IMA SX TRIMMING UNIT

IMA

Condition: used, Year of construction: 2008, power: 41 kW (55.74 HP), edge thickness (max.): 3 mm, controller model: ICOS OPEN, The machine has the following configuration: Pre-milling unit Manufacturer model: R3 L20 Engagement control: Automatic, time-controlled Motor power: 4 kW Speed: 9,000 rpm Edge processing Number of edge processing units: 10 Crosscut saw unit Manufacturer model: 8.42/39/B Number of motors: 2 Motor power: 0.6 kW Speed: 12,000 rpm Flush trimming and rounding unit Manufacturer model: 08.055 Number of motors: 0.6 (?) Motor power: 1 kW Speed: 12,000 rpm Corner rounding unit Manufacturer model: 08.342 Number of motors: 2 Motor power: 0.66 kW Speed: 12,000 rpm Scraper blade unit Manufacturer model: 08.50 Belt sanding unit 1 Manufacturer model: 08.62 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 2 Manufacturer model: 08.062 Motor power: 0.18 kW Hedpfx Aezmtkaeh Eonr Speed: 1,400 rpm Belt sanding unit 3 Manufacturer model: 08 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 4 Manufacturer model: 08.617-2 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 5 Manufacturer model: 08 Processing unit 10 Manufacturer model: 08.190 Motor power: 4.5 kW Speed: 9,000 rpm TECHNICAL DETAILS Workpiece dimensions Max. panel height: 60 mm Min. panel length: 130 mm Min. panel width: 65 mm Edge material Min. edge thickness: 0.4 mm Max. edge thickness: 3 mm Feed Max. feed rate: 30 m/min Pressure: Rubber belt Number of panel sizing/milling units: 1 MACHINE DETAILS Control system: ICOS OPEN Total connected power: 41 kW EQUIPMENT Number of panel sizing/milling units: 1 Lamps for preheating the panel side Edge roller magazine with 2 positions PUR pre-melting unit Pressure roller set with 5 pressure rollers Spraying unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at its destination. External reference: 5657

Condition: used, Year of construction: 2003, Single-sided edge trimming and gluing machine Manufacturer: IMA Type: AVM/K/I/G80/822/S3R3L20 Year of manufacture: 2003 For milling, edge gluing, and finishing for a standard groove - only for pre-shaped/pre-grooved doors and square-edged doors Left-hand machine (fixed stop on the left). Complete processing in 3 passes 1st pass: Processing of the top surface of the door (transverse processing) 2nd pass: Door long edge 3rd pass: Door long edge During the 2nd and 3rd passes, the protruding transverse edge from the 1st pass is milled off by using a co-rotating/counter-rotating milling process. Double groove gluing is only possible through modifications to the machine and subsequent manual finishing of the edge. Max. door thickness: - Straight edge: approx. 70 mm - Groove gluing: approx. 60 mm Stable machine frame as a support for aggregates and housing for electrical installation. Drive for feed speeds of approx. 5-25 m/min., mechanically infinitely adjustable. (not to be confused with processing speed) Continuous, plastic-coated strip-type conveyor chain, approx. 80 mm wide, with automatic central lubrication. Manually height-adjustable top pressure with a V-belt 80 mm wide and spring-loaded, ball-bearing guide rollers. Machine length approx. 10,900 mm Infeed table at the machine inlet. 1 horizontal, manually adjustable, unheated stop bar 1 joiner milling unit controllable, not swiveling, without sensing with 2 motors, each 3 kW Gluing unit for optional operation of straight edge or softforming gluing, by changing the glue application. Edge material: - Strips: up to 1.3 mm - Roll material: 0.4-3 mm - Solid wood strips: 6 mm Strip length max.: 2550 mm Strip height: 14-80 mm (depending on glue application) with: - Side adjustment by hand for the pneumatically controlled glue application. - Height adjustment by hand -15mm downwards and up to +10mm upwards. 1 bell for the main pressure roller, Hnsdpfx Aezuykvjh Ejr manually adjustable 1 glue application 0.8L, max. edge height 70mm, straight edge with pneumatic quick-release, Chem-Coat coated, electronic temperature control 1 hot melt glue application 0.8L with quick-release, up to max. 80 mm high edge material, soft edge, Chem-Coat coated, with temperature control and control unit for the strip coating 1 automatic Quickmelt hot melt glue feeder with a heating power of 5.0 kW 1 2-fold magazine only for edge material up to 3.0 mm thick, can be manually attached to the single-roll magazine 1 groove forming pressing unit for pressing the edge material into the groove with: - an activation unit 15 kW for re-activating the edge material for groove forming - a pneumatically controlled forming shoe for the underlapping edge - a pneumatically controlled forming shoe for the entire groove - additional post-pressing rollers for the edge areas in the groove - an electro-pneumatic lateral retraction device for the entire pressing unit 1 horizontal adjustment with mechanical digital display 1 trimming unit for 2 motors mounted on the top pressure for trimming the front and rear edge/strip overhang, for trimming cuts flush or with a bevel. 1 milling unit for 2 motors with height sensing, side sensing, for pre-milling from below and above with 2 motors 1kW, 400V, 200Hz, 12,000 RPM, 30° swiveling 1 milling unit for 2 motors with height sensing, side sensing, for fine milling from below and above with 2 motors 660W, 400V, 200Hz, 12,000 RPM, 30° swiveling Note: The technical data and descriptions are copies of the original order

Condition: used, Year of construction: 2009, Edge banding machine Manufacturer: IMA Type: Novimat/I/G80/650/R3 Year of manufacture: 2009 Technical data - Workpiece overhang from the chain conveyor: 38 mm - Feed width: min. 65 mm (with max. workpiece thickness of 25 mm) - Workpiece length in feed direction: 150 mm - Overall height (top edge of chain conveyor): 960 mm - Feed speed: approx. 6 - 30 m/min, electrically adjustable - Machine control system ICOS open compact Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65 mm - Workpiece thickness: 8 - 40 mm (with edge trimming function) / 60 mm (without edge trimming function) - Smallest workpiece: 150 x 150 mm or 65 x 300 mm - Edge material: paper, plastic and veneer - Height: 14 - 65 mm - Roller material thickness: 0.3 - 3.0 mm (veneer edges limited to max. 1.0 mm) - Max. upper edge overhang: 5 mm Units Infeed area - Release agent applicator mounted at the top and bottom, not adjustable Edge trimming - 2 motors 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function Hnedpfx Ajzuyi Ejh Esr - Motor 1 counter-rotating - Motor 2 co-rotating Gluing unit VTG 3-6 - with one preheating nozzle 300 mm for preheating the workpiece edge - 6-position edge magazine for roller material 0.3 - 3 mm thick. - 1 driven main pressure roller and 4 pressure rollers, with scraper, pneumatically adjustable Glue application - with pneumatic quick-lock system - Chem-Coat coating - electronic temperature control - Volume 0.8 l Pre-melting tank approx. 1 l - Heating power 3 x 400 W - with EVA glue, approx. 7.0 kg/h - with filler-free glue, approx. 5.0 kg/h Cutting unit - 2 motors 660 W, 200 Hz - incl. frequency inverter with braking function - pneumatic pivoting 0+25 for straight and bevel cutting Flush trimming - 2 motors each 1000 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function Multi-profile trimming unit - 2 motors each 660 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function - for trimming 4 profiles - with stepper motor axes for horizontal and vertical positioning Contour trimming unit KFA x30 - 1 motor 500 W, 400 V, 400 Hz, 18000 rpm - Program-controlled conversion for up to 4 profiles - incl. fine positioning for different edge thicknesses Multi-profile scraping blade - Stepper motor axes for horizontal and vertical positioning - Scanning from above and below (max. 4 profiles) - Scanning from the side via pneumatic pressure Spray nozzles at the top and bottom for applying cleaning agents - fixed, not adjustable Surface scraping blade - with height sensing skid - electronically controlled horizontal positioning Buffing unit - 2 lower and 2 upper motors, 180 W, 50 Hz, 1400 rpm - 1st motor pair with cloth-sisal discs 50x160x19 mm - 2nd motor pair with polishing discs 50x160x19 mm - The motors operate in the same direction and are both tilted and pivoted in the feed direction. - Each motor can be individually adjusted vertically 2x NC-controlled grooving - 2 milling motors each 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function - one manual 90-degree pivoting device from 180 -270 with co- and counter-rotating function - Horizontal, stepless adjustment with AC servo motor for grooving unit Workpiece return Note: The technical data and descriptions are copies of the order confirmation at the time. The information is for informational purposes only and is non-binding.

Condition: used, Year of construction: 2005, Edge banding machine Manufacturer: IMA Type: Advantage 600 Year of manufacture: 2005 Technical data Hedpfx Ahszuyirs Ejnr - Joint milling - Gluing unit for thin and thick edges - Imprint zone - 2x edge trimmers - Flush trimming - Multi-function trimming unit (MFA) - Profile trimming blade - Surface trimming blade - Buffing - Return system at the upper pressure roller Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2005, Single-sided edge banding machine Manufacturer: IMA Type: Novimat Systems/I/R75/1000 Year of manufacture: 2005 Technical data PC control - ICOS OPEN control system Feed rate 5-25 m/min, frequency-controlled Fence with electronic positioning control Adhesive application above and below Trimming unit with 2 motors, each 4.5 kW, 9,000 rpm, controllable. - Horizontally adjustable via axis Heating element approx. 300 mm long, 2x 1.5 kW Gluing unit - Adhesive application with pneumatic quick-lock system. - Automatic PU melting system Quickmelt for 2 kg cartridges - 32-position edge magazine (8 slots up to 3 mm / 24 slots up to 1.3 mm) Vertical roller holder for 32 rollers, max. diameter 850 mm Cutting unit on the upper pressure roller with 2 motors, each 200 W, 400 V, 12000 rpm. - Horizontal pneumatic swiveling 0-25 - With controllable side contact, for 3 edge thicknesses Trimming unit with 2 motors, each 1000 W, 400 V, 200 Hz, 12000 rpm. - Operating in counter-rotation. Multi-processing unit 08.348 - For chamfering or radius trimming of the upper and lower longitudinal edges, as well as for copying the front and rear workpiece edges. - Program-controlled adjustment for up to 4 profiles - 2 motors, each 660 W, 400 V, 200 Hz, 12000 rpm. Spray nozzles above and below for applying cleaning agents Multi-profile scraper unit - With stepper motor axes for horizontal and vertical positioning. - For 4 profiles. Straight scraper unit - With electro-pneumatic retraction device Hnedpfjzuyhnjx Ah Ejr Copying edge smoothing unit - With 4 smoothing motors, each 250 W - Smoothing unit with 2 lower and 2 upper motors, each 180 W, 50 Hz, 1400 rpm. Smoothing unit - For smoothing and eliminating the white haze on the trimmed PVC/ABS edges - With an upper and lower smoothing zone With workpiece return system LGIMATECH ZHR 05/L/145 - Air cushion table, inclined, 2 return belts with brushing devices from below. Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, - X = 2 x 2,400 - Y = 1,800 mm - Main spindle 12 kW - 18-position tool changer - Gluing unit with 6-position coil magazine Used CNC machining center Manufacturer: IMA Type: BIMA P 480 V, 180/480 Year of manufacture: 2001 Alternative processing: - X = 2 x 2,400 - Y = 1,800 mm - Main spindle 12 kW - 18-position tool changer - Gluing unit with 6-position coil magazine Working area: For standard machines, Y = 1,800 mm Changing table area for alternating machining: X = 2 x 2,400 mm / Milling and drilling X = 2 x 2,100 mm / Gluing CNC line control IMATRONIC NT 231 Automatic adjustment table with clamping plates Main spindle 12 kW With integrated C-axis, 360 degrees Automatic tool/adapter unit changer, 18-position 1 edge banding unit VT100 With glue application device Edge thickness: 0.4 - 3 mm For 4-sided edge banding and all-round edge banding with butt joint 6-position roller magazine 1 trimming unit 0.8 kW Including adapter unit Hnedpfjzux Uajx Ah Eer - Saw, fixed at 90 degrees - Horizontal milling unit (corner release) - Chamfer milling unit - Straight milling unit - Profile drawing blade Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2008, - Machining area 4300 x 1250 mm - 8 pcs. workpiece supports - Main spindle 7.5 Kw / 11kw - Vertical drilling unit - Horizontal drilling unit - Dado cutter - Tool changer for 18 positions CNC machining center Manufacturer: IMA Type: Bima 300 Year of manufacture: 2008 Technical data - Machining area 4300 x 1250 mm - 8 pcs. workpiece supports - 1x Main spindle 7.5 Kw / 11kw (S1 / S6) HSK F63 1500 - 18000 rpm - Horizontal drilling unit - Vertical drilling unit - Dado cutter - 2x Vacuum pump, each 90 m³/h Hodpfxszux Tio Ah Eenr - Safety mats - IMA Wop software + office license

Condition: used, Year of construction: 2012, - Machining area: 5300x1400 mm - Main spindle replaced 3 years ago - 18-position tool changer Technical data Machining area - In the X direction: 5300 mm - In the Y direction with main spindle + WZ-0: 20 mm: 1400 mm - In the Y direction with drilling unit: (all vertical drills) 890 mm - Single-position machining: X = 2 x 2550 mm - Free space in the center: X = 200 mm - Alternating field machining: X = 2 x 2250 mm - Free space in the center: 800 mm 1 automatic tool/adapter changer magazine - Arrangement: mounted on the support, moving in the X direction - Disc changer with 18 magazine positions Guidance system - All axes are equipped with pre-tensioned, surface-hardened precision roller guides. Central lubrication - Manual central lubrication for all main axis linear guides and Z ball screw. 1 vacuum pump, 90 m3/h Console table consisting of: - 2 work piece stops fixed on the right and 2 on the left in the X direction, for movement in the Y direction - 10 adjustable support arms in the X direction, each with a rear stop - All stops are controlled by the program - The suction plates are fixed via the patented 2-circuit clamping system, eliminating the need for hoses. - 8 smooth support rails, automatically retractable - 2 push buttons for the workpiece clamping/releasing function Additional 2nd vacuum pump, 90 m3/h 1 additional central stop row, for centering workpieces Chip conveyor 1 main spindle - Drive power: 10.0 kW in S-6 operation - 7.5 kW in S-1 operation - Tool holder: HSK F63, taper diameter = 38 mm, similar to DIN 69893 - Speed range: infinitely variable RPM, programmable 1 centrally integrated CNC axis, rotating 360 degrees - for all adapter units, with torque support on the main spindle and pneumatic interface 1 vertical drilling unit l14 with 6 spindles, horizontal and attachment unit for a dado cutter - Horizontal drilling units with 2 outputs each Attachment unit for a dado cutter - Swivel range: 0 or 90° Hnsdpfezuw Rtox Ah Eer Control system ICOS CNC Modern, powerful PC-based control system with: - User-friendly interface with Windows standards - Trajectory control of all servo axes - Job list / order processing - IMA backup and recovery system on two hard drives - Uninterruptible power supply (UPS) IMAWOP software package - for dialog-oriented creation of CNC machining programs - - 3D view and basic simulation of the programmed workpiece, the suction cups and consoles including tool and adapter display.

Condition: used, Machining area: - in the X direction without gluing 6000 mm - in the X direction with gluing 5000 mm - in the Y direction 1200 mm - in the Y direction with main spindle + center distance 20 mm 1300 mm max. workpiece height above - top edge of suction plate Z1 100 mm - max. workpiece thickness Z2, dependent on equipment/application Work table height: approx. 950 mm 1 main spindle with pneumatic feed stroke - drive power: 12 kW in S-1 operation - tool holder: HSK F63, taper diameter = 38 mm - tool change: automatic - change force: 11000 N - tool weight: max. 6 kg - direction of rotation: clockwise/counterclockwise, programmable - speed range: continuously variable 1500 - 24000 rpm, programmable - drive: frequency-controlled three-phase motor - spindle lubrication: single grease lubrication - spindle cooling: water cooling 1 CNC axis rotating 360 degrees 1 vertical drilling unit S21 Machine table consists of: - 6 support arms adjustable in the X direction, each with a rear and center stop, all stops controlled by the program - 6 sets of suction plates consisting of a total of - 6 suction plates 114 x 159 x 100 mm - 6 suction plates 125 x 75 x 100 mm - The support arms and suction plates can be individually positioned according to the corresponding workpiece size. Changeover area: - without pendulum machining, without gluing: X = 2 x 2900 mm - free space in the middle: X = 200 mm - without pendulum machining, with gluing: X = 2 x 2150 mm - free space in the middle: X = 700 mm - with pendulum machining, without gluing: X = 2 x 2400 mm - free space in the middle: X = 1200 mm - with pendulum machining, with gluing: X = 2 x 1700 mm - free space in the middle: X = 1600 mm Feed drive system Rapid traverse rates: - X-axis 100 m/min - Z-axis 25 m/min Air pressure: 6 bar Tool changer magazine with 18 positions Tool coding: position-coded Tool weight: max. 6 kg Tool length: max. 150 mm Tool diameter: max. 100 mm when fully loaded max. 150 mm with free adjacent positions or nesting Central connection for extraction Hnsdpfx Ahszupibe Eor Mains voltage: 3/N/PE, 400/230 V, 50 Hz 1 vacuum pump 100 m3/h

Condition: used, Used IMA model VORTEX 075 stainless steel high share mixer/granulator. - Manufacturer: IMA - Model: Vortex 075 Hnsdpfxszun Hxj Ah Eer - Vessel capacity: 85 litre total capacity, working capacity min/max 8/40 kg - Vessel lid and outlet valve are pneumatically operated - Includes: local control panel and switchboard Mixing system: - Impeller agitator is driven by 3,0 kW motor, maximum speed 118 rpm - Chopper is driven by 1,5 kW motor, speed 3000 rpm Weight: Actual: Kg550.0