Table shot blaster with turbine, blasting machine

Staněk TZS 1

Condition: good (used), Year of construction: 2008, Pass threw Hook type shotblasting machine 3000x3500 with motorised hook with crane OMSG Year or production: 2008 Type: Hook type Max. diameter of workpiece: 3000 mm Max. height of workpiece: 3500 mm Max. workpiece weight: 10.000 kg Manual blasting chamber: YES Blow off chamber: YES Machine oppening width: Nr. Of turbines: 16 Turbine type: 350 Turbine wheel diameter: 350 Power of turbine: 16x 11kW Max. turbine flow: Guedpfozubb Nex Anwei Type of transport rail: I Cleaner type: airwash Foundation: YES Housing protection: Mn+ rubber Filter: YES Installed power: 241 kW

Condition: new, Year of construction: 2025, functionality: fully functional, pressure: 6 bar, compressed air connection: 6 bar, operating pressure: 6 bar, warranty duration: 12 months, overall weight: 8,000 kg, inner dimension height: 600 mm, workpiece weight (max.): 20 kg, turntable diameter: 400 mm, The described shot blasting machine is designed for the automatic blasting or peening with selected media shots in accordance to the final finishing result to achieve. Part to be blasted will be positioned on suitable pieces’ holders that minimized the shadowing of the contact areas parts/jigs. The parts are inserted and extracted by an automatic cycle into the blasting/peening zones, by means of a step-by-step conveyor that can also operate in continuous mode. The parts, after passing through a neutral zone, are blasted / peened in the subsequent zones, prior unloading the parts are also blown. The system is equipped with one (1) loading/unloading position to allow easier loading/unloading during the process cycle Once the piece has been loaded with operator or automation, the cycle starts and the conveyor process a step forward, allows the newly loaded piece to enter the cabin and the simultaneous arrival of an already processed part at the unloading station. Gjdpowdgrzjfx Anwjui The machine works with masked times, therefore all the positions of the satellites equipping the conveyor are occupied in the cycle time, when fully operational. In the inner positions of the cabin the satellites rotate, and the shooting guns jets the blasting/peening media with a correct impact angle as from appropiate design.

Condition: new, Year of construction: 2023, total length: 3,700 mm, • 8x Batterie, 215-260AH • 1x Steckdose im Korb • FI-Schalter • Generator • eingebautes Ladegerät • Maximaler Bodenauflagedruck 14,0 kg/cm2 • Fahrgeschwindigkeit – abgesenkt 6,0 km/h • Wenderadius – außen 2,60m • Wenderadius – innen 0,75m • Steigfähigkeit 30% • Arbeitshöhe 12,65m • Arbeitsbereich (Standard-Plattform) 6,05m • Knickpunkthöhe 7,12m • Schwenken (nicht Endlos-Drehung) 345° • Plattformtragfähigkeit 1 200 kg • Korbarm – Gesamtlänge 4,14m • Korbarm – vertikaler Arbeitsbereich 120° (+60° / −60°) • Hintereinstieg mit Schieberiegel • Voll proportionaler Joystick für Fahr- und Hubbewegung mit integrierter Wippe zur Daumenlenkung • 2 Mini-Joysticks ermöglichen eine proportionale Steuerung der Hub- und Senkbewegungen von Mast und Korbarm • 4,14 m Gelenkausleger • Funktionsaktivierung mit vergrößertem LCD-Statusdisplay • Lastüberwachungssystem • Wechselstromanschluss im Arbeitskorb • Große Werkzeugablage • Direkter, elektrischer Zweiradantrieb • Bürstenlose Wechselstrom-Antriebsmotoren • Schnellere Batterieaufladung • Automatische Stromsparfunktion bei Stillstand • Funktionsdrosselung bei Tiefentladung • Bordeigenes Diagnosesystem mit integriertem Display • Automatische Hinterradbremsen • Gewölbte Schutzhauben aus Polyester • Motorbetriebenes Schwenken der Plattform • Hochleistungsfähiger Stahlrollen- Hubmast, um 345° schwenkbar • Kettendurchhangerkennung • 3° Neigungsalarm mit Warnleuchte • Rahmenbreite 1,20 m • Hebe- und Zurr-Ösen • Schlüsselgesicherter Wahlschalter für Bodensteuerung • Batteriestandsanzeige • Betriebsstundenzähler • Hupe • Fahrausrichtungssystem • Gurtzeug-Ösen Gsdpfxszwx Ncs Anwjui • Xenon-Rundumleuchte • Manuelle Notabsenkung • Passive Lochfahrschutz • Bereifung (abriebfest) 457 x 178mm • Elektrisches System 48V Gleichstrom • Batterien (tiefentladbar) 4 x 48 V – 260 Ah • Batterieladegerät Im Fahrzeug, 110 V / 230 V HF • Antriebsmotoren 2 Wechselstrommotoren • Elektrischer (Pumpen-)Motor 3,5 kW, 48 V Gleichstrom • Hydrauliksystem Hydraulikbehälter 15 l

Condition: new, Year of construction: 2026, functionality: fully functional, operating pressure: 6 bar, inner dimension width: 600 mm, inner dimension height: 400 mm, volume flow: 10,500 m³/h, Equipment: documentation/manual, New Wire Mesh Belt Shot Blasting Machine RB-600 AH 4 Description: The RB-600 AH 4 wire mesh belt shot blasting machine from ABRAZIV Kft. is designed for the economical and continuous surface treatment of small to medium-sized workpieces. The machine is suitable for descaling, derusting, cleaning, and surface preparation of aluminum and steel castings, forgings, and workpieces that cannot be shot blasted in bulk. The machine is manufactured to order and can be configured individually according to customer requirements. The RB-600 AH 4 is equipped with four ABR-380 shot blasting turbines. Two turbines are located above and two below the wire mesh conveyor belt. This arrangement ensures optimal coverage of the cross-section and a uniform blasting result. The turbines operate at an angle of approximately 70° to the direction of travel and have eight blasting blades and a pre-accelerator. The active blasting area is lined with highly wear-resistant manganese steel. Other internal areas are protected by wear-resistant, noise-reducing rubber. The wire mesh belt is made of highly wear-resistant spring steel. A closed blasting media circuit with a screw conveyor, bucket elevator, blasting media cleaning system, and dosing system ensures reliable operation. Three-layer rubber curtains reduce blasting media leakage. An adjustable high-pressure blow-off system cleans the workpieces after the blasting process. The extraction and filter system with cartridge filters achieves a dust emission of max. 3 mg/m³. Technical Data Passage Passage width: 600 mm Max. workpiece height: 400 mm Min. workpiece length: approx. 1,000 mm Shot Blasting Turbines Number: 4 Type: ABR-380 Turbine diameter: 380 mm Speed: 2,800 1/min Blasting media output per turbine: 120 kg/min Wire Mesh Conveyor Belt Load capacity: 500 kg/m Speed: 0–4 m/min Power Consumption Base machine: 45.5 kW Cartridge filter: 7.5 kW Compressed air: min. 6 bar Compressed air consumption filter: 12.5 m³/h Other Data Blasting media capacity: approx. 1,000 kg Blasting media grain size: 0.4–1.2 mm Extraction capacity: 10,500 m³/h Filter area: 252 m² Dust emission: max. 3 mg/m³ Gedpfx Anjzkivtowoui Electrical Data Mains voltage: 3 × 400 V Control voltage: 220 V Frequency: 50 Hz Optional accessories available Magnetic drum separator Frequency converter Automatic blasting media dosing Special paint finish Transport Assembly Commissioning Operator training Spare parts supply Maintenance and service Applications Aluminum and steel castings Forgings Small steel components Single and series components Descaling Derusting Cleaning Surface preparation Location / Production Lichtenfels (Germany) / Kecskemét (Hungary) As a manufacturer, we produce shot blasting machines individually according to customer requirements. Other sizes and special designs are available. We will be happy to provide you with a non-binding offer. Price on request

Condition: new, Year of construction: 2026, functionality: fully functional, pressure: 6 bar, compressed air connection: 6 bar, operating pressure: 6 bar, inner dimension width: 1,500 mm, inner dimension height: 450 mm, input voltage: 380 V, volume flow: 6,000 m³/h, tank capacity: 2,000 l, air pressure: 6 bar, Equipment: documentation/manual, New Conveyor Blast Machine RB-1650 Description: The RB-1650 conveyor blast machine from ABRAZIV Kft. has been developed for the economical surface treatment of steel sheets, profiles, tubes, and welded structures, and is ideally suited for descaling, derusting, cleaning, and roughening steel surfaces. The machine is manufactured to order and can be individually configured according to customer requirements. The RB-1650 is equipped with four high-performance ABR-400 blasting turbines. Two turbines are arranged above and two below the conveyor, ensuring optimal coverage of the cross-section and uniform blasting results. The inner surfaces of the blasting chamber are lined with highly wear-resistant manganese steel. Other areas are protected by wear-resistant rubber, which also reduces noise levels. A closed blasting media circuit with screw conveyor, bucket elevator, blasting media cleaning, and dosing system ensures reliable and economical operation. All functions of the machine are operated via a central control system. In addition to automatic operation, a manual mode is also available for maintenance work. Technical Data Passage Passage width: 1,650 mm Min. workpiece length: approx. 1,500 mm Max. workpiece height: 450 mm Blasting Turbines Number: 4 Type: ABR-400 Turbine diameter: 400 mm Speed: 2,600 1/min Blasting media output per turbine: 130 kg/min Conveyor Load capacity: 1,300 kg/m Speed range: 0–4 m/min Power Requirements Base machine: 44 kW Cartridge filter: 7.5 kW Compressed air: min. 6 bar Compressed air consumption (filter): 3.2 l/min Compressed air tank (filter): 250 l Other Data Blasting media capacity: 2,000 kg Recommended blasting media grain size: 0.4–1.2 mm Extraction capacity: 6,000 m³/h Mains voltage: 3 × 380 V Control voltage: 220 V Frequency: 50 Hz Optional Extras Frequency inverter Extended conveyors Automatic height scanning Automatic blasting media dosing Special coating Transport Assembly Commissioning Operator training Spare parts supply Maintenance and service Application Areas The RB-1650 is particularly suitable for: Steel sheets Steel profiles Tubes Hollow profiles Welded structures Steel construction Machine construction Tank construction Contract blasting operations Location / Production Guedpezidykjfx Anwji Lichtenfels (Germany) / Kecskemét (Hungary) As a manufacturer, we develop and produce our conveyor blast machines individually according to customer requirements. We will be happy to advise you on the design of the appropriate machine and provide you with a non-binding offer. Price Price on request.

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, total width: 1,325 mm, total height: 3,250 mm, total length: 3,735 mm, overall weight: 5,000 kg, We offer a table-type shot blasting machine – Škoda TMSO 2.4/5. Gusdpfx Aoz Dfuvjnwji The machine has 2 rotating tables with a diameter of 1000 mm. It features one turbine with a power input of 7.5 kW. The machine is in excellent condition, fully functional, and can be tested in operation.