg (10 tons per axle) * Fifth wheel capacity: 18,000 kg Axle Configuration: * Number of axles: 3 (2 fixed axles at the front, 1 trailing axle at the rear) * Lift axle: Manually controlled, load-dependent (1st axle) * Axle material: BPW axles with drum brakes Tires and Rims: * Tire size: 245/70 R17.5 * Tire brand: GOODYEAR * Tire markings: M+S label and 3PMSF marking * Tire pressure monitoring system: Increases fuel efficiency and extends tire life * Number of rims: 12 pieces (steel rims with offset ET120) Chassis and Suspension: * Suspension: Air suspension with load gauge * Braking system: Two-line pneumatic brake system by WABCO, EBS 4S/3M with ABS and RSS (roll stability program) Lighting and Electrical System: * Lighting system: 24V, multi-chamber lights by ASPÖCK, side markers, and rear lights in LED * Coupling type: Standard yellow/red for air supply connection * Connections: NATO socket with 2 x 50mm² intermediate cable (3 m length) Ramps: * Ramp type: Folding hydraulic ramps with sliding mechanism * Capacity: 40 tons * Ramp surface: Made of hardwood * Safety devices: Ramp protection chain included Load Securing: * Tie-down points: * 2 x 2 with a load capacity of 5,000 daN each * 1 x 2 with a load capacity of 10,000 daN on the gooseneck * 4 x 2 tie-down points with a capacity of 6,000 daN in the platform area * Container lock housings: Suitable for the transport of 1 x 20 FT or 1 x 30 FT container * Stake pockets: 5 x 2 stake pockets (50 mm x 100 mm) Special Features: * Gooseneck: With 90° vertical corners, stable and durable * Floor covering: 45 mm thick hardwood floor and steel floor with a drop-pattern structure * Wheel recess bridge: Bridges made of split hardwood pieces with sheet metal supports to cover the wheel recesses * Tool box: PVC-coated steel, dimensions 750 x 400 x 360 mm Colors: * Chassis: Traffic red (RAL 3020) / also available in black * Partial metallization of the support surfaces Condition: New and ready for immediate use. * Perfectly suitable for heavy transport and for use in the construction industry or for relocating machinery.

Condition: new, maximum load weight: 36,461 kg, overall weight: 49,500 kg, axle configuration: 3 axles, total width: 2,480 mm, total height: 860 mm, Year of construction: 2026, Technical Description Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm thick hardwood flooring. Loading Platform: Loading platform behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel of approx. 1,000 mm x 8°. 6 pairs of outward-folding lashing rings (LC 5,000 daN). 2 pairs of outward-folding lashing rings (LC 10,000 daN). 1 pair of inward-folding lashing rings on the front central beam (LC 10,000 daN). Grating flooring C40/4 (point load 2.3 t on an area of 20 x 20 cm), over the axles with chequer plate covering. Two-Part Steel Ramps: One pair of galvanized, two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with grating flooring C40/5 (point load 8 t on an area of 20 x 20 cm). Ramp with hydraulically foldable ramp sections and hydraulic lifting system. Maximum load per pair: 40,000 kg In accordance with regulation 1230/2012/EU, ramps less than 300 mm in length do not count towards the vehicle length of 16,500 mm in driving position. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Tyres 235/75 R17.5 3PMSF as per manufacturer’s choice. Gsdpew Dl Hwofx Agvjbt TPMS: TPMS tyre pressure monitoring system as per ECE R 141. Data transmission to the tractor unit via the standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be able to receive and display these data. Axles: BPW axles and suspension, 2 fixed axles, 1 self-steering trailing axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated via reverse gear and manually. Air suspension with raise and lower valve. Axle tools included. Brake System: WABCO braking system compliant with EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit. Electrical System: Electrical system compliant with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicator. ASPÖCK-UNIBOX on the front connector strip with 24N, 24S & 15-pin sockets. Connection according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: Steel frame made of high-strength fine-grain steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Tarp Structure: Tarp structure approx. 3,960 mm – Galvanized front wall with a tensioning mechanism for the sliding curtains. – “EDSCHA” roof, forward-sliding on aluminum roof rail profiles (bolted to front and rear walls). – 3 pairs of movable stanchions on the loading platform. – Body can be hydraulically widened at the rear by approx. 750 mm to the left and right. – Sliding roof with upward-swinging portal carrier. – Sliding tarp with 700 mm length reserve and tensioning straps at approx. 600 mm intervals. Height to top edge of structure approx. 3,960 mm (loaded). – Driving with open sliding roof is not permitted and will cause damage to the tarp. Painting: Entire steel structure is automatically shot-blasted after welding using a blasting wheel system. Second blasting treatment with corundum for optimal coating adhesion. Full metallizing of the entire chassis with ZINACOR 850 (85% zinc / 15% aluminum) for best corrosion protection. Top coat with 2 layers of 2K finish, single-color in a shade of your choice according to the RAL 841GL standard. Rear section metallized and coated in RAL 9010 (pure white). No metallic paint.

Condition: new, maximum load weight: 33,865 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, Excerpt of Equipment Gooseneck * with angled front corners approx. 45° and rear angle approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood decking approx. 30 mm thick Loading Platform * in double-extendable design with rear angle approx. 500 mm x 8° * 6 pairs of lashing rings that fold outwards (LC 5,000 daN) * 4 pairs of lashing rings that fold outwards (LC 10,000 daN) * 1 pair of lashing rings positioned horizontally at the front of the loading platform (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Hardwood decking approx. 48 mm thick, with diamond plate decking over the axles * Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Axles * BPW axles and suspension, all axles with hydro-mechanical forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tool Tires * 245/70 R 17.5, load index (146/146 F) * Brand of our choice Kingpin * JOST kingpins (mechanical) with 2-speed gear for approx. 24 t lifting capacity (approx. 50 t test load) Braking System * in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the semi-trailer tractor Painting Gedpjzlwm Nofx Agvebt * First-class and durable corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) * Topcoat, single color in RAL 3002 carmine red * Rear section metallic and painted in RAL 9010 (pure white) * Metallic paint not possible Steel Construction * made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical System * in accordance with EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection bar with sockets 24N, 24S & 15 pole * Connection according to ISO. 24N ISO-1185 24S ISO-3731 15 pole ISO-12098 Incl. the following additional equipment * 2-inch kingpin * One galvanized steel front panel, approx. 400 mm high * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with holder on the front panel (± 5kg) * A spare wheel holder in front of the front panel * Electro-hydraulic power unit (± 45kg) * Steering from the front and rear by means of cable remote control operated via push buttons, with single-axle control (without installation in the tractor unit) * Mounting at the rear of the gooseneck for aluminum loading ramps * European reflector plates (red-yellow) at the rear of the trailer * Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer * On the gooseneck and at the rear panel, one holder each on the left and right for warning signs including socket * Mounting rail for aluminum loading ramps at the rear of the vehicle * A holder for a rotating beacon at the rear of the trailer * Galvanized folding supports under the angle of the loading platform * A mud flap at the rear of the trailer * Manual and description on USB stick * Speed stickers 80 km/h at the rear and on both sides * Load gauge for determining the axle loads including load diagram.

Condition: new, maximum load weight: 46,800 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory with vehicles available for immediate and short-term delivery on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck * Gooseneck with beveled front corners at approximately 45° and a rear bevel of approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick Extendable platform * with rear bevel of approximately 1,000 mm x 8° * 5 pairs of lashing rings that fold outwards (LC 5,000 daN) * 3 pairs of lashing rings that fold outwards (LC 10,000 daN) Gbedpfozk S Dmjx Agvet * 1 pair of lashing rings, lying horizontally at the front of the platform (LC 10,000 daN) * Recesses in the outer frame of the platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring, approximately 48 mm thick, with non-slip steel plate flooring over the axles Axles * BPW axles and suspension * 1st axle rigid, all other axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tool kit * Tires * 245/70 R 17.5 3PMSF * Load index (146/146 F) * TPMS: TPMS tire pressure monitoring system according to ECE R 141 Kingpin * JOST kingpins (mechanical) with 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load) Braking system * in accordance with EU regulations with EBS-E (4S3M) Paint finish * Complete steel construction automatically blasted with a blasting wheel system after welding * Second blasting with corundum for optimal adhesion of the coating system * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure the best corrosion protection * Final coating with 2 layers of 2K topcoat * solid color in RAL 3002 carmine red according to the RAL 841GL system * Rims in silver gray. Rear section metallized and painted in RAL 9010 (pure white) * Metallic paint not possible * Paint structure tested in the salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Steel construction * made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system * in accordance with EU regulations Lighting * 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the turn signal * ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pole sockets * Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pole ISO-12098 Incl. the following additional equipment * 2-inch kingpin * One galvanized steel front wall, approximately 400 mm high * Electro-hydraulic unit (± 45kg) * Steering from the front and rear via cable remote control, operated via push buttons, with single-axle steering (without installation in the central beam) * 1 pair of recessed lashing rings along the central beam at the rear in the bevel (LC 10,000 daN) (± 3kg) * On the gooseneck, aluminum side boards and rear wall, pluggable, approximately 2,440 x 400 mm (L x H) * The rear galvanized plug-in stakes are removable. (Length of the structure approximately 2,560 mm) (± 46kg) * A galvanized toolbox, integrated in the beveled gooseneck (± 47kg) * 3 pairs of WADER container pockets in the platform for a 20' (30?) or a 40? container (± 30kg) * 6 pairs of stake pockets for plug-in stakes, approximately 100 x 50 mm, in the outer frame of the platform (± 18kg) * Extensions, galvanized, extendable by app

Condition: new, maximum load weight: 48,930 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck * with beveled front corners, approximately 45° and with rear bevel approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick Loading platform * in a double-extendable design with rear bevel approximately 500 mm x 8° * 5 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 4 pairs of lashing rings, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally at the front of the loading platform (LC 10,000 daN) * 1 intermediate table, approximately 250 mm * Recesses in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring, approximately 48 mm thick, with diamond plate flooring over the axles Axles * BPW axles, hydro-mechanically forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires * 245/70 R 17.5 3PMSF, load index (146/146 F) * TPMS tire pressure monitoring system according to ECE R 141 Kingpin * JOST kingpins (mechanical) with a 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load) Braking system * according to EU regulations with EBS-E (4S3M) Steel structure * made of high-strength fine-grained steel * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) * S690QL/S700MC (yield strength 690 MPa) Electrical system * according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the turn signal * ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Painting * Complete steel structure automatically blasted after welding using a blasting wheel system * Second blasting with corundum for optimal adhesion of the coating system * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Final coating with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system * Rims in silver. Rear part metallized and painted in RAL 9010 (pure white) * Metallic paint is not possible * Paint structure tested in the salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Including the following additional equipment 2 inch kingpin * Electro-hydraulic unit (± 45 kg) * Follow-up steering from the front and rear, controllable by means of a cable remote control via push buttons, with single-axle control (without installation in the central control unit) Gbjdpfx Agozlwm Ajvet * One bracket for warning signs on the left and right of the gooseneck and on the rear panel, including socket * One bracket for a rotating beacon on the rear of the trailer * Aluminum side panels and rear panel on the gooseneck, pluggable, approximately 2,440 x 400 mm (L x H) * The rear galvanized stake pockets are removable. (Length of the superstructure approximately 2,560 mm) (± 46 kg) * A tool box, galvanized, integrated into the beveled gooseneck (± 47 kg) * 4 pairs of WADER container pockets in the loading platform for a 20', 2x 20', 40 or a 45' container (± 40 kg) * 7 pairs of stake pocket for stake pockets approximately 100 x 50 mm in the outer frame of the loading platform (± 21 kg) * Extensions, galvanized

Condition: new, maximum load weight: 90,700 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, total width: 2,850 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Extract from the specifications. Complete equipment list available upon request. Gooseneck: Gooseneck hydraulically liftable/lowerable and detachable. Length approx. 3,650 mm. For tractor units: 6x4 or 8x4 3-axle compact front bogie: * Hook mounts at the front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Godpfxew Tgp Ds Agvebt Lowbed: * Lowbed ATX-A with telescopic longitudinal beams in low design with fixed hardwood floor approx. 50 mm thick * With drive-over bridging hooks at the front and pin-lug coupling at the rear * Base width: approx. 2,850 mm, Length: approx. 7,150 mm, Beam height: approx. 330 mm, Beam width: approx. 750 mm * Loading height approx. 480 mm with ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical pin-lug coupling for mounting a lowbed at the front, rear end traverse at the back * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendle axle 3-axle front bogie: * PENDLE-AXLE, all axles hydro-mechanically forced steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off cocks and lock pins for securing in raised position * Final painting of axles with 2 coats of 2-component paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Front bogie tires: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDLE-AXLE, all axles hydro-mechanically forced steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off cocks and lock pins for securing in raised position * Final painting of axles with 2 coats of 2-component paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Rear bogie tires: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure optimal corrosion protection * Final coat with 2 layers of 2-component topcoat, single color in RAL 3002 Carmine Red, according to RAL system 841GL Includes accessories: * Steel front bulkhead, approx. 400 mm high * Plug-in ALU side and rear boards on the gooseneck, approx. 400 mm high, anodized finish * 3.5 kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections at the gooseneck * Front bogie with a separate air connection for pneumatic screwdriver * BEKA-MAX central lubrication for a 3-axle bogie * Preparation for mounting of bolt-on container locks for 1 x 20' or 1 x 30' containers on the outer beams * Without container locks * Mounts for foldable extensions outside on the outer beams of the loading area * One 7-pin socket left and right, front and rear on the rear bogie for warning signs * BEKA-MAX central lubrication for a 5-axle bogie * Socket on the rear bogie for the cable remote control of the steering override * Rear bogie with trough * 2 LED reverse lights mounted on the rear panel * European reflector panels (red-yellow) at the rear * One mud flap at the rear * One LED beacon with bracket left and right on the rear traverse * Two INOX toolboxes 855 x 340 x 390 mm on the gooseneck, left and right * 1-cycle

Condition: new, overall weight: 80,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, More vehicles available. Excerpt from the equipment list below. Full equipment details on request. GOOSENECK: * Gooseneck in SNT design, optimized for loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * Suitable for tractors: 4 x 2, 6 x 2, and 6 x 4 * Detachable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for controlling all hydraulic functions except hydraulic winches * Gooseneck outer rail with mounting holes for screwable lashing rings. First hole approx. 200 mm from front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at rear part of gooseneck (LC 10,000 daN) * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized finish * On the gooseneck: 1 plug-in aluminum rear wall, approx. 400 mm high, anodized finish * Approx. 40 mm hardwood floor covering on gooseneck, checker plate covering over kingpin * 3.5-inch kingpin * Gooseneck guide plate for the fifth wheel, approx. 500 mm wide * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) * 2 pairs of lashing rings with retention spring hanging on the outer rails of the gooseneck (LC 5,000 daN) LOADING PLATFORM: * Extendable loading platform, length approx. 8,800 mm with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical lock bolt and reinforced locking positions; supply lines routed securely inside the extendable rails, automatically adapting to the current platform length * BPW axles and suspension; 1st axle steerable, all others force-steered via hydro-mechanics * 1st axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting/lowering valve * 235/75 R 17.5 3PMSF twin tires – brand at our discretion * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B – static test load 50,000 kg * Full-length hardwood floor, interrupted between axles, approx. 50 mm thick (increases slip resistance). – Long slots for removable and repositionable bridging elements Gbedpexarmaofx Agvot * At the front of the platform – 1 movable intermediate table, approx. 300 mm wide, for the large-cross-section sliding tube, with checker plate covering. – Front and rear with long slots for removable and repositionable bridging elements * 1 pair of lashing rings on front cross member (LC 10,000 daN) * 7 pairs of flush-mounted, fold-out lashing rings in the outer frame of the platform (LC 10,000 daN) * Extendable (galvanized) widened sections, approx. 230 mm per side (without wooden planks) * 1 pair of mechanical rear supports * Rear steering operable from front and rear via cable remote control, with single-track control of axles, without installation on the tractor * TPMS tire pressure monitoring sensors fitted to all wheels * Deck locking with conically welded locking profiles every 500 mm * Lock monitoring left and right on the trailer * Mechanical lock for intermediate table (approx. 300 mm wide) to secure the table when extended * 5 pairs of threaded blocks mounted on the extendable rail for the installation of M20 screw-in rings (LC 5,000 daN) BRAKING SYSTEM

Condition: new, maximum load weight: 25,300 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment details. Full specifications available upon request. Neck (Gooseneck) * Gooseneck in SNT design to optimize loading platform length * Approx. 3,750 mm long, hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg For tractors: 4x2 and 6x2 Godpfx Ajv Sw E Ajgvebt Kessel Bridge (Tiefbett section) * Low bed designed as extendable Kessel bridge in SUPER LOW design * Approx. 6,850 mm length * With mechanical locking * Service lines routed protected inside the extendable beams, automatically adjusting to match the low bed’s length Rear Chassis * Short version with closed outer frame and checker plate cover * Chassis with excavator trough, closed at the rear half to accommodate air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve Tires * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Brake system * Brand: WABCO, EBS-E according to EU regulations, without connection cable to the tractor unit Paintwork * 6-Coat final treatment * All-steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 coats of 2-component acrylic paint in a single color, followed by cavity sealing with special wax Trailer color * RAL 3002 Carmine Red * Rim color: Silver grey * Drop side color: Natural aluminum Accessories included * Removable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for hydraulic operations (except for hydraulic winches). Without supply connection installed on tractor unit * Spare wheel carrier in front of the gooseneck front wall * Side beams of the gooseneck with fixing holes for bolted lashing rings; first hole approx. 200 mm from the front, then at approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear taper of the gooseneck (LC 6,000 daN) * 2" king pin * Hydraulic cross member for supporting the gooseneck on the tractor unit or a dolly * Air connection with air gun at the gooseneck * 1 pair of steel ramps with climbing strips and securing pins to bridge the mountings of the low bed * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * Outer side beams of the loading area prepared for removable loading floor * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the inside carrier’s exterior of the loading area * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the outer carrier’s exterior of the loading area (LC 10,000 daN) * Cut-outs above the lashing rings in the outer carrier’s upper flange * Mechanical pin-tab coupling from low bed to rear chassis, for swapping the loading floor or installing extension beams, with electro-pneumatic-hydraulic couplings * The outer carriers of the low bed coated with anti-slip sand finish for slip resistance * 2nd ride height for high ride position, max. ± 50 mm from normal ride position, without installation of controls from the tractor unit * 1 pair lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Front and rear tapers

Condition: new, empty load weight: 10,400 kg, maximum load weight: 45,600 kg, overall weight: 56,000 kg, axle configuration: 3 axles, loading space length: 8,600 mm, loading space width: 2,550 mm, loading space height: 1,000 mm, suspension: air, tire size: 235/75R17.5, color: green, Year of construction: 2021, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 3 axles, air suspension, ABS (anti-lock braking system), extendable to 3m, hydraulic ramps, rear support, supports. Gjdpfxsw Rf N De Agvobt Body: 3-axle low-loader trailer with hydraulic loading ramps, 3 x 12t axles, drum brakes, loading height approx. 1030 mm, extendable to 3m, hydraulic ramps operated via its own electric pump! Independent hydraulic pump with electric motor, independent from the tractor unit, gooseneck length approx. 4m, low bed length approx. 8.6m! New vehicle from stock! EU type approval currently under review! ACCESSORY INFORMATION PROVIDED WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted!

Condition: new, maximum load weight: 36,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You will find our complete vehicle inventory, including immediately and soon-to-be available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. - Gooseneck in SNT design to optimize load platform length, approx. 3,700 mm long, with a rear taper approx. 1,000 mm x 6° - For tractors: 4 x 2 and 6 x 2 - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets - 3 kW electro-hydraulic power pack for hydraulic operations (excluding hydraulic winches). Without supply line installation on the tractor unit - Outer beams of the gooseneck with mounting holes for boltable lashing rings. First hole approx. 200 mm from the front, subsequent holes approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - One mounting hole at the rear upper part of the gooseneck’s outer beams for a boltable lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside the gooseneck’s outer beams (LC 5,000 daN) - 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) Gbsdpfxoyhkquo Agvjt - Grating covering on the gooseneck and rear taper with 5 mm steel reinforcement - 2" kingpin - Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) - Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m long) between trailer and tractor unit, with plug (NATO-NATO) - 1 pair of detachable aluminum side boards on the gooseneck, approx. 400 mm high, anodized finish CARGO AREA: - Cargo area, approx. 9,600 mm long, with rear taper approx. 900 mm x 6° - Cargo area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg - TPMS (Tire Pressure Monitoring System) according to ECE R 141 - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle with trailing steering. 3rd axle with electromagnetic reverse lock via reverse gear and manual activation - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tires. Brand of our choice, load index 143/141J (144/144F) - Mechanical landing legs with 2-speed gearbox and crank - Continuous grating flooring with approx. 5 mm steel plating for additional reinforcement, designed for point loads: on the lift bed and cargo area - Painted sand coating on the gooseneck cover plates as well as transition areas between neck and lift bed, lift bed and cargo area, and cargo area and ramps - 1 spare wheel mounting bracket under the cargo area to the right in front of the axles - Cut-outs in the outer frame of the cargo area and lift bed for attaching tie-down straps (LC 2,000 daN) - 11 pairs of recessed, fold-out lashing rings in the outer frame of the cargo area (LC 10,000 daN): 3 pairs in the lift bed outer frame, 8 pairs in the cargo area outer frame - 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 3 pairs in the lift bed, 8 pairs in the rear cargo area - Control valves for the hydraulic ramps located on the right side of the vehicle - 1 pair of foldable mechanical rear supports, single-hand operation HYDRAULIC LOADING RAMPS: - 1 pair of two-part AXS steel ramps, approx. 4,920 mm long, and a

Condition: new, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Extract from the equipment. Full equipment details available on request. GOOSENECK: Gbjdpfjy Auh Isx Agvst * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front wall, removable, approx. 400 mm high * ASPÖCK-UNIBOX * 3 kW electro-hydraulic power unit for hydraulic functions, excluding hydraulic winches * Approx. 40 mm thick hardwood decking above the gooseneck * 2-inch kingpin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Bracket at the rear of the gooseneck for ALU loading ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the front wall * 1 pair of stake pockets recessed on the gooseneck for plug-in stakes approx. 100 x 50 mm (located on the inside of the chassis rail) EQUIPMENT: * Loading platform length approx. 8,800 mm, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * A recess in the loading platform, extending into the tapered section to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adapt to the selected loading platform length * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: each 12,000 kg with air suspension and raise/lower valve * 235/75 R 17.5 3PMSF twin tires. Manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Module B – static test load = approx. 50,000 kg * Throughout the loading platform and between the axles, interrupted approx. 50 mm thick hardwood decking (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the telescopic tube with large cross-section. Intermediate table with offset loading platform and extendable mounting rails for aluminum bridging elements * Platform locking with conically welded locking profiles every approx. 250 mm. Includes pre-tensioning plate * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck cross member, approx. 700 x 410 mm (W x D) * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom (in case vehicle is equipped with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the platform between 1st and 2nd axle * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, which can also be used as widening planks (if vehicle is equipped with extendable widenings) * Lockable aluminum elements installed on the extension tubes of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasting painted...

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm * Permissible gross weight (60 km/h) 52,800 kg * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting * SmartBoard Gbedpfxow Ii A Aj Agvjt For further information please do not hesitate to contact us

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm * Permissible gross weight (60 km/h) 52,800 kg Gbsdpfx Agsw Nlzqsvjt * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting * SmartBoard For further information please do not hesitate to contact us

Condition: new, overall weight: 36,000 kg, loading space length: 13,300 mm, loading space width: 1,640 mm, loading space height: 3,770 mm, Year of construction: 2026, Equipment: ABS, Special vehicle for forklift transport. In-loader / intermediate loader for max. internal height of approx. 3,770 mm Godpfx Agevw Hm Tovjbt Offer price without optional equipment. Available equipment: Rear with loading lift / elevator suitable for loading and unloading on ramps. The vehicle is currently being manufactured and has a delivery time. On request, we will be happy to make you an offer with the desired equipment. For more information, please visit: or call us.

Condition: new, maximum load weight: 44,400 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,500 mm, loading space width: 2,550 mm, total width: 2,550 mm, total height: 300 mm, Year of construction: 2026, Equipment: ABS, DOLL NEXT DOLL NEXTTiefbett tera T3P-S3FS25 – 3-axle low-bed trailer from the rapid series by DOLL Fahrzeugbau GmbH, Oppenau – in the heart of the Black Forest. Ideal for demanding applications in tough off-road conditions, challenging terrain, and daily use on construction sites. Thanks to DOLL rapid-series manufacturing, the trailer is available at very short notice and ready for operation, subject to availability. Can be individually configured to meet your specific requirements. Technical Data * Permissible gross weight: 61,000 kg * Unladen weight: approx. 16,600 kg | Payload: approx. 44,400 kg * Chassis: 3 x 12 t pendulum axles * Extendable low-bed * Vehicle width: 2,550 mm * Loading height (loaded): 300 mm * Wheelbase: 1,360 mm Features * Removable gooseneck for significantly easier and faster loading and unloading * Smooth telescoping for efficient handling * High-quality hot-spray galvanizing for optimal corrosion protection and reduced downtime * Powder-coated and hot-dip galvanized add-on components – robust and long-lasting – rust-free Your Advantages at a Glance * Rapid availability * Robust & reliable – proven technology, ideal even under the most demanding conditions * Made in Germany – manufactured by DOLL Fahrzeugbau, Oppenau – over 145 years of experience in premium vehicle manufacturing Smart Technologies Our innovative approach combines top-level quality, performance, and cost efficiency. The steadily increasing demand for our low-bed semi-trailers is driving further development and implementation of cutting-edge technologies in series production. Gbjdpfeyytnbsx Agvjt Contact & Location Manufactured by DOLL Fahrzeugbau GmbH, Industriestraße 13, 77728 Oppenau (headquarters and production site) * Depending on customer location, the vehicles can be demonstrated directly at the factory or, in cooperation with our field sales team, at selected reference customers across Germany.

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Technical axle load per axle: 12,000 kg - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: Godpfx Agoxarl Nevsbt - Steel construction from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams - Without container locks

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm Gbodpfjyhi H Iox Agvet * Permissible gross weight (60 km/h) 52,800 kg * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting * SmartBoard For further information please do not hesitate to contact us

Condition: new, Year of construction: 2026, We have all Europe documents! We can delivery the trailers with FOB-EXW-CPT-CFR-CIF Gbedpfeqx Nd Rex Agvet If you have an interest please contact with us; For European Countries; For African Countries;

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-Axle MULTIMAX "PLUS" semi-trailer, air-suspended and with hydraulically forced steering axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h (legal) Total weight: 49500 kg / 31500 kg Fifth wheel load: 18000 kg Axle load: 31500 kg / 31500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin offset to rear approx.: 2,100 mm Fifth wheel height loaded approx.: 1205 mm Platform length approx.: 9,600 mm Extendable by approx.: ? Platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55 / +145 mm Axle spacing: 1,360 mm Total weight dependent on fifth wheel load: Yes Special permit required if exceeding country-specific regulations. Technical description Gooseneck: Gooseneck in SNT design to optimize platform length, length approx. 3,900 mm, rear with a bevel of approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor-trailer combinations: 4 x 2 and 6 x 2. Platform: Platform, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6°. Platform behind the gooseneck can be hydraulically raised and lowered, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating deck. Hydraulically folding ramp ends. Ramps can be individually hydraulically shifted outwards by approx. 235 mm and inwards by approx. 365 mm. Maximum load and angle of inclination according to technical data sheet: C470319 Maximum inclination angle with lowered platform: 9° Gjdpfxjizu Ntj Agvsbt Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tool. Tires: 235/75 R 17.5 3PMSF, twin tires. Manufacturer according to our choice Load index 143/141J (144/144F) Braking system: Braking system of the brand WABCO EBS-E according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" design according to EU regulations. (ASS 3) Metallization: Complete HRM metallization (High Resistance Metallization) Complete steel structure shot-blasted, then hot-dip galvanized with ZINACOR 850 (Zinc 85% - Aluminum 15%). Painting: 6-coat finish: Complete steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion primer. Top coat with 2 coats of 2-component paint (acrylic), solid color in RAL colors of your choice, followed by sealing of the cavities with special wax. Rims in silver. Multi-color and special paint finishes available at an extra cost. Steel structure: Steel structure made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders tested according to DIN-EN 287-1. Welding process MAG according to EN ISO 4063. Protective gas M21 according to EN ISO 14175 Front wall made of steel, plug-in, approx. 400 mm high Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX on the connection strip at the front with sockets 24N, 24S & 15-pole. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pole connection according to ISO-12098 If your pin assignment differs from the ISO connection standard, please inform us. "Anderson" socket on the connection strip at

Condition: new, maximum load weight: 44,000 kg, overall weight: 61,000 kg, axle configuration: 3 axles, Year of construction: 2026, Further information here: Gbjdpfxov D Abtj Agvet

Condition: new, maximum load weight: 27,000 kg, overall weight: 36,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, crane, Step-frame semi-trailer in roll-off tipper design 3 axles with disc brakes SAF axles Lift axle Tires 385/55 R 22.5 Gear-driven winch LED lighting Work lights 25-ton capacity in sliding/articulated design for container lengths up to 7,500 mm Roller height approx. 1,300 mm Hydraulic internal locking Soft stop Quick release Fifth wheel as loading platform with side boards 1 unit available in stock. Different equipment/design available on request. Gbedpfszirgxjx Agvst Further information available on request.

Condition: new, empty load weight: 5,500 kg, overall weight: 19,500 kg, axle configuration: 1 axle, loading space length: 11,800 mm, loading space width: 2,550 mm, loading space height: 1,100 mm, suspension: air, tire size: 215 75 17,5, Equipment: crane, 1x SAF or BPW axle Total weight: 19,500 kg Payload: 14,000 kg Empty weight: 5,500 kg Total length: 12,800mm + 1500mm Brake system: Wabco 2S-2M Gbodokqmuuopfx Agvot Electrical system: Aspöck Systems Air suspension Hydraulic rear extension in full width 2550mm and length 1500mm Semi-trailer completely galvanized / galvanized (100% galvanized / 100% galvanized) Tire size: 215/70 R 17.5 Tire brands: Pirelli, Goodyear, Fulda, Continental. 5th Wheel Height: approx. 1050mm - 1150mm (other saddle heights also possible) Hydraulic winch 8ton with remote control with pulleys 24v 4.5KW electro-hydraulic motor Steel ramp: 2 pieces Changes possible according to customer requirements Painting freely selectable / free of charge All documents COC, Tüv, etc. available for approval.

Condition: new, Year of construction: 2026, Equipment: ABS, 5 Axle Lowbed Godpjrlm Txjfx Agvebt Please get contact with us for more informaiton;

Condition: new, maximum load weight: 45,250 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete inventory of vehicles available for immediate and short-term delivery on our website. Excerpt from the equipment list. Full specifications available upon request. Chassis, stepped: * Special steel frame made from high-strength fine-grained steels, electrically welded at connection points * Generously dimensioned outer frame. 4-axle configuration * Wheel covers over the axles with spray suppression * All steel parts sandblasted * Side underrun protection made of anodized aluminum mounted * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the stepped area for the longest possible low-bed length in combination with AluLeg drop supports instead of telescopic support legs, maximum rear swing clearance of the tractor unit approx. 2,100 mm Special body with rear stake extension: * DINKEL – special body * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable for loading/unloading up to approx. 4,200 mm * Three sliding stakes per side with elastic relief Gedpfx Agewx Dbievebt * Additional intermediate stake lockings in roof beam and parked position, via pull cable and spring bolt * DINKEL – mechanical lift roof, height-adjustable * Lift roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments by adjusting the stakes * Front cover at bulkhead for driving operation under the tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, 450 pockets below, four rows of single pockets above. Only three rows of slats in the raised platform, spacings evenly distributed Floor: * Approx. 27 mm special waterproof bonded beech phenolic plywood, rough surface * Steel sheet in the wheel well area. Suitable for forklift traffic as per DIN standard * Outer frame flush with deck surface Brakes: * WABCO air brake system with EBS according to EC Directive 71/320, including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with mileage counter and axle load display * Including WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF with drum brakes in low-loader design * Air suspension with lift and lower device, total lift approx. 230 mm * Third and fourth axles as friction-steered trailing axles with electric and mechanical lock Twin tires: * 235/75 R 17.5, 16-ply. Make of our choice, including spare wheel holder * Without spare wheel Lighting: * According to EU regulations, including LED side marker lights * Position lamps in LED design * 2 additional reversing lights * 2 work lights on the inside front wall, upper section Paintwork: * Chassis and body in one color, RAL 3002 carmine red * Intermediate stakes, axles KTL-coated black * Corner stakes hot-dip galvanized * Plastic parts black * Galvanized parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply cable * Air suspension in ECAS design, operated on the trailer * Oversize signage front and rear in galvanized, infinitely telescopic design with installed marker lights, including sockets for rotating beacons (small signs) * Additional external release for sliding roof frame lock * 4 stake adapters for special outer frame profile, to lock intermediate stakes as needed * PVC sliding tarpaulin, color similar to RAL 9