Used Weiss Wm460A X 1500 Mm for sale (119)

Condition: excellent (used), Weiss Technik TS 60 Thermal Shock Test Chamber / 60 L, –71…+220 °C Water-cooled Item description: For sale is a Weiss Technik TS 60 Thermal Shock Test Chamber. The chamber is ideally suited for rapid temperature cycling tests (e.g., per IEC, MIL-STD, JEDEC) and has been well maintained. Volume & internal dimensions: Test volume: 60 liters Internal basket/test room dimensions (W × D × H): approx. 380 × 430 × 370 mm External dimensions (W × D × H): 895 × 1970 × 1895 mm Temperature ranges & cycling: Hot chamber: +50 °C to +220 °C Cold chamber: –72 °C to +70 °C Transfer time (basket between both zones): < 10 seconds Heating rate / speed up to 17 °C/min Cooling rate / speed up to 3.7 °C/min In single mode (cold zone only), heating rate: approx. 3.2 °C/min Ndsdpfxoxr A R To Ad Tod Temperature deviation & uniformity: Temporal deviation (temperature control over time): ± 0.3 to ± 1.0 °C Load / permissible weight & lifting system: Basket/lifting system load capacity: 20 kg maximum load Transfer basket secured by safety grilles on all sides Additional features & equipment: Noise level: approx. 58 dB(A) in operation Control: Touchscreen, RS-232 / USB / Ethernet interfaces Electrical connection: 3/N/PE AC 400 V ±10% 50 Hz Rated power: approx. 8.5 kW Rated current: approx. 25 A On-site protection: 32 A Refrigerants: R-404A / R-23 Weight: 800 kg Important safety information for buyers! The following steps are carried out on our offered chambers prior to sale: 1. Functional check and replacement of necessary components 2. If required, refilling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (see picture) (Technical data subject to change and errors reserved!) For further questions, feel free to contact us by phone.

Condition: used, Second hand line by TANG OG WEISS AS (DK) for packaging liquids into plastic bottles. Volume range from 50 ml to 750 ml. Working output of line: - for bottles volume 750 ml - up to 600 pcs/h - for bottles volume in range from 200 up to 400 ml - in range from 800 - 900 pcs/h, - for smaller volume bottles it is possible to assume a capacity in the range of 1000 to 1200 pcs/h. Nedpfx Aexw Tgpsd Tjdd The line consists of: - Container of bottles produced by PACKFEEDER S.L. (Spain) model MN 100-4, - Filling-closing unit manufactured by TANG OG WEISS AS (DK) model TWKS. It includes filling module by TANG OG WEISS AS model TWRF, with two filling nozzles, stainless steel buffer tank with total volume 15 l, rotary table, caps feeder, arm for capping/cap tapping and plate conveyor, - Stainless steel lobe pump manufactured by SSP PUMPS (England) model L2-0017, for feeding the product to the buffer tank, - Labelling unit, by EME Etiketteringsmaskiner ApS. (Denmark) model 4-120 (4000 series) without printer, equipped with a plate conveyor, two pieces of self-adhesive label applicators (front and back of the packaging). Label feed height range: from 20 mm to 120 mm, label feed width range: from 10 mm to 250 mm, operating speed: 0-40 m/min, - Automatic packaging machine in heat-shrinkable film by SKINETTA PAC-SYSTEME GMBH & CO. (Germany) model ASK 450. The device wraps packages of 6 bottles with film and thermoform it. The entrance opening to the foil shrinking section has the following dimensions: width 440 mm, height 320 mm (year of manufacture 1994, no documentation), - Plate conveyors and control panels. The equipment includes a cabinet with formats for oval bottles with volumes: 50 ml, 200 ml, 400 ml, 750 ml, as well as manufacturer's documentation in Danish and a user manual in Polish. The line was produced in 2007.

Condition: new, Weiss 178377 grinding spindle 21kw / 7000 rpm = 0001, unused, 100% functional, scope of delivery as per photos ATTENTION: Please enquire for charges for packing and transport separately! ATTENTION: Please enquire for charges for packing and transport separately! Ndedpfx Adoxtwcgj Tjd

Year of construction: 2011, operating hours: 3,210 h, condition: excellent (used), Climate test chamber, climate chamber, temperature test chamber WKL 34/40 by Weiss Umwelttechnik Test chamber volume approx. 34 liters Internal dimensions approx. 340 x 310 x 280 mm 1 shelf Test chamber lighting: halogen Power: 1.8 kW, 230 volts 0.8 kg refrigerant R404A Temperature range: -40 to +180°C Humidity range: 10 to 98% rH Water tank for 13 liters of demineralized water Simpati control system, color touch display Test programs in automatic mode or manual for temperature and humidity only CE mark Very well-maintained heating chamber from prototype production in the motorsport department of a Wolfsburg-based automobile manufacturer. Only 3,210 operating hours. Unfortunately, no key available. Ndodpfow U U Nhex Ad Ted Dimensions approx. 580 x 950 x 980 mm (L x W x H). Weight approx. 190 kg. The machine can be demonstrated on site by appointment. We only offer machines that are ready for demonstration in our warehouse; see 'More offers from this seller.'

Condition: used, Year of construction: 2012, Motor: 0.75 kW Technical data: see illustration. Ndedpfx Adexcty Ts Tjd

Condition: used, Year of construction: 2008, Here are some key details: - CNC universal cylindrical grinding machine WUG 21 base machine by CNC-Technik Weiss. (The WUG 21 features a Karstens machine bed on which the CNC system is mounted.) - Year of manufacture: 2008 / operated in single-shift use only - 1000 mm between centers - Workpiece spindle headstock and tailstock MK4 Nodpfxexmurxs Ad Tsdd - Wheel diameter up to 500 mm - Wheel mounting at a 26.5° angle - Grinding wheel drive with programmable SUG - Grinding spindle headstock manually swivellable on air cushion - Wheel positioned on the right - Internal grinding attachment mounted at the rear, including dressing device - Eckelmann control system - DIN programming - Cycle programs - Manual grinding: yes - Automatic dressing - Marposs acoustic emission monitoring for external grinding wheel, including software package - Grinding wheel spindle and workpiece spindle driven by V-belt drive

Condition: good (used), Year of construction: 2010, Rotary table Fabr.WEISS Type: TC 220T Year: 2010. Ndedpjxr Dh Hefx Ad Tsd

Condition: new, Center length ----- 500 mm Center height ----- 125 mm Turning diameter above bed ----- 250 mm Turning diameter above slide ----- 150 mm Spindle intake ----- MK4 Passage of main spindle ----- 26 mm Bed width ----- 140 mm Spindle speed ----- 80-1600 rpm Loose head ----- MK3 Motor ----- 750W Ndodpfx Adopz Iy Ao Tod Lathe equipped with automatic longitudinal and transverse feeding Includes: lower case, 3-jaw chuck, 4-jaw chuck, chuck, fixed goggles, moving goggles, CE shield

Condition: new, Weiss W-175229B / 175229B grinding spindle SN: 175229B-0033, unused in original packaging, 100% functional, scope of delivery as per photos ATTENTION: Please enquire for charges for packing and transport separately! ATTENTION: Please enquire for charges for packing and transport separately! Nsdpfx Asxtwctsd Todd

Condition: as good as new (ex-display), Year of construction: 1997, machine/vehicle number: 1MB241H-6D-A111-A1, spindle speed (max.): 5,000 rpm, input voltage: 380 V, overall weight: 400 kg, power: 18 kW (24.47 HP), Spindle from Weiss GmbH, type 174405B, year of manufacture 1997. Unused, stock. For further details see type plate / pictures. Ndjdpfx Aetq H Suod Ted Packaging and loading included.

Condition: used, Year of construction: 2012, Motor: 0.75 kW Technical data: see illustration. Ndodpsxctw Sofx Ad Ted

Condition: excellent (used), CATALOGUE NUMBER: 6943 TECHNICAL DATA - Feed hopper inlet: 1600x1500mm - Rotor working width: 1500mm - Main motor: 45kW - Pump motor: 5.5kW - Number of knives: 44 pcs - Knife dimensions: 50x50mm - Screen: 59mm - Pusher drawer - Auto-reverse - Dimensions (L/W/H): 3430x2800x2850mm - Weight: approx. 9000kg ADVANTAGES – French manufacture Ndedpfx Adolnkxws Tod - New knives installed – Auto-reverse – Pusher drawer – Very good condition – Used shredder Net price: 159,900 PLN Net price: 38,070 EUR Net price calculated at an exchange rate of 4.2 PLN/EUR (In case of significant exchange rate fluctuations, the price may change)

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, center height: 200 mm, workpiece weight (max.): 30 kg, grinding length: 400 mm, grinding wheel diameter: 350 mm, total width: 2,600 mm, total length: 1,800 mm, grinding diameter: 100 mm, workpiece weight between centers: 30,000 g, distance between centers: 400 mm, type of input current: AC, spindle speed (max.): 1,000 rpm, spindle speed (min.): 90 rpm, grinding spindle motor power: 3,700 W, grinding spindle speed: 2,000 rpm, overall weight: 2,000 kg, pivoting range: 30 °, input voltage: 400 V, Equipment: rotational speed infinitely variable, General Diameter over table: 200 mm Distance between centers (ABC): 400 mm Grinding length: 400 mm Grinding diameter (max. / min. OD): 100 / 6 mm Grinding diameter (max. / min. ID): 85 / 6 mm Max. weight between centers: 30 kg Max. weight incl. chuck: 10 kg Grinding Spindle Wheel size: 350 x 127 x 50 mm Minimum usable wheel diameter: 300 mm Spindle speed: 1800 – 2000 rpm Spindle motor power: 3.7 kW Nsdpfsxvr Hfox Ad Tedd (Circumferential) speed: 33 m/sec Rapid traverse: 40 mm Rapid traverse with handwheel: 20 mm Max. automatic infeed on diameter: 1.7 [3.4] mm Minimum diameter increment: 0.001 mm Infeed speed on diameter (coarse/fine): 0.015 – 6 / 0.015 – 3 mm/min TABLE Table speed: 0.1 – 5 m/min Table stroke: 450 mm Minimum travel: 2 mm Maximum table swiveling: -2º to +30º Work Spindle Taper bore: MT-4 Spindle speed: 90–1000 rpm Spindle motor power (2 steps): 0.28 / 0.37 kW TAILSTOCK Morse taper: MT-3 Quill stroke: 25 mm Quill offset range (optional): [±0.03] HYDRAULIC UNIT Tank capacity: 40 l INTERNAL GRINDING ATTACHMENT Spindle size (diameter x length (max. rpm)): 60 x 250 mm (18,000 rpm) Spindle housing bore: 60 mm Motor power: 1.5 kW GENERAL Operating voltage: 415 Volt Alternating current, 3-phase Total power requirement: 6.5 [8.5] kW Footprint including standard coolant tank (LxW): 2600 x 1800 mm Machine weight: 2000 kg

Condition: not inspected (used), diameter / mm Cutting (quantity) / weight / kg Spindeltyp: 195.6/S/48-7.7/20-1D/60HSK-A63 Ident-No.: 195.6/x000917B2 Nedpfx Adjxn Aqfo Tsdd Milling spindle is sold as untested !

Condition: new, WEISS 174282-014 spindle, dimensions see acceptance protocol, unused in opened original packaging, 100% functional, scope of delivery as per photos Ndjdpextwb Nsfx Ad Tsd

Condition: like new (used), Year of construction: 2021, WEISS Ltd. used / tested CR heavy duty table with servo amplifier B&R 8V1180.00-2 EXTREME LOADABLE, FOR HORIZONTAL AND VERTICAL 585Kg axial runout : 0,02 mm Radial runout : 0,02 mm Center opening : 346 mm max. dynamic axial force : 70000 N B&R: 8V1180.00-2 Modular mechanical design by plug-in modules Integrated mains filter Nedpfx Ajpa Nz Dsd Tsdd Integrated or optional external braking resistor All connections in pluggable design Integrated electronic restart interlock ACOPOS servo drive, 3x 400-480 V, 19 A, 9 kW, line filter, braking resistor, DC link power supply and electronic safe restart interlock integrated

Year of construction: 2013, condition: used, Rotary Indexing Table Rotary Table Rotary Drive Welding Positioner Positioning Table WEISS TYPE: CR700 CAA Year: 2013 Rotary indexing table/positioning table with control cabinet including frequency inverter and PILZ PLC control. Diameter of mounting plate approx.: 700 mm Diameter of inner collar approx.: 320 mm Height without base approx.: 290/320 mm Base diameter approx.: 1600 mm Base height approx.: 190 mm Max. dynamic axial force: 70,000 N Nedpfxoxdv N He Ad Tjdd Weight approx. 585 kg plus base There are 4 pieces of these rotary drives from Weiss available. For further details or purchase of multiple rotary drives: Please enquire.

Year of construction: 1999, condition: not inspected (used), For sale is a built-in salt spray chamber/corrosion test chamber from Weiss Technik, type: SC/KWT 450 The system must be cleaned and serviced before use. The system can be inspected on site, shipping is possible. Manufacturer Weiss Technik B2misngk99 Type: SC/KWT 450 Test chamber capacity: 480 l Max. load: 100 kg Brine storage tank: 180 l Corrosion tests: Salt spray test: Room temp. up to +50 °C Babumc3umw Condensation water test: Room temp. up to +45 °C Voltage: AC 230V Salt spray test SS: DIN 50021 Njdpexfzttjfx Ad Tedd Condensation water test KFW: DIN 50017 Normal climate (ventilation): DIN 50014

Condition: excellent (used), Center height 180 mm Distance between centers 1000 mm Grinding lenght 650 mm Grinding wheel 500 x 80 x 127 mm + 250 x 32 x 127 mm Nsdevhafdspfx Ad Todd With internal grinding attachement Misc.accessories MARCELS MASCHINEN AG

Condition: used, Year of construction: 2020, operating hours: 6,875 h, machine/vehicle number: IntNr231185, EMAG WEISS cylindrical grinding machine EMAG WEISS type W11-CNC / UNIVERSAL CYLINDRICAL GRINDING MACHINE W 11-CNC SL650 Spindle hours: approx. 6,850 hours Power on hours: 20,422 hours Njdoxiwyqspfx Ad Todd This machine is characterized by its 2 in 1 control concept: 100% conventional cylindrical grinding or switching to 100% CNC cylindrical grinding Technical data: • Control: CNC-controlled (depending on year of manufacture Heidenhain, Siemens or Fanuc) Grinding length max. mm 650 / 1,500; in 25.5 / 59 Centre height mm 200 in 8 Grinding diameter outside mm1 / 390 in 0 / 15.5 Max. weight flying MK 4 kg 100 / lb 220.5 Max. workpiece weight between centres kg 250 /lb 551 Feed: X-axis travel mm 380 / 480 /in 15 / 19 Feed: Z-axis travel mm 1,150 / 1,650 in 45.5 / 65 Grinding wheel diameter mm 400 / 500 in 15.5 / 19.5 Rated power (100% ED) kW 9 / 11 hp 12 / 15 Peripheral speed m/s 20 - 50 Machine equipment: • Grinding wheel drive: Powerful Motor for precise grinding results • Tailstock: Adjustable tailstock for different workpiece lengths • Workpiece holder: Chuck or centering points (depending on the application) • Coolant system: Integrated, to avoid overheating and for optimal grinding results • User-friendly interface: Intuitive CNC user interface for easy programming and control • Measuring systems for real-time monitoring and quality assurance • Machine bed Cast bed Karstens base with high static-dynamic rigidity • X-axis High-precision linear guides, ball screw and glass scale • Z-axis V-flat or linear guides, ball screw and glass scale • Control Touch screen with integrated CNC control based on Windows Dialog programming, DIN programming, program memory. • Technical equipment Electrical cabinet according to VDE with CE mark • Coolant system and extraction system • Paper belt filter system with 250 | Container • Mechanical fume extraction with 1600 m²/3 with control without support foot • Measuring axis for moving to multiple diameters with wide range • Measuring head. Measuring position freely programmable. • Prepare robot interface. • Only provide 10 x l / O without interface plug software and PLC Applications: • Cylindrical external and internal machining • Precision grinding for mechanical engineering, the automotive industry and toolmaking • Production of shafts, bushings, rollers and other rotationally symmetrical workpieces Special features: • High rigidity of the machine body for vibration-free work • CNC control for complex grinding cycles and flexible processing • Adaptation to customer-specific requirements possible Optionally retrofittable Equipment: • Automated loading and unloading systems • Special mounts and special grinding wheel holders Optional grinding wheels available: • See photos The machine can be inspected by appointment. Subject to changes and errors in the technical data and information as well as prior sale! EMAG WEISS Cylindrical Grinding Machine EMAG WEISS Type W11-CNC / UNIVERSAL CIRCULAR GRINDING MACHINE W 11-CNC SL650 Spindle Hours: approximately 6,850 hours Power On Hours: 20,422 hours 2 in 1 control concept characterizes this machine: 100% conventional cylindrical grinding or switch to 100% CNC cylindrical grinding Technical data: - Control: CNC-controlled (Heidenhain, Siemens or Fanuc, depending on year of manufacture) Grinding length max. mm 650 / 1,500 ; in 25.5/59 Center height mm 200 in 8 External grinding Ø mm1 / 390 in 0 / 15.5 max. weight fl

Condition: new, Weiss 178377 grinding spindle 21kw / 7000 rpm = 0002, unused, 100% functional, scope of delivery as per photos ATTENTION: Please enquire for charges for packing and transport separately! ATTENTION: Please enquire for charges for packing and transport separately! Ndedpfx Ajxtwcmod Tjd

Condition: excellent (used), Year of construction: 2016, We offer here a used rotary indexing table of the brand Weiss. The turntable has a load capacity of approx. 30 tons and a diameter of approx. 3.5m as well as a dead weight with motor of approx. 6500Kg. The control of the turntable is also available, with SEW frequency converter, braking resistor etc.. Ndjdpjni Awpjfx Ad Tod All documentation is available.

Year of construction: 1997, condition: excellent (used), Safety work table Make WIBO White type Jekt TCRJO 180/98 with gradation made of stainless steel working space : Nsdjhk St Aopfx Ad Tjdd Depth 920 mm height 1200 mm width 1800 mm working height 600 mm total dimensions : Depth 1080 mm height 2100 mm Height with suction 2550 mm width 1800 mm

Condition: new, Motor ----- 900W - 230V - 1Phase / 900W - 400V - 3Phase Speed ----- 2950 O/min Stone dimensions ----- 200 x 32 x 32 mm Nedpfxoga Tw Uo Ad Todd Coarse stone grain 36 Fine stone grit 80 Safety class ----- IP40 Weight ----- 25 kg OPTIONS * Base cabinet

Condition: new, Weiss 175342 spindle motor designation mW13.5/15.5-4 DBL.311002 EN60034, unused, 100% functional, scope of delivery as per photos ATTENTION: Please enquire for charges for packing and transport separately! ATTENTION: Please enquire for charges for packing and transport separately! Nsdpextwcaefx Ad Todd