Condition: new, Year of construction: 2020, Guildolin Girotto GD 301D - automotive parts /labelling systems reel-to-reel / reeel-to-sheet machine The machine is NEW! Available immediately. - CONTINUOUS AUTOMATIC MECHANICAL-ELECTRONIC DIE- CUTTING MACHINES MOD. GD 301D - 10 tons of power – cutting plates 320 x 320 mm Useful cutting area 290 x 290 mm - fixed run 40 mm - electronic variator of speedy from 30 to 150 strokes per minute - KD/FM SYSTEM: triple unwind, the upper shaft is an unwind and it can be used as friction or motorised, the middle shaft can be used as motorised rewind or friction unwind, lower shaft is an unwind and it can be used as friction or motorised – according to the requirements. The motors at variable speed from digital inverter are placed on slides and the KD/FM group is assembled on the machine # n.3 photocells of end material # n.2 photocell of automatic feed # n.3 pneumatic expansion shafts diam.76mm with valve in the head # n.3 electronic brakes managed by ultrasonic sensors which detect the diameter of the roll of material and adjust the power of the brakes, managed by potentiometer. - guides on rolls on the inboard side - feeder rolls system on the inboard side before the change liner - the feeder rolls are covered in silicone rubber and motorized - KR SYSTEM: upper single motorised rewind controlled by inverter assembled on the machine and complete with 1 pneumatic expansion shaft diameter 76 mm with valve in the head for inflation - KF SYSTEM: upper friction unwind with guides and roll assembled to the machine and complete with n.1 pneumatic expansion shaft diam.76mm with valve on the head for inflation. Cjbvl Dkjuv Hnxjajgt N.1 electronic brake managed by ultrasonic sensor which detects the diameter of the roll of material and adjust the power of the brake, managed by potentiometer. - feeder rolls system on the inboard side after the change liner - the feeder rolls are covered in silicone rubber and motorized - touchers at rolls placed before and after the cutting plate - extractable rectified steel plate support cutting-knife and counter cutting-knife - the plate support cutting-knife is with guides at swallow tailed for a speed and easy change of the cutting-knife - K2 SYSTEM : scrap separator with transversal bar and roll covered with anti-adherent material - KR SYSTEM : upper single motorised rewind controlled by inverter assembled on the machine to rewind the waste removed by the K2 system complete with n.1 pneumatic expansion shaft diameter 76 mm with valve in the head for inflation. this shaft is equipped also with frontal mechanical friction for a lightly adjustment. - K3 SYSTEM: placed between the cutting head and the outboard feeder rolls group : # pneumatic group of evacuation pieces synchronized and run by the machine controller. The evacuation position is adjustable on the X. Y. Z. axes. This system is complete with support brackets for the counter matrix. - TL SYSTEM: longitudinal cut system with 5 razor blades and adjusting of the position of the blades on their axe - feeder rolls system on the inboard side after the TL system - the feeder rolls are covered in silicone rubber and motorized - CTT SYSTEM : passage of material 320 mm - pneumatic cutter assembled on machine for the transversal cut, heavy version for cutting materials with max thickness 15 mm, complete with motorized feeder rolls for the correct positioning of the material under the blades

Year of construction: 2020, Condition: excellent (used), Valliani Maximus 160V-123X162CM cutting plotter, year of manufacture 2020, serial number 5320011 Cjbouph Swjvl Dkasgt

Year of construction: 2009, Condition: used, Two-colour rotary flexographic printer with integrated slotter and stacker. TECHNICAL DATA: Year of production: 2009 Factory number: 0904K02 Max speed: 70 pcs/min Economical speed: 50 pcs/min Max. sheet: 3000 x 2000 mm Min. sheet size: 600 x 350 mm Max. print: 2900 x 1900 mm Cardboard thickness: 2-10mm Film thickness: 4-7mm Axial correction: ± 8mm Max slot length: 350mm Slit width: 7mm Main motor: 7.5 KW Total power: 15 kW Overall dimensions: 6000mm x 3050mm x 1900mm Cobjhbvq Hsvl Dkaogt Weight: 28000 kg DESCRIPTION: Includes commissioning, technology, training, start-up warranty.

Condition: reconditioned (used), The Lamina GL2200 gluing machine is designed for manual and semi-automatic gluing of cardboard packaging and POS materials. In the gluing process, two types of dispersion adhesives can be used: hot and cold. The machine uses both hot and dispersion adhesives. The machine is designed for manual feeding of cut materials and materials with precision grooves. The adhesive system applies adhesive to a predetermined length and position as the material passes through the workpiece. The pressure roller system ensures a perfect grip. The equipment's maximum working width is 2200 mm, which allows gluing large-format products. Thanks to the multi-functionality of the settings, the materials being glued can have different thicknesses. Material: Cardboard, corrugated cardboard; Cgebvl Dkerb Aqpsast Maximum width: 2200mm. Technology: Semi-automatic gluing machine; Material type: Cuts. We sell only our own equipment.

Condition: excellent (used), SIMPLACUTTER (CAUHE) III - 1480x1070 Machine little used, in very good condition Equipment: - pneumatic clutch and brake - control panel - quick release frame + additional frame - 3 modes of operation: single, continuous, with time delay on opening - central lubrication - additional safety guards - operating tools Cobvl Dkeuwrtioasgt - hard plate for pressure

Condition: excellent (used), Year of construction: 2001, overall weight: 1,650 kg, Box folding machine. Full documentation, excerpt in photos. Also available 2 other box assembly machines. Box assembly machine. Full specs available. Two other machines for box assembly available. If you have any questions please e-mail us. Cjbovcy Disvl Dkasgt

Condition: good (used), Year of construction: 1999, Guillotine for cutting. 150cm. Ready to work. Cgsbvjuhnu Iol Dkast Worldwide delivery possible.

Year of construction: 2022, Condition: excellent (used), Geminus cutting plotter, serial number: 7822001 Csbvl Dsuph S Rekajgt

Year of construction: 2002, Condition: refurbished (used), Machine for production of PE bags. It produces garbage bags and freezer bags of diffrent volume. For more information call the phone number. Csbvjh Ica Eol Dkasgt

Condition: new, Year of construction: 2022, Functionality: fully functional, Completely new equipment. Not used. Full description in the presentation. Cgobjrq Dz Ajvl Dkajt

Condition: excellent (used), SIMPLACUTTER (CAUHE) IV - 1680x1160 Machine little used, in very good condition, new upgraded electronics + laser protection Equipment: - pneumatic clutch and brake Cobvl Dkouwruajajgt - control panel - New upgraded electronics + laser protection - 3 modes of operation: single, continuous, with time delay on opening - central lubrication - additional safety guards - operating tools - hard plate for pressure

Condition: good (used), paperfolder , A4,A5, A6 Cgjbsu Tgpzsvl Dkast

Condition: used, Year of construction: 1994, Bottom lock Cobvljtz Hy Re Dkajgt 4/6 gluing points Ero Gluing system (year 2001) Can be used with solid board from 200gr to 1000gr Cardboard until 12mm

Year of construction: 2015, Condition: excellent (used), PLASTIC BAGS MAKING MACHINE VAMA VC 600 Germany made in 2015. Technical data Manufacturer: VAMA GmbH Model: VC 600 Production year: 2015 Technical parameters The width of the film maximum: 600 mm The maximum length of the bag: 1200 mm Film thickness: 25-80 μm weld Capacity: 60 - 90 bags per minute Rolling rollers 2 with roll diameter: 700 mm Stacking position: 25-50 pieces Machine for the production of plastic bags Excellent condition, located in Poland Cgobjg D Arnevl Dkajt

Condition: used, Bag making machine - Tuber with machine glue. Capacity: 80 pcs/min, possibility of printing in three colors. Cgebvl Dkotvnmrsaot Accessories. 16 rollers for different dimensions of bags; 5 skis for adjusting the width of the bag. Bottom glue - works on the principle of a micro switch, folds the bag and applies the glue by itself.

Condition: excellent (used), Year of construction: 2020, Functionality: fully functional, Description 1)Perfect design, fine assembly, good stability, safety, low noise. 2)Worm gear, worm rod, crankshaft drive technology, die cutting high pressure, long service life. 3)Imported high-precision cam indexing unit, die-cutting high precision, stable performance, stable running. 4)European technology feeding head, sucking paper adjustable, stable, accurate, paper various applicability. 5)Non-stop feeding, pre-coding paper pile and auxiliary paper delivery device, shorten the auxiliary time, improve working efficiency. 6)Die-cutting chase and sole plate structure, user-friendly design, installing and adjusting mold quick and easy. 7)Pneumatic locking chase device, frame fixed more secure, accurate, timesaving. 8)Front lay, side lay and paper delivering device fine adjustment, paper positioning convenient and accurate. 9)Double sheets, crooked sheets, empty sheets photoelectric level control, to ensure accurate and stable paper, reduce waste. 10)Modular electrical control design, the use of imported international famous brand electrical components to ensure accurate control, good reliability. 11)Touch-screen man-machine interface, running real-time dynamic monitoring display, machine adjustment, troubleshooting convenient and quick. 12)Circulation cooling oil supply system to ensure that the machine moving parts with good lubrication, durable. 13)Regular quantitative automatic oil supply system to ensure that other moving parts of the machine fully lubricated, long service life. 14)Equipped with transversal 2 shaft, individual foil feeding system, ensure foil transferring stable, accurate, tension control reliable, when machine running at high speed, less stretch on foil, the feeding difference is only 1mm. 15)(Optional) Stripping function three-frame linkage mechanism, user-friendly design, installing and adjusting the stripping mold quickly and easily. Max. sheet size: 1060×770mm Min. sheet size: 450×370mm Max. die cutting size: 1050×750mm Gripper margin: 8-17mm Paper range: 90-2000g/m2(cardboard)0.1-2mm(cardboard)≤4mm(corrugated) Foil pulling shafts: Transversal 2 Cgobvorq Dhiol Dkast Zones individually heated: 12 heating zones(each zone can be adjusted independently, the highest adjustable temperature is 200℃) Max. foil transversal diameter: ￠250mm Max. cutting force: 300T Max. working speed: 6500s/h Max. stripping speed: 6000s/h Max. delivery pile height: 1200mm Max. feeding pile height: 1350mm Main motor power: 15kw Power rating: 35.6kw Machine weight: 16000kg Air requirement: 0.6Mpa,＞0.37m3/min Overall machine dimension: 6050×4200×2260mm

Condition: excellent (used), SIMPLACUTTER (CAUHE) IV - 1680x1160 Machine little used, in very good condition Equipment: - pneumatic clutch and brake - console Cebeuwru Hsvl Dkajgt - heated plate - 3 modes of operation: single, continuous, with time delay on opening - central lubrication - additional safety guards - working tools - hard pressure plate

Condition: good (used), Case maker Kolbus Model DA36 Minimum size 110 x 155 mm Maximum block size 405 x 560 mm Spine size 8 -80 mm Speed Machine can run 14-15 cases a minute in it´s current condition Cgobvl Dkouauivoast Formats that we do mostly on the machine are A4, A5, B5, B6 The machine can work with paper and PU leather materials. The machine is in operation and can be tested until September 2024, after that we install a new machine so the test will not be possible Location: Serbia

Year of construction: 1996, Condition: good (used), machine/vehicle number: 818, Standard Machine Cgsbjfh It Eevl Dkast Paper Weights Min. : 60 g/m2 Paper Weights Max. : 250 g/m2 Speed : 15.000 pcs/hour Max. Size : 1040 x 740 mm Min. Size : 520 x 450 mm

Condition: excellent (used), SIMPLACUTTER (CAUHE) III - 1480x1070 Machine little used, in very good condition Cgjbvl Dsuwrrrskaot Equipment: - pneumatic clutch and brake - control panel - quick release frame (electric) + additional frame - 3 modes of operation: single, continuous, with time delay on opening - central lubrication - additional safety guards - operating tools - hard plate for pressure

Condition: excellent (used), SIMPLACUTTER (CAUHE) - 1080x770 Machine little used, in very good condition Equipment: - pneumatic clutch and brake - one frame for quick die mounting + two additional frames - 3 modes of operation: single, continuous, with time delay on opening Cgsbvlot Twqws Dkaot - central lubrication - additional safety guards - working tools - hard plate for table + additional