Chain plates

IMA

Condition: used, machine/vehicle number: 008662, Position 1: Single Edgebanders IMA-NOVIMAT CONTOUR I/G80/790/R3 Kedpfxezmmtne Afkedr Position 2: Panel Return Systems IMA-NOVIMAT CONTOUR I/G80/790/R3

Condition: used, Door panel postforming line Note: The line began series production in 2022; at this point, all machines were technically synchronized and, if necessary, overhauled. Door panel postforming line consisting of: Portal loading system Manufacturer: Kraft Year of manufacture: 2019 Technical data - with vacuum lifter - 2 infeed roller conveyors - one transport roller conveyor for further transport Wide belt sanding machine Manufacturer: Costa Kjdpfx Aezuziyefksdr Type: KK7 CT CT 1350 Year of manufacture: 2018 consisting of: Wide belt sanding machine, sanding from below Technical data - contact roller - electronic shoe sanding unit - cleaning brush - intermediate transport belt, length approx. 3000 mm Wide belt sanding machine, sanding from above Technical data - identical equipment Complete formatting, laminating and postforming line consisting of: Roller conveyor system Manufacturer: Kraft Year of manufacture: 2019 Technical data - 3 individual elements - centering station Double end profiler Manufacturer: IMA Type: FBA/II/740/A Year of manufacture: 2018 Technical data - equipped with infeed conveyor and aligning station - saw unit below - trimming unit - edge trimming unit - prism milling cutter - joint milling cutter - cross edge milling unit - 3 profile milling units - brushes Laminating line consisting of: Infeed conveyor Manufacturer: Kraft Year of manufacture: 2019 Glue application machine Manufacturer: Bürkle Type: DAK1300 Year of manufacture: 1992 Technical data - mechanically overhauled in 2018 - control system completely overhauled in 2022 - with infeed table, manufacturer Kraft - steel platform with stairs and various pumps - glue melting unit GWK Eco 03A Infeed table for laminating line Manufacturer: Kraft Year of manufacture: 2019 Laminating line Manufacturer: Bürkle Type: EKMH 1300 Year of manufacture: 1998 Technical data - new Siemens Simatic KMG Touch control system - Bürkle GLK press calender - incl. film holder and saw for overhang - working width 1300 mm - 2 temperature control units GWK - column swivel crane for loading paper rolls - extraction conveyor Postforming line Manufacturer: Homag Technical data - infeed table - with 2 saw units, horizontal and vertical - intermediate buffer with 4 levels - infeed to the postforming machine - 2 identically constructed processing sides with glue application - PU pre-melting unit Nordson / VersaBlue, year 2020 and 2004 - pressure zone with revolving magazine for various profiles - various milling units and flap brushes - 2 cooling units BEKO Bekoblizz LC, year 2020 Belt conveyor with inspection system - swivel arm with vacuum suction cup - inspection station for optical inspection of the workpiece Portal destacking system Manufacturer: Kraft Technical data - with vacuum portal and 3 destacking stations Note: The technical data and descriptions are copies of the original order confirmation. The information provided is for informational purposes only and is non-binding.

Condition: used, Factory-reconditioned edge processing line for 3 mm edges Manufacturer: IMA Type: Combima Consisting of: Machine 1: Used edge processing machine from IMA, type COMBIMA Factory-reconditioned with a 12-month warranty - Working width max. 1,500 mm, edge thickness approx. 0.3 - 3 mm - Rolling needle bearing chain, drive with 3 kW motor, steplessly adjustable from 9 - 45 m/min - Motorized width adjustment with electronic setpoint and actual value display - Double trimming unit with 2 motors, 4.4 kW, 100 Hz - Milling unit with 1 motor, 4.4 kW, 100 Hz - Hot melt adhesive unit with 2-roller magazine and automatic Quickmelt hot melt adhesive feed - Trimming unit with 2 motors, 0.4 kW - Pre-milling and flush milling unit with 2 motors, 1.5 kW - Chamfering unit with 2 motors, 0.6 kW - Profile drawing blade unit - Straight drawing blade unit - Edge sanding/buffing unit - Beckhoff control system with screen - Electronic converter 100 Hz, manufacturer: KEB - Electronic converter 200 Hz, manufacturer: KEB - 1 used rotating device for changing from longitudinal to transverse - Factory-reconditioned with a 12-month warranty - Max. panel length 2,500 mm, max. panel width 1,500 mm Machine 2: Used edge processing machine, manufacturer: IMA, type COMBIMA Factory-reconditioned with a 12-month warranty - Working width max. 3,000 mm, edge thickness approx. 0.3 - 3 mm - Rolling needle bearing chain, drive with 3 kW motor, steplessly adjustable from 9 - 45 m/min - Motorized width adjustment with electronic setpoint and actual value display - Protective milling unit with motor 3.3 kW, 100 Hz - Double trimming unit with 2 motors, 4.4 kW, 100 Hz - Enclosed gluing unit with double roller magazine and automatic Quickmelt hot melt adhesive feed - Trimming unit with 2 motors, 0.4 kW - Pre-milling and flush milling unit with 1 upper and 1 lower motor, 0.4 kW - Chamfering unit with 2 motors, 0.4 kW - Copy milling unit with 2 motors, 150 W - For milling off strip overhangs on front and rear lower workpiece profiles, copy milling unit with 2 motors, 150 W - For milling off strip overhangs on front and rear upper workpiece profiles, profile drawing blade unit - Straight drawing blade - Buffing unit - Center support - Pull-out rollers 800 mm - Beckhoff control system with screen Kodpfxjzuyqve Afkodr - Electronic converter 100 Hz, manufacturer: KEB - Electronic converter 200 Hz, manufacturer: KEB Delivery time after order placement approx. 4-6 months (depending on current workload and scope of desired work). Individual machine configurations are possible according to customer requirements, as the machines are disassembled down to the base frames and reassembled after replacing all wear parts.

Condition: used, Year of construction: 2010, - Release agent application, top and bottom - Scoring saw with 2.2 kW motor - Trimming unit with 8.0 kW motor - Double milling unit with 2 motors, each 4.5 kW - Gluing unit - End trimming unit - Flush trimming unit - Multi-function unit - Multi-profile edge trimming unit - Spray nozzles, top and bottom - Flat edge trimming unit - Buffing unit - Grooving unit Double-sided edge banding machine Manufacturer: IMA Type: Combima/II/390/B/L12 Year of manufacture: 2010 For longitudinal and transverse feed - 2 low-maintenance precision roller chains with 75 mm wide and 85 mm long, rubber-coated chain plates, with cams - Spacing 1080 mm. Pneumatically adjustable to heights of 8, 16 or 24 mm. ICOS OPEN control system - Max. feed width 3,300 mm - Program-controlled master + slave width adjustment - Fixed stop on the left in feed direction Workpiece dimensions - Min. feed width 244 mm (for longitudinal processing) - Max. workpiece width (chain extension) 1,300 mm - Min. workpiece thickness 8 mm - Max. workpiece thickness 45 mm (with copying function) / 60 mm (without copying) Edge material: Ksdpfjzuyqisx Afkjdr - Min. height 14 mm, max. height 65 mm - Roll material min. thickness 0.3 mm, max. thickness 3 mm Strips and edgebanding: - Min. thickness 0.8 mm, max. thickness 12 mm Feed speed - 10 - 50 m/min. with frequency-controlled drive. Infeed device - with 5 top-mounted, inclined and driven rollers. Center support with roller track - automatically lowerable and automatically centering. Equipped on each side with: Release agent application, top and bottom Scoring saw with 2.2 kW motor, 100 Hz, 6,000 RPM, pneumatically controlled. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Trimming unit with 8.0 kW motor, 100 Hz, 6,000 RPM. - Electronic positioning for stepless horizontal adjustment. Double milling unit with 2 motors, each 4.5 kW, 150 Hz, 9,000 RPM. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Gluing unit for hot melt adhesive - With single roll/edgebanding magazine for roll material up to 3 mm and edgebanding up to 12 mm - 2-fold roll magazine for roll materials up to 3 mm (can be attached to the single roll magazine) - Horizontal roll holder End trimming unit - Mounted on the upper pressure beam, with 2 motors, each 660 W, 200 Hz - Pneumatic swivel 0 + 25 for straight and miter cuts. - Automatic adjustment for miter cuts with two different edge thicknesses (e.g. 0.4 and 1.2 mm) and for "edge overhang" for copying with edge thickness 1.0 - 3.0 mm. Automatic adjustment to the feed speed 20+30 m/min. Flush trimming unit 08.0555 - With 2 motors 1,850 W, 200 Hz, 12,000 RPM. Multi-function unit 08.353 - NC controlled with 2 motors, with automatic tooling for 4 profiles. Multi-profile edge trimming unit - with automatic tooling for 4 profiles via fixed-point control Spray nozzles, top and bottom - for applying cleaning agents Flat edge trimming unit Buffing unit - With 2 motors, each 180 W, 50 Hz, 1400 RPM. 1 Grooving unit - With 4.5 kW motor, 150 Hz, 9,000 RPM. - Horizontal and vertical adjustment manually with mechanical digital display - Pneumatic activation control - Manual swivel 90 ICOS open - PC-based control system with integrated PLC and electronic path control. - User-friendly interface with Windows standards - Simple, component-oriented

Condition: used, Year of construction: 2010, - Application of release agent, top/bottom - Joint milling unit - Gluing unit - Trimming unit - Copy milling unit SKF-L - Profile trimming blade unit - Spray cleaning agent - Self-adjusting trimming blade unit - Buffing unit Single-sided edge banding machine Manufacturer: IMA Type: Advantage 310 Year of construction: 2010 Technical data Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65* / 150 mm *at a max. workpiece thickness of 25 mm - Workpiece thickness: min. 8 mm, 12 mm with profile trimming blades max. 40 mm (with MFA 08.346), 60 mm (with SKF) - Smallest workpiece: 65 x 300 / 150 x 150 x 19 mm - Machining allowance per workpiece edge: 0 - 5 mm (observe max. chip cross-section) - Workpiece shape: right-angled - Material: chipboard, MDF - Surface material: direct coating (melamine resin paper), paper, film, veneer Edge material - Roll material without film: Paper edges & plastic edges: 0.3 - 3.0 mm Veneer edges: 0.5 - 3.0 mm - max. edge cross-section: 150 - 180 mm² - Cut edge strips: Strips: 3.0 - 8.0 mm - max. strip cross-section: 520 mm² - Edge height: min. 12 mm, max. 65 mm - max. upper edge overhang: 2 mm - Edge profiles Paper edge: approx. 0.4 mm, chamfer 15 Plastic edge up to 3.0 mm, radius depending on the tool Strip up to 8 mm flush milling (with interchangeable motor on MFA) Machine - Constant workpiece projection from the chain track: 35 mm + edge thickness - max. trimming cross-section 520 mm² - Throughput width: min. 65 mm (with projection of 35 mm) - min. workpiece length in feed direction: 150 mm - Overall height (top edge of chain track): 940 mm - Unit side: on the left in feed direction - Pneumatic connection: approx. 7 - 8 bar Kdjdpfxozuyp Es Afkjr Application of release agent, top/bottom Joint milling unit 08.379 and blowing nozzle - with 2 motors, each 4 kW, 9000 RPM, 150 Hz Gluing unit 283.1513 with oil bath gearbox - Adhesive output 0.8 l, 60 mm high, with quick-lock system - can be used for hot melt adhesive or PU adhesive - with single roll / strip magazine, roll diameter 800 mm - with 3 main pressure rollers and 3 counter pressure rollers Trimming unit 08.415 - pneumatically swiveling to 0 or 8 degrees - with 2 motors 660 kW, 400 V, 200 Hz, 12000 RPM - 2 HM trimming saw blades 160 x 3.5 x 22, Z=36 Copy milling unit SKF-L - with 2 motors 180 W, 400 V, 200 Hz, 12000 RPM - and 2 motors 400 W, 400 V, 200 Hz, 12000 RPM - 1 set of DP profile milling cutter I 80x12xHSK25-R, Z = 4, with HSK25 shank - Profile length in the feed direction: max. approx. 50 mm - Workpiece thickness: max. 60 mm - Working speed: max. approx. 20 m/min - Distance between 2 workpieces: min. approx. 400 mm - min. workpiece projection = 35 mm + profile depth Profile trimming blade unit 08.519 - For finishing a top and bottom milled quarter-circle profile Spray cleaning agent Self-adjusting trimming blade unit 08.521 - for removing hot melt adhesive residue from the edge area of the top and bottom of the workpiece Buffing unit 08.617-2 - with an upper and lower motor: 180 W, 50 Hz, 1400 RPM - 2 polishing pads 50 x 160 x 19 mm

Condition: used, Year of construction: 1996, - Double-sided IMA COMBIMA for longitudinal machining - Swiveling device - Double-sided IMA COMBIMA for transverse machining 1 used edge processing line IMA COMBIMA / K/ II/ R75 / 1075 / V / R3 Year of manufacture: 1996 Consisting of: - Double-sided IMA COMBIMA for longitudinal machining: Double edging unit 2 x milling units Gluing unit with granular pre-melting device 6-position roller magazine for edge material 1 x main pressure roller and 4 x follow-up pressure rollers Cutting unit Flush trimming 2 x fine milling units Profile trimming blade Surface trimming blade Buffing unit Smoothing unit - Swiveling device from longitudinal to transverse - Double-sided IMA COMBIMA for transverse machining Protective milling Double edging Grooving milling unit Gluing unit with granular pre-melting device Kedpfozuypxsx Afkedr 6-position roller magazine for edge material 1 x main pressure roller and 4 x follow-up pressure rollers Capping at the top pressure (retrofit to current model) Flush trimming Fine milling 2 x MFA milling units Grooving milling unit Profile trimming blade Surface trimming blade Copy buffing (4 motors) Buffing (2 motors) Smoothing unit Note: The technical data and descriptions are a transcript of the order confirmation at the time. Data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm Single-sided edge banding machine Manufacturer: IMA Type: Novimat Contour/I/G80/790/L20 Year of manufacture: 2009 Technical data - Electronically controlled feed speed: 6-30 m/min - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm - Maximum edge overhang from above: up to 8 mm edge thickness - 5 mm, over 8 mm - 2 mm Workpiece size: - Minimum workpiece length in the feed direction: 150 mm Kodpjzuyprefx Afkedr - Minimum workpiece width: 25 mm, thickness: 65 mm - Minimum workpiece thickness: 8 mm (without profile trimming blades) or 12 mm with profile trimming blades - Maximum workpiece thickness: without corner copying, max. 60 mm (max. 40 mm with corner copying) - Smallest element: 150 mm x 150 mm or 65 mm x 300 mm Note: *65 mm with a maximum piece thickness of 25 mm The edge banding machine is equipped with: - Hand-adjustable guide rail for inserting workpieces - Trimming units 08.376, 2 motors, each with 4.5 kW, spindle speed 9000 rpm, 150 Hz - Heating unit for warming the workpieces - Gluing unit with drive 283.1513, featuring a tightly sealed oil pan, drive arranged with glue pot content of 0.8 l and glue application height of 60 mm, with a pneumatic quick-clamping system for hot melt and PU adhesives, magazine for edge banding rollers and strips, edge banding roller diameter 800 mm - Glue pellet preheating unit with automatic feeding of glue pellets from a 30 kg container. - Automatic preheating unit for PU cartridges with a weight of approx. 2.5 kg and a capacity of 8-10 kg/h - Trimming unit 08.42/30/B, pneumatic adjustment of the saw blades from 0 - 25°, 2 motors 660 W, 200 Hz with frequency inverter and braking function - Pre-milling unit 08.055, swiveling up to max. 30° - Multi-chamfering unit 08.342, 2 motors, 660 W, 400 V, 200 Hz, 12000 1/min - Cleaning agent dispenser - Profile trimming blades 08.519 - Surface trimming blade 08.521 for removing excess glue from glue joints - Buffing unit 08.617-2, 2 motors with 180 kW, 50 Hz, 1400 rpm - Groove/milling unit with one motor Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2005, - Automatic infeed table - KFA unit - Return system Used single-sided edge banding machine Manufacturer: IMA Type: Combima Systems / I/R751220/R3 1 single-sided combination machine for trimming, edge gluing and edge finishing of panel-shaped workpieces made of wood and/or wood-based materials. Ksdpfx Afozuypleksdr - Automatic infeed table - KFA unit - Return system Technical data "Workpiece": Workpiece length - min.: 238 mm - max.: 2350 mm Workpiece width - min.: 142 mm - max.: 800 mm Workpiece thickness: - min.: 8 - 40 mm Technical data "Strip" (only for longitudinal processing): Roll material: - Paper edge bands & plastic edge bands: 0.3 - 3.0 mm - Veneer edge bands: 0.5 - 3.0 mm Edge height: - min.: 14 mm - max.: 45 mm Technical data "Machine": Variable workpiece overhang from the chain conveyor (including edge with edge thickness 0.3-3 mm): - min.: 40 mm - max.: 80 mm - PC control ICOS open - Feed speed v=5-25 m/min, frequency-controlled drive - Inclined roller table as infeed section NC infeed system for front and carcass parts - for length and width-independent automatic workpiece feed in single-sided edge processing machines. Only for the production of strip material in the 2nd pass - An additional stop rail, adjustable via NC axis. Double milling unit 08.376: - Controllable - Motor 1 operating in the same direction and motor 2 operating in the opposite direction - Reserve space on the unit carrier for a double trimming unit with electrical pre-installation for 2 x 6.6 kW. - Heater 300 lg, 2x1.5 kW, for preheating the workpiece edge. - Gluing unit 04.1570 system for straight edges and adhesive application to the workpiece. The edge thickness depends on the magazine used and is max. 3 mm. - Adhesive application for workpiece thickness max. 50 mm - 2 pre-melting tanks for PU adhesive - 12-position edge magazine for roll material 0.3-3 mm thick. (8 slots up to 3 mm, 4 slots up to 1.3 mm) Vertical roll holder for 12 rolls: - max. roll diameter 850 mm - max. edge height 45 mm - Trimming unit 08.42, for 2 motors mounted on the upper pressure bar - Pre-milling and milling unit with height sensor - with 1 motor 1000 W - Multi-profile / chamfer unit, with 2 motors 1000 W - Contour milling unit KFA 30 - Multi-profile drawing blade unit - Flat drawing blade 08.517 - Copy edging unit 08.604 - Edging unit 08.617-2 - Double milling stand 75.184, 1050 mm high, both stand sides can be used - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 6000 rpm - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 600 rpm - Motor spindle for the use of the Hydro-Format tool system - Return system, manufacturer Meinert Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2003, Single-sided edge trimming and gluing machine Manufacturer: IMA Type: AVM/K/I/G80/822/S3R3L20 Year of manufacture: 2003 For milling, edge gluing, and finishing for a standard groove - only for pre-shaped/pre-grooved doors and square-edged doors Left-hand machine (fixed stop on the left). Complete processing in 3 passes 1st pass: Processing of the top surface of the door (transverse processing) 2nd pass: Door long edge 3rd pass: Door long edge During the 2nd and 3rd passes, the protruding transverse edge from the 1st pass is milled off by using a co-rotating/counter-rotating milling process. Double groove gluing is only possible through modifications to the machine and subsequent manual finishing of the edge. Max. door thickness: - Straight edge: approx. 70 mm - Groove gluing: approx. 60 mm Stable machine frame as a support for aggregates and housing for electrical installation. Drive for feed speeds of approx. 5-25 m/min., mechanically infinitely adjustable. (not to be confused with processing speed) Continuous, plastic-coated strip-type conveyor chain, approx. 80 mm wide, with automatic central lubrication. Manually height-adjustable top pressure with a V-belt 80 mm wide and spring-loaded, ball-bearing guide rollers. Machine length approx. 10,900 mm Infeed table at the machine inlet. 1 horizontal, manually adjustable, unheated stop bar 1 joiner milling unit controllable, not swiveling, without sensing Kdedpfjzuykvjx Afkjr with 2 motors, each 3 kW Gluing unit for optional operation of straight edge or softforming gluing, by changing the glue application. Edge material: - Strips: up to 1.3 mm - Roll material: 0.4-3 mm - Solid wood strips: 6 mm Strip length max.: 2550 mm Strip height: 14-80 mm (depending on glue application) with: - Side adjustment by hand for the pneumatically controlled glue application. - Height adjustment by hand -15mm downwards and up to +10mm upwards. 1 bell for the main pressure roller, manually adjustable 1 glue application 0.8L, max. edge height 70mm, straight edge with pneumatic quick-release, Chem-Coat coated, electronic temperature control 1 hot melt glue application 0.8L with quick-release, up to max. 80 mm high edge material, soft edge, Chem-Coat coated, with temperature control and control unit for the strip coating 1 automatic Quickmelt hot melt glue feeder with a heating power of 5.0 kW 1 2-fold magazine only for edge material up to 3.0 mm thick, can be manually attached to the single-roll magazine 1 groove forming pressing unit for pressing the edge material into the groove with: - an activation unit 15 kW for re-activating the edge material for groove forming - a pneumatically controlled forming shoe for the underlapping edge - a pneumatically controlled forming shoe for the entire groove - additional post-pressing rollers for the edge areas in the groove - an electro-pneumatic lateral retraction device for the entire pressing unit 1 horizontal adjustment with mechanical digital display 1 trimming unit for 2 motors mounted on the top pressure for trimming the front and rear edge/strip overhang, for trimming cuts flush or with a bevel. 1 milling unit for 2 motors with height sensing, side sensing, for pre-milling from below and above with 2 motors 1kW, 400V, 200Hz, 12,000 RPM, 30° swiveling 1 milling unit for 2 motors with height sensing, side sensing, for fine milling from below and above with 2 motors 660W, 400V, 200Hz, 12,000 RPM, 30° swiveling Note: The technical data and descriptions are copies of the original order

Condition: used, Year of construction: 2009, Edge banding machine Manufacturer: IMA Type: Novimat/I/G80/650/R3 Year of manufacture: 2009 Technical data - Workpiece overhang from the chain conveyor: 38 mm - Feed width: min. 65 mm (with max. workpiece thickness of 25 mm) - Workpiece length in feed direction: 150 mm - Overall height (top edge of chain conveyor): 960 mm - Feed speed: approx. 6 - 30 m/min, electrically adjustable - Machine control system ICOS open compact Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65 mm - Workpiece thickness: 8 - 40 mm (with edge trimming function) / 60 mm (without edge trimming function) Kdsdpfx Aozuyi Ejfkjr - Smallest workpiece: 150 x 150 mm or 65 x 300 mm - Edge material: paper, plastic and veneer - Height: 14 - 65 mm - Roller material thickness: 0.3 - 3.0 mm (veneer edges limited to max. 1.0 mm) - Max. upper edge overhang: 5 mm Units Infeed area - Release agent applicator mounted at the top and bottom, not adjustable Edge trimming - 2 motors 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function - Motor 1 counter-rotating - Motor 2 co-rotating Gluing unit VTG 3-6 - with one preheating nozzle 300 mm for preheating the workpiece edge - 6-position edge magazine for roller material 0.3 - 3 mm thick. - 1 driven main pressure roller and 4 pressure rollers, with scraper, pneumatically adjustable Glue application - with pneumatic quick-lock system - Chem-Coat coating - electronic temperature control - Volume 0.8 l Pre-melting tank approx. 1 l - Heating power 3 x 400 W - with EVA glue, approx. 7.0 kg/h - with filler-free glue, approx. 5.0 kg/h Cutting unit - 2 motors 660 W, 200 Hz - incl. frequency inverter with braking function - pneumatic pivoting 0+25 for straight and bevel cutting Flush trimming - 2 motors each 1000 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function Multi-profile trimming unit - 2 motors each 660 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function - for trimming 4 profiles - with stepper motor axes for horizontal and vertical positioning Contour trimming unit KFA x30 - 1 motor 500 W, 400 V, 400 Hz, 18000 rpm - Program-controlled conversion for up to 4 profiles - incl. fine positioning for different edge thicknesses Multi-profile scraping blade - Stepper motor axes for horizontal and vertical positioning - Scanning from above and below (max. 4 profiles) - Scanning from the side via pneumatic pressure Spray nozzles at the top and bottom for applying cleaning agents - fixed, not adjustable Surface scraping blade - with height sensing skid - electronically controlled horizontal positioning Buffing unit - 2 lower and 2 upper motors, 180 W, 50 Hz, 1400 rpm - 1st motor pair with cloth-sisal discs 50x160x19 mm - 2nd motor pair with polishing discs 50x160x19 mm - The motors operate in the same direction and are both tilted and pivoted in the feed direction. - Each motor can be individually adjusted vertically 2x NC-controlled grooving - 2 milling motors each 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function - one manual 90-degree pivoting device from 180 -270 with co- and counter-rotating function - Horizontal, stepless adjustment with AC servo motor for grooving unit Workpiece return Note: The technical data and descriptions are copies of the order confirmation at the time. The information is for informational purposes only and is non-binding.