Used Gesan Dps 200 for sale (15,987)

Condition: excellent (used), CTS Type: TSS-70/130 Water-cooled refrigeration unit For sale is a high-quality thermal shock test chamber by CTS (Clima Temperatur Systeme), model TSS-70/130. This device is designed for performing thermal shock tests and is typically used in industry, research, and quality assurance. Application Areas: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical Specifications: Type: TSS-70/130 Test volume: 130 liters Temperature range: - Hot chamber: +50°C to +200°C - Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from ambient temperature to +180°C Cooling rate: approx. 4 K/min from ambient temperature to -60°C Temperature deviation: - ±1 K over time - ±2 K spatially Temperature change rate: - max. 100 K/min average for shock test mode (no radiant heat) Transfer time between chambers: - ≤ 15 min for -65°C to +200°C with 10 kg ICs Changeover time: - < 10 seconds Electrical Specifications: Connection: 400 V, 3/N, 50 Hz Nominal power: approx. 17.2 kW Nominal current: approx. 29 A Site fuse: 32 A slow-blow Connection: Cekon 32 Bdjdpfx Asy Hkd Hedqjf Refrigeration System: Refrigerant: R404A / R23 Water-cooled, low noise, fully hermetic Features/Equipment: - CTS control panel - Microprocessor-controlled regulation and monitoring system - Programmable operation (up to 100 test programs) - Digital setpoint and actual value display - RS232 interface - 2 free switching channels for external device control - Fault notification via volt-free contact (Loadable up to 30 V DC, 2 A) - EMC tested Technical Construction: - Hot and cold chambers - Transfer basket with spindle drive - Test chamber/transfer basket made of stainless steel (material no. 1.4301) - Stainless steel wire insert basket - Tube port NW 50 with sealing plug - Compressed air connection 1/4" male - Non-pressurized condensate drain R 1/2" female thread - Safety door locking - Lockable door with window Dimensions (according to installation diagram): External dimensions approx.: 2335 x 940 x 1820 mm Installation clearance approx.: 1990 x 940 x 1652 mm Test chamber internal dimensions: height approx. 410 mm, width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Additional Data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh Important information for your safety as a buyer! The following points are performed on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If required, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented test run. Condition: used Scope of delivery: see photos (Specifications subject to change and errors excepted.) For further questions, please feel free to contact us by phone.

Condition: good (used), Year of construction: 2011, ENGEL Victory 200/50tech with integrated Robot Viper 12 Control panel : CC200 Core pull 2-fold - movable clamping plate Hotrunners 16 circuits. Nozzle orifice 12mm Multi-level conveyor belt, ENGEL safety guards for robots. Bdedpfx Aezmg Rmsdqsf Technical Specifications: 1. Machine model: ENGEL VC 200/50 Tech 2. Clamping force: 500 kN (50 tons) 3. Opening stroke: 408 mm 4. Ejector stroke: 100 mm 5. Ejector force: 39.8 kN Injection Unit (30 mm screw): 1. Screw diameter: 30 mm 2. Max. swept volume: 99 cm³ 3. Max. screw speed: 480 rpm 4. Injection rate: 144 cm³/s 5. Increased injection rate: 95 cm³/s 6. Specific injection pressure: 1451 bar 7. Increased specific injection pressure: 2205 bar 8. Nozzle stroke: 230 mm 9. Nozzle contact force: 28.3 kN

Condition: good (used), Year of construction: 2013, Engel Victory 200/50 tech (2013) Technical Specifications: 1. Machine model: ENGEL VC 200/50 Tech 2. Clamping force: 500 kN (50 tons) 3. Opening stroke: 408 mm 4. Ejector stroke: 100 mm Bsdpfx Adszmg Nvsqjdf 5. Ejector force: 39.8 kN Injection Unit (30 mm screw): 1. Screw diameter: 30 mm 2. Max. swept volume: 99 cm³ 3. Max. screw speed: 480 rpm 4. Injection rate: 144 cm³/s 5. Increased injection rate: 95 cm³/s 6. Specific injection pressure: 1451 bar 7. Increased specific injection pressure: 2205 bar 8. Nozzle stroke: 230 mm 9. Nozzle contact force: 28.3 kN Control panel : CC200 Core pull 2-fold - movable clamping plate Hotrunners 16 circuits. Nozzle orifice 12mm Multi-level conveyor belt, ENGEL safety guards for robots.

Condition: excellent (used), Feutron Temperature Test Chamber We are offering a temperature test chamber here. Feutron Temperature Test Chamber, Air-Cooled Nominal test chamber volume: 280 liters Dimensions External dimensions: 1500 x 2040 x 1075 mm With fan motor and door removed: 1500 x 1940 x 925 mm Test chamber interior: 720 x 690 x 560 mm Door, clear opening: 720 x 690 mm Heated viewing window: 500 x 600 mm Temperature range -70°C to +180°C Heating rate: 4.0 K /min Cooling rate: 0.6 K /min Mains connection: 400 V 3/N/PE, AC, 50 Hz Maximum power consumption: 6.3 kW Weight: 600 kg Type: 3416/17 Bjdpoziyggofx Adqjdf Refrigerants: R507 / R23 For your safety as a buyer, please note the following information! The following steps are carried out on all chambers we offer in advance: 1. Functional check and replacement of necessary components 2. Refilling with legally compliant refrigerant 3. After successful inspection, the chambers undergo a test run monitored with calibrated equipment. Condition: used Scope of delivery: (See photo) (Specifications subject to change and errors excepted!) If you have any further questions, we are happy to answer them by phone.

Year of construction: 2026, condition: used, New: Yes Empty weight: 400 kg Dimensions of cargo space: 150 x 130 x 107 cm CE mark: yes Please contact Team DPX for more information AC400V-200kW Automatic Load Bank Rated Voltage: 3P4W AC400V 50/60 Hz Rated Voltage & Frequency: 400VAC; 3 phase 4 wire, 50/60 Hz Bodpfx Ajznr Dbjdqedf Power Supply: 3P5W AC400V 50 Hz Rated Power: 200 kW at 400V Duty Cycle: Continuois Cooling Type: Forced Air Cooling (Horizontal air intake and exhaust cooling, there will be louver at air outlet and inlet.) Load Steps: Resistive Load: 9 steps, 1, 2, 2, 5, 10, 10, 20, 50, 100 kW Wire Connection: - Load bank input— busbar (star coupling “Y”) - Control power input—terminal block Communication Interface: RS232/RS485

Condition: ready for operation (used), Year of construction: 2013, machine/vehicle number: 0-250-17-2346, functionality: fully functional, travel distance X-axis: 4,300 mm, travel distance Y-axis: 2,250 mm, travel distance Z-axis: 300 mm, number of axes: 4, spindle speed (max.): 24,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 4,300 mm Travel range, Y-axis: 2,250 mm Travel range, Z-axis: approx. 300 mm Main spindle Power: 10 kW Bjdpszld Iysfx Adqodf Tool interface: HSK-F63 Spindle speed, max.: 24,000 rpm Axis configuration Controlled CNC axes: 4 Interpolating C-axis Servo-controlled Z-axis Tool changer Number of positions: 14 Tool holder: HSK-F63 Drilling unit Number of drilling spindles: 12, vertical Integrated groove saw Vacuum system Vacuum pumps: 3 x Becker MM1322 AV Total air flow: approx. 300 m³/h MACHINE DETAILS CNC control Version: WoodWOP 6 Beckhoff Industrial PC Beckhoff TwinCAT CNC Bosch Rexroth IndraDrive Digital Servo Drives SERCOS Motion Control Supply voltage: 415 V Frequency: 50 Hz Phases: 3 Full-load current: 61 A Main fuse: 80 A Control voltage: 24 VDC EQUIPMENT Matrix vacuum table 10 vacuum zones Heavy-duty gantry construction Automatic central lubrication system Twin extraction hoods with automatic positioning

Condition: good (used), Year of construction: 2007, functionality: fully functional, load capacity: 200 kg, arm reach: 2,750 mm, controller manufacturer: ABB, controller model: IRC5, teach pendant manufacturer: ABB, teach pendant model: FlexPendant, input voltage: 400 V, Equipment: documentation/manual, For sale: High-capacity industrial robot ABB IRB 6650-200 (Design 2006/2007). • Manufacturer: ABB • Model: IRB 6650-200 / 2.75 • Year of Manufacture: 2007 • Payload: 200 kg | Reach: 2.75 m Bdjdpfxjzqd Eco Adqof • Controller: ABB IRC5 (RW 5, MultiMove, Collision Detection, DeviceNet/Profibus DP) • Included: Manipulator, IRC5 cabinet, FlexPendant (10m), interconnecting cables (15m).

Condition: used, Year of construction: 1984, machine/vehicle number: 106, 4-Spindel-Papierbohrmaschine - 4-head spindle paper drilling Josef Foellmer IRAM 200Year ca. 1984 - Serial-No. 106 Drilling area 3 - 10 mm Drilling distance variabel 36 - 430 mm Online-Video-Inspection by Skype-Video Bodpfx Adsh Axadsqsdf We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Neue Nummerierwerke - New Numbering units Zeisser 100/200 ZAVSome Numbering heads ZEISSER - NEW Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test Bedeh Ax Hxepfx Adqsdf

Condition: used, Year of construction: 1992, Anleger - CMC Einsteckmaschine - Feeder - CMC Inserting machine RITMICA Universal H-200Year 1992 - Serial-No. H-200 2 Feeder for CMC Inserting Machine Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test Bdodpfx Adsh Ax Snjqjf

Condition: used, Year of construction: 2024, operating hours: 47 h, lifting height: 20,000 mm, construction height: 2,740 mm, fuel type: electric, drive type: Elektro, construction width: 2,380 mm, Telescopic boom lift Front tire size: 914 x 381 mm / 36X15D610 Rear tire size: 914 x 381 mm / 36X15D610 Battery voltage: 48V Bjdpovgh S Ajfx Adqjdf Battery capacity: 460Ah Battery condition: 80-100% CE certificate, Image may be for illustration purposes. Exide lead-acid battery with central filling 48V 460Ah, cover for external display, galvanized work platform basket 2.10 m, foam-filled tires 910x370 mm 36x15D610, Secondary Protection System (SPS).

Condition: new, Year of construction: 2022, functionality: fully functional, machine/vehicle number: 0-250-87-6869, Drilling head with 8 spindles (V8 SW/32) Horizontal drilling head with 4 spindles on X Horizontal drilling head with 2 spindles on Y Grooving saw D=100 mm Stopping cylinder for workpiece positioning Bsdpfx Adsvtyc Hsqjdf Workpiece clamping system Workpiece length 2500 mm Workpiece thickness 12-60 mm WOODWOP for machine WOODWOP IMPORT DXF BASIC (1 license)

Condition: used, Year of construction: 1998, turning diameter 200 mm turning length 400 mm control SIEMENS SINUMERIC 840 C total power requirement 40 kW weight of the machine ca. 6.500 kg Bdjdpfxot Hw Rko Adqsf dimensions of the machine ca. m

Condition: used, Year of construction: 1997, max. wheel diameter 215 mm gear width 40,65 mm max. module total power requirement 20 kW weight of the machine ca. 10 t Max. external Ø of workpiece 215 mm Tooth profile, height x width 16 x 40.65 mm No. of teeth 5 - 200 Max. tooth ratio 1 : 10 Grinding wheel Ø 51 - 190 mm Grinding wheel speeds 1,000 - 6,000 rpm X Axis (horizontal) 152 mm Y Axis (vertical) 178 mm Z Axis (slide base plate) 304 mm Distance from middle of machine to middle of workspindle 115 mm Axial speed 125 mm/sec Workpiece speeds 0 - 30 rpm Workspindle bore, conical 3 29/32 inch Total electrical load 20 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features * FANUC CNC Control, Model 150 MB, for 7 axes, with monitor and direct input. Automatic calculation of all workpiece and grinding parameters. Bdodjt Hwxhopfx Adqof * Extensive coolant equipment with filter system, band filter, etc. * Driven grinding wheel dressing device with CNC dressing control for automatic compensation of form and diameter after every dressing. * Gear grinding is effected either in single component operation using a conical cup wheel (Gleason 30°), or with a cylindrical cup wheel. These grinding wheels can be made of CBN, or of traditional "dressable" aluminium oxide material (question of cost). Grinding with a conical grinding wheel is of advantage with regard to heat build-up and quality of tooth contact pattern. Therefore these pairs of bevel gears (for automotive industry) can be generated in high quality with consistent accuracy, economically, and with short set-up times. Condition : Very good - machine can be inspected here under power Delivery : Ex stock, as inspected Payment : Net, after conclusion of contract Thank you for your interest. We always have a good selection of gear machines available. Please let us know what you need.

Year of construction: 1991, condition: used, max. wheel diameter 0 mm max. number of teeth 0 max. module min. module total power requirement kW weight of the machine ca. t Bsdjt Hwv Hepfx Adqjdf dimensions of the machine ca. m CNC controlled milling machine for synchronous rings

Condition: used, Year of construction: 1971, pressure 200 t passage width NA mm stroke 180 mm table length 690 mm table width 530 mm distance between columns 420 mm total power requirement 18 kW weight of the machine ca. t dimensions of the machine ca. m Bedpfx Adjt Hw Dwoqodf Hydr. 4-Pillar Press for Embossing/Calibration

Condition: new, Year of construction: 2026, fuel type: diesel, motor manufacturer: Perkins 1206J-E70TTAG, General information Field of application: Construction Weights Empty weight: 3.651 kg Functional Generator capacity: 200 kVA Dimensions of cargo space: 409 x 142 x 237 cm CE mark: yes Other information Fuel consumption: 32.4 Liter / Hour at 75% Load Generator: FG WILSON LL5114F Frequency: 50 Voltage: 400 Drill equipment: Tank, Battery, Control Panel, Steel canopy Emission level: Stage V / Tier IV final Water tank volume: 822 l Production country: CN Additional information Please contact Team DPX for more information = Additional options and accessories = - Battery Bdedpfxex S Umvo Adqef - Control Panel - Steel canopy - Tank

Condition: new, Year of construction: 2026, fuel type: diesel, motor manufacturer: Perkins 1106A-70TAG3, General information Field of application: Construction Weights Empty weight: 2.058 kg Functional Generator capacity: 200 kVA Dimensions of cargo space: 352 x 133 x 168 cm Bdjdpfx Aow Rutfjdqof CE mark: yes Other information Fuel consumption: 30.7 L/Hour 75% Load Prime Generator: FG Wilson FGL30120 Frequency: 50 Voltage: 400 Drill equipment: Tank, Battery, Control Panel, Steel canopy Water tank volume: 394 l Additional information Please contact Team DPX for more information = Additional options and accessories = - Battery - Control Panel - Steel canopy - Tank

Condition: new, Year of construction: 2026, machine/vehicle number: FGWPEP48ERPC03709, fuel type: diesel, power: 160 kW (217.54 HP), motor manufacturer: Perkins 1106A-70TAG3, General information Field of application: Construction Weights Empty weight: 1.548 kg Functional Generator capacity: 200 kVA Dimensions of cargo space: 251 x 101 x 164 cm CE mark: yes Other information Fuel consumption: 30,7 L/Hour at 75% Load Prime Generator: FG Wilson FGL30120 Frequency: 50 Voltage: 400 Drill equipment: Tank, Battery, Control Panel Water tank volume: 394 l Production country: CN Additional information Please contact Team DPX for more information = Additional options and accessories = - Battery - Control Panel Bdjdpswafzmefx Adqsf - Tank

Condition: used, Year of construction: 2018, CNC-CONTROLLED MACHINING CENTER AUTHOR M 200 AUTHOR M200 3710x1620 Z250 - CNC-controlled machining center 1 Technical data Work area I.M.S. I.U. Work area X-axis 3710 mm * 146" * Work area Y-axis 1620 mm * 63¾" * Workpiece passage Y 1900 mm 74¾" Workpiece passage Z 250 mm 9¾ Workpiece length for pendulum machining 1700 + 1700 mm 67" + 67" Travel speed of the X-Y axes PRO-SPACE 56 m/min 184 ft/min Travel speed of the X-Y axes PRO-SPEED 78 m/min 256 ft/min * Distance covered by all tools in the X and Y direction; see the corresponding layout for further details. With a 5-axis motor, the dimension in Y increases to 1680mm (66"), for motor JQX or 1720mm (67½") for motor KS/KT max. Width of the loadable plate for horizontal drilling, electric spindle only oriented vertically, no central reference stops Installation data I.M.S. I.U. Installed power 23 - 28.5 KVA Electrical standard specifications 400 Voltage 50 Hz 3 phases Air consumption 450 Nl/min Compressed air consumption 4500 m³/h 2650 CFM Extraction air velocity 30 m/sec Extraction nozzle diameter 250 mm 9.8 Inches Noise level VSA * LAV * Drilling 72.2 74.6 Milling 74.3 80.7 Reference standard EN ISO 11202:1995* VSA = unloaded and without extraction * LAV = in operation with extraction Structure of the base body: The CNC machining center can be equipped flexibly with different milling units as well as multi-spindle drilling heads and many other units, up to dowel drilling units. In order to meet all requirements in the field of wood and plastic processing, as well as the demands of the users, each machine can be equipped with 3, 4 or 5 machining axes. The selection of drilling units extends to up to 34 drilling spindles with an integrated groove saw for the back panel groove or rabbet machining. The possibility of using this high-quality CNC machining center both as a cantilever table machine and with an aluminum grid table underscores the flexible range of applications and the performance of the M100 and M200 series. Powerful drilling heads, with individually selectable drilling spindles, max. RPM 8,000, and implemented in . technology, "the most robust drilling spindles on the market", with more than 1,000 maintenance-free application hours (lubrication interval of the drilling spindles). The possibility of being able to replace the drilling spindles within a very short time, "even without a technician", through the technology, without disassembling the drilling gear, sets a benchmark in the industry and is already standard on your machining center. Imagine your CNC machine performing hinge drilling in just one drilling operation (option), instead of the usual 3. An option that underscores our claim to offer you robust and high-performance units on our machines. Ideally and flexibly equipped for a wide variety of requirements. Whether manual or automatic, the FLEX cantilever work table allows vacuum cups and mechanical clamping elements, such as pneumatic clamps for window or curtain wall constructions (option), to be quickly, safely and cost-effectively adjusted to any material and clamping requirements, making your day-to-day work easier. Differently sized vacuum cups and clamping elements, which were developed in close cooperation with customers and users, are available as an option. Bodpfezk E Huex Adqsdf

Condition: ready for operation (used), Year of construction: 2006, Prinzing beading machine Type SME 200/11 Bjdpeh Hgdrofx Adqjdf year of construction 2006 throat 1100 mm connected load 5,5KW max. sheet thickness 1.5 mm VA Siemens Siematic OP7 control Special equipment: -parallel top roller feed with bearing-mounted work rollers -stepless drive motor -motorised top roller feed, infinitely adjustable sensor-controlled feed for automatic operation Table-top version of sheet guide device Total weight 6700 kg The offer is only addressed to dealers in accordance with § 14 of the BGB (German Civil Code). No Sales to private persons

Condition: new, Year of construction: 2007, Storage location number: 100577028 Transport dimensions (L x W x H): 0 x 0 x 0 ---- Location: Passau Bdjdpfjzp T Taex Adqjf Dimensions: 3,750 x 1,450 x 2,180 mm (L x W x H) Weight: 3,644 kg Engine: Volvo TAD740GE Fuel: Diesel Power output: 250 kVA

Condition: excellent (used), CATALOG NUMBER 6650 TECHNICAL DATA - Max cutting height: 200 mm - Track width: 450 mm - Shaft width: 450 mm - Blade bore diameter: 80 mm - Shaft diameter: 60 mm - Min. blade diameter: 250 mm - Max. blade diameter: 350 mm - Max. width of cant: 870 mm - Min. length of cant: 1500 mm From above: - Pawls - Feed shaft, toothed, metal - Pawls - Feed shaft, toothed, metal - Pressure unit - Shaft with saw blades - 2 feed shafts, metal, pneumatically pressed From below: - Guide - Metal sliding roller - Pawls - Track - Shaft with saw blades - Track - Stepless feed speed adjustment via inverter 4-40 m/min - Main motors: 2 x 75 kW - Feed motor: 3 kW - Electric vertical movement of body up/down: 0.55 kW - Electric adjustment of saw blade shafts: 2 x 0.25 kW - Central lubrication - Extraction nozzle diameter: 2 x 300 mm - Dimensions (L/W/H): 3100 x 2600 x 2000 mm - Weight: approx. 6500 kg - Centering device included - Toothed feed rollers: 3 pcs - Smooth feed rollers: 8 pcs - Motor: 2 x 1.5 kW - Pneumatic top pressure - Side pressure - Dimensions (L/W/H): 4850 x 1100 x 1800 mm - Weight: approx. 1000 kg ADVANTAGES – Czech manufacture – Double-shaft design – Centering device – DTR documentation Bdsdpfjza Edajx Adqsf – Year of manufacture: 2010 – Used multi-blade saw, in very good condition Net price: 262,900 PLN Net price: 62,600 EUR Net price calculated at the exchange rate of 4.2 PLN/EUR (in case of significant currency fluctuations, the price may change)

Condition: refurbished (used), Risco 200 litres mixer Product capacity 100 / 150 litres Twin paddle mix arms End door discharge Bdodpfx Ajzmaahodqof Forward and reverse mix arms Refurbished condition

Condition: excellent (used), Year of construction: 2018, Krauss Maffei KM 200-1400 CX with Krauss Maffei LRX Easy Control 100 Robot / Operating hours: 12,000 h in automatic mode Bdedpfx Adszc Nwvjqof Year of manufacture: 2018 Injection Unit: Screw diameter: 60 mm Shot weight: 617 g Injection pressure: 2007 bar Dosage volume: 679 ccm Clamping Unit: Clamping force: 200 t Tie bar distance: 560x560 mm Platen size: 915x915 mm Ejector: hydraulic Clamping unit: hydraulic Control system: MC6 – touchscreen Additional equipment: Very good technical condition Operating hours: 12,000 h in automatic mode Euromap 67 Robot interface Air valve with vacuum measurement x 1 Hydraulic core pull x 3 Pneumatic core pull x 3 Control system for hot runner zones x 10 Hardened injection unit – bimetallic Energy-efficient machine – features a system with 3 variable displacement hydraulic pumps Parallel movements Proportional valve on injection unit – precise injection Machine manufactured in December 2018, delivered to customer in 2019 Krauss Maffei LRX Easy Control 100 Robot Year of manufacture: 2019 4-axis robot: 3 axes driven by servo motors (electric); axis C – pneumatic Touch control panel Safety package for robot Robot with interface, conveyor belt, and safety enclosure Purchase of robot and conveyor belt at additional cost Dimensions: Weight: 11,500 kg Length/Width/Height: 6.10x2.20x2.30 m All machines offered are started up by our service technicians before sale. It is possible to receive a video of the technical tests for the selected machine, or to participate in live technical demonstrations at our premises in Łódź. Price: Upon request