Premelter

IMA

Condition: ready for operation (used), Year of construction: 2013, machine/vehicle number: 08450, functionality: fully functional, operating hours: 15,861 h, Edge banding machine + BARBARIC LX U4 B2200 return system! The machine is equipped with the following units: Bodpezxgfzefx Ammsdg Joint milling VTG gluing unit Quick-Lock glue application Pre-melting tank with automatic granule feed Cutting unit Flush/profile milling KFA-x30 contour milling unit Profile and joint drawing blades TECHNICAL DETAILS Workpiece thickness: 8–60 mm Feed rate: approx. 6–30 m/min MACHINE DETAILS Power supply: 3 N PE Operating voltage: 400 V Power frequency: 50 Hz Rated power: 32 kW Rated current: 69 A Operating hours of edge banding machine: approx. 15,861 h (as of 2023) BARBARIC LX U4 B2200 return system Year of manufacture: 2014 Serial No.: 2130742-102 Operating hours: approx. 8,997 h (as of 2023) EQUIPMENT Automatic 12-position edge magazine Pre-melting tank with automatic granule feed

Condition: ready for operation (used), Year of construction: 2013, This IMA NOVIMAT I /G80/390/R3 edgebander was manufactured in 2013. It features dual 4.5 kW motors at 150 Hz, achieving speeds up to 9000 rpm. Capable of handling edge heights from 14 to 65 mm and roll diameters up to 850 mm, it's ideal for precise edgebanding needs. Consider the opportunity to buy this IMA NOVIMAT I /G80/390/R3 edgebander. Contact us for more information about this machine. Additional information • Motor Power: 2 x 45 kW, 150 Hz Bodpfxezxzrvo Ammodg • Motor Speed: 9000 rpm • Power Supply: 230 V • Heating Power: 6 x 500 watts • Adjustment Range: Vertical approx. 17 mm, Horizontal approx. 30 mm • Stroke: Max. 8 mm • Roll Diameter: Max. 850 mm • Edge Height: 14 – 65 mm • Workpiece Projection: Min. 30 mm + edge thickness, Max. 80 mm including edge thickness • Workpiece Length: Min. 130 mm • Workpiece Gap: Min. 300 mm • Workpiece Distance: Min. 990 mm • Workpiece Thickness: Min. 8 mm, Min. 12 mm with tracing wheel, Max. 80 mm • Single Tracing Workpiece Projection: Min. 30 mm • Double Tracing Workpiece Projection: Min. 38 mm for max. 4 profiles, Max. 50 mm • Cutter Head Diameter: 125 mm • Motor Shaft: 30 x 68 mm diameter • Internal Thread: M16, Depending on motor, left or right • Cutting Cross-section Motor Power: 0.20 kW, 200 Hz 400 V, 12000 rpm for max. 195 mm², Option: 0.66 kW, Extension to max. 1100 mm² • Tool Diameter: 160 mm / 48 teeth • Swivel Range: 0 and 25 degrees • Workpiece Speed: Max. 30 m/min for an edge cross-section of 3 x 45 mm • Edge Overhang: Top edge, max. 3 mm, Bottom edge, max. 2 mm for straight edges • Edge Material: Edge, max. 4 mm for wood and plastic; Aluminum, max. 3 mm

Condition: used, Year of construction: 1994, Storage location: Nattheim Bdjdpfx Aowmm Nremmsg

Condition: used, machine/vehicle number: 007842, X axis working area: 5000 mm Y axis working area: 1200 mm Working Table: Pod and Rail Main Electrospindle power: 18 KW Number of controlled axes: 4 axes Maximum edge height: 64 mm Total number of drilling spindles: 14 Total number of tool changer positions: 18 Bdsdpfsyhbiusx Ammjg

Condition: good (used), Year of construction: 1989, Machine with full equipment Length approx. 9 m Jointing Rip sawing Dadoing Bdodpfef Ua R Hjx Ammog Rounding Edge profiling Scraping Edge profiling

Condition: used, machine/vehicle number: 008662, Position 1: Single Edgebanders IMA-NOVIMAT CONTOUR I/G80/790/R3 Bedpezmmtnsfx Ammsdg Position 2: Panel Return Systems IMA-NOVIMAT CONTOUR I/G80/790/R3

Condition: used, Door panel postforming line Note: The line began series production in 2022; at this point, all machines were technically synchronized and, if necessary, overhauled. Door panel postforming line consisting of: Portal loading system Bdodpfx Aszuziyemmog Manufacturer: Kraft Year of manufacture: 2019 Technical data - with vacuum lifter - 2 infeed roller conveyors - one transport roller conveyor for further transport Wide belt sanding machine Manufacturer: Costa Type: KK7 CT CT 1350 Year of manufacture: 2018 consisting of: Wide belt sanding machine, sanding from below Technical data - contact roller - electronic shoe sanding unit - cleaning brush - intermediate transport belt, length approx. 3000 mm Wide belt sanding machine, sanding from above Technical data - identical equipment Complete formatting, laminating and postforming line consisting of: Roller conveyor system Manufacturer: Kraft Year of manufacture: 2019 Technical data - 3 individual elements - centering station Double end profiler Manufacturer: IMA Type: FBA/II/740/A Year of manufacture: 2018 Technical data - equipped with infeed conveyor and aligning station - saw unit below - trimming unit - edge trimming unit - prism milling cutter - joint milling cutter - cross edge milling unit - 3 profile milling units - brushes Laminating line consisting of: Infeed conveyor Manufacturer: Kraft Year of manufacture: 2019 Glue application machine Manufacturer: Bürkle Type: DAK1300 Year of manufacture: 1992 Technical data - mechanically overhauled in 2018 - control system completely overhauled in 2022 - with infeed table, manufacturer Kraft - steel platform with stairs and various pumps - glue melting unit GWK Eco 03A Infeed table for laminating line Manufacturer: Kraft Year of manufacture: 2019 Laminating line Manufacturer: Bürkle Type: EKMH 1300 Year of manufacture: 1998 Technical data - new Siemens Simatic KMG Touch control system - Bürkle GLK press calender - incl. film holder and saw for overhang - working width 1300 mm - 2 temperature control units GWK - column swivel crane for loading paper rolls - extraction conveyor Postforming line Manufacturer: Homag Technical data - infeed table - with 2 saw units, horizontal and vertical - intermediate buffer with 4 levels - infeed to the postforming machine - 2 identically constructed processing sides with glue application - PU pre-melting unit Nordson / VersaBlue, year 2020 and 2004 - pressure zone with revolving magazine for various profiles - various milling units and flap brushes - 2 cooling units BEKO Bekoblizz LC, year 2020 Belt conveyor with inspection system - swivel arm with vacuum suction cup - inspection station for optical inspection of the workpiece Portal destacking system Manufacturer: Kraft Technical data - with vacuum portal and 3 destacking stations Note: The technical data and descriptions are copies of the original order confirmation. The information provided is for informational purposes only and is non-binding.

Condition: used, Factory-reconditioned edge processing line for 3 mm edges Manufacturer: IMA Type: Combima Consisting of: Machine 1: Used edge processing machine from IMA, type COMBIMA Factory-reconditioned with a 12-month warranty - Working width max. 1,500 mm, edge thickness approx. 0.3 - 3 mm - Rolling needle bearing chain, drive with 3 kW motor, steplessly adjustable from 9 - 45 m/min - Motorized width adjustment with electronic setpoint and actual value display - Double trimming unit with 2 motors, 4.4 kW, 100 Hz - Milling unit with 1 motor, 4.4 kW, 100 Hz - Hot melt adhesive unit with 2-roller magazine and automatic Quickmelt hot melt adhesive feed - Trimming unit with 2 motors, 0.4 kW - Pre-milling and flush milling unit with 2 motors, 1.5 kW - Chamfering unit with 2 motors, 0.6 kW - Profile drawing blade unit Bdodjzuyqvjpfx Ammeg - Straight drawing blade unit - Edge sanding/buffing unit - Beckhoff control system with screen - Electronic converter 100 Hz, manufacturer: KEB - Electronic converter 200 Hz, manufacturer: KEB - 1 used rotating device for changing from longitudinal to transverse - Factory-reconditioned with a 12-month warranty - Max. panel length 2,500 mm, max. panel width 1,500 mm Machine 2: Used edge processing machine, manufacturer: IMA, type COMBIMA Factory-reconditioned with a 12-month warranty - Working width max. 3,000 mm, edge thickness approx. 0.3 - 3 mm - Rolling needle bearing chain, drive with 3 kW motor, steplessly adjustable from 9 - 45 m/min - Motorized width adjustment with electronic setpoint and actual value display - Protective milling unit with motor 3.3 kW, 100 Hz - Double trimming unit with 2 motors, 4.4 kW, 100 Hz - Enclosed gluing unit with double roller magazine and automatic Quickmelt hot melt adhesive feed - Trimming unit with 2 motors, 0.4 kW - Pre-milling and flush milling unit with 1 upper and 1 lower motor, 0.4 kW - Chamfering unit with 2 motors, 0.4 kW - Copy milling unit with 2 motors, 150 W - For milling off strip overhangs on front and rear lower workpiece profiles, copy milling unit with 2 motors, 150 W - For milling off strip overhangs on front and rear upper workpiece profiles, profile drawing blade unit - Straight drawing blade - Buffing unit - Center support - Pull-out rollers 800 mm - Beckhoff control system with screen - Electronic converter 100 Hz, manufacturer: KEB - Electronic converter 200 Hz, manufacturer: KEB Delivery time after order placement approx. 4-6 months (depending on current workload and scope of desired work). Individual machine configurations are possible according to customer requirements, as the machines are disassembled down to the base frames and reassembled after replacing all wear parts.

Condition: used, Year of construction: 2010, - Release agent application, top and bottom - Scoring saw with 2.2 kW motor - Trimming unit with 8.0 kW motor - Double milling unit with 2 motors, each 4.5 kW - Gluing unit - End trimming unit - Flush trimming unit - Multi-function unit - Multi-profile edge trimming unit - Spray nozzles, top and bottom - Flat edge trimming unit - Buffing unit - Grooving unit Double-sided edge banding machine Manufacturer: IMA Type: Combima/II/390/B/L12 Year of manufacture: 2010 For longitudinal and transverse feed - 2 low-maintenance precision roller chains with 75 mm wide and 85 mm long, rubber-coated chain plates, with cams - Spacing 1080 mm. Pneumatically adjustable to heights of 8, 16 or 24 mm. ICOS OPEN control system - Max. feed width 3,300 mm - Program-controlled master + slave width adjustment - Fixed stop on the left in feed direction Workpiece dimensions - Min. feed width 244 mm (for longitudinal processing) - Max. workpiece width (chain extension) 1,300 mm - Min. workpiece thickness 8 mm - Max. workpiece thickness 45 mm (with copying function) / 60 mm (without copying) Edge material: - Min. height 14 mm, max. height 65 mm - Roll material min. thickness 0.3 mm, max. thickness 3 mm Strips and edgebanding: - Min. thickness 0.8 mm, max. thickness 12 mm Feed speed - 10 - 50 m/min. with frequency-controlled drive. Infeed device - with 5 top-mounted, inclined and driven rollers. Center support with roller track - automatically lowerable and automatically centering. Equipped on each side with: Release agent application, top and bottom Scoring saw with 2.2 kW motor, 100 Hz, 6,000 RPM, pneumatically controlled. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Trimming unit with 8.0 kW motor, 100 Hz, 6,000 RPM. - Electronic positioning for stepless horizontal adjustment. Double milling unit with 2 motors, each 4.5 kW, 150 Hz, 9,000 RPM. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Gluing unit for hot melt adhesive - With single roll/edgebanding magazine for roll material up to 3 mm and edgebanding up to 12 mm - 2-fold roll magazine for roll materials up to 3 mm (can be attached to the single roll magazine) - Horizontal roll holder Bodpfxszuyqie Ammjdg End trimming unit - Mounted on the upper pressure beam, with 2 motors, each 660 W, 200 Hz - Pneumatic swivel 0 + 25 for straight and miter cuts. - Automatic adjustment for miter cuts with two different edge thicknesses (e.g. 0.4 and 1.2 mm) and for "edge overhang" for copying with edge thickness 1.0 - 3.0 mm. Automatic adjustment to the feed speed 20+30 m/min. Flush trimming unit 08.0555 - With 2 motors 1,850 W, 200 Hz, 12,000 RPM. Multi-function unit 08.353 - NC controlled with 2 motors, with automatic tooling for 4 profiles. Multi-profile edge trimming unit - with automatic tooling for 4 profiles via fixed-point control Spray nozzles, top and bottom - for applying cleaning agents Flat edge trimming unit Buffing unit - With 2 motors, each 180 W, 50 Hz, 1400 RPM. 1 Grooving unit - With 4.5 kW motor, 150 Hz, 9,000 RPM. - Horizontal and vertical adjustment manually with mechanical digital display - Pneumatic activation control - Manual swivel 90 ICOS open - PC-based control system with integrated PLC and electronic path control. - User-friendly interface with Windows standards - Simple, component-oriented

Condition: used, Year of construction: 2010, - Application of release agent, top/bottom - Joint milling unit - Gluing unit - Trimming unit - Copy milling unit SKF-L - Profile trimming blade unit - Spray cleaning agent - Self-adjusting trimming blade unit - Buffing unit Single-sided edge banding machine Manufacturer: IMA Type: Advantage 310 Year of construction: 2010 Technical data Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65* / 150 mm *at a max. workpiece thickness of 25 mm - Workpiece thickness: min. 8 mm, 12 mm with profile trimming blades max. 40 mm (with MFA 08.346), 60 mm (with SKF) - Smallest workpiece: 65 x 300 / 150 x 150 x 19 mm - Machining allowance per workpiece edge: 0 - 5 mm (observe max. chip cross-section) - Workpiece shape: right-angled - Material: chipboard, MDF - Surface material: direct coating (melamine resin paper), paper, film, veneer Edge material - Roll material without film: Paper edges & plastic edges: 0.3 - 3.0 mm Bodpfx Amezuyp Eemodg Veneer edges: 0.5 - 3.0 mm - max. edge cross-section: 150 - 180 mm² - Cut edge strips: Strips: 3.0 - 8.0 mm - max. strip cross-section: 520 mm² - Edge height: min. 12 mm, max. 65 mm - max. upper edge overhang: 2 mm - Edge profiles Paper edge: approx. 0.4 mm, chamfer 15 Plastic edge up to 3.0 mm, radius depending on the tool Strip up to 8 mm flush milling (with interchangeable motor on MFA) Machine - Constant workpiece projection from the chain track: 35 mm + edge thickness - max. trimming cross-section 520 mm² - Throughput width: min. 65 mm (with projection of 35 mm) - min. workpiece length in feed direction: 150 mm - Overall height (top edge of chain track): 940 mm - Unit side: on the left in feed direction - Pneumatic connection: approx. 7 - 8 bar Application of release agent, top/bottom Joint milling unit 08.379 and blowing nozzle - with 2 motors, each 4 kW, 9000 RPM, 150 Hz Gluing unit 283.1513 with oil bath gearbox - Adhesive output 0.8 l, 60 mm high, with quick-lock system - can be used for hot melt adhesive or PU adhesive - with single roll / strip magazine, roll diameter 800 mm - with 3 main pressure rollers and 3 counter pressure rollers Trimming unit 08.415 - pneumatically swiveling to 0 or 8 degrees - with 2 motors 660 kW, 400 V, 200 Hz, 12000 RPM - 2 HM trimming saw blades 160 x 3.5 x 22, Z=36 Copy milling unit SKF-L - with 2 motors 180 W, 400 V, 200 Hz, 12000 RPM - and 2 motors 400 W, 400 V, 200 Hz, 12000 RPM - 1 set of DP profile milling cutter I 80x12xHSK25-R, Z = 4, with HSK25 shank - Profile length in the feed direction: max. approx. 50 mm - Workpiece thickness: max. 60 mm - Working speed: max. approx. 20 m/min - Distance between 2 workpieces: min. approx. 400 mm - min. workpiece projection = 35 mm + profile depth Profile trimming blade unit 08.519 - For finishing a top and bottom milled quarter-circle profile Spray cleaning agent Self-adjusting trimming blade unit 08.521 - for removing hot melt adhesive residue from the edge area of the top and bottom of the workpiece Buffing unit 08.617-2 - with an upper and lower motor: 180 W, 50 Hz, 1400 RPM - 2 polishing pads 50 x 160 x 19 mm