Mesh welder

Schlatter MG320

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA Bdedpewu Tu Djfx Aduek No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: refurbished (used), functionality: fully functional, working width: 1,200 mm, Schlatter MG900, 1,200mm wide, with 4 x 100kVA transformers, updated control with Siemens S7-300 PLC from 2016. Mechanically completely rebuilt and all new control cables. Bdjdpfx Adovvf T Aouok

Condition: excellent (used), Year of construction: 2009, Technical Details : Year - 2009 Beam welding machine outlet height: 1400mm (UK beam from ground) Min. strap length: 0.8 m Max. beam length: 16.0 m Base width during production: 58 mm (inside diagonals) Finished beam width: 70 – 116 mm (external dimensions of bottom chords) Lattice girder production speed: max. 15 m/min Design of the wire feed speed: 18 m/min (upper and lower belt) 38 m/min (diagonals) Carrier types that can be produced: KT KTS Top belt Ø: 5 – 16 mm 5 – 7 mm Lower belt Ø: 5 – 16 mm 5 – 7 mm Diagonal Ø: 4.5 – 9 mm 5 – 7 mm Height: 70-400mm 80-310mm Division of the diagonal: 190 – 210 mm 200 mm Bodorn N Efopfx Aduedk Primary material: Cold or hot rolled reinforcing steel from coil in accordance with EN 10080:2005 in weldable quality, max. carbon content 0.20 % The line is in excellent working condition !

Year of construction: 2013, condition: excellent (used), Comes for sale: 1 piece used H crane traverse Manufacturer: SMV Scheunemann type: 13-0163 SHTS60 BJ: 2013 Own weight: 4.105Kg Bdjdpfx Adjit T N Aeusk Combined 60t and 28t load lifting points dimensions L x W x H: 5.900 x 2.700 x 1.200mm Can be inspected in our warehouse in 09599 Freiberg.

Condition: excellent (used), Year of construction: 1992, Manufacturer EVG Type TSD 7-25 Machine No. 958 Year of manufacture 1993 Working direction L > R Beam types KT 8… Beam height (mm) 90-250 Carrier length min. (mm) max. (mm) 14,000 Fixed lengths: Yes Cutting pitch (mm) 100/200 Spool unwinder (pcs.) 5 LAR: Yes Wire diameter - 5-12 mm smooth/ribbed Bodpjwp Ilyjfx Adujdk Diagonal - 4-7 mm smooth / ribbed Stack height max. (mm) - 500

Year of construction: 2001, condition: ready for operation (used), A steel mesh welding system for the automatic production of welded steel wire mesh is available. Mesh width range with a bar diameter of 3mm to 6mm: 500mm-2150mm, mesh width range with a bar diameter of 2mm to 3mm: 500mm-2000mm. Grid length range with a rod diameter of 3mm to 6mm: 600mm-3000mm, grid length range with a rod diameter of 2mm to 3mm: 600mm-2000mm. Min. cross wire pitch: 12.5mm, min. longitudinal wire pitch: 25mm, wire diameter range: 2mm-6mm, max. number of longitudinal wires: 52, production capacity: 52 strokes/min, rated power at 50%: 840kVA, max. stack height: 600mm. Total system dimensions X/Y/Z: approx. 20000mm/7600mm/3400mm. Including longitudinal wire distributor in 40mm and 50mm pitch and longitudinal wire console in 40mm, 50mm and 75mm pitch. Documentation available. On-site inspection is possible. Bdsdpfxewfg Eqj Aduek

Condition: used, 18 pieces Pallet lift Schwingshandl S-MDEPAL-01 Used goods Year of manufacture 2019, very good condition, see pictures System was only in trial operation in a food company for approx. 1.5 years! Length: 205 cm Width: 154 cm Height: 615 cm Roll width: approx. 85 cm Roller diameter: approx. 9 cm Table size: approx. 130/108 cm Payload: approx. 1000 kg 18 pieces available. Negotiated price: from € 2.000,- net ex location Depending on purchase quantity and design Dismantling takes place from April to June 2024. Location Northern Italy. Viewing possible by appointment. Further information on request. Partial sale possible. Systems will be professionally dismantled and loaded. Transportation and customs clearance can be carried out by us. Installation and programming can be carried out by partner companies. EVERYTHING MUST go! - from location until max. end of June 2024!!! The following products of the plant are also for sale: 300 x Dematic Multishuttle DMS 2 - 31.5 kg 350 m Dematic Sorter Flex Sort Crossbelt SC3 XB 3900 m container conveyor technology 600 m pallet conveyor technology 34 x Dematic Vertical Lift 11 m height - 4 m/s 3 x pallet stackers 4 x Schwingshandl palletizing systems 2 x pallet stations Autopall Schwingshandl 20 x pallet stations Manpall Schwingshandl 18 x pallet lifts 4 x Dematic pallet stations 14 x pallet wrappers Unitech UNI WRAP 200A + 900 A 25 x Schwingshandl 35 kg container stacking system 8 x labelers 20 x weighing stations 200 x system control cabinets Partial sale possible! Bjder Iitlepfx Adujdk (Subject to changes and errors in technical data, specifications and prices as well as prior sale! See our GTC, all prices excl. VAT ex stock).

Condition: used, Year of construction: 2002, functionality: fully functional, SCHLATTER model MG 316 Mesh welding line Technical Details - • Purpose: For the production of standard mesh • Manufacturer Schlatter • Condition: Not in operation • Longitudinal wire Ø min: 3 mm • Longitudinal wire Ø max: 8.5 mm • Crosswire Ø min: 3 mm • Crosswire Ø max: 8.5 mm • Cycles (transverse wires) max: approx. 120 Bodpfx Aov Unt Nsduodk • Max mat width: 2500 mm • Max nr. of longitudinal wires: 26 • Longitudinal wire feed: From coil • Crosswire feed: From coil • Longitudinal wire spacing: 100/150/200 mm • Crosswire spacing: 100-400 mm • Year installed: 2002 • Weight: ca. 30’000 Kg

Condition: refurbished (used), Year of construction: 2025, JAGER welded mesh line U-Gsa-st Full revamped "as new" Technical data 24 pay off for longitudinal wire spools, longitudinal wire straightening equipment Line wire pull off system Longitudinal wire loop Longitudinal wire straightening equipment Cross wire magazine Number of installer line wires : 24 up to 10 mm Diameter of lines wires : 4 to 10mm Diameter of cross wires : 4 to 10mm Bdodpfjwu Dcxox Adusk Separation between line wires : 100, 150, 200, and 300 mm Separation between cross wires : min 30 mm , steplessly programmable Max. length of cross wire (mesh width) 2500 mm , max welding width : 2400 mm Mesh length : min 3000 mm and max . 6000 mm Trafos : 8 x 160 Kva Number of installer line wires: Number of installer line wires : 24 up to 10 mm Diameter of lines wires: 4 to 10mm Diameter of cross wires: 4 to 10mm Separation between line wires: 100, 150, 200, and 300 mm Separation between cross wires: min 30 mm , steplessly programmable Max. length of cross wire (mesh width): 2500 mm Max welding width: 2400 mm Mesh length: 3000 - 6000 mm Trafos: 8 x 160 Kva