Year of construction: 2004, condition: ready for operation (used), A defective flatbed die-cutting machine IMG Klett is available. Chase inner dimensions X/Y: 1630mm/1210mm, max. cutting dimensions X/Y: 1600mm/1180mm, min. sheet dimensions X/Y: 650mm/450mm, max. sheet dimensions X/Y: 1200mm/1620mm, min. sheet thickness: 1mm, max. corrugated board thickness: 8mm, max. plastic corrugated material thickness: 8mm, gripper margin waste area: 9mm-15mm, max. cutting force: 400t, motor power: 22kW. Machine dimensions X/Y/Z: approx. 7550mm/5200mm/2450mm, weight: approx. 32000kg. Documentation available. An on-site inspection is possible. Hfjdpfx Ajyxq Ucef Usg

Condition: used, Frame die-cutter - Swivel frame die-cutter - Flatbed die-cutter - Platen die-cutter - Eccentric press Punch + feed for the use of bandknife punching tools Flatbed die cutter HELMERDING type PSH 25 Com. No. EP 97784 Machine. No. 6073 Year of construction 1998 Compressive force 25 ton. Clearance between the tie rods 700 mm Table surface = installation space 800 x 670 mm Table surface = installation frame width 510 x depth 440 mm, plate thickness 20 mm Plunger surface 800 x 670 mm Hole in the table 490 x 420 mm Plunger stroke 45 mm Ram adjustment travel 10 mm Hodpjdzqmzofx Af Ujfg Installation height = tool height 100 mm Stroke rate up to 250 strokes/min. Motor power 15 kW Mains connection 400 Volt, 50 Hz - Controlled drive for infinitely variable stroke rate - Pneumatic clutch-brake combination - ram compensation cylinder - VOGEL automatic central lubrication system - solid base plate with 4 swinging elements under the machine Space requirement L x W x H approx. 3000 x 2000 x 3000 mm Weight 4.5 tons good condition The machine was formerly used for cutting out cardboard blanks. Ideal for cutting out non-woven fabrics or similar for breathing masks.

Condition: used, Straightening machine, strip straightening device with adjustable LENZE geared motor Straightening machine, strip tensioner was used for cardboard approx. 350 x 1.5 mm Not suitable for use as a classical straightening machine Type 11.712.02.10 Output speed of geared motor: 12 to 72 rpm, stepless Torque: 80 to 40 Nm Hjdodzp U Ajpfx Af Usfg Straightening roller speed: 19 to 115 rpm Straightening roller width: 520 mm Straightening roller diameter: 90 mm Total number of straightening rollers: 4 pcs Motor power: 0.37 kW Power supply: 380 Volt, 50 Hz - Pull roller pair, drive of the lower rubber-coated roller via open gear drive - Speed infinitely adjustable via handwheel on the geared motor - Upper part of the straightening rollers mechanically adjustable - Straightening unit with 3 rollers, one of the rollers is missing (rollers of the straightening unit not driven) - On a sturdy metal base - Straightening machine was used for cardboard approx. 350 x 1.5 mm Space requirement (L x W x H): 630 x 460 x 1060 mm Weight: approx. 160 kg Good condition

Condition: ready for operation (used), machine/vehicle number: 154.1004.094, Professional Neolt Electro Foam Trim Plus 310 horizontal cutting machine for foam board, PVC, cardboard and similar materials. This is a high-quality Italian industrial cutter with a maximum working width of 310 cm, suitable for sign making, printing industry and production environments. Main features: • Manufacturer: Neolt (Italy) • Model: Electro Foam Trim Plus 310 • Working width: 310 cm • Electric cutting system • High precision cutting • Suitable for foam board, PVC, cardboard and similar materials Included accessories • Multiple blade holders: 5 mm, 10 mm, 20 mm and 30 mm • Spare blades included • Original manual • Electrical spare parts (circuit boards etc.)• Additional accessories and components Condition: Machine is in good working condition and fully functional. Cutting accuracy is very good. The main unit is clean and well maintained. Support tables show normal signs of use. Hfodsywpcpopfx Af Ueg Additional information: • Maximum cutting thickness up to 30 mm (depending on blade holder) • Currently equipped with 10 mm blade holder • Mounted on wheels for easy movement • Support tables included Logistics Machine available for immediate pickup. Located in Finland. Loading assistance available. Extra Video available showing cutting operation! Complete set with accessories and spare parts – ready for professional use! Keywords: foam board cutter Neolt cutter electric cutter horizontal cutter foam trim sign making equipment large format cutter

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, working width: 2,700 mm, Kryma SK2800 automatic slotter with vacuum autofeeder, machine have been used very little and is in perfect condition and available anytime. Speed is approx. 2000pcs per hour. Machine can do up to 10m long sheets. Video can be sent upon request. Also available Kryma flat bed roller die cut like new, and Sunthinks SC860 single pass printer with auto feeder. Hfjdpfxjtth Ias Af Uog * We can arrange transport within Europe, and give offer with transport included if of an interest.

Condition: ready for operation (used), Year of construction: 2019, operating hours: 15 h, machine/vehicle number: MP.DBDO-00198, Size 75 x 106 cm, non-stop function in feeder and delivery, integrated fine adjustment of the cutting plate, motorized die-cutting pressure adjustment, simple operating concept. The basic model is already equipped with all functions and equipment required to start production. Short makeready times, high flexibility thanks to an extended range of materials, accommodates smaller die-cutting tools. Machine number: MP.DBDO-00198, Impressions: 15 million. Hjdpfx Afjyhn Uqe Usfg

Condition: used, Automatic Platen Die Cutter Joh. Cietz PRESTO Halbautomatischer Stanztiegel / Automatic Platen Die Cutter Joh. Cietz PRESTO Year 2008 - Serial-No. EP51568 Format 370 x 480mm Weight 1100kgs Included frame and tools Hfodpfx Afjylqd Ae Uog Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: good (used), Roller glue application machine, laminating machine, laminating system, laminating system, layering machine -Manufacturer: Hymmen, glue application machine, layer machine type 36 -Working width: 1300 mm Hsdpfx Aoirnwbsf Uefg -Roll diameter: Ø175 x 1300 mm / Ø235 x 1300 mm / Ø85 x 1300 mm -Individual components: see photos -Dimensions: 2230/1100/H1410 mm -Weight: 1260 kg

Condition: used, Year of construction: 1997, functionality: fully functional, machine/vehicle number: 6878, working width: 1,020 mm, total width: 2,000 mm, total length: 12,000 mm, total height: 3,000 mm, stack height: 840 mm, Laminating machine FK 102 S in very good used condition Sheet size min 30 x 45 cm Sheet size max 102 x 124 cm Feeder: Billhöfer A-20-P Smoothing calender: GK-4-1080 Sheet separator: Achilles BT 4.1 Stacker: Bremser S102A1 Additional equipment: pneumatic side lay by TPM electronic overlap control by PME Hfedoxb Dq Tspfx Af Uog automatic film brake by Achilles film cutting device by TPM spare roller (lamination counterpressure) new, included The machine can laminate using both water-based and thermal films (heating units required) Dismantling/transport/possible customs duties etc. must be organized by the buyer.

Condition: excellent (used), Year of construction: 2007, machine/vehicle number: 705537, infeed width: 660 mm, Maximum sheet size 660 x 1280 mm, Pallet feeder, 4 buckles first unit, First cross knife (8 pages) Second cross knife ( 16 pages) parallel buckle to the first cross knife. SB-46/MP.D Press delivery. Noise hoods, Pump, Technical documentation, Standard tools. Intergrated counter Hedsqgcy Ijpfx Af Uefg

Year of construction: 1998, condition: excellent (used), machine/vehicle number: 66000102, Pallet feeder, Vaculift, Vacubelt, DV Pump, MBO MPC Control, ASP 66 Shingle belt press delivery Machine nr: 66000102 Hsdpfx Afehqhgqo Uefg

Year of construction: 1998, condition: like new (used), Round pile feeder, first folding unit TD78/4-1 4 pockets, second unit TD66/4-2,4 pockets, 3 unit knife Stahl EF63 (1984), SBP 80 press delivery, no pump machine was on in house air supply Hfjdpfed Tnxlex Af Usg

Year of construction: 1991, condition: excellent (used), machine/vehicle number: 61861201, Flatpile, Vaculift, Vacubelt, DV Pump, Shingle belt delivery, MCC1 counter Hedjhqhg Aopfx Af Uofg Machine nr: 61861201

Year of construction: 1999, condition: reconditioned (used), Machine is currently undergoing overhaul PROCESSABLE MATERIALS Hfedpfeyuuzdjx Af Usg Depending on material properties and sheet configuration: · Paper with a minimum grammage of 80 gsm · Cardboard or solid board up to a grammage of 2,000 gsm · Corrugated board up to a total thickness of 4 mm (max. sheet curvature 4%) PERFORMANCE DATA Max. sheet format: 820 x 1,130 mm Min. sheet format: 350 x 400 mm Max. cutting force: (400 t) 4.0 MN Max. machine speed: 9,000 sheets/h Standard equipment of the machine: Feeder Non-stop high-performance sheet feeder W3 equipped with: • Automatic non-stop device • Automatic pallet changeover • Suction head • Double-sheet detector • Motorized stack side correction • Motorized suction head adjustment • Conveyor table with pneumatic cover frame • Compressed air and vacuum pump Register Table • Operator-side side lay, switchable between pull and push mode • Light sensor for accurate side alignment of sheets • Fine adjustment of the side lay • Two active front lays with light sensor for register control • Two inactive front lays for sheet stabilization • Separate fine adjustment of gripper edge for drive and operator side • LED display for accurate front and side lay registration • Trend display for sheet detection • Sheet rejection, disabling only the feeder • Height-adjustable top lay for positive sheet guidance Die-cutting station • Roller-guided support rails for the chase • Roller guide for die-cutting plate on swing-out support arms • Motorized die pressure adjustment • Automatic device for lifting the chase to the platen • Electronic die-cutting force display with max. pressure limitation • Vacuum device in sub-table for thin cutting plates Stripping Unit • Frame drive and frame lift for upper tool frame • Mount for the stripping board with centerline fine adjustment • Device for sample sheet removal • Upper tool frame • Lower tool frame Delivery • Fully automatic pile stacker, pre-selectable • Counted sub-stacks with automatic insertion of uncut sheets • Can form sub-stacks (interleaved sheets between 250 gsm – 800 gsm) • Frame lift for upper tool frame • Mount for change frames with electric adjustment in running direction • Pneumatic frame locking • Switchable gripper opener cam and sheet ejector • Sheet jogging device • Integrated conveyor belt for gripper edge or waste grid removal (double-cut) • Separator sheet magazine with electronic level control, refillable from B-side during production • Tool frame with centerline • Change frame for standard pile delivery / gripper edge removal • Change frame for blank separation grid • Mounting kit for separation punch • 8 x sheet hold-downs for standard pile delivery • 4 x cross support bars Options: • QTM – Patented guide rails • QTM – Chase with quick lock system and X/Y adjustment • QTM – Upper stripping frame with quick lock system • QTM – Upper delivery frame with quick lock system • Control upgrade to latest Siemens S7 controller • New generation frequency converters • Modem for remote service connection • Machine height increase: 900 mm

Condition: excellent (used), Year of construction: 2002, 1) Bobst Dynaload prefeeder year 1998 2) Bobst Flexo 160 year 2002 n. 5 colors, Vacuum transport, rubber roller Bobst CUBE 3) Bobst SPO 160 A Matic year 2002 Hjdpfx Ajv Nywvjf Ujfg Introduction of suction cup Center Line II Stripping station with motorized Quick Lock tool clamping Batch delivery with gripper trim extraction Bobst CUBE

Condition: excellent (used), Year of construction: 2018, operating hours: 10 h, functionality: fully functional, Automatic toilet paper and kitchen towel packing machine We have used it for less than 10 hours. After purchase, it did only a couple of test runs and then was stored in a dry warehouse for later use. It had never been used since. There might be some bends on the machine since it has been moved a couple of times. Specification Power 220V 50Hz Packing: Toilet paper 2/4/6/8/10 rolls per pack with handle, Hand towel 2/4 rolls per pack with handle Hodpfx Afeuyhf He Usfg Packing in film, overwrapping with meld line on the back. It uses opp film, a max roll diameter of 30cm, and a thickness of 0.03 - 0.10 by the specification, no idea about other materials - have not tested any. For setting up and configuration the machine you will have to contact the manufacturer The machine can be seen, powered on, and set to automatic/manual running. User manual is available, have videos from the manufacturer only

Condition: used, Year of construction: 2002, Die-cutter Iberica JRK-105 Year: 2002 Description: Stripping unit Blanking unit Technical specifications: Hfjdpfx Aev Rci Djf Ujg Maximum sheet size: 750 x 1050 mm Minimum sheet size: 350 x 400 mm Minimum paper thickness (according to quality):90 – 95 g/m2 Maximum cardboard thickness: 1.5 mm Maximum corrugated board thickness: 3 mm Maximum operational pressure: 300 T Maximum speed: 8500 sheets/hour Main drive motor with variable speed: 20 CV (15 KW) Total power installed: 43 CV (32 KW) Air required pressure: 6 KG / CM2 Machine appr. Weight: 23.600 KG Floor space occupied: length 10.10 M. width 6.26 M. height 3.30 M.

Condition: used, type of input current: three-phase, product width (max.): 1,600 mm, The machine is designed for slitting and rewinding of flexible materials such as plastic films, paper, laminates, adhesive tapes and foils. Hsdpjyy Rh Eofx Af Uefg Technical details: - Working width: 1600 mm - Slitting system: razor blades / rotary knives - Materials: PE, PP, PET, PVC, paper, laminates - Input voltage: 400V / 3-phase

Condition: used, Year of construction: 2018, operating hours: 69,000,000 h, functionality: fully functional, Folder gluer machine Folding carton with longitudinal seam: max. 1,150 × 600 mm min. 75 × 55 mm min. 45 × 55 mm (with small carton device) Crash-lock bottom carton: max. 1,150 × 600 mm min. 146 × 80 mm 4-corner box (erected): max. 1,150 × 680 mm min. 120 × 110 mm 6-corner box (erected): max. 1,150 × 630 mm Hjdpfxoyg Edgj Af Uefg min. 250 × 130 mm With BELKHOFF control system Roller and drying tunnel TÜNKERS EAS 480 delivery station, right-hand, year of manufacture 2019

Year of construction: 1979, condition: ready for operation (used), functionality: fully functional, Non-binding offer Automatic Die Cutting Machine Manufacturer: BOBST Autoplatine Hfjdpsyrxyrjfx Af Uog Model: SP-102 E Sheet Size: 1020 x 720 mm Year of Manufacture: 1979 Technical Data: - Max. Sheet Size: 1020 x 720 mm - Min. Sheet Size: 40 x 35 mm - Material Range: Paper/Cardboard: 80 – 1,000 g/m² Cardboard: 250 – 2,000 g/m² E+B flute: max. 4 mm - Max. Cutting Pressure: 250 t - Max. Production Speed: 7,500 sheets/h - Fully automatic die cutting machine with stripping station - Automatic high-pile feeder - High-pile delivery - Die cutting plates - Chase frames - Quick-action chase changing system - Complete with accessories - Machine in operating condition and well maintained - Video presentation available upon request! Price: on request Delivery: FCA Availability: immediately

Condition: used, Year of construction: 2012, Pre-feeder Para for midi line Hedpeywuw Ssfx Af Uefg

Year of construction: 2002, condition: ready for operation (used), An Edelmann converted from a gravure printing machine into a rotary die-cutting machine is available. Principle: inline web processing with sheet stacking, materials: paper/cardboard/labels/die-cut parts, tool mounting: die-cutting plates, tool holder: magnetic cylinder, magnetic cylinder circumference: 24in, tool cassette: 12in, web width: 485mm, max. material width: 485mm, material weight range: 35-170g/m², max. roll diameter: 1200mm, max. production speed: 200m/min, production steps: roll-rotary die-cutting/cross-cutting/high-pile delivery. The machine ran little and is in as-new condition. Documentation available. An on-site inspection is possible. Hfsdpsyt N Dkjfx Af Uog

Year of construction: 1996, condition: used, Technical details: • Working width: 400 mm Hfjdpfxeyub Sij Af Ueg • Max. speed: up to 150 m/min • 20 magnetic cylinders included • Die-cutting station with magnetic cylinders • Slitting unit • Matrix waste removal • Rewinding unit for finished rolls • Suitable for self-adhesive label materials (paper and film)

Condition: ready for operation (used), Numeriek gestuurd Japanse elektronica werkt betrouwbaar, 720 mm snijbreedte, zeer stabiel en zwaar gebouwd (1400 kg), kogelomloop spindel voor spelingsvrij instellen van het zadel. Manual en extra mes ingegrepen. Prijs “as is” geladen op uw transport, excl. eventuele gecertificeerde verpakkingskosten. Hjdpsw R En Hefx Af Uofg

Year of construction: 1966, operating hours: 10,000 h, condition: excellent (used), functionality: fully functional, outer diameter: 420 mm, machine/vehicle number: 58256, Nebiolo Saturnia in very good condition. From first owner, at first used as a letterpress in the upcoming market with offset in the 70's. The company always produced with it's offset to maxima 50/70 size. Situated as a local printer in a village, the Nebiolo was sometimes used for rilling, slitting, scoring some offset jobs. very good machine, low noise, excellent condition of al mechanical parts. Airpump for feeder and delivery is for a later make = Becker dry-pump 100m3 with low noise. All parts necessary for the machine come with the machine, even as the original operational book and spare-parts book. The cylinder has a 6 cm larger diameter than a KBA Condor and it weights 800kgs, only 200 kgs less of that of a heidelberg SBB/SBD. The delivery is different and for carton better that that of its competitors: a triple drum delivery, turning the front side up again on the belts which transport it to the pile. Best is to replace the individual belts for one large belt and make some extra attention for laying the sheets down when coming from the belt with better air facilities. Of course we can arrange that for you either. Then you have a faster, very easy to operate and maintain with better productivity and at least the same durability (with lower noise-level due to less moving parts) than an heidelberg SBD with approx the same size for more than double the money. Really a nice product from Nebiolo even as it big brother Urania. They have pull-lays but can easily turn over to push side lays. Some specs: Max paper size 650 x 950 mm Min paper size 300 x 420 mm Speed 1500 - 4000 imp/hour Feeder pile height 550 mm Delivery pile height 650 mm Impression force approx. 35000 N (not adjustable in lighter or heavier, only one value) Bearer height 24,85 mm; machines needs "normal - Bobst standard" 23,80 diecut forms/lines with a hardened steel plate under the form so that small compensations could be made with thin band and paper under this hardened plate. This is the only and best method. A 45 to 47 HRC plate will be delivered with the machine, even as a new cylinder jacket. Feeder and delivery use an additional extern pump, Becker, 100m3, 2kW Hjdpfx Astyyvwjf Uefg Size of the machine (approx, with steps) L x W x H = 330 x 220 x 190 cm Weight net 4,800 kgs