Baler

Presto GmbH & Co. KG HPK 50 B

Condition: used, Year of construction: 1988, operating hours: 1 h, machine/vehicle number: V 516, total width: 2,000 mm, total length: 7,000 mm, total height: 1,800 mm, operating pressure: 300 bar, pressing force: 90 t, sheet thickness aluminum (max.): 5 mm, power: 11 kW (14.96 HP), empty load weight: 16,000 kg, cutting force: 90 t, year of last overhaul: 2025, Bale size 400x400 mm Force 1 Step 900 KN Force 2 Step 900 KN Steel max. 2500-3500 Kg/Std. Aluminium max. 2000 - 3000 Kg/Std. Driving Power 11 KW Fodpslhqd Rsfx Ad Aepr Arrangement Surface 7x2x2,5 m x m Machine weight 16 to Place: Austria Aviable: 30.01.2025

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Fpsdpfx Adovgrh Us Ajr Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: excellent (used), functionality: fully functional, Technical data for the document shredding system: Manufacturer HSM GmbH + Co KG General data for the two-stage shredder system: Type Duo Shredder 5750 Year of manufacture 2015 Operating hours 3,093 hours Throughput capacity up to 800 kg/hour, depending on material Rated power 30 kW Rated current 62 A Particle cutting size 6 x 40 - 53 mm Fuse protection 63 A gG/gL/C/K Weight of shredder approx. 2500 kg Data on the pre-shredder: Shredder type V 570 Working width of the cutting unit 500 mm Particle size 20 x 155 mm (w x l) Nominal power of pre-shredder 2 x 5.5 kW Nominal current of pre-shredder 2 x 11.5 A Data on the secondary shredder: Shredder type P 500.2 Working width of the cutting unit 500 mm Particle size 6 x 40 – 53 mm (w x l) Nominal power of secondary shredder 9.2 kW Nominal current of secondary shredder 18 A Security level according to DIN 66399 P-3, O-2, T-3, E-2 Baling press data: Type KP 100.1 Year of manufacture 2015 Operating hours 2,377 hours Pressing force 9 - 12 t Bale weight 40 – 150 kg/bale, depending on material Cycle time 7–16 seconds Feed chute dimensions 450 x 580 mm Bale size 630 x 500 x 400-1000 mm (w x h x l) Triple horizontal binding Press dimensions 3990 x 2225 x 1735 mm (l x w x h) Weight of press approx. 1000 kg Dimensions of entire system, conveyor belt, shredder and press: Fpedewrybrjpfx Ad Asr 9560 x 2071 x 3550 mm (l x w x h) Function description: This is a complete system consisting of a feed conveyor belt, a two-stage shredder and a horizontal baling pres. The material is fed onto the conveyor belt, shredded in two stages and then pressed into stackable bales. A second cutting unit and various motors are available as spare parts for the system. Comments: The documentation (Manual, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Fpedjvf E Avjpfx Ad Aor Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: excellent (used), Year of construction: 2006, operating hours: 2,632 h, functionality: fully functional, machine/vehicle number: 29.381, pressing force: 35 t, filling opening width: 620 mm, filling opening length: 1,000 mm, total width: 2,380 mm, total height: 2,500 mm, total length: 6,625 mm, Including feed belt. The machine is immediately ready for operation. Fpjdsvaw T Aepfx Ad Aor

Condition: good (used), Year of construction: 2006, operating hours: 1,522 h, Manufacturer: Husmann Typ: SPB 22 SEN-E Fsdpjxbpr Ajfx Ad Ajpr Build in: 2006 Volume: 22m3 Back door: top hingend Lifting system: hook at the front

Condition: used, mileage: 325,000 km, Year of construction: 2016, 3-axle 6x4 truck, classifiable as a work vehicle, equipped with a TAM T25-56 series hook lift system, LIV L170Z96 series crane, year 2018, with hydraulic clamp, automatic transmission, retarder, towable, Euro 6 standard. Fpodpfx Aswmfqujd Asr N.B. Please note that the vehicle description is to be considered indicative and may contain errors or inaccuracies. We therefore invite you to contact us to verify the exact correspondence of the data.

Condition: used, Year of construction: 2005, functionality: fully functional, power: 5.5 kW (7.48 HP), input voltage: 400 V, Press container Husmann, with big feeding opening Fjdpfx Aswampfod Aspr

Condition: used, Year of construction: 2018, operating hours: 157 h, load capacity: 450 kg, empty load weight: 2,528 kg, construction height: 2,350 mm, fuel type: electric, total length: 2,390 mm, drive type: Elektro, construction width: 1,150 mm, Scissor lift Fpodpfx Asnk Unaod Ajr

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, functionality: limited functionality, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale width: 1,100 mm, bale height: 750 mm, power: 15 kW (20.39 HP), empty load weight: 4,000 kg, volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Fpodpfx Adju Thh Es Aor Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating ins3.641tructions, CE, electrical and hydraulic circuit diagram) is available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.