RIGHT HEAD 7 POINTS

BIESSE

Condition: not inspected (used), Year of construction: 2009, functionality: unexamined, number of axes: 4, table length: 4,300 mm, table width: 2,200 mm, number of spindles: 40, tool diameter: 120 mm, TECHNICAL DETAILS Number of spindles for vertical drilling: 30 Number of spindles for horizontal drilling in X-direction: 6 Number of spindles for horizontal drilling in Y-direction: 4 Total number of vertical + horizontal spindles: 40 Number of controlled axes: 4 Maximum tool diameter: 120 mm Table dimensions: 4,300 x 2,200 mm Gsdpfxeyq Ez To Ah Setw Number of stations in tool magazine 1: 22 Number of stations in tool magazine 2: 8 MACHINE DETAILS Milling motor power: 12 kW Total installed power: 42 kW Control software: BIESSEWORKS EQUIPMENT • Automatic panel loading system • Automatic panel stacking system • Lift table • Conveyor system • Vacuum pump Note: The safety fences at the rear and on the loading table are missing and will only be supplied subject to availability. The machine is sold and delivered as-is, in its actual and legal condition (“as seen and approved”), based on photographic documentation and technical/commercial descriptive materials. The buyer has the right to inspect the machine prior to collection and assumes responsibility for installation, securing, and operation of the machine at the destination. External reference: 7087

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, workpiece height (max.): 90 mm, workpiece width (max.): 3,200 mm, workpiece length (max.): 3,200 mm, edge thickness (max.): 3 mm, The machine has the following configuration: Number of panel sizing/milling units on the left side: 5 Milling unit (AS10) Double finishing cutter, top and bottom 2 pre-milling units Milling unit Number of edge processing units: 10 End trimming Top and bottom trimming (rough) Fine trimming for chamfering and rounding Corner rounding (AR34, 4 motors) Edge milling (FB40, 1 motor) Gsdpfx Aheyq Avhj Sstw Edge scraping Belt sanding (1 motor) Glue scraping Polishing (2 motors) Spray device TECHNICAL DETAILS Minimum panel height: 10 mm Maximum panel height: 90 mm Maximum panel length: 3,200 mm Maximum panel width: 3,200 mm Minimum edge thickness: 0.4 mm Maximum edge thickness: 3 mm FEATURES Feed chain with carriers Pressure applied via rubber belt Panel guide rails with NC positioning Edge roll magazine with 6 positions Hot melt adhesive system for PUR adhesive NORDSON Roller set for edge pressing 4 pressure rollers with NC positioning Spray device mounted on upper cabinets The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photo documentation and descriptive technical/commercial documents. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operation of the machine at the destination. External reference: 7685

Condition: not inspected (used), Year of construction: 2011, functionality: unexamined, travel distance X-axis: 6,200 mm, travel distance Y-axis: 1,935 mm, workpiece height (max.): 250 mm, number of axes: 4, number of spindles: 40, TECHNICAL DETAILS Gtedpfx Aheyqzrne Sjw Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of vertical drilling spindles: 28 Number of horizontal drilling spindles in X-direction: 4 Number of horizontal drilling spindles in Y-direction: 8 Total number of drilling spindles: 40 Total number of tool change positions: 22 Number of suction traverses: 10 Milling unit Number of axes: 4 Motor power: 10.5 kW Automatic tool changer Edge banding unit Gluing unit Tool magazine Grooving unit Number of positions in tool magazine: 22 MACHINE DETAILS Main spindle power: 10.5 kW Total power: 31 kW EQUIPMENT Vacuum pump Safety net Chip conveyor The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the goods before collection and shall be responsible for the installation, securing, and use of the machine at the place of destination. External reference: 8011

Condition: ready for operation (used), Year of construction: 2021, travel distance X-axis: 4,140 mm, travel distance Y-axis: 1,270 mm, travel distance Z-axis: 275 mm, number of axes: 5, This 5-axis BIESSE Rover A 1242 was manufactured in 2021. It features a working range of 4140 mm in the X-axis, 1270 mm in the Y-axis, and 275 mm in the Z-axis. The machine is equipped with brushless motors and a PC-based control system for enhanced performance. If you are looking to get high-quality CNC wood machining capabilities, consider the BIESSE Rover A 1242 machine we have for sale. Contact us for further details. • Working range • Y (5-axis): 1270 mm Gtjdpsyt Rrvsfx Ah Sow • Y (4-axis): 1260 mm • Z (with H=74 mm vacuum modules): 230 mm • Z (with H=29 mm vacuum modules): 275 mm • Axes and drives • X & Y: Rack and pinion drive; accuracy class 6 • Z: Ball screw with preloaded nut; accuracy class ISO C7 • Motors: Brushless motors with digital drives via Mechatrolink system • Control system and PC hardware • Control: BH660 (PC-based) with WRT (Windows Real Time) technology • CPU: Intel Core i5 or higher • RAM: 16 GB • Storage: 256 GB SSD or higher • Monitor: 21.5-inch LCD color screen • Operating system: Windows with real-time process management extension • Connectivity: Ethernet card; USB ports • Electrical and pneumatic • Power supply: 380 / 400 / 415 V – 50/60 Hz • Control voltage: 24 V DC (stabilized power supply) • Cabinet cooling: Air conditioning system for operation up to 40°C (104°F) • UPS (uninterruptible power supply): 7–10 minutes runtime for data protection • Workpiece support (ATS system) • Workpiece supports: 8 ATS aluminum supports on linear guides • Module carriers: 24 carriers (132 × 132 × H41.5 mm) with pneumatic clamping • Set-Up Assistant (SA): Manual positioning with LED indicators; ±1.5 mm precision • Vacuum zones: 2 independent work areas in X; 2 independent clamping areas in X • Software and licensing • Primary software: NC-HOPS 7 MacroCAM • Safety and maintenance • Safety system: Bumper system (front and rear) for immediate stop upon collision • Protection: Polycarbonate transparent front plate and sound-absorbing cover • Lubrication: Automatic lubrication system for linear guides and rack/pinion Additional equipment • Vacuum pumps (supported/optional): Up to two units, 90/100 m³/h or 250 m³/h each

Condition: ready for operation (used), Year of construction: 2020, overall weight: 3,800 kg, This 3-axis BIESSE Selco WN 2 was manufactured in 2020. It features a robust machine weight of 3900 kg and operates on a power supply of 400 VAC with a consumption of 12 kW. The machine is designed for efficient panel cutting and includes a CE marking for compliance. If you are looking to get high-quality panel saw capabilities, consider the BIESSE Selco WN 2 machine we have for sale. Contact us for further details. • Electrical cabinet weight: 190 kg • Power supply voltage: 400 VAC • Full load current: 24 A • Number of power supply phases: 3 • Power consumption: 12 kW Gsdpfxoyt Rkls Ah Setw • Frequency: 50 Hz • Short circuit rating: 10 kA RMS • Compressed air supply: 6.5–7 bar • Required suction flow speed: 30 m/sec • CE marking: Yes

Condition: used, functionality: unexamined, Ferwood Code: AGG0062 – Manufacturer Code: 6314A0111 – Condition: Used – Functionality: Not tested – Compatible Machine: CNC BIESSE ROVER 23/24/27/30/346 – If interested, we offer an overhaul service, please contact us. Weight and dimensions for transport: 2.5 kg, 20x20x20 cm Gtjdpfx Ahjvu Auus Ssw

Condition: not inspected (used), functionality: unexamined, travel distance X-axis: 3,200 mm, travel distance Y-axis: 1,300 mm, number of spindles: 21, rapid traverse X-axis: 80 m/min, rapid traverse Y-axis: 60 m/min, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel distance X-axis: 3,200 mm Travel distance Y-axis: 1,300 mm Traverse speed X-axis: 80 m/min Traverse speed Y-axis: 60 m/min Traverse speed Z-axis: 25 m/min Number of suction traverse beams: 6 Spindles Number of vertical drilling spindles: 15 Number of horizontal drilling spindles in X-direction: 4 Number of horizontal drilling spindles in Y-direction: 2 Total number of spindles: 21 Milling unit Number of axes: 3 Max. spindle speed: 24,000 rpm Motor power: 9 kW Gjdpfx Ajytr Ryjh Sotw Tool changer Number of tool positions: 10 MACHINE DETAILS Total power: 26 kW EQUIPMENT Vacuum pump WINDOWS-based control system WRT machine programming software The machine is sold and delivered in its actual and legal condition ("as seen and approved") on the basis of photographic documentation and technical/commercial documents with descriptive character. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and operation of the machine at the destination. External reference: 8174

Condition: used, Year of construction: 2014, total height: 2,800 mm, total length: 6,900 mm, total width: 2,800 mm, Empty weight: 6.100 kg Price: On request - Details: - └ Description: Needs repair to B-axis and leaks to seals - Year: 2014 - Documentation available: No - CE certificate present: No - Serial number: 10333 - Number of milling spindles [pcs.]: 2 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - └ Milling spindle 2: - - Number of controlled axes [pcs.]: 3 - Type milling table: Beam table - Tool clamping system: HSK-F63 - Material clamp system: Pneumatic - Drilling unit present: Yes - Tool changer positions [pcs.]: 45 - Safety feature: Safety mat, Enclosed fence, Door interlock switches - Vacuum pump present: Yes - └ Number [pcs.]: 2 - └ Brand: Becker - └ Type: Vtlf 2.250 - └ Year of manufacture: 2011 - └ Main motor power [kW]: 5.5 - └ Capacity [m³/h]: 244 - └ Connection diameter [mm]: 60 - └ Vacuum pressure [bar]: 200 Gtedpfx Ahsyr Rnus Ssw - └ Oil free: Yes - Tools included: Yes - CNC documentation available: User keys/licenses, USB stick - Table length [mm]: 4800 - Table width [mm]: 1500 - Voltage [V]: 400 - Current consumption [A]: 39 - Fuse [A]: 63 - Power [kW]: 22.8 - Transport dimensions: 6900mm x 2800mm x 2800mm (l x w x h) - Transport weight [kg]: 6100kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: good (used), Year of construction: 2007, functionality: fully functional, input voltage: 380 V, input current: 36 A, input frequency: 50 Hz, type of input current: three-phase, actuation type: electric, overall weight: 3,200 kg, compressed air connection: 7 bar, Equipment: CE marking, For sale: a true workhorse. This machine isn't afraid of hard work or a tough hand. It's an old-school machine renowned for its reliability. Gtjdpfjyudkujx Ah Sow

Year of construction: 2020, condition: ready for operation (used), Main Drive Spindle motor power 13.2 kW Spindle Speed 24000 RPM Number of axis 3 Gtodpfx Aex Nr Npsh Sow Movement X-Axis Movement 3765 mm Z-Axis Movement 378 mm Y-Axis Movement 1560 mm This 5-axis BIESSE Rover PLAST A FT 1536 was manufactured in 2020, featuring a robust electro-welded base and high-precision movement systems. It boasts a main electrospindle power of 13.2 kW, a programmable rotation speed up to 24,000 RPM, and an 8-position revolver tool magazine. Ideal for intricate woodworking, it includes a 21.5" LCD monitor and Industry 4.0 integration. Consider the opportunity to buy this BIESSE Rover PLAST A FT 1536 CNC Wood Machining Centre. Contact us for more information. Application Types CNC Wood Machining