Used Isal Pb70 Et for sale (101,533)

Condition: used, Year of construction: 1989, Stetter concrete mixing plant Type H1 -Scraper plant Colst Hr Tgsim Ttyegt -mixing portal complete with mixer 1 cbm, scales, bucket elevator -Control system -3 x cement silo 60 t 1 x cement silo 50 t -Heating system

Condition: used, Year of construction: 2016, operating hours: 1,613 h, mileage: 52,726 km, fuel type: diesel, Operating hours: 1613, first registered: June 23, 2016, self-propelled_____Standard equipment: Fan unit - fan drive hydraulically via the transmission-independent PTO on the chassis (semi-hydrostatic drive) - Hydraulic fan drive - 50 l hydraulic oil tank - Engine compartment lined with sound-insulating material - Fan exhaust air duct upwards through the hopper front section - Hydraulic pump, single sweepings hopper - Sweepings hopper (with tailgate and sieve) and water tank made of 1.4003 chrome steel - Engine compartment paneling made of mild steel - Sweepings hopper gross volume 6.5 m³ - Sweepings hopper floor made of chrome-alloyed stainless steel, 1.4301 - Sweepings hopper tilt angle approx. 55 degrees - Dirt chute made of 1.4003 chrome steel - Inspection hatch right and left - Dirty water drain 4", A-coupling - Air duct sieve, manually foldable - 2 rotating beacons at the rear of the KGB - Air shut-off on the suction hose, pneumatically operated - Multi-stage safety support, pneumatically operated - Marker lights at the rear of the container, side marker lights - Integrated water tank - Preparation for rear suction hose boom or mounted on the roof - Side marker lightsSweeping material pickup - Sweeping material pickup, wear-resistant coated - Rough pickup by tilting the suction mouth - Suction hose diameter 250 mm - Pushed disc brush - Hydraulically driven steel disc brush - Pulled steel disc brush, diameter 500 mm - Continuously variable speed control for disc brush - Two robust pivoting trailing wheels - Automatic lifting of the sweeping units when reversing - Work lights for sweeping unit Roller brush - Pulled roller brush suspension - Brush length 1,300 mm, brush diameter 406 mm with plastic trim (depending on the chassis) - Hydraulically driven roller brush - Throw limiter apron for Roller brush unit water system - Water tank capacity approx. 1,554 l - Water tank made of chrome steel, 1.4003 with coating - Water level indicator in the driver's cab - Water filling device, Storz C (2"), right - Manual water filling device, right and left - Water pump, hydraulically driven - Automatic water stop when the sweeping units are raised - Spray water connection, 3/4", rear right - Water blow-out system - Electric water valves in the driver's cab - 2-nozzle low-pressure front instrument panel and control panel - Bucher instrument panel, including 7" color display - Ergonomic control unit, mounted on the driver's door, equipped with the main functions - Display includes the following functions: water level indicator, operating hours, and rear axle load - Warning and indicator lights for rear axle load - Control and monitoring unit for regulating the brush contact pressure (broom relief), stepless speed control of the disc brushes - Electric valves for the water system, operated in the driver's cab. - Operation The dirt container functions can be controlled via a cable remote control from the driver's cab, but also from outside. - Operation of the air guide sieve, operation at the rear right of the vehicle - Overload indicator for rear axle load, warning lamp in the display (option Colim Ttsfy Am Ueyjgt

Year of construction: 1946, Condition: used, Vats - Installation of 4 concrete vats (building) including: - Agitators - Pumps - Valves - Piping - Installation of 1 concrete vat with: - Agitator - Pumps - WACO filter - Piping ----- Purification - 5 purifiers + KADANT BLACK CLAWSON Fibernet - Tank - Sand removal screw - Conical stainless steel pulp chest - LAMORT purifier (partially dismantled, as is) ----- Supply - ALLIBE stainless steel vat - Pumps - Regulator - Control system ----- Starch water pumps - 2 MORET motor pump units - Stainless steel tank - Equipment for concrete vat (building) - Pumps - Piping ----- Paper Machine No.2 Brand: NEYRET-CORDEBART-THIRY – Year: 1946 Width: 2450 mm Hood and steam installation: BELLMER 1) Wet section - Natural drying: - 6 stainless steel suction boxes for paper dewatering - Mechanical drying: - 7 suction boxes with ceramic and plastic linings - Suction cylinder 2) Press section - Press No.1 with 2 cylinders (pneumatic tightening, LAMORT doctor blade) - Press No.2 with 2 cylinders (pneumatic tightening, LAMORT doctor blade) - Press No.3 with 2 cylinders (pneumatic tightening, LAMORT doctor blade) - Press No.4 "OFFSET Press" with 2 cylinders (hydraulic tightening) 3) Dryer section Installed in a large BELLMER suction cabin with automatic doors – humidity control system - Pre-dryer section: - 24 drying drums - 5 felt dryers - 23 doctor blades - Size press: - 2 cylinders - Pneumatic tightening - Reducer - 2 doctor blades - Post-dryer section: - 14 drying drums - Drying system: LANG (steam-based) 4) End of line - Rewinder with multiple cylinders - Sheet cutter: IBS RCS 5000 - Pneumatic equipment ----- MAP 2 Control Room - Digital control desks - Electronic installation - Paper monitoring scanner - Small furniture: coffee machine, top refrigerator, hot oven THERMOS SR1000 - Insect destroyer - Workbenches, vise, small rack ----- MAP 2 Sauce Kitchen - Remote-controlled sauce distribution network - Stainless steel storage - Agitator - Pumps - Valves - Filters ----- Sauce Preparation Kitchen (similar to MAP 1 and MAP 2) - 100T starch silo (old) with: - Valves - Dispenser - 2 pumps - Milk preparation tank - 2 dosing units for retention products (old) - Suspended milk cooker with digital control including: - Agitator - Pump - Double-jacket delumper - Steam extraction system - Tanks, pumps, mixers - Piping - Colorant installation ----- Cgeliewbg Svem Ttyet Vacuum Production Installation - 8 ALLIMAND vacuum pumps ----- Sauce Distribution Network

Condition: excellent (used), Year of construction: 2013, machine/vehicle number: MING, frame width: 1,100 mm, load capacity per stand: 9,000 kg, 1 linear meter of pallet racking, heavy-duty racking, high-bay storage racking Height 2.75 m, depth 1.1 m Load capacity per pair: 3000 kg, bay load 9000 kg Incl. wooden shelves A total of approximately 300 linear meters are available! Cgslim Ttjwb Ulwjyot Please inquire about your desired length. Shelf is empty, disassembled, and packed on a pallet. Very good condition, see pictures. Pickup only by appointment in 75053 Gondelsheim. A forklift is available for loading. Shipping via freight forwarder is possible; please inquire with your postal code.

Condition: used, Functionality: fully functional, HYDRAULIC HOT PRESS P65 Manufacturer: STEMA Model: P 65 Code: PRS-038 USED MACHINE – V380/50 Plan size: 3000×1300 mm Plan heating with hot water 6 pistons Prepared for connection to the centralized system Cgjliowdgnpjm Ttyst

Condition: excellent (used), Year of construction: 2002, Capacity: 1200x1000x600 mm WORKING CAPACITY Longitudinal (x): 1200 mm Vertical (z): 600 mm Cross (y): 1000 mm CNC Cgjlimewcyugo Ttyet Cnc: SIEMENS 840D SPINDLE Spindle power: 20 Kw Rotating speed: 24000 Rpm Torque: 38 Nm FEEDS Rapid x: 60 m/min Rapid y: 60 m/min Rapid z: 40 m/min TABLE Floorspace (lxwxh): 1500x1000 mm ATC Positions: 30 Total power supply: 85 Kw Machine total weight: 18000 Kg

Condition: used, _____ Description: Year of manuf. : 2017 Control : Turbo Form In general: Cslimjv Swpzs Ttyogt Technology:Form and surfaceroughness Tester Control:Turbo Form Year of manufacture:2017 Measuringdiameter (max.):450 mm Measuringheight (max.):550 mm Workpiecemeasuringweight (max.):60 kg Tablediameter:330 mm Equipment/Accessory: Turningtable:Engine driven, air-guided Turn-/Swivelmodul:CNC-driven Touchprobe:FT3 Analysisunit:Moveable in Height and sideway Further Accessory:Reference units for Round and Roughness

Condition: good (used), machine/vehicle number: 3382, Year of construction: 2006, lifting height: 4,040 mm, mast type: duplex, fork carriage width: 200 mm, fork length: 2,500 mm, total length: 5,250 mm, total width: 2,600 mm, operation weight: 21,300 kg, engine type: Diesel, lifting capacity: 13,600 kg, additional equipment features: Front mud guards, Rear mud guards, Weight system, Centralized greasing system, Equipment: lighting, SveTruck 136120-35 from Uniktruck Cgslim Ttjvc Hg Dsyjt

Condition: good (used), Manufacturer: SOMET Tip: SDJ 300 Measurable tool diameter: 6 - 300 mm Celim Ttsd N S Ubsyjgt Measurable tool length: 40 - 500 mm Accuracy: 0.002 mm 1x Swap socket ISO 40 1x Swap socket ISO 45 1x Swap socket ISO 50 1x Test mandrel ISO 50 used! Dimensions: 1250 x 600 x 1870 mm

Condition: excellent (used), Year of construction: 2016, Functionality: fully functional, measuring range X-axis: 275 mm, measuring range Y-axis: 250 mm, workpiece length (max.): 4,000 mm, No reserve price - guaranteed sale at the highest bid! TECHNICAL DETAILS Scan Performance Measurement Rate: 480,000 measurements/s Scan Area: 275 x 250 mm Resolution: 0.050 mm Accuracy: up to 0.030 mm Volumetric Accuracy: 0.020 mm + 0.060 mm/m Part Size Range: Recommended: 0.1 – 4 m Cslimjwbuxwo Ttyogt Laser and Light Source Light Source: 7 laser crosshairs (+1 additional line) Laser Class: II (safe for the eye) Data Formats Output Formats: .dae, .fbx, .ma, .obj, .ply, .stl, .txt, .wrl, .x3d, .x3dz, .zpr Software 3D Software Platform: VXelements Reverse Engineering Software: VXmodel Software (1-Year License) EQUIPMENT - Laptop - 4 m connection cable - 8 m connection cable - Power supply - Original carrying case - the workstation is not included! - 15 sets of positioning targets - Calibration plate - User manual The VXmodel software is a post-processing software integrated into Creaform's VXelements 3D software platform. It enables the seamless transition of 3D scan data to CAD software or 3D printing software. The software allows for the simple and fast processing of 3D scans for additive manufacturing.

Condition: good (used), Functionality: fully functional, Item: AV-12266-AV12270-Vertical21800L Stainless steel Vertical Insulated Jacketed tank, Capacity 21,800 L Cgeliev I Hbxjm Ttyjt Exterior dimensions: Dia Ø 2500/2600 mm Total H 6500 mm. Vertical isolated, stainless steel tanks with cooling jacket - 5 pcs. Manhole bottom. AISI 316

Condition: used, Year of construction: 2022, operating hours: 762 h, power: 62 kW (84.30 HP), Operating hours: 762, First registered: September 28, 2023_____Equipment: Bucher-Johnston CX 202 Euro 6 CVM engine, Euro 6 certified with integrated diesel particulate filter, SCR catalyst and AdBlue as standard, 2 side brushes, front steering (2-wheel steering), Special equipment: Right-hand drive RAL9016 white, Coarse dirt/leaf flap, Shut-off valve - for return water from the sweepings hopper, CFC-free air conditioning, Large brush mirror to improve visibility into the sweeping area, Digital tachograph, Heated exterior mirrors, DAB+ radio with CD (Alpine, type CDE-205DAB), MP3, front aux, USB, Bluetooth, microphone, Deluxe driver's seat with headrest including seat heating, 50 km/h, LED rotating beacon at the front behind the cabin, Manual water valves for the Broom arms, storage location: 54595 Prüm Celim Tsuqtfljtyegt

Condition: good (used), overall weight: 400 kg, Skinetta ASK 450 Strapping machine Purpose of the machine The stretch banding machines in the SKINETTA series are used to tightly band (wrap) individual products or several individual products with polyethylene film. (wrapping) with polyethylene film. In contrast to shrinking machines, the wrapping film is pulled tightly around the pack before sealing. This tightening is the main advantage of the process. The result is up to 20% less film consumption. A particular advantage of the patented SKINETTA tightening system is the infinitely variable, fine dosage. The sealing (welding) of the film takes place in a very small space and the result is a clean seal seam with very small protrusions. By adding a SKINETTAther or SKINETTAshrink heating hood and using an appropriately wide film, the excess film protruding beyond the container can be shrunk to the side. This process makes the pack even more stable and prevents individual products from falling out of the sides of a grouped pack. Full closure of the packs by sealing, sealing and side folding is possible with appropriate additional equipment. The range of SKINETTA stretch-banding machines comprises 6 basic types for film widths to be processed from 25 mm to 200, 290, 440, 590, 790 and 1250 mm width. In addition to the single-track version, two to four-track systems are manufactured to increase output. - In the SK series (semi-automatic), the products are grouped on the machine table by one operator. The insertion into the film and the subsequent stretch-banding process is triggered either by a foot switch or a two-hand control, subsequent full automation is possible (except for type SK 200), - In the ASK series (fully automatic), the products are fed, grouped and then banded fully automatically using appropriate additional equipment. A modular system of feeding, grouping, forming and special equipment based on over 20 years of experience allows adaptation to the most diverse customer tasks with tried and tested standard elements. Technical data Celijp U T Ifjm Ttyogt Machine dimensions (basic machine) Length: 1670 mm Width: 980 mm Height: 1700 mm Table height: 1700 mm Weight: 400 kg Power connection: 400 Power requirement: 6.1 kW Additional equipment: bar chain conveyor You can find more items - new and used - in our store! International shipping costs on request!

Condition: new, Year of construction: 2024, Functionality: fully functional, saw band length: 3,370 mm, saw band width: 27 mm, warranty duration: 12 months, net weight: 890 kg, CUBO 350 NC FLAT is a numerically controlled automatic hydraulic cutting machine for cutting medium-sized pipes, profiles, T-bars and bars. The machine allows for angle cutting. The integrated feed vice with encoder ensures precise cutting lengths. Thanks to the Industry 4.0 Ready system, the CUBO 350 NC FLAT can be controlled and programmed remotely or via touch screen. The CUBO 350 NC BOX model is a front band saw that ensures user safety by securing all 4 sides with a special sheet metal covering all moving parts of the band saw. The safety system ensures full accessibility for maintenance. An innovative and easy-to-use 7-inch touch screen with an intuitive interface allows control over all machine settings. 99 cutting programs and 10 different cutting lengths can be programmed on the same bar. The CNC control gives access to all the machine's operating functions: automatic calculation of the blade thickness, the number of stroke repetitions and pieces to be cut, the blade speed and the lowering feed, the cutting length for each bar. The interface also allows viewing the status of the CUBO during operation and anomalies with self-diagnosis. Integrated feeder allowing automatic repetition of the cutting process. The feeder slides on a hardened and chromed bar; high positioning precision thanks to the incremental power supply of the ball screw with circulation by means of a self-locking electric motor with inverter, mounted on a floating plate to facilitate the loading of non-straight bars. The saw frame has a rigid cast iron structure manufactured by IMET with a tubular section, which ensures high resistance to deformation and better projections in each section and material. The arc is equipped with a cemented and hardened endless screw and a crown made of high-quality resistance bronze alloy. The mechanical material detection device ensures the blade approaches the material quickly, automatically detecting the first cutting point, while the end of the cut is managed by a microswitch on the moving blade guide, which allows for perfect blade positioning thanks to the hard metal pads and additional bearings. IMET machines can be connected to the company network and used remotely thanks to SAWFACTORY and a modem. SAWFACTORY is a dedicated software that allows you to manage the cutting process from your desk by setting cutting programs and monitoring the workflow thanks to a dedicated web application. The software also allows you to use the help of our technicians remotely. Technical data: Belt width: 27 mm Vise opening width: 350 mm Belt dimensions: 3370x27x0.9 mm Belt speed: 15-100 m/min Belt motor power: 1.8 kW Working height: 880 mm Cgjlimjwcfbxo Ttyot Final waste: 80 mm Single feed length: 515 mm Coolant tank capacity: 100 l Hydraulic tank capacity: 20 l Dimensions: 1850x1900x1990 mm Weight: 890 kg

Condition: good (used), Year of construction: 1999, Complete mixer Cgjlewaxzmoim Ttyjt

Condition: new, Year of construction: 2022, Functionality: fully functional, cooling capacity: 13.8 kW (18.76 HP), type of cooling: air, overall weight: 193 kg, total width: 400 mm, total length: 1,400 mm, total height: 1,400 mm, heating capacity: 16.2 kW (22.03 HP), Cooling capacity: 13.8 kW (12/7 — 35°C) Heating capacity: 16.2 kW (40/45 —7°C) Year of manufacture: 2022 Version: 250 V, 1 Phase, 50 Hz Options: Heat pump, Hydralic module Colimsu Urkyo Ttyogt Hydraulic module: 1 pc. water pump, expansion vessel Heat exchanger: Plate Refrigerant circuit: 1 pc. Compressors: 1 pc. Mitsubishi (Rotary Inverter DC) Type of refrigerant: R-32 Number of fans: 2 pcs. Dimensions: 1.4 x 0.4 x 1.4 m Weight: 193 kg Working hours: 0 h. Condition: excellent, new

Condition: new, Year of construction: 2025, Smart Safety. Clean Air. Enhanced Efficiency. Take your workplace safety to the next level with the TFON Airwet Series—a cutting-edge wet-type air suction system specifically designed to eliminate sparks and dust generated during deburring processes. By drastically reducing the risk of fire and explosion, the Airwet Series protects both your workforce and your facility. ✅ Fire & Explosion Prevention Minimizes hazardous particles and ignition sources at the source. ✅ Improved Air Quality Removes airborne contaminants to ensure a cleaner, healthier workspace. Colisvg U Dxem Ttyegt ✅ Easy Integration Compact design fits effortlessly into your existing machinery and workflow. ✅ Boosts Operational Safety & Compliance Supports adherence to occupational health and safety standards.

Condition: good (used), Year of construction: 2006, Functionality: fully functional, 2 HYUNDAI ROTOPALETTE MACHINING CENTERS, type VX380, from 2006 and 2007 2 tables measuring 650 x 400 X 520 Y 360 Z 350 Cgelswbg Idjim Ttyet 12,000 rpm spindle - BT 30 14-position ATC turret HP spindle center coolant Chip conveyor

Condition: new, pressure: 63bending length: 2500column width: 1980motor: 11slide stroke - max.: 150opening width: 400CNC Press break KK Industries 63x2500 4 Axis Y1-Y2-Y-X-R mit CNC Bombing Technical Parameters:Pressing Force: 63 t Bending Length: 2500 mm Distance Between Columns: 1980 mm Throat Depth: 300 mm Slider Stroke: 150 mm Maximum Opening: 400 mm Slider Down Speed: 180 mm/s Slider Return Speed: 170 mm/s Slider Working Speed: 14 mm/s Main Motor Power: 11 kW CNC System: ZY68 Number of Control Axes: 4+1 Oil Tank Capacity: 150 L Celim Tov Trgqjtyjgt Back Gauge:X-Axis:X-Axis Travel: 600 mm X-Axis Speed: 200 mm/s Positioning Accuracy: ±0.10 mm Repeat Positioning Accuracy: ±0.015 mm Motor Power: 0.85 kW R-Axis:R-Axis Travel: 150 mm R-Axis Speed: 100 mm/s Positioning Accuracy: ±0.10 mm Repeat Positioning Accuracy: ±0.015 mm Dimensions and Weight:Length: 2750 mm Width: 1350 mm Height: 2320 mm Weight: 4000 kg Delem T53 Control System (additional cost 5,000¤)

Condition: new, Year of construction: 2024, Functionality: fully functional, saw blade diameter: 350 mm, rotational speed (max.): 3,600 rpm, Automatic IMET VELOX 350 AF-NC disc cutter for aluminum with a swiveling arm from 0° to 45 degrees left and right and a tilting head up to 45 degrees. Fast and precise angle lock at 0°, 15°, 30° and 45° right and left with an additional scale for setting non-standard angles. Description: Swiveling arm from 0 to 45 degrees left and right Tilting head up to 45 degrees Fast and precise angle lock at 0, 15, 30 and 45 degrees right and left and an angle scale for setting non-standard angles. Handle for locking the head at any angle Designed for cutting aluminum and light metal solid materials and profiles with high accuracy Control panel with the ability to program all machine operations (including the cutting start point and the cutting end point), showing the blade speed, cut counter, cycle time, motor current and possible errors Feeder with a vice with a max. jaw opening of 200 mm, with a max. stroke of 530 mm, with a min. 2.5 mm stroke Number of cuts (1-9999) and number of feeds (1-29) set from the control panel Cgslim Ttjwcd Ukoyst Manual setting of cutting length with digital readout Two front pneumatic vices with the possibility of transverse movement on the work table, vertical pneumatic vice Metal cutting blade guard Possibility of connecting a chip extractor Mist lubrication system operating only during cutting Instruction manual in Polish CE certificate, compliance with CEE and EMC standards Electrical elements compliant with the standards: EN60204-1, EN55011 and EN50082 Technical data: Diameter of the blade: 350 mm Opening width of the vices: 200 mm Speed of the blade: 3600 rpm Power of the blade motor: 2.2 kW Working height: 930 mm Final waste: 355 mm Single feed length: 520 mm Coolant tank capacity: 40 l Dimensions: 1800x1450x1950 mm Weight: 607 kg

Condition: new, Year of construction: 2022, Functionality: fully functional, cooling capacity: 12.9 kW (17.54 HP), type of cooling: air, overall weight: 178 kg, total width: 440 mm, total length: 1,450 mm, total height: 1,570 mm, heating capacity: 14.1 kW (19.17 HP), Cooling capacity: 12.9 kW / 3,7 tons (12/7 — 35°C) Heating capacity: 14.1 kW / 4 tons (40/45 — 7°C) Year of manufacture: 2022 Options: Heat pump, Hydralic module Hydraulic module: 1 pcs. water pump, expansion vessel Heat exchanger: Plate Refrigerant circuit: 1 pcs. Compressors: 1 pc. Mitsubishi (Rotary Inverter DC) Cgjliju Uripem Ttyet Type of refrigerant: R-32 Number of fans: 2 pcs. Version: 250 V, 1 Phase, 50 Hz Dimensions: 1,45x0,44x1,57 m Weight: 178 kg Working hours: 0 h. Condition: excellent, new

Condition: new, Year of construction: 2024, Functionality: fully functional, saw blade diameter: 350 mm, overall weight: 266 kg, IMET VELOX 350 semi-automatic circular saw for aluminum with a swiveling arm from 0° to 45 degrees left and right and a tilting head up to 45 degrees. Fast and precise angle locking at 0°, 15°, 30° and 45° right and left with an additional scale for setting non-standard angles. VELOX 350 SHE is a semi-automatic circular saw for cutting aluminum and light alloys. VELOX 350 SHE can cut from 45° left to 45° right and cuts at an angle of up to 45° to the vertical axis. The miter saw is the ideal tool for high-precision cutting and finishing of profiles and solid aluminum. The machine is equipped with an automatic stop system at 0°, 15°, 15°, 30° and 45° both to the right and left. All machine operating functions are controlled via the control panel. In particular, it allows you to set the head position in terms of reaching the material and starting and ending the cutting operation, allows you to view the machine's operating conditions before and during processing. It also has a self-diagnosis system for detecting errors. Two pneumatic vices located at the front and moving laterally on the work surface allow you to block the material. The blade of the disc is fully protected by a guide. There is also a conveyor for chip extraction and an adjustable rod stop. The VELOX 350 SHE has a nozzle for spray lubrication. Features of the device: The cutting cycle takes place in automatic mode Cutting range from 0 to 45 degrees to the right and left Head tiltable in two planes up to 45 degrees Quick angle lock 0, 15, 30 and 45 degrees to the right and left. Additionally, a built-in scale for setting the remaining angles Control panel with the possibility of programming all machine operations Display of blade speed, cutting counter, cycle time, engine current and possible error codes Two pneumatic vices with the possibility of transverse movement on the work table Built-in encoder enabling precise setting of the starting and ending points of the cutting cycle. Protected by a main switch and a minimum voltage coil, thermal motor overload protection Purpose: aluminum, light metals Optional equipment (additionally payable): Cgslowcd N Isim Ttyjt pneumatic vertical vice for blocking the material two pairs of cast iron V jaws for bundles of shapes and round bars (max. diameter 90 mm.) with tools for their assembly foot pedal with a 3m cable HSS steel blade with hard metal teeth, diameter 350x3.2x32mm with a 32mm hole chip extraction with a magnetothermal switch and a flexible tube with a power of 0.75KW Technical data: Disc diameter: 350 mm Vise opening width: 200 mm Disc speed: 1800/3600 rpm Disc motor power: 1.5/1.8 kW Working height: 865 mm Dimensions: 1100x920x1700 mm Weight: 266 kg

Condition: new, Year of construction: 2024, Functionality: fully functional, saw band length: 2,765 mm, saw band width: 27 mm, cutting speed: 70 mm/min, net weight: 289 kg, The IMET BS 300/60 manual band saw is a manual band saw designed for cutting medium-hard materials and for small and medium-sized productions. The machine can cut from 0° to 60° to the left. Colimswcd H Hs Ttyogt Adjustable stops The BS 300/60 is equipped with an adjustable stop system at 0°, 45° and 60° with a graduated scale for other angles. Blade protection The BS 300/60 blade is protected by a hinged blade guard that allows quick and easy blade replacement. Saw frame cutting IMET saws are equipped with a rigid, monobloc, cast iron cutting arc with a tubular cross-section and pulleys from 320mm, and the blade tension is 1700kg/cm2 with front adjustment and a control microswitch. Front vice Front clamp with quick lock and 130 mm high jaws and adjustable stop bar for serial cutting. Blade alignment Blade guide with carbide inserts and front bearings for optimal blade positioning. Use Safe start using the button on the handle, LED function control. Optional equipment (additional charge): Minimum lubrication may be required for each machine. Minimum lubrication eliminates coolant dispersion typical of using emulsifying oil. This has no effect on the service life of the blade. Adapter for synchronizing the movement of RTD, RTP and saw frame. Pneumatic vice with opening and closing controlled by a bail. Technical data: Tape width: 27 mm Vise opening width: 300 mm Tape dimensions: 2765x27x0.9 mm Tape speed: 35/70 m/min Tape motor power: 1.5/1.8 kW Working height: 940 mm Dimensions: 900x1700x1860 mm Weight: 289 kg

Condition: new, Year of construction: 2024, Functionality: fully functional, saw band length: 2,965 mm, saw band width: 27 mm, total height: 940 mm, cutting speed: 70 mm/min, net weight: 290 kg, Manual IMET GBS 242 GH Auto Cut band saw enabling angle cutting – arm swivelling to the right and left – and hydraulic feed. The machine is equipped with a manual vice with quick clamp, manual arm lifting, cooling system, two cutting speeds and smoothly adjustable feed. The cutting tool – bimetallic band 27 mm high is precisely guided in cubes made of sintered carbides. Basic data: Manual scissor type machine Maximum cutting diameter: ø 250 mm Working feed: gravity arm drop; smooth adjustment Arm lifting: manual Cutting at an angle: right 0° - 45° - 60°; left - 45° Band size: 2965 x 27 x 0.9mm Band speed: 2 cutting speeds 35/70 m/min Vise: manual - quick clamp GBS 242 GH has a large worktop with a rotating integrated with a handle designed to avoid cuts on the same ball bearing for easy rotation. Vise with adjustable guides, sliding laterally on the work surface and quick approach to the material being cut. The blade guides of the GBS 242 GH model are equipped with carbide inserts and additional front bearings for optimal blade positioning. The bimetal blade measures 2965 x 27 x 0.9 mm and works at a speed of 35 to 70 meters per minute, making it the ideal tool for processing steel and cast iron. The controlled lowering system is equipped with automatic operation with a 3-position selector for: Manual cutting Quick approach to the material Automatic cutting with autonomous lowering, adjustable stop and end cut microswitch Standard equipment: cooling system bimetallic tape - 1 pc. in the machine instruction manual in Polish CE certificate Additional equipment for an additional fee: roller feeders measure with bumper connector oil mist lubrication system (micronizer) tensometer for precise adjustment of the tape tension Csliswcd Eism Ttyjgt Technical data: Tape width: 27 mm Vise opening width: 290 mm Tape dimensions: 2965×27×0.9 mm Tape speed: 35/70 m/min Tape motor power: 1.1/1.3 kW Height working: 940 mm Dimensions: 1500x1250x1700 mm Weight: 290 kg

Condition: new, Year of construction: 2024, Functionality: fully functional, saw band length: 2,720 mm, saw band width: 27 mm, cutting speed: 70 mm/min, working height: 900 mm, warranty duration: 12 months, net weight: 260 kg, Manual IMET GBS 240 GH Auto Cut band saw enabling angle cutting – arm swivelling up to 60° to the right – and hydraulic feed. The machine is equipped with a manual vice with quick clamp, manual arm lift, cooling system, two cutting speeds and smoothly adjustable feed. Cutting tool – bimetallic band 27 mm high is precisely guided in cubes made of sintered carbides. Basic data: maximum cutting diameter: ø 240 mm working feed: gravity arm drop; smooth adjustment arm lift: manual angle cutting: Right 0° - 45° - 60° cutting band dimensions: 2720 x 27 x 0.9mm band speed: 2 cutting speeds 35/70 m/min. vice: manual - quick clamp GBS 240 GH has a large worktop with a rotating integrated with a bow designed to avoid cuts on the same ball bearing for easy rotation. Vice with adjustable guides, sliding laterally on the work surface and quick approach to the material to be cut. The bimetal blade measures 2730x27x0.9mm with a working speed of 30 to 70 m/min making it the ideal tool for machining steel and cast iron. The controlled lowering system is equipped with automatic operation with a 3-position selector for: Manual cutting Quick approach to the material Automatic cutting with autonomous lowering, adjustable stop and end cut microswitch. Standard equipment: cooling system bimetallic tape – 1 pc. in the machine user manual in Polish Additional equipment at extra charge: roller feeders oil mist lubrication system (micronizer) tensometer for precise adjustment of tape tension Technical data: Tape width: 27 mm Vise opening width: 270 mm Tape dimensions: 2720×27×0.9 mm Tape speed: 35/70 m/min Tape motor power: 1.2 kW Working height: 900 mm Dimensions: 680x1400x1800 mm Cslim Tjwcd Dlotyjgt Weight: 260 kg