Used Bimak 35 Me for sale (28,903)

Condition: new, Year of construction: 2024, flue capacity: 510 kW Conventional yeld capacity: 407 kW flue diameter: 250 mm hot air delivery pipes: 4 x 350 mm Febu Ucsk Utrwj U Eegb flue length: 1900 mm oven width: 900 mm oven hight: 900 mm air flow: 26000 m³/h power consumption: 4500 W aproximate surface to heat up: 8000 m³ area to be heated: 1800 m² heater height without hot air conveying pipes: 3000 mm heater width: 1220 mm heater length: 2700 mm weight: 1575 kg

Condition: used, Year of construction: 2022, operating hours: 504 h, load capacity: 6,000 kg, lifting height: 34,900 mm, mast type: telescope, power: 175 kW (237.93 HP), fork carriage width: 1,400 mm, ground clearance: 310 mm, front tire type: Magni, front tire size: 445/65R22,5, rear tire type: Magni, rear tire size: 445/65R22,5, total length: 9,290 mm, wheelbase: 3,300 mm, engine type: Volvo Penta TAD, drive type: Diesel, construction width: 2,540 mm, net weight: 24,000 kg, - Drehbarer Teleskopstapler RTH 6.35 - Maximale Tragkraft 6.000 kg (Schwerpunkt 600 mm) - Maximale Hubhöhe 34,90 m - Drehung 360 Grad (durchgehend) - Motor: Typ Volvo TAD 583 VE, Stage V - Nennleistung 175 kW (238 PS) bei 2.300 U/min - Max. Drehmoment 975 Nm bei 1.380 U/min - Hubraum 5,13 l - Zylinderzahl 4 in Reihe - Motorkonfiguration Dieselmotor mit Direkteinspritzung und Turboaufladung - Kühlanlage Wassergekühlter Ladeluftkühler - Antrieb Typ Hydrostatisch - Modell Danfoss / Rexroth - Max. Druck 480 bar - Fördervolumina: Elektronisch geregelte Axialkolbenpumpe. Verstellmotor. Fgsbujvkh Rmo Uc U Eeb - Getriebe Dropbox-Getriebe mit 2 Fahrstufen für Vorwärts- und Rückwärtsfahrt - Achsen und Bremsen: Typ Achsen mit Planeten-Endantrieben - Hinterachse Lenkende Pendelachse mit hydraulischer Sperre - Vorderachse Pendellenkachse mit Niveauausgleich +/- 8 Grad - Betriebsbremse Ölbad-Lamellenbremse an jeder Achse, hydraulisch betätig - Feststellbremse Negativbremse, hydraulisch betätigt - Reifengröße 445/65 R22,5 - Max. Fahrgeschwindigkeit 40 km/h - Max. Zugkraft am Lasthaken 152 kN - Steigfähigkeit 65% - Wenderadius (mit Gabelzinken) 7.000 mm - Dieselkraftstoff 270 l - AdBlue 40 l - Hydrauliköl 220 l -Motoröl 16 l - Kühlflüssigkeit 40 l - Max. Betriebsdruck 350 bar -Anlagentyp Load sensing - Betriebspumpe Danfoss / Rexroth Verstellpumpe - Verteiler für Ausleger- und Oberwagenbewegungen: Danfoss Elektroproportionalventil SIL 2 - Verteiler für Stützen Bosch Rexroth Elektrohydraulische Aktuatoren - Bewegungssteuerung Zwei 2-Achsen-Joysticks Danfoss mit Totmanneinrichtunf - Steuerung mit CAN-Bus-Technologie

Condition: refurbished (used), Year of construction: 2005, Functionality: fully functional, travel distance X-axis: 350 mm, travel distance Y-axis: 250 mm, travel distance Z-axis: 300 mm, workpiece weight (max.): 500 kg, Charmilles Roboform 350 Year of manufacture 2005 C-frame design Fixed table with lowerable basin Travel paths: X=350 mm, Y=250 mm, Z=350 mm Max. workpiece size: X=780 mm, Y=530 mm, Z=300 mm Fsbuowhfqqo Uc U Ejgb Max. workpiece weight: 500 kg Max. electrode weight: 50 kg Distance table to chuck: 150 - 450 mm Operating current: 64 amps Best achievable surface finish: Ra 0.1 µm Integrated Accura C-axis Linear glass scales with 0.05 µm measurement resolution Including Erowa ITS 50 pneumatic chuck Machine weight (net): 2800 kg Machine dimensions (L x W x H): 1900 x 1690 x 2522 mm The machine has already been cleaned, serviced, and thoroughly tested. We would be happy to commission the machine for you.

Condition: excellent (used), Year of construction: 2001, Arburg 470S 1300-350 Year of manufacture: 2001 injection unit: Screw diameter: 35 mm injection weight: 117 g Injection pressure: 2500 bar Metering volume: 139 ccm Clamping unit: clamping force: 130 t tie bar distance: 470x470 mm size of clamping platens: 650x650 mm ejector: hydraulic clamping unit: hydraulic Fjbowig Efou Uc U Eegb Control system: SELOGICA Additional equipment: Euromap 12 Robot interface Hydraulic core pull x 1 Control with hot runners x 6 Injection unit hardened - bimetal Proportional valve on the injection unit - precise injection The built-in system for control of the pressure quality from the brand Sensor Kistler - measurement of the mold pressure type of injection unit: Vario - it offers the possibility to use the injection unit e.g. for lateral injection The new injection unit is installed in the machine Dimensions: Weight: 5100 kg Length/width/height: 4.45x1.49x2.17 m Drive: Pumps/motor: 22 kW Heating power: 10,2 kW Total power: 32,2 kW All offered machines are started by our service technicians before sale. It is possible to get a video of technical tests of the selected machine or participate in live technical tests in our company in Łódź. Price: Upon request

Condition: excellent (used), Year of construction: 2010, Functionality: fully functional, travel distance X-axis: 1,035 mm, travel distance Y-axis: 560 mm, travel distance Z-axis: 510 mm, rapid traverse X-axis: 25 m/min, rapid traverse Y-axis: 25 m/min, rapid traverse Z-axis: 25 m/min, feed rate X-axis: 20 m/min, feed rate Y-axis: 20 m/min, feed rate Z-axis: 20 m/min, nominal power (apparent): 17 kVA, torque: 83 Nm, controller manufacturer: Heidenhain, controller model: Heidenhain TNC 620, total height: 2,665 mm, total length: 3,250 mm, total width: 2,779 mm, table width: 560 mm, table length: 1,200 mm, table load: 720 kg, overall weight: 4,100 kg, spindle speed (min.): 20 rpm, spindle speed (max.): 9,000 rpm, number of spindles: 1, number of slots in tool magazine: 20, tool length: 300 mm, tool diameter: 80 mm, tool weight: 6,000 g, Equipment: documentation/manual, rotational speed infinitely variable, Used DMC 1035 V eco for sale – High-performance vertical machining center Upgrade your manufacturing processes with this robust and powerful DMC 1035 V eco from DMG MORI! This vertical machining center is ideal for a wide range of milling tasks and offers outstanding performance when machining a wide variety of materials. Key Features: High rigidity and stability: Ensures precise machining results and a long service life. Large work area: Provides sufficient space for machining large workpieces. High spindle speed: Enables fast and efficient machining processes. Robust construction: Guarantees a long service life and reliable performance. CNC control: Equipped with a user-friendly CNC control for easy programming and operation. Additional Information: Fgebu Uswhkg Roc U Ejb Year of Manufacture: 2010 Condition: Good, Used Control: Heidenhain TNC 620 Travel Range: 1,035 x 560 x 510 mm Speeds: 20 - 9,000 rpm Ideal for: General Machining Tool and Mold Making Single-Part and Small-Batch Production Mechanical Engineering Why this DMC 1035 V eco? This machine has been regularly serviced and is in good used condition. It offers a cost-effective way to expand your manufacturing capacity and increase your productivity.

Condition: used, Year of construction: 2006, Biesse Rover B 4.35 CNC Machine Description: Working fields: X = 3200 mm; Y = 1315 mm; Z = 150 mm Table type: Beam table (manually) 6 bars with 3 cups 1 milling motor Motor 9 kW Drilling unit: BH-17 Tool holder: ISO-30 Changer: 9 positions moving along Number of vacuum pumps: 1 Biesse Works (All changes, mistakes in technical data, info and prices reserved. Availability subject to prior sales. No guarantee on printed data!) (Alle Änderungen und Irrtümer in den technischen Daten, Angaben und Preisen sowie Zwischenverkauf vorbehalten! Keine Garantie auf gedruckte Daten!) Fgjbujwgctge Uc U Ejb Best woodworkingmachines from the Netherlands Holland Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland

Condition: used, Functionality: fully functional, Year of construction: 2010, operating hours: 14,089 h, load capacity: 3,500 kg, lifting height: 3,500 mm, fuel type: diesel, mast type: standard, drive type: Diesel, Diesel forklift Mast type: Standard Condition: Ready for use and fully functional Technical condition: good Fobu Uc Uev Dy Nbo Esgb Description: For dealers or export only 3rd valve, 4th valve,

Condition: used, Year of construction: 2021, operating hours: 569 h, load capacity: 3,500 kg, lifting height: 12,550 mm, mast type: telescope, power: 75 kW (101.97 HP), fork carriage width: 1,140 mm, ground clearance: 410 mm, front tire type: Alliance, front tire size: 400/80-24, rear tire type: Alliance, rear tire size: 400/80-24, total length: 7,071 mm, wheelbase: 2,880 mm, drive type: Diesel, construction width: 2,280 mm, net weight: 9,080 kg, - Max. Tragkraft: 3500 kg - Max. Hubhöhe: 12,55 m Febu Uc Uewhgd Ej Eegb - Maximale seitl. Reichweite: 8,75 m - Ausbrechkraft mit Schaufel: 5803 daN - Kippwinkel 12 Grad - Schüttwinkel 114 Grad - Wenderadius: 3,65 m - Bereifung: Pneumatisch - Reifenmodelle Alliance 400/80 - 24 - 162AB - Heben 10,2s - Senken 8,9 s - Teleskop ausfahren 14,60 s - Teleskop einfahren 10,40 s - Ankippen 5s - Auskippen 4s - Motonorm Stage IV - Anzahl Zylinder / Tragfähigkeit der Zyliner 4-3400 cm³ - Zugkraft 7400 daN - Getriebetyp: Drehmomentwandler - Parkbremse Automatische Feststellbremse - Feststellbremse Ölbad Lamellenbremsen an den Vorder- und Hinterachsen - Pumpenart: Zahnradpumpe - Hydraulikfördermenge/Hydraulikdruck: 125 l/min / 270 bar - Motoröl: 7,5l - Hydrauliköl: 140 l - Fassungsvermögen des Kraftstofftanks: 120 l - Inhalt DEF Tank: 12l - Geräuschpegel im Fahrerstand LpA 78 dB - Umgebungsgeräusch 103 dB - Steuerungen JSM

Condition: used, engine output 5 kW saw-blade dia. 300-350 mm Working speed 0-40 m/min weight ca. 1550 kg kg Concept 350 PLUS "Partnership Edition" pressure beam saw Cutting length: 3.200 mm ----- combines the advantages of different sawing systems. Flexible as one Panel saw, precise and safe like a pressure beam saw and ergonomic like a rip saw ----- Manufacturer description: - Saw unit can be swiveled up to 46° - Pressure bar, including LED lighting with 3 different action colors: WHITE: Machines in rest position RED: Pressure bar lowers or emergency stop function BLUE: Sawing unit moves - variably usable support table 1,000 x 500 mm - Scoring system using the main saw blade in synchronization - Automatic workpiece length detection for minimal travel distances - Mobile and height-adjustable control panel, including: Saw blade stand, template holder, emergency stop button, start button, selector switch Groove/score saws/saws, rotary switch feed speed, switch for Laser (option) and USB socket Partnership Edition including: - Motorized width stop with 4 aluminum stops, which move synchronously. All 4 stops move up to 1,300 mm. The table is approx. 2,000 mm long. - Screen control (8'' touchscreen). The graphical interface offers the following functions: Tool database, angle cut calculation at the length stop, Cutting plans can be created and saved, programs can be saved USB can be saved, exported and imported. - Telescopic stop extendable to 3,400 mm including 2 digital displays Technical data: - Max. saw blade projection 350mm saw blade: 100 mm at 90° / 70 mm at 45° - Saw blade: diameter 300 - 350 mm, bore 30 mm - Rotation of saw blade: 4,000 rpm. - Motor: 5 kW (= 7.5 HP) - Feed speed: 0 – 40 m/min. - Total length: approx. 3,670 / 4,270 / 4,870 mm (depending on cutting length) Fjbu Ustg Aihoc U Esgb - Weight: from approx. 1,150 to 1,550 kg (depending on cutting length and equipment) - Required air pressure: 7 bar - Suction nozzle: 1 x 100 mm, 1 x 120 mm Model variants: - CONCEPT 350 PLUS with 2,600 mm cutting length - CONCEPT 350 PLUS with 3,200 mm cutting length - CONCEPT 350 PLUS with 3,800 mm cutting length - CONCEPT 350 PLUS with 4,000 mm cutting length and bigger on request! ----- Price of the above-mentioned machine with equipment variant on request! ----- General options with extra charge: - 3410451 cutting line laser - saw motor with 7.5 kW (10 HP) including automatic star-delta Start-up - 41/03 programmable saw blade height adjustment - 3380132 Miter stop +/- 50° swiveling with length compensation, incl. Telescopic stop with folding stop - 3380135 Miter stop +/- 50° swiveling with length compensation, incl. 2 Digital displays: 1 digital display for folding stop, 1 digital display for the stop on the telescopic extension -3380136 Miter stop swivels +/- 50° with length compensation, including 3 Digital displays: 1 digital display for folding stop, 1 digital display for the stop on the telescopic extension, 1 digital display for the miter indicator - 3380138 additional support table 800 x 200 mm, can be attached - 3515013 Auxiliary stop for long, narrow workpieces, adjustable via scale (Support table 3380138 required) - 3515014 Auxiliary stop for long, narrow workpieces, adjust...

Condition: excellent (used), Year of construction: 2002, Arburg 420C 1000-350 / Very good technical condition Year of construction: 2002 Injection unit: Screw diameter: 40 mm Injection weight: 153 g Injection pressure: 2120 bar Dosing volume: 182 ccm Clamping unit: Clamping force: 100 t Distance between tie bars: 420x420 mm Size of the clamping platens: 570x570 mm Ejector: hydraulic Clamping unit: hydraulic Control system: SELOGICA Additional equipment: Euromap 12 Euromap 67 Robot interface Hydraulic core pull x 1 Control unit with hot runners x 10 Hardened injection unit - bimetal The machine is integrated with the original conveyor belt from the Arburg brand Built-in sorting flap Dimensions Weight: 3430 kg Length/width/height: 4.35x1.64x2.08 m Fgebu Uc Uewig Dbo Ejb Drive: Pump/motor: 22 kW Heating output: 10.2 kW Total output: 32.2 kW All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: used, Year of construction: 2007, 2007 | Holland-Lift | Holland-Lift Q 135 El 24 (15m) | Used Scissor Lift 📍Location: Estonia, Tallinn 🚛 We Deliver to your destination – Estimate the shipping cost with our calculator! 💰 Buy Now for EUR 8900 or Make an Offer. Request payment at delivery for an affordable fee! (subject to approval)* Fobu Ucswhgyae U Eegb 👷‍♂️ Inspected by an independent expert 32 inspection points 26 approved ✅ 6 imperfect ℹ️ 0 issues ⚠️ 📌 Inspector's Comment: The hourmeter is broken, and the protection plate near the drive motor is bent. The drive motor is in good condition, and all operations work, except the lifting leveling sensor, which occasionally malfunctions. The customer defrosted the remote and charged the batteries before the inspection. ❓Want the Full Inspection Report, Extra Photos & a Video? 🔍 Search this on Google for full details!: "38110 Equippo" 💡 Why Buy from Us? ✔ Fully inspected machines ✔ Delivered to your jobsite ✔ Money-Back Guaranteed ✔ Safe payment methods with possibility to pay at delivery ❓Got machines to sell? Contact us for a free evaluation

Condition: good (used), mileage: 80,000 km, power: 132 kW (179.47 HP), first registration: 05/2022, fuel type: diesel, color: white, axle configuration: 4x2, tire size: 195/75R16C, fuel: diesel, wheelbase: 4,100 mm, driver cabin: day cab, gearing type: automatic, emission class: euro6, suspension: steel, loading space width: 2,100 mm, loading space length: 4,100 mm, loading space height: 400 mm, Year of construction: 2022, Equipment: air conditioning, differential lock, parking heater, trailer coupling, = Additional Options and Accessories = - Electric Windows - Air Conditioning Fgebewgpbwju Uc U Eob - Fog Lights - Power Steering - Stability Control - Auxiliary Heating - Toolbox - Xenon Headlights - Central Locking = Additional Information = Tire Size: 195/75R16C Brakes: Disc Brakes Suspension: Leaf Spring Front Axle: Max. Axle Load: 2100 kg; Steered; Left Tire Tread: 60%; Right Tire Tread: 60% Rear Axle: Dual Tires; Differential Lock; Max. Axle Load: 2600 kg; Left Tire Tread Inside: 60%; Left Tire Tread Outside: 60%; Right Tire Tread Inside: 60%; Right Tire Tread Outside: 60% Engine Capacity: 2,998 cc Technical Condition: Good Visual Condition: Good

Condition: used, Functionality: fully functional, Year of construction: 2019, operating hours: 11,442 h, load capacity: 3,500 kg, lifting height: 3,550 mm, fuel type: diesel, mast type: standard, drive type: Diesel, Diesel forklift Fsbu Uc Uev Aq Rmo Ejgb Mast type: Standard Condition: Ready for use and fully functional Technical condition: good Sideshift, double pallet fork, 3rd valve, 4th valve, heating, full cab,

Condition: used, Year of construction: 2019, Sanding width: 1.350 mm Workpiece thickness min: 4 mm Passage height max: 170 mm Sanding aggregates total: 2 Sanding rollers: 2 Steel roller: Yes Fgsbu Uewhfc Hoc U Eob Combination unit: 1 Sanding pads total: 1 Vacuum table: Yes Sensing of workpiece thickness: mechanical Main motor power: 11 kW Feedrate max: 9 m/min Blow-off device: Sanding belt Configuration of aggregates: r-c-u Side of belt change: Left Protection against workpiece over-thickness: Yes Control: B&R Power Panel Conformity marking: CE mark Weight: 2.060 kg Space requirement Length: 2 m Space requirement Width: 1,9 m Space requirement Height: 2,4 m

Condition: new, Manual hand unit Nein J/N Automatic for single pieces Ja J/N Automatic for frames Nein J/N Clip set "351" on the loose item ----- Manufacturer description: - Base frame in stable welded construction - Clip container as tipping conveyor with separation and feeding the clips - Screwdriver with tipping conveyor for the screws to be separated, feed screwdriver pneumatic with depth adjustment - Conveyor belt length approx. 4,000 mm as NC axis - Contact and clamping cylinder - Electro-pneumatic control via PLC It can programs with different Initial and distance dimensions can be entered - Workflow automatically in flow ----- Technical specifications: - Screw height 50-120 mm - Profile length 350-3,500 mm - Table height approx. 950 mm ----- Total price of the machine ex works: on request! Freight costs within Germany: on request ! Installation, commissioning and instruction within Germany: on request ! ----- Video shows version with extra infeed belt and outfeed belt with pusher. Not included in the basic price. Can be offered as an option if required. (technical data according to the manufacturer without guarantee!) Febu Ucskx Stno U Eegb

Condition: excellent (used), Year of construction: 2017, Wittmann Battenfeld EcoPower 110/350 with the Wittmann W818 robot / Electric machine / Operating hours: approx. 16,000 in automatic mode Year of manufacture: 2017 Injection unit: Screw diameter: 35 mm Injection weight: 153.8 g Injection pressure: 2083 bar Dosing volume: 169 cc Clamping unit: Clamping force: 110 t Bar spacing: 470x420 mm Size of the clamping plates: 680x660 mm Ejector: electric Clamping unit: toggle lever Control: UNILOG B8 - touchscreen Additional equipment: Perfect technical condition Electric machine: high-speed, energy-saving and very quiet Operating hours: approx. 16,000 in automatic mode Euromap 67 Robot interface Control with Air valve Hydraulic core pull x 1 Control with hot runners Injection unit is wear-resistant and resistant to corrosion Febewigwbsu Uc U Esgb Central lubrication Automatic tool height adjustment Parallel movements The machine was serviced in Germany Robot Wittmann W818 Year of manufacture: 2015 4-axis robot: 3 axes are driven by servo motors (electric); axis C - pneumatic Travel paths in axes: X-420, Y-1200, Z-2000 Touch control panel The safety package for robots Robot with adapter, conveyor belt and protective housing Purchase of the robot and the conveyor belt for an additional charge Dimensions: Weight: 4800 kg Length/width/height: 4.91x1.42x2.10 m All machines offered are started by our service technicians before sale. It is possible to receive a video of the technical tests of the selected machine or to take part in live technical tests in our company in Łódź. Price: On request

Condition: new, Number of motors 2 Stück 0 3000 mm Control ja/CNC loading dimensions L x W x H 4000 x 1500 x 1500 mm Weight 800 kg HECHT double miter saw Exenso DS350E - 3000 mm ----- For wooden glass strips, rungs, profile strips, aluminum strips, etc. Pos. 1.1 Article number 942.5103 1 piece HECHT Exenso DS350E - Working length 3000 mm - Swivel range 22.5° (inside) to 135° (outside) - Right head movable - Saw blade holder Ø 350 mm - Incl. 1 piece center support. - Units clamped pneumatically. - Positioning control Exenso DS3 with touch panel 15" display in dust-proof monitor housing. - 3-axis control, 1 longitudinal axis and 2 swivel axes. - Entering the cutting data by hand - Processing data from a cutting list (data set according to specification) - Processing measuring rod data (GMF wireless caliper) - Ethernet connection 10/100 (TCP/IP) - USB interface - Incl. control cabinet, motor and software licenses. Fjbu Ujvzt D Tec U Eogb Item 1.2 Item number 723.0121 2nd DS saw blade wood Bevel/bevel/flat tooth - positive Item 1.3 Item number 942.5236 2 sets of DS workpiece clamping combined Combined workpiece clamping consisting of: Pneumatic swivel clamp - for clamping the material from above. (Free access to the work table) Pneumatic horizontal clamp - anti-twist clamping cylinder with pressure piece. The clamps can be selected individually via the saw control. The clamping sequence can also be set via the control. Including safety pre-tensioning pressure Scope of delivery for 2 sets: - 2 pieces (left/right) vertical swivel clamps. - 2 pieces (left/right) horizontal clamps. Item 1.4 Article number 942.5997 DS pneumatic feed device Item 1.5 Article number 945.2007 Packaging DS350 (transport frame) ----- Total price in this version - on request! ----- ALTERNATIVE options, prices on request! ----- For horizontal clamping of the remaining pieces with blunt glass strips instead of the 2nd set Item 1.3 943.5236 DS workpiece clamping combined! Pos. 2.1 Article number 942.5201 ES / DS workpiece clamping from the front - 2 clamping cylinders with anti-twist protection - 2 cylinder holders with clamping lever ----- For rebated glass strips, instead of standard panels without a groove: Pos. 2.2 Article number 942.5241 DS350 table supports grooved according to customer sample The assembled table supports are milled according to the customer's drawing. Please send us all profile drawings that are to be sawn (pdf, dxf and hand samples) ----- If, for example, aluminum is also to be sawn: Item 2.3 Article number 942.5203 DS hydropneumatic feed device (instead of pneumatic feed cylinder) ----- OPTIONAL accessories, with additional charge on request: ----- Item 2.4 Article number 942.5237 DS "Excess length" software (subsequent steps must be confirmed) Sequence control including hardware. After entering a cutting dimension > max. cutting length of the system, the cutting is carried out in a cyclical manner. (Left unit cuts, right unit moves the material and cuts to size.) ----- Item 2.5 Article number 944.1023 GMF caliper 3000mm complete set (1500mm plus extension 1500mm) incl. charger and receiver. A robust aluminum measuring rail with a measuring ran...

Condition: excellent (used), Year of construction: 2012, Wittmann Battenfeld EcoPower 110/350 / Electric machine / Production line with the Wittmann W818 robot Year of manufacture: 2012 Injection unit: Screw diameter: 35 mm Injection weight: 153.8 g Injection pressure: 2083 bar Dosing volume: 169 cc Clamping unit: Clamping force: 110 t Bar spacing: 470x420 mm Clamping plate size: 680x660 mm Ejector: hydraulic Clamping unit: electric Control: UNILOG B6 - touchscreen Additional equipment: Electric machine: high-speed, energy-saving and very quiet Euromap 67 Robot interface Air valve x 1 Hydraulic core pull x 1 Control with hot runners x 12 Injection unit is wear-resistant and resistant to Corrosion Central lubrication Automatic tool height adjustment The machine was serviced in Germany Robot Wittmann W818 Year of manufacture: 2012 4-axis robot: 3 axes are driven by servo motors (electric); movement A and C Travel paths in axes: X-420, Y-800, Z-1500 Fgsbu Uc Uswigvdo Ejb Touch control panel Robot with adapter, conveyor belt and protective housing Purchase of the robot and conveyor belt for an additional charge Dimensions: Weight: 4300 kg Length/width/height: 4.91x1.42x2.10 m All machines offered are started by our service technicians before sale. It is possible to receive a video of the technical tests of the selected machine or to take part in live technical tests in our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2011, Sumitomo Demag Systec 350/720-1450 with the Wittmann-Demag W833 robot / Very good technical condition Year of manufacture: 2011 Injection unit: Screw diameter: 70 mm Injection weight: 946 g Injection pressure: 1400 bar Dosing volume: 1039 cc Clamping unit: Clamping force: 350 t Type distance: 720 x 720 mm Clamping platen size: 1040 x 1060 mm Ejector: hydraulic Clamping unit: toggle lever Control system: NC5 Additional equipment: Machine in very good technical condition Air valves x 4 Hydraulic core pullers x 2 Control system with hot runners Injection unit hardened - bimetal Central lubrication system Built-in printer Fsbswigr Eju Uc U Esgb Wittmann-Demag robot W833 Year of manufacture: 2011 4-axis robot: 3 axes are driven by servo motors (electric); C-axis - pneumatic Travel paths in axes: X-900, Y-1600, Z-3000 Touch control panel Robot safety package Robot with adapter and protective housing Robot purchase for an additional charge Dimensions: Weight: 15760 kg Length/Width/Height: 6.90 x 2.00 x 2.30 m All offered machines are started by our service technicians before sale. It is possible to receive a video of the technical tests of the selected machine or participate in live technical tests at our facility in Łódź. Price: Upon request

Condition: excellent (used), Year of construction: 2000, Arburg 370S 800-350 Year of manufacture: 2000 Injection unit: Screw diameter: 35 mm Injection weight: 117 g injection pressure: 2500 bar Metering volume: 139 ccm Clamping unit : Fgjbewigm Nju Uc U Esb clamping force: 80 t tie bar distance : 370x370 mm size of clamping platens: 570x570 mm Ejector: hydraulic clamping unit: hydraulic Control system: SELOGICA Additional equipment: Euromap Robot interface Hydraulic core pull x 2 Injection unit hardened - bimetal Built-in sorting flap Integrated lateral original Arburg sprue picker Dimensions: Weight: 3800 kg Length/width/height: 4.06x1.39x2.12 m Drive: Pumps/motor: 18.5 kW Heating power: 10,2 kW Total power: 28,7 kW All offered machines are started by our service technicians before sale. It is possible to get a video of technical tests of the selected machine or participate in live technical tests in our company in Łódź. Price: Upon request

Condition: excellent (used), Year of construction: 2008, Arburg OK-C S350-60 / Vertical injection molding machine with sliding table / Very good technical condition Year of manufacture: 2008 injection unit: screw diameter: 18 mm injection weight: 18 g injection pressure: 2500 bar Dosing volume: 20 ccm Clamping unit: Clamping force: 35 t tie bar distance: 0x0 mm size of clamping platens: 295x395 mm ejector: hydraulic clamping unit: hydraulic Control system: SELOGICA - touch screen Additional equipment: Vertical injection molding machine with sliding table 3 stations on the sliding table Air valve x 4 Hydraulic core pull x 1 Control system with hot runners Injection unit hardened - bimetal Parallel movements Infrared protection curtains It is possible to change the screw diameter Fgsbuowiggis Uc U Eeb Dimensions: Weight: 2500 kg Length/width/height: 2.55x1.85x3.52 m All offered machines are started by our service technicians before sale. It is possible to get a video of technical tests of the selected machine or participate in live technical tests in our company in Łódź. Price: Upon request

Condition: excellent (used), Year of construction: 2003, Arburg 320S 350-60 Year of construction: 07.2003 Injection unit: Screw diameter: 18 mm Febu Uc Ujwiggce Eegb Injection weight: 18 g Injection pressure: 2500 bar Dosing volume: 20 ccm Clamping unit: Clamping force: 35 t Distance between tie bars: 320x320 mm Size of the clamping platens: 446x446 mm Ejector: hydraulic Clamping unit: hydraulic Control system: SELOGICA Additional equipment: Euromap 12 Robot interface Air valve x 2 Hydraulic core pull x 2 Control unit with hot runners Hardened injection unit - bimetal Built-in pressure quality control system from Sensor Kistler - mold pressure measurement Built-in sorting flap and conveyor belt Dimensions: Weight: 2150 kg Length/width/height: 3.32x1.21x1.81 m Drive: Pump/motor: 7.5 kW Heating output: 2.7 kW Total output: 10.2 kW All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2004, Arburg 320S 350-150 with the Wittmann W621 robot Year of construction: 2004 Injection unit: Screw diameter: 25 mm Injection weight: 49 g Injection pressure: 2500 bar Metering volume: 54 ccm Clamping unit: Clamping force: 35 t Distance between tie bars: 320x320 mm Size of the clamping platens: 446x446 mm Ejector: hydraulic Clamping unit: hydraulic Control system: SELOGICA Additional equipment: Euromap 67 Robot interface Air valve x 2 Hydraulic core pull x 2 Control unit with hot runners Hardened injection unit - bimetal Proportional valve on the injection unit - precise injection Built-in pressure quality control system from Sensor Kistler - mold pressure measurement Original mold crane Robot Wittmann W621 Year of manufacture: 2005 5-axis robot: 3 axes are driven by servomotors (electric); axis B (rotation) and axis C Travel in axes: X-550, Y-1000, Z-1500 Touch control panel Robot with adapter Purchase of the robot for an additional charge Dimensions Weight: 2250 kg Fjbu Uc Uowigflo Ejgb Length/width/height: 3.44x1.24x2.04 m Drive: Pump/motor: 18.5 kW Heating output: 9.4 kW Total output: 27.9 kW All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2015, Wittmann Battenfeld SmartPower 90/350 / hybrid machine / operating hours: approx. 24,000 in automatic mode Year of manufacture: 2015 Injection unit: Screw diameter: 35 mm Injection weight: 153.8 g Injection pressure: 2083 bar Dosing volume: 169 cc Clamping unit: Clamping force: 90 t Bar spacing: 470x420 mm Clamping plate size: 680x660 mm Ejector: hydraulic Clamping unit: hydraulic Control: UNILOG B6 - touchscreen Additional equipment: Hybrid machine: high-speed, energy-saving and very quiet Machine in perfect technical condition Operating hours: approx. 24,000 in automatic mode Fsbu Uc Uowigb Te Eegb Euromap 67 Robot interface Air valve x 2 Hydraulic core pull x 1 Injection unit is wear-resistant and resistant to corrosion Main engine of the machine - servo motor driven by inverter - energy saving Proportional valve on the injection unit - precise injection There is a possibility of purchasing the machine with a robot or manipulator Dimensions: Weight: 4100 kg Length/width/height: 4.18x1.42x2.18 m Drive: Pumps/motor: 15 kW Heating power: 10.4 kW Total power: 25.4 kW All machines offered are started by our service technicians before sale. It is possible to receive a video of the technical tests of the selected machine or to take part in live technical tests in our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2005, Boy 35A VV Year of construction: 2005 Injection unit: Screw diameter: 28 mm Injection weight: 55.8 g Injection pressure: 1577 bar Dosing volume: 58.5 ccm Clamping unit: Clamping force: 35 t Distance between tie bars: 280x254 mm Size of the clamping plates: 0x0 mm Ejector: hydraulic Clamping unit: hydraulic Control system: Procan CT - touchscreen Additional equipment: Euromap 12 Robot interface Air valve x 2 Hydraulic core pull x 1 Hardened injection unit - bimetal Dimensions: Weight: 1350 kg Length/width/height: 2.06x0.95x2.74 m Drive: Pump/motor: 7.5 kW Heating output: 5.8 kW Fgjbu Ucswif Tne U Eob Total output: 13.3 kW All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request