Complete sawmill (stationary)

BONGIOANNI CML/M

Condition: good (used), Bandsaw line for big logs 1. Log conveyor 2. Buffering log deck and one piece feeder 3. Log conveyor and centering infeed with turner 4. Söderhamn AKE 245A Twin reducer bandsaw (ARI 6 knife heads) 5. Board separator with block turner 6. Side transfer of blocks 7. Block infeed 8. ARI BKR-600 9. ARI DS-75 multi rip saw 10. Edging line with ARI KT-52 Edger Price: 2 100 000 SEK, in existing condition on site. Line is complete but not all conveyor in bottom floor. Bruks 1503M chipper. No power on electric cabinets (no PLC software) Bedpfxjikvlij Ac Nelc Can be dismantled and loaded by UJ Trading AB Sawmill is located in Sweden.

Condition: used, Chipping roundwood: 100-150 m3/h Bodpfxohclffe Ac Nslc Chipping small waste: 50-100 m3/h Weight: 3165 kg Max log diameter: 254 mm Söderhamn Eriksson 670-56 CC chipper with electric motor. Söderhamn Eriksson 670-56 chipper is intended for the production of chips for pulp, fibreboard and chipboard manufacture. Both roundwood and sawmill waste may be used as raw material. Chipper 670-56 feed is horizontal, at an angle of 37,5 grades to the grain. The chips, of consistent high quality, may be discharged at the bottom or blown straight upwards. Be one of those woodworking companies that wisely manage the resources available to them.

Condition: used, mileage: 69 km, first registration: 08/2023, fuel type: diesel, axle configuration: > 3 axles, gearing type: automatic, emission class: euro6, loading space volume: 10 m³, Year of construction: 2023, operating hours: 8 h, machine/vehicle number: EXVAC SE.10, RIVARD suction excavator EXVAC SE.10 !! IMMEDIATELY AVAILABLE !!! RIVARD industrial turbine Detachable suction hose inlet 10.5 m³ container volume 4-joint boom Hydrostatic drive Filter cleaning Rear / front fall protection Bodpfxog Dl Are Ac Nolc Camera route monitoring

Condition: excellent (used), Year of construction: 2015, Stravis sawmill line with Jabłoński automatic edger after complete renovation. Condition like new. The line consists of: 1. Log conveyor for 5m logs with a cascade feeder 2. Caterpillar-chain saw 110 + 90 kW Blodpfx Aev Iyhfsc Noc 3. Multi-blade saw (2 x 75 kW) spindle diameter 80mm 4. Roller conveyor l- 6m with a mechanism for stopping the movement of the left prism 5. Crosscut saw from 0.8 m to 5m 6. Base conveyor 7. Roller conveyor l=3.5m 8. Driven roller conveyor 4.5m 9. Driven roller conveyor l=4.0 m with a board dumping mechanism 10. Transverse belt conveyor b=3m, l=5m 11. Transverse belt conveyor with a pick-up b=2m, l=5m 12. Longitudinal belt conveyor b=0.4m, l=5m 13. Automatic edger Jabłoński 14. Gooseneck Jabłoński 15. Cross feeder with a scanner measuring the width of the board 16. Centering for the edger 17 17. Edge separator 18. Crosscutter from 0.8 m to 3.0 m 19. Gooseneck 20. Automatic stacker Jabłoński 21. Non-regenerated crosscutter Jabłoński 22. Bruks chipper with control (you need to make a belt or vibrating gutter) Assembly and start-up at the customer's premises is possible. Possibility of sending videos of the working machine before renovation. Possibility of setting the line in a turn or along the length. Optionally, construction of a base for the line. OPPORTUNITY

Year of construction: 1999, condition: ready for operation (used), Linck EWD pre-cutting group consisting of: - Linck EV 40 infeed table, with 1x pair of turning rollers - EWD FZ 3 (mounted on PF19 frame with guide shafts DM 200mm) 2x drive motors with 75/45kW. 1 pair of pull-out rollers - Centering unit EVW - FR 14 side cutting saw with limit cutter 4 x 50KW + 2x 75kW - Side fabric separating transport - incl. hydraulic unit - without switch cabinets Machine is in very good condition! System can also be overhauled and offered with a new control system! Bedpfxjufr Nde Ac Nelc

Year of construction: 1970, condition: good (used), functionality: fully functional, Stenner RESAW VHL 48 manufacture Stenner UK S/N J2103 year 1970 (original photos coming soon) Principal Dimensions and data: Diameter of saw pulleys: 48"= 1220mm Width of saw pulley face-standard 5" (127mm) Width of saw pulley face-optional 5 1/2" (140mm) Maximum width of saw - standard 5 1/2" (140mm ) Maximum width of saw-optional 6" (150mm)A Minimurn length of saw 25" 8" (782mm) Maximum height of top saw guide above table 28" (710mm) Table height from floor level 31 1/2" ( 800mm 9 Overall height from floor level 9.1" ( 2770mm) Overall width 8.1" (2460mm) Speed of saw pulleys,r.p.m. 8,000 (2440m/min) Horse power range 30 kW Size of fast and loose pulleys 20"x6 1/2" Feed speeds, standard; f.p.m. or m/min. 0-140 (0-42.6m) Shipping Specification : Standard Machine : Net weight, lbs. 3583 kg The VHL 48 is a band resaw of advanced design embodying many new features resulting from a close study of user-operator requirements, and the necessity Blodpfovuhumex Ac Njc to provide fast and accurate sawing coupled with ease of operation, reduced operator fatigue, low maintenance, and increased safety. The design caters fully for these essential factors which contribute to a markedly high level of operating efficiency. The machine is primarily designed for the planning mill and joinery shops. The thin bandsaw gives the machine a high timber recovery rate; the loss due to saw kerf being very low. Compared with a circular radial-arm resaw, the VHL is faster, less wasteful, and uses less power for a given class of work general The VHL is made only as, a left-hand machine, i.e. the saw pulleys run in an anti-clockwise direction when looking in the direction of the feed. The drive is normally arranged to give a saw speed of 8,000 feet permin. (2440m l/min.) Main Drive The main drive is applied to the bottom saw pulley spindle which is prepared for vee belt, flat belt, or flat belt fast and loose pulleys to suit the proposed driving unit. Complete electric motor drives, up to 40 H. P. and for most current supplies can be provided; they include two vee pulleys, set of vee belts, belt guard, motor with slide rails, starter and a master stop button which is fitted to the machine base close to the sawyer's position. horizontal rollers The horizontal rollers are 6" (152mm) diameter and extend the full opening on the fence side and 6" (152mm) beyond the table on the open side; they are normally free-running idle rollers. They can be supplied hydraulically driven as optional equipment, either with the machine or after installation; the rollers are then driven in synchronism with the main feed rolls, by a separate motor. The drive is arranged so that the open-side roller at the outfeed end rotates in the reverse direction to facilitate the return of timber to the sawyer. The roller in front of the saw is moveable sideways to permit rapid saw changing.

Condition: good (used), Weinig Hydromat H23 50mm spindles 6,000 RPM Bottom 15kW jointer ready Right 11kW jointer ready Left 11kW jointer ready Right 11kW jointer ready Left 11kW jointer ready Top 15kw jointer ready Bottom 11 kw jointer ready (straight jointer) + outboard bearing Top 11kw jointer ready (straight jointer) + outboard bearing Bottom 15 kw jointer ready Possible to add additional straight / profile jointers as needed !!! Blsdpfx Aswmw Nvec Njc 15kW feed motor. Automatic lubrication system. Possible to supply with moulder infeed and outfeed as needed. Possible to offer tooling if needed.

Condition: used, No. 3176 Automatic planer and moulder WEINIG Hydromat 1000 Used, year of construction 2007 6 spindles: bottom-right-left-top-top-bottom Electronic feed 6 - 60 m/min Working width 80 - 150 mm Working height 23 - 65 mm Finished slat widths 4 - 15 mm Max. Max. number of slats 16 pieces Slat lengths 400 - 4000 mm 1st spindle horizontal at the bottom Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool flight circle 125 - 180 mm 2nd spindle vertical right Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm 3. spindle vertical left 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm Pressure shoe in front of the spindle, swiveling away, pneumatic roller contact pressure 4. spindle horizontal top 15 kW, 6000 rpm, diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 5. horizontal top spindle as saw spindle Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment travel reduced to 25 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 6. horizontal spindle at the bottom as saw spindle Brake motor 30 kW, 5000 rpm Axial adjustment travel reduced to 25 mm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm All moulder spindles with high-performance bearings Blsdpfx Asu Agh Sec Nec Electronic feed 7.5 kW Adjustment travel of the feed rollers compared to the left-hand spindle, axial 35 mm Shorter roller distance compared to the right-hand spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in the table, lateral pressure roller Automatic waxilite pump / lubricant pump Machine with 4-roller extension, pendulum shafts extended to 200 mm 2 driven, toothed rollers in the outfeed table 2 driven, toothed rollers in the machine table Pressure beam before and after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electrical height adjustment of the upper spindles and the feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transportation and assembly Subject to errors in the description and price Transportation and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: used, Year of construction: 1992, 105 twinband linear pm for upto 300mm round logs 4mtr length, this is a complete round to finish sawing system, breaking round logs down to return and resaw everything to a finished product, high production and minimum waste Bljdpfxem Rhfde Ac Nsc

Condition: excellent (used), Baljer & Zembrod roundwood handling, sorting, transport and sawing vehicle - German production Bsdpfx Acjlimrie Nelc - measuring the length of the wood - automatic cutting cycle TECHNICAL PARAMETERS: - max log diameter 1000 mm - crane reach max 9200 mm - crane working angle 225" - rotating head 360 " - lifting capacity: 2000mm - 2560kg 7240mm - 1680kg 9200mm - 1330kg - dimension of the hauler 6000x2150 mm - hauler with two-sided hydraulic discharge - pump motor power 11 kW - feed motor power 8.6 kW - feed speed 90 m/min HOLTEC FS 121 SAW - log length measurement - working length 1000 mm - hydraulic stroke of the guide - manual and automatic operating mode - log lifting - integrated sawdust extraction 2.2 kW - drum for winding the cord Transport dimensions 12.5x2.4x2.4m weight 12000 kg