Used Benford Pt 7000 for sale (54,000)

Condition: excellent (used), Year of construction: 2005, operating hours: 5,800 h, Functionality: fully functional, machine/vehicle number: 0-250-04-2333, travel distance X-axis: 3,310 mm, travel distance Y-axis: 1,735 mm, travel distance Z-axis: 220 mm, TECHNICAL DATA Dolim Ijuh Uyqo Nbout Table length: 2750 mm table width: 1050 mm Workpiece thickness: 100 mm X-axis: 3310 mm Y-axis: 1735 mm Z-axis: 220 mm Tool holder: HSK-F 63 Magazine: 8-position plate Unit: 2 spindles Drill: (6+4) x 32 X-axis speed: 60 m/min Y-axis speed: 50 m/min Z-axis speed: 20 m/min Standard compressed air quality: according to ISO 8573-1 quality class 3 Connection: R 1/2" Pressure in the supply line: 7 bar Compressed air consumption: approx. 100-200 l/min Suction connection: Ø 200 mm Height: 2110 mm Total extraction capacity: min. 3170 m³/h Air speed: min. 28 m/s Pressure loss: min. 2000 Pa MACHINE DETAILS Loading dimensions: 5400 x 2300 x 2400 mm Machine weight approx.: 3600 kg Protection class: IP53 Operating voltage: 3 x 400 Volt, ±5% Frequency: 50 Hz External power supply: 32 A Recommended fuse: 35 A Total connected load approx.: 17.5 kW FUNDAMENT Surface pressure: in the area of the support points 1.2 N/mm² Floor covering: concrete quality B25, compressive strength ≥ 200 mm

Condition: excellent (used), Functionality: fully functional, Year of construction: 2018, operating hours: 6,336 h, load capacity: 2,000 kg, lifting height: 4,650 mm, free lift: 1,600 mm, load center: 500 mm, mast type: triplex, construction height: 2,050 mm, gearing type: automatic, battery capacity: 375 Ah, battery voltage: 24 V, fork length: 1,200 mm, tire condition: 100 %, empty load weight: 1,400 kg, total height: 2,050 mm, Linde L16 electric stacker built in 2018 with triplex mast, initial lift and free lift battery 2021 with 81% remaining capacity. Device has been checked and serviced and overhauled by a specialist dealer. Mast is triplex mast and a lifting height of 4.65m. Load capacity 1600kg. High-lift truck has a full free lift (forks move up without the mast extending up to 1600mm). The device also has an initial stroke for small bumps and ramps. Pallet truck is equipped with a weighing system!! Very good maintenance condition. No repair backlog. Hydraulic seal. Battery C5 Tested with 81% remaining capacity (C5 test) 309Ah / 375Ah see test result New drive wheels/support wheels. Technical data: Manufacturer: Linde Model: L16AP Year of construction: 2018 Hours. 6336 Load capacity: 1600kg Height 2050 Fork length: standard Lifting height 4650mm Battery: 81% remaining capacity (c5 test) built in 2021 Mast: triplex Duolsu Shuljim I Nbet Full free lift Initial stroke New wheels. Hydraulics tight. Driver's platform (foldable) with integrated HF charger 24v 30A WITH SCALE!! UVV is possible due to the good technical condition. Transport possible!! Please ask.

Condition: good (used), Year of construction: 2005, OMGA opti cut IDC000080 - Manufacturer: OMGA - Year of production: 2005 Duelst D Dukeim I Nbjt - including table before and after - Control cabinet - Working condition

Condition: new, Year of construction: 2024, Functionality: fully functional, Vertical Cartoning Machine / Casepacker BOX GROUP TOM - newly manufactured and in storage = short delivery time Powerful, fully automated vertical cartoning machine / casepacker designed for cartoning a wide range of products into a cardboard box. The device ensures reliable cartoning of bags or boxes in 1 or 2 rows. Ideal for connecting behind a bagging machine or cartoning machine The frame welded structure contains all the necessary mechanical devices for moving boxes, placing and counting bags/boxes. The unit includes a fully fitted electrical switchboard and protective covers with safety sensors including an indication on the touch panel. The cartoning machine is controlled by a freely programmable BaR control system with a touch screen. The standard version of the system enables archiving of up to 100 programs. The machine can be supplemented with many optional accessories according to customer requirements. Line includes: BOX GROUP TOM - cartoning machine / casepacker CARTON ERECTOR PATERNOSTER - erected box lift Dujlim Isub R Nne Nbjt CARTON SEALER possibility to connect to robotic palletisation and primary cartoning / packaging machine

Condition: good (used), Year of construction: 2008, EMCO CONCEPT MILL 450 Year 2008 100 % functional Immediately available Weight-3800 kg. Dujlim I Njugl Tlobet

Condition: like new (used), Year of construction: 2017, Functionality: fully functional, operating pressure: 350 bar, total length: 12,000 mm, high-pressure hose length: 10,000 mm, total height: 9,850 mm, total width: 6,500 mm, empty load weight: 150 kg, fuel: regular/benzine 91, power: 16 kW (21.75 HP), For sale is a demonstration machine in mint condition, has been on the shelf for approx. 6 years. Honda engine. Dusliorg Hatem I Nbet Can be checked on site.

Year of construction: 2007, Condition: good (used), 1. Loading BARGSTEDT O TSH200 / D / 30/12 2. The first HOMAG OPTIMAT KFL 525 / M1 / ​​C machine 3. HOMAG OPTIMAT TDL 510 / C turntable Doleik H Egeim I Nbout 4. Drug machine machine HOMAG OPTIMAT KFL 526 / M2 / C 5. HOMAG OPTIMAT TDL 510 / C turntable 6. WANDRES THE BRUSH 7. Unloading BARGSTEDT O TSH200 / D / 30/12 The machine is in constant use Machine immediately

Condition: new, Year of construction: 2024, Functionality: fully functional, cutting range round at 90°: 650 mm, warranty duration: 12 months, net weight: 8,000 kg, Cutting range: Diameter : 650 mm, axh section 800x650 mm Main drive motor 7,5 kW. Belt drive unit reducer - inverter. Body of the machine tool Construction of thick-walled sheets welded and reinforced with steel sections to ensure high stability and durability of the base. In the body there are containers with oil and cooling emulsion. Receiving table at the working vise with dimensions 800x500. Arm guidance Vertical columns made of properly selected profile steel. Guiding of the arm - precision rolling guides with preload. Arm movement controlled by two ball screws mechanically connected to each other by reducers and servo motor. The machine will be equipped with a mechanism for hydraulic relief of the arm holding bolts to reduce the pressure on the ball screw nuts, resulting in longer service life. The use of the arm feed drive with ball screws provides constant control over the feed speed especially at minimum cutting speeds, setting the feed speed parameter from the control panel. The machine will be equipped with arm descent speed measurement displayed on the desktop and bend control. The belt guiding control (bend control) will be linked to the arm feed drive mechanism. When the belt deflects, the feed speed will be automatically corrected, after it returns to the correct value, the feed will automatically return to the original value. When the set value of the tape deviation is exceeded (bevel cutting), the machine will stop the cutting process and visually (indicator lamp) will notify the problem. Standard equipment Cutting arm guided on rolling guides Reducer - inverter Lifting and lowering of the cutting arm controlled by ball screws, Hydraulic clamping of working vice and feeding vice Double-half vise holding the material in front of and behind the cutting belt Bend Control Hydraulic tensioning of the cutting belt with compensation for its elongation; Feeding roller table on the body of the machine length of 1.5 mb Automatic feeder drive screw (single feeding up to 1000 mm) is only available in system with PLC and inverter Adjustment of clamping force of vices Roller receiver length 1.5 mb (receiving table) Feeding table length 3 mb with driven rollers equipped with vertical rollers on the input and output - controlled from the machine desktop (additionally equipped with a mobile desktop at the roller conveyor) Laser cutting line Chip extractor (directed to the right side) PLC with liquid crystal display; cutting belt speed measurement (NC) Full protection, complying with CE safety mark. Cooling system; Duelsvf Icfjim I Nbst Cutting belt; DTR

Condition: good (used), Year of construction: 2007, operating hours: 74,627 h, Functionality: fully functional, clamping force: 3,500 kN, screw diameter: 70 mm, displacement volume: 1,212 cm³, injection pressure: 1,877 bar, plate length: 710 mm, plate width: 630 mm, Machine was in use until December 2024! TECHNICAL DETAILS Screw diameter: 70 mm Injection pressure: 1,877 bar Displacement: 1,212 cm³ Clamping force: 3,500 kN Mold holder Distance between the tie bars: 710 x 630 mm Minimum mold thickness: 330 mm Maximum tool thickness: 710 mm Maximum distance between the clamping plates: 1,385 mm MACHINE DETAILS Total length: 7,700 mm Total width: 2,000 mm Total height: 2,300 mm Total weight: 16,000 kg EQUIPMENT Dslim Isvvtple Nbsut - Documentation - Manuals

Condition: new, Year of construction: 2024, Push feed optimizing saw for the complete optimization of the wood and the elimination of the defects. COSTCUTTING OPTIMIZING SAW Superpush 200 is a true technological evolution of traditional cutting methods. It is able to increase productivity considerably, reduce staff usage to a minimum, and improve wood yield. EXTREMELY ROBUST Very robust and reinforced steel structure. Special 30° inclined plane to favour the loading and keep the work piece squared. Pusher carriage dimensions mm. 300x345x25. Toothed belt width 50 mm. with 33 steel strips inside. Horizontal deposit/marking plane with width mm. 300. TECHNOLOGICALLY INNOVATIVE Electronic system composed by a computer connected in real time to a last generation numeric control. Software running on Windows. Complete with 5 qualities managing. 19” LED colour screen. Tele-service trough internet. + Macro Excel included. FAST Total optic system. Brushless servo driver motor for the pusher. Intelligent pressure beam. Adjustable cutting speed. Dslim Iefg U H Ns Nbeut RELIABLE AND SAFE Transmission system with sliding on double hardened and rectified guides. “Skf” sliding bearing with double anti-dust protection and automatic lubrication. Electric box separated from the machine and self-standing. Independent pneumatic regulations to adapt to different types of working. Safety closing protection on back side.

Year of construction: 1997, Condition: used, Year of manufacture 1997 Serial number 9937 Working area X 3100mm Working area Y 600mm Working area Z 850mm Main motor 4 x 5Kw 5-axis machine Number of milling spindles 4 Number of revolutions max 1800 1 table 3000mm x 550mm Duelimsmhf E Ns I Nbjt

Condition: used, Functionality: fully functional, VanKel VK7000 Dissolution tester. The dissolution tester of the brand Vankel type VK7000 is designed for in vitro monitoring of the rate and extent of drug absorption which are dependent on the dosage form. This dissolution tester can be used for optimization of therapeutic effectiveness during product development and stability assessment and for the evaluation of production quality to guarantee uniformity between production parties. Duolim Ieuax Txe Nbet Technical specifications: Voltage: 115V, 60Hz Power: 3A Temperature range: 0 °C – 75 °C Speed: 10 – 250 rpm External dimensions (W) x (D) x (H): 62.5 x 53.5 x 93 cm Technical specifications Vankel VK750 controller Voltage: 115V, 60Hz Current: 15A External dimensions (W) x (D) x (H): 18.5 x 36.5 x 19.5 cm Good working condition. Please check out our other listings as well.

Year of construction: 2008, Condition: used, The Opto-DesQ measuring table is equipped with a special camera system and image recognition software. This ensures highly accurate measurement results. Duolim Ishk S R Io Nbst results. A specially ground granite slab is used as a base for the measurement granite slab is used as a base for the measurements (other dimensions available on request). The software allows to software also allows for the measurement of irregular elements. Distances between centres of rays, ellipses and angles of any lines can be measured. between centres of radii, ellipses and angles between any lines. The following are measured The software also measures hole positions and depths. Control of the dimensions of the length, width, angularity, position of holes, milling, The control of dimensions of length, width, angularity, position of holes, milling, grooves based on the measured value of the existing value and its comparison with the value After the measurement, protocols are created. After the measurement protocols and a drawing are created. As As an additional option, information can be provided on the adjustment of the drilling machine spindles.

Condition: good (used), Year of construction: 2014, operating hours: 50,000 h, Functionality: fully functional, Feed water deaeration unit, partial deaeration, with equipment and switch box. Available in January 2025. Duolistx Ub Eom I Nbot

Condition: new, Functionality: fully functional, mileage: 10 km, fuel type: diesel, color: white, Year of construction: 2024, We export new and used vehiles all over Europe. Our offer includes passenger cars, vans, trucks, construction and agricultural equipment. We speak English, Polish, Ukrainian Selected equipment Cabin exterior - Super Space Cab with galvanized steel bumper, tinted glass and electrically operated windows side. Heated main and wide-angle mirrors electrically. Cabin width 2490 mm. - Air cabin suspension with integrated shock absorbers. - LED headlights with impact-resistant Lexan lenses. - Skylights. Two stylish light clusters with large glass lampshades, completely integrated with the rounded ones corners of the cab roof. Aerodynamics - The fixed roof deflector - Side covers. One side tilts, the other side is mounted on Constant. Colors Roof deflector color: Brilliant White. - Color of side covers: Opalescent white. Cabin interior - Driver's seat with air suspension " Luxury Air. Armchair with high backrest and adjustable support arms. Two-stage heating. - Adjustable armrest on the inside of the passenger chair - Drawer with a refrigerator with a capacity of 42 l, under the lower bunk. Delim I Njuf Sf Esbsut - Air nozzle connector at the rear of the seat console. - Storage compartment under the lower bunk: left side - airtight 150 l container with external door and open 60 l container; right side - open container 150 l with external door and open container 85 l; median part - open 25 l container with bottle holder at the front and a 65 l cabinet with a movable partition, next to the refrigerator. - Lower bunk with 'Xtra Comfort' mattress with springs covers, thickness 150 mm. - Sleeping compartment with upper bunk, with step. Communication and information management regarding driving - Preparation for equipment for satellite communication with intended for the German Maut tax system, consisting of cabling to the module installation site on-board unit (OBU) and the short digital communication module range (DSRC). - Digital (intelligent) VDO DTCO tachograph with receiver GNSS (Global Navigation Satellite System) and dedicated short-range communication module (DSRC) - GPS-based Predictive Cruise Control DAF Night Lock. - Emergency hammer to get out of the vehicle in emergency situation. Suspension and axles Axle load monitoring - Front axle: tire size 315/70R22.5, Goodyear - Driven rear axle: tire size 315/70R22.5, Goodyear Drive system MX-13 engine, 6-cylinder diesel engine 12.9 l with torque boost. Power 355 kW (483 HP) at 1600 rpm. Maximum torque 2500 Nm at 900-1125 rpm. - Rear axle ratio 2.21. Braking system - MX Engine Brake. Chassis Wheelbase 3.80 m / rear overhang 0.99 m. Battery box in the rear overhang. Without spare wheel basket. Aluminum fuel tanks with integrated step 845+430 l, height 620 mm. Coupling and equipment for trailer connection JOST saddle type JSK42, cast iron, height 150 mm with plate mounting 12 mm. King pin diameter 2 inches. Power take-off shaft (PTO) Direct control of the gearbox PTO, without gearbox PTO. 24V power supply - 80 A alternator, 2 × 210 Ah AGM batteries. Total vehicle weight and total combination weight - Maximum technical total weight of the vehicle depends on chassis weight 19,500 kg - Max. GCW of the set depending on the drive system 44,000 kg, class 2

Condition: new, Max saw blade diameter: 350 mm Max cutting height: 115 mm Worktable dimensions: 560x800 mm Duelim Iji Dtyrs Nbst Aluminum trolley dimensions: 1200x360 mm Saw angle: 0-45° Max cutting height at 45° with 350mm saw: 80mm Main disc speed: 4000 rpm Motor power: 4 kW Power: 380V

Condition: excellent (used), Perfectly preserved refrigerated display cabinet, gas R 290. dimensions external 205x245x 85, internal 150x240x65. We speak German, English and ex YU languages. Contact possible also via WatsApp Duslist Txnqsm I Nbot

Condition: good (used), Year of construction: 2018, Functionality: fully functional, Trimming saw KP-500 OPTIM Dueliett R Amjm I Nbet input conveyor 6200mm Output conveyor 6000mm 4 pcs ejectors motor 12Kw r.v. 05/2018

Condition: new, Year of construction: 2023, operating hours: 0 h, machine/vehicle number: 0, Strojplast semi-automatic packaging system for wood briquettes Structure of the packaging system offered here: - Downstream of an RUF briquetting system. - Incl. Strojplast stack manipulator, Smartpal 2000. - Strojplast offers turnkey solutions for the packaging of wood briquettes. - Manual to fully automatic solutions are available on a modular basis. Dujlim Ieqbtqgj Nbot - For all common wood briquette formats up to 6 to/h - Color RAL 7031, RAL 7040, powder coating - Operator language: German / English (others on request) All systems are assembled in the manufacturer's factory and extensively tested for function. Only then, or after pre-acceptance, are they dismantled in modules and shipped to the customer, thus avoiding time-consuming and cost-intensive time-consuming and costly assembly/commissioning on the customer's side. - Delivery time: approx. 4-5 months, depending on version - Price on request ----- Strojplast semi-automatic packaging system for wood briquettes Structure of the packaging system offered here: - Downstream of an RUF briquetting system. - Incl. Strojplast stack manipulator, Smartpal 2000. - Strojplast offers turnkey solutions for the packaging of wood briquettes. - Manual to fully automatic solutions are available on a modular basis. - For all common wood briquette formats up to 6 tons per hour - Color RAL 7031, RAL 7040, powder coating - Operator language: German / English (others on request) All systems are assembled in the manufacturer's factory and extensively tested for function. Only then, or after pre-acceptance, are they dismantled in modules and dispatched to the customer, thus avoiding time-consuming and cost-intensive time-consuming and costly assembly/commissioning on the customer's side. - Delivery time: approx. 4-5 months, depending on version - Price on request

Condition: like new (used), Working width 1350 mm The machine is in excellent, new condition as shown in the pictures. Duelijuuitgsm I Nbst

Condition: new, Year of construction: 2024, Functionality: fully functional, PTR1600L Carmec Pressure tester for cylinder head and block - new machine Hydraulic tray lifting, motorized tray rotation. Max. cylinder head dimensions: 1350 mm x 300 mm × 395 mm Max. cylinder head weight: 300 kg Adjustable pressure air test: 0 bar -10 bar Adjustable working temperature: 0 - 90°C Stainless steel tank capacity: 540 Liter Heating power: 2× 4,0 kW Hydraulic unit power: 0,75 kW Rotation motor power: 0,18 kW Maximum vertical travel distance: 600 mm Up and down travel time: 10s Rotation speed: 4 RPM Delieu S Eqnom I Nbjut Supply voltage: 220-440V 3Ph+E ( +/- 10% ) Frequency: 50-60 Hz Operating voltage: 24 V AC Empty tank: 440 kg Machine dimensions: 2050 mm × 1120 mm × 1650 (max. H) mm If you are interested, please contact me! More machines for sale: Berco, Comec, A-M, Carmec, Kwik-Way, Serdi, PEG Connecting rod boring, cylinder boring, honing machines, valve seat milling, parts washer, valve grinder, line boring, valve guide press machine, pressure test bench, resurfacer, vacuum tester, valve spring compressor, crankshaft polisher machines

Condition: new, Year of construction: 2024, overall weight: 1,520 kg, fuel type: diesel, tank capacity: 260 l, color: black, power: 132 kW (179.47 HP), output current: 250 A, output voltage: 400 V, output frequency: 50 Hz, type of output current: three-phase, total length: 2,900 mm, total width: 1,100 mm, total height: 1,750 mm, motor speed: 1,500 rpm, motor manufacturer: FPT Iveco NEF67TM3A, type of cooling: water, New Diesel Electric Generator FROM STOCK! Are you looking for a reliable source of electricity? Look no further! Buy from manufacturer directly. Tehnolink doo as EUROPEAN producer offers a new diesel electric generators per your request. Perfect for all your needs, whether it’s for construction sites, camping, or as a backup power source for your home. Features: - High efficiency and durability - Quiet and stable operation - Easy portability - Environmentally friendly design - Various models with power to suit your needs Dueliot Ivvbem I Nbjt Don’t miss the opportunity to ensure reliability and safety with our diesel generator! For more information or to arrange a viewing, feel free to contact us.

Condition: excellent (used), Year of construction: 2000, Machine SCM CONCEPT 2000 Dolimot Uk Nvs I Nbeut

Condition: new, Year of construction: 2024, overall weight: 2,500 kg, fuel type: diesel, tank capacity: 350 l, color: grey, power: 160 kW (217.54 HP), output current: 400 A, output voltage: 400 V, output frequency: 50 Hz, type of output current: three-phase, total length: 3,500 mm, total width: 1,250 mm, total height: 1,900 mm, motor speed: 1,500 rpm, motor manufacturer: IVECO NEF67TM7.S500, type of cooling: water, New Diesel Electric Generator FROM STOCK! Duelimot Ig Tde I Nbet Model : Iveco IV.220.KA, power 200kVA/160KW, canopy type for outdoor use; Are you looking for a reliable source of electricity? Look no further! Buy from manufacturer directly. Tehnolink doo as EUROPEAN producer offers a new diesel electric generators per your request. Perfect for all your needs, whether it’s for construction sites, camping, or as a backup power source for your home. Features: - High efficiency and durability - Quiet and stable operation - Easy portability - Environmentally friendly design - Various models with power to suit your needs Don’t miss the opportunity to ensure reliability and safety with our diesel generator! For more information or to arrange a viewing, feel free to contact us. If you have any additional information you'd like to include or changes you want to make, just let me know! p.s available other models as well!

Condition: excellent (used), Year of construction: 1996, Functionality: fully functional, Full SCM line Duslimjt T Sq Ee I Nbst