Parts cutter - for doors

Condition: ready for operation (used), functionality: fully functional, shovel volume: 1.2 m³, Year of construction: 2017, operating hours: 1,650 h, Equipment: pallet forks, TECHNICAL DETAILS Earthmoving bucket volume: 1.2 m³ 4-in-1 bucket volume: 0.7 m³ Clamshell bucket width: 250 cm MACHINE DETAILS Maximum speed: 40 km/h Hedpfxozylz Do Ackefl Operating hours: 1,650 h EQUIPMENT Pronar 2600 dozer blade, two-piece, fully hydraulic Pallet fork Note: The wheel loader has been reclassified as an agricultural towing vehicle up to 3.5 tons. A tested tow hitch and trailer socket have been installed for this purpose. This allows for the possibility of applying for a green license plate.

Condition: used, Year of construction: 2016, Angular panel saw with automatic pre-loading and twin pusher system for optimised cutting Osi Plus Numerical Control Os Labelling labelling machine with on-board graphic labelling with part drawings Label printing management software Optiplanning Cutting Optimizer Cutting length mm 4500 Cutting width mm 2200 Blade projection 95 mm Motorized rollers for lateral loading on lifting table 4500 x 2200 mm. The translation speed is 10.8 m\min (50hz) - 13.1 m\min (60hz) Automatic recognition of the lost panel (martyr panel) based on the thickness specified in the machine data Low battery stop Automatic side loading buffer. Includes: perimeter nets, double photocell, push-button panel, predisposition electric for the two motorized pre-rollers and the amplification of 4 rollers in place of the fork passages in the pre- intermediate roller conveyor Pre-loading side roller conveyor dim 3800 x 2200 mm with motorized rollers (height from the ground 325 mm) Inertial conveyor for conveying longitudinal trimmings for angular systems 4500 mm (total length 7295 mm) 3000 mm extension to the inertial conveyor to also convey transverse trimmings Long chute for manual conveying of cross-cut trimmings to the centralized inertial conveyor Hsdsuc Idxspfx Ackofl 2050 x 850 mm air curtain discharge table with wheels at the front Air generator up to 6 floors with air curtain MULTIPUSHER 2.4 system with automatic lubrication Additional mobile lateral aligner on the transverse plane. The presence of this device allows to reduce from 1830 to 1220 mm is the minimum length of the panels that must be sent for cross-sectioning. Automatic blade shaft bending detection device for angular systems (longitudinal and transversal) consisting of a sensor that detects the deflection directly on the blade shaft and a device that detects the revolutions blade directly on the spindle. Remote cycle start button panel Automatic panel loading via rear lifting table Automatic double aligner with pneumatic cylinders Additional movable lateral aligner on the transverse plane Main blade, max diameter mm, KW 15 Scoring blade, max diameter mm, KW 2.2 Blade carriage speed 1-140 m/min. – BRUSHLESS motors Longitudinal pusher carriage speed 90 m/min. Cross pusher carriage speed 135 m/min. Double pusher carriage with 6 grippers on the longitudinal carriage + 10 grippers on the transverse carriage (8 fixed grippers + 2 on the multi-push system) Cutting system for thin panels

Condition: used, Year of construction: 2017, operating hours: 1,113 h, machine/vehicle number: G30XL320839, The machine would be serviced by Zünd Spain! TECHNICAL DETAILS Zünd G3 XL-3200 Plotter Vacuum system: 1–9 kW Tool heads Universal tool head UM-ZS G3, working width: 60 mm Universal tool head UM-ZP G3, working width: 60 mm Operating hours: 1,113 h Hfsdpfx Acezyktljkel EQUIPMENT Zünd G3 XL-3200 Plotter, item no. 6343200 G3 Vacuum system, CIC, item no. 6438104 ICC camera for S3/G3, item no. 6539101 UM-ZS G3 Universal tool head, item no. 6531006 UM-ZP G3 Universal tool head, item no. 6531007 Universal cutting tool (UCT), item no. 6532001 EOT-250 Oscillating tool, G3, item no. 6532018 V-CUT tool, G3, item no. 6532021 Creasing tool type 1 (CTT1), item no. 6532051 Creasing tool type 3 (CTT3), item no. 6532053 Zünd Cut Center software package, item no. 6731200 Zünd Cut Center camera option, item no. 6731250 Zünd Cut Center V-Cut option, item no. 6731240 PC and monitor for Zünd Shipping costs for the plotter

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, overall weight: 3,500 kg, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Cutting range at 90° (round): 530 mm Cutting range at 90° (flat): 530 × 800 mm Cutting range at 45° (flat): 530 × 520 mm Cutting range at 30° (flat): 530 × 320 mm Cutting angle: 45° - 0° - 60° Blade speed: 20–120 m/min Feed length: 1,500 mm MACHINE DETAILS Saw motor power: 3.0 kW Coolant pump: 100 W Hydraulic pump: 370 W Power connection: 400 V / 50–60 Hz Dimensions & Weight Dimensions (L × W × H): 2,500 × 4,000 × 2,500 mm Total weight: 3,500 kg Hfodpfxszyccxs Ackol EQUIPMENT Machine stand with chip collection tray Hydraulic cutting pressure control Stepless blade speed control Hydraulic guide arm adjustment Minimum quantity lubrication Automatic shutdown at the end of the cut Chip brush Hydraulic miter adjustment Hydraulic clamping device Hydraulic blade tensioning Operating manual

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: 2018/219, hole diameter: 75 mm, number of planer blades: 6, operating speed: 6 mm/s, year of last overhaul: 2018, For sale is a very fast and complete Cambio debarking system! In 2018, the machine was completely overhauled, and since then, it has been professionally maintained and equipped with a new knife ring with 6 cutting knives! The system can be directly integrated into your existing mechanization! TECHNICAL DETAILS Maximum log diameter: Ø 750 mm Minimum log diameter: 11 cm Shortest log length without an additional feed system: 3 m Shortest log length with an additional feed system: 1.5 m Maximum feed speed: 100 m/min MACHINE DETAILS Rotor motor: 55 kW Feed motor: 11 kW Hydraulic power: 1.5 kW Rotor speed: 220 rpm at 50 Hz Rotor opening: 80 cm Debarking rotor: 6-knife rotor Weight: 10,500 kg Hfedpfx Acozx Eaqokel EQUIPMENT Complete infeed system Complete outfeed system Electrical system Hydraulics for the infeed rollers New 6-knife rotor from the 2018 overhaul Complete debarking system for integration into an existing mechanization Centering device ZV – 75/2 MA Number of horizontal conical rollers: 2 Drive power per SEW worm gear motor: 1.5 kW EQUIPMENT 2 horizontal conical rollers mounted in pneumatically actuated swivel arms SEW worm gear motors with torque supports in a solid steel design Heavy-duty inlet hopper Complete sensor system Outfeed system AW 800 Drive power: 3.0 kW EQUIPMENT Drive via SEW spur gear motor Machine frame made of welded rectangular tubes for supporting additional machine components Hydraulic shock absorbers

Condition: ready for operation (used), Year of construction: 2010, machine/vehicle number: 0-240-06-8502, functionality: fully functional, power: 18 kW (24.47 HP), cutting height (max.): 95 mm, saw blade diameter: 380 mm, cutting length (max.): 4,300 mm, plate width: 2,200 mm, TECHNICAL DETAILS Cutting length: 4,300 mm Panel width: 2,200 mm Saw blade overhang: 95 mm Main saw blade diameter: max. Ø 380 mm Saw carriage feed rate: up to 150 m/min Clamping jaws: 7 pieces MACHINE DETAILS Main saw motor power: 18 kW Scoring saw motor power: 2.2 kW Operating hours: approx. 38,544 h (as of 05.10.2023) EQUIPMENT Automatic rear panel loading system Lift table loading system Lift table Automatic program slider with clamping jaw feed Main saw unit Scoring unit Automatic cutting length and positioning control Angle and back stop Hsdpfjzx Anxjx Ackjfl Air cushion support tables in the operator area CADmatic operating and optimization environment PICA 108 label printer Roller and transport technology in the rear loading area Safety enclosure with protective fencing Dust extraction connections with machine-side dust extraction ducting

Condition: ready for operation (used), Year of construction: 2019, machine/vehicle number: 0-201-08-5142, functionality: fully functional, operating hours: 17,952 h, number of slots in tool magazine: 24, working width: 1,600 mm, spindle motor power: 15 W, number of spindles: 2, working length: 4,760 mm, Machining center with automatic material handling (serial number: 0-205-08-1424) TECHNICAL DETAILS Travel in X-axis: approx. 4,760 mm Travel in Y-axis: approx. 1,600 mm Main spindles: 2 Power of main spindles: 15 kW each Tool interface: HSK F63 Number of drilling heads: 2 Tool changer: 2 × 12-position MACHINE DETAILS Control system: PC85 / woodWOP Operating hours CNC: 17,952 h EQUIPMENT Automatic AP console tables Chip and waste disposal Safety enclosure Hfsdpfxozx Anfe Ackel Associated HOMAG handling and return conveyor system Portal handling Vacuum crossbar Conveyor technology C-axes FLEX-5 preparation Automatically positionable vacuum clamps Liquid ring vacuum pumps Note on machine designation: BOF 712/48/16/AP was the actual historical machine type. CENTATEQ E-500 is the later/current model designation, which is now visible on the machine.

Year of construction: 2008, operating hours: 24,663 h, condition: ready for operation (used), functionality: fully functional, working width: 2,200 mm, machine/vehicle number: 0-241-06-7504, TECHNICAL DETAILS Saw blade overhang: 125 mm Main saw motor: 18 kW Feed rate: 1–150 m/min Max. clamping width: 2,200 mm FEEDING SYSTEM Lift table dimensions: approx. 4,300 × 2,200 mm Lift table load capacity: 7 t Hedpfx Acszxgf Ujkofl MACHINE DETAILS Operating hours: approx. 24,663 h (as of 05.10.2023) EQUIPMENT Automatic panel feeding system Lift table feeding system Longitudinal/cross-cutting unit Roller conveyor and transport system

Condition: ready for operation (used), Year of construction: 2013, machine/vehicle number: 08450, functionality: fully functional, operating hours: 15,861 h, Edge banding machine + BARBARIC LX U4 B2200 return system! The machine is equipped with the following units: Joint milling VTG gluing unit Quick-Lock glue application Pre-melting tank with automatic granule feed Cutting unit Flush/profile milling KFA-x30 contour milling unit Profile and joint drawing blades TECHNICAL DETAILS Workpiece thickness: 8–60 mm Feed rate: approx. 6–30 m/min MACHINE DETAILS Power supply: 3 N PE Operating voltage: 400 V Power frequency: 50 Hz Rated power: 32 kW Rated current: 69 A Operating hours of edge banding machine: approx. 15,861 h (as of 2023) BARBARIC LX U4 B2200 return system Year of manufacture: 2014 Hjdezxgfzepfx Ackofl Serial No.: 2130742-102 Operating hours: approx. 8,997 h (as of 2023) EQUIPMENT Automatic 12-position edge magazine Pre-melting tank with automatic granule feed

Condition: ready for operation (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 004-2024, total length: 2,250 mm, total width: 950 mm, total height: 1,900 mm, overall weight: 740 kg, power: 6.5 kW (8.84 HP), No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Distance between saw blades: 45 mm Hedpfxszvv Rns Ackjfl MACHINE DETAILS Operating voltage: 400 V Frequency: 50 / 60 Hz Power: 6.5 kW Operating current: 14.5 A Dimensions & Weight Dimensions (L x W x H): 2,250 x 950 x 1,900 mm Machine weight: 740 kg EQUIPMENT Completely made of corrosion-resistant AISI 304 steel Two parallel saw blades Fully mechanized wheels Adjustable speed of the side blade The machine comes from a business liquidation.

Condition: ready for operation (used), Year of construction: 2023, machine/vehicle number: 231458, functionality: fully functional, travel distance X-axis: 3,700 mm, travel distance Y-axis: 2,100 mm, travel distance Z-axis: 370 mm, spindle speed (max.): 6,000 rpm, table load: 800 kg, Note: The auction end date has been postponed to September 16, 2026! TECHNICAL DETAILS Travel range, X-axis: 3,700 mm Travel range, Y-axis: 2,100 mm Travel range, Z-axis: 370 mm Rotation range, C-axis: 0–362° Swivel range, A-axis: 0–90° Travel time, C-axis (0–392°): 3 s Travel time, A-axis (0–90°): 2 s Spindle speed, electric spindle: 6,000 rpm Power, electric spindle: 16.5/56 kW Speed, X-axis: 30 m/min Speed, Y-axis: 30 m/min Speed, Z-axis: 5 m/min Dimensions, tilting table: 3,500 × 2,000 + 500 mm Load capacity: 800 kg MACHINE DETAILS Stainless steel cover for saw blade with opening for cutter: Ø 425 mm Stainless steel cover for saw blade: Ø 625 mm Total power consumption: 23 kW Water consumption for saw blade: 30 L/min Total weight: 4,800 kg EQUIPMENT Material and saw blade measuring system Vacuum system for moving the panels Camera with software for management Pneumatic tilting table Motorized rotary head (C-axis) Hjdpfszuyryjx Ackofl Motorized saw blade tilt (A-axis) Stainless steel cover for saw blade with opening for cutter Stainless steel cover for saw blade