Used low loader trailer / lowboy trailers for sale (336)

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Nwsdpfsi Ri Rvsx Aahsb Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Nwedpfx Aaji Riy Ejhob with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: ee3256d63dd23b3ad1bdf9ab0, empty load weight: 10,280 kg, maximum load weight: 13,720 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box on offset recessed in the floor with cover, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the low bed in the tramline area after the offset, sloping towards the entrance, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area 400 mm higher than wheel recess.2nd pair of wheel recesses between the axles in the drop center in the tramline area, slanted towards the entrance, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Wheel well cover can be pulled out from the main frame, with wooden inserts. Distance from main frame beam to beam outside approx. 1280 mm (wheel well area) Widenings extendable to 3,000 mm, foldable on the wheel recess extensions (widening not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed or under the cargo bed if technically possible Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 8 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 2 x at the front on the offset 6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension with lift & lower valve can be operated separately at the front and rear Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Trailer Infocenter, for displaying vehicle data such as axle load (no calibrated scales) and odometer Axle load detection via EBS-Canbus signal, for display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Vehicle - driving stability system Duomatic connection at the front, with connecting cable to the truck, EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Nwsdsi Ri I Nepfx Aaheb Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnoses may occur even though the function is given) 2 white front position lights in LED 2 white/red rear lane departure ligh

Condition: new, machine/vehicle number: 2b58968e34fac93b429a256e9, empty load weight: 5 kg, maximum load weight: 12 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Quarter-shell mudguards in front of 1st axle Spare wheel holder for 1 electric wheel, with wheel mounting kit Spare wheel, same make as basic tires, steel rim Plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Low loader lashing eyes 3 pairs of lashing points, each 10 tons, integrated in the floor at the front 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x according to the rest of the neck area, distributed between them, spacing not greater than 1200 mm 1 x rear bevel 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cableVoltage converter for 12/24 volt operationNote! A 7-pin 12 volt socket is required on the tractor/tractor! (Required in conjunction with electrical voltage converter!) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white/red rear lane departure lights 2 white position lights at the front Additional LED work light(s) at the rear, switched via reversing light Nwsdpfx Aaei Ri Nxjhob 2 x 7-pin interchangeable plugs at the front, with connecting cable1 x 7-pin agricultural plugVoltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Front area steel floor, then with 70 mm softwood floor, steel/ checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 t GG. Customer risk. Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: ebf3f771e96394cd89e56bbb7, overall weight: 11,800 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each 2 pairs of lashing eyes additionally bolted to the floor, 5 tons each in the corners Gear support foot at the front Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Towing device central axle trailer Towing bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension Drum brake axles, manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Nwedpoi Rixrofx Aaheb Front wall / front corner stanchions 25 mm aluminum hollow profile, 400 mm high, Drop sides 25 mm aluminum hollow profile, 400 mm high, foldable and removable Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2,300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with 3 toothed steel rails With gas pressure jack for one-man operation Country of registration/plates Country of registration: Germany 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention! These are archive pictures.

Condition: new, machine/vehicle number: 408ba9a39bbb8087056d6e563, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° / D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Nwsdpfsi Ri Dasx Aahob Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of approval / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized

Condition: new, machine/vehicle number: ede0610378cbe39cc4883251d, empty load weight: 24,000 kg, maximum load weight: 7,550 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Nedpfx Aji Ri Ryjahjwb Chassis low loader trailer Welded steel construction 1st pair of wheel recesses after steel platform recessed in the tramline area, inclined towards the entrance, length at the bottom approx. 1400 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. If machines are to be driven where the overall height is to be checked, we request a technical data sheet for the machine types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer). Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 110 3 pairs of lashing points, 10 tons each, integrated in the floor at the front Incl. 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x to neck area remaining distributed in between Distance not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles which guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Twin steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, incl. Afterwards with 70 mm softwood floor, steel/checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. cannot be achieved. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Incl. with

Condition: new, machine/vehicle number: b50cac2c60a813b0968994fa0, empty load weight: 5,700 kg, maximum load weight: 18,300 kg, overall weight: 24,000 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Rear spray flaps across the entire width Preparation for widening to 3,000 mm (holes in the outer frame and not in the rear slope) Low loader lashing eyes 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 5 x in the drop deck 1 x in the rear slope 12 pairs of lashing holes in the outer frame, each with 5 to. (lashing strap attachment) 5 x crank, 6 x low bed and 1 x in rear slope Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17.5 Fulda Twin steel rims, factory silver Brake system Nwjdpfxsi Ri Ago Aahsb 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, Connecting lines extended by approx. 60 cm without ABS, but with mechanical ALB, then max. 60 km/h approval Electrical system 12 volt, multi-chamber lights, without amber LED lighting at the sides, reflectors at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 7-pin 12 volt plug at the front, with connecting cable, extended by approx. 60 cm 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, illuminated and extendable to 3,000 mm, floor Front offset with steel/ checker plate covering Storage box recessed in drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 5900 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion, for max. 60 km/h registration, towing vehicle LoF, (max. 40 km/h possible in Switzerland) Prepared for two-line license plate holder without contour marking / reflective strips according to ECE R 048, Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 15431365fe5515297a6a9fb05, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each Nwjdpfx Aji Ri A Sjahob 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: d461243f559015adca5bb372c, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Nwodpfx Aei Ri Dloahsb Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco, Knorr or Haldex Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: dd98a7658922be8f2e25bcadb, empty load weight: 2 kg, maximum load weight: 8 kg, overall weight: 10 kg, axle configuration: 2 axles, tire size: 235/75 r 17,5, Further information Chassis central axle trailer low bed Fine-grained steel welded construction Telescopic front support leg Telescopic rear support 2 wheel chocks with holder Mudguards made of sheet steel over both wheels Towing device central axle trailer Tow bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 250 mm Axles + suspension Euro axles of our choice, with angular roller bearings and S-cam brake Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Nwodpfxoi Ri Ebs Aahob Spring-applied parking brake 2 interchangeable clutch heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, TTS bridge Low-lying steel trough, bridge floor made of steel/checker plate covering, steel walls solidly welded to floor Bridge length 4500 mmTub at the front and sides with Load-Lock profile for attaching tensioning straps (8 straps at the front, 12 straps on each side) Note: Slight floor undulation possible due to welding distortion! 2 pairs of lashing eyes, 1 x at the front in the corners of the steel tray and 1 x at the rear in the floor, 5 tons each. 2 additional pairs of lashing eyes in the floor, 5 tons each Drive-on ramps Steel ramps 2 300 mm long, 510 mm wide, can be moved sideways with grab handle on the ramps covered with wood With gas pressure jack for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame RAL 3002 carmine red Hot-dip galvanized drive-on ramps Attention: Archive pictures!

Condition: new, machine/vehicle number: a3b1347da4aa7f31dceb875db, empty load weight: 2 kg, maximum load weight: 9 kg, overall weight: 11 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each Front gear support leg Folding rear support 2 wheel chocks with holder Nwjdpfx Aei Ri Iljaheb Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards Towing device central axle trailer Towbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension BPW drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Front wall / front corner stanchions 25 mm aluminum hollow profile, 320 mm high, Drop sides 25 mm aluminum hollow profile, 320 mm high, foldable and removable Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2 300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with wood With gas pressure jack for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Nodpfx Aji Ri Ddoahewb Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 55d3c5c03e032385649769b1b, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box recessed in Incl. Turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points, 10 tons each, integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Nwsdpfji Ri I Esx Aahob Drawbar with tested 40 mm towing eye Please note! With 40 mm drawbar eye, the maximum permissible total weight of the truck is 18000 kg, otherwise 50 mm drawbar eye required. Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring jack support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany 1 with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame Ral 3002 carmine red 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 6d88bda3a1ee2464a81b34f36, empty load weight: 4 kg, maximum load weight: 13 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction, with slight pretensioning in the middle, turntable with strong ball bearing slewing ring, wheel chocks with holder, quarter-shell mudguards in front of and behind each axle Low loader lashing eyes over front axle: 2 pairs of ring lashing eyes, 5 tons each at the front on offset Lowbed: 4 pairs of lashing eyes on the side of the low bed, 6 tons each 5 pairs of lashing eyes per 5 tons between the side members Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye, mechanically adjustable in length by 6 x 100 mm and lockable (drawbar length 1 700 - 2 300 mm) Axles + suspension BPW drum brake axles, each with an axle load of 10 tons, axle adjuster. Axle endurance brake test to 105 km/h, rear axle can be removed manually. By releasing the air lock and lowering the rear to the ground. Then disconnect the connecting hoses from the rear section, insert the transport bar into one of the rear sockets and unhook the rear by gently pushing it down at the rear and pulling it back at the same time (parking brake released). After loading or unloading, drive up to the rear section and hook it in up to the mark. Then lift the rear section up to driving height and attach the connecting hoses. Confirm the pin lock. (Visually check whether the bolt engages) and check the rear function. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17.5, from leading manufacturers, steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable clutch heads at the front, with connecting lines to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Nwedpfx Aei Ri N Asahsb Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, rotating beacon with holder, switched via parking light (light can be removed), 2 pairs of warning signs, double LED illuminated and extendable to 3,300 mm, removable with plug, 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 x 7-pin agricultural plug, voltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Steel/ checker plate floor on offset, between longitudinal and cross member with perforated plate cover. Axle cover cannot be driven over, widening to 3000 or 3300 mm possible. Operating instructions Please note! A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 tons GG. Customer risk. Special approval required if the overall length of the train exceeds 18 750 mm. Observe country-specific approval regulations. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Observe the BO circle!!! Approval / plates Country of registration: Germany, with Dekra approval and expert opinion (according to §13 EG - FGV), prepared for single-line license plate holder, warning sign according to ECE - 70, contour marking with reflective strips according to ECE R 048 Paintwork Front frame hot-dip galvanized incl. passivation, rear frame RAL9006 silver, drawbar KTL bla

Condition: used, machine/vehicle number: 816b3dfbfa1c7d49b7d052bd6, empty load weight: 2,500 kg, maximum load weight: 8,000 kg, overall weight: 10,500 kg, axle configuration: 2 axles, first registration: 07/2022, tire size: 235/75 r17,5, Year of construction: 2022, Further information Chassis central axle trailer low bed Welded fine-grained steel construction, front gear support foot, telescopic rear support, wheel chocks with bracket, sheet steel mudguards over both wheels Towing device central axle trailer Drawbar with tested 40 mm towing eye, height-adjustable drawbar via spindle, max. adjustment range 250 mm Axles + suspension Euro axles of our choice, with angular roller bearings and S-cam brakes, laser-measured axle/chassis to reduce tire wear and fuel consumption, parabolic suspension with maintenance-free steel/rubber bearings and mechanical axle load compensation (rocker compensation) Brake system 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure warning lights at the rear, 1 x 15-pin plug at the front, with connecting cable, TTS bridge low-lying steel trough, bridge floor made of steel/checker plate covering, steel walls solidly welded to floor, bridge length 5500 mm, trough at front and sides with load-lock profile for tensioning strap attachment (8 pieces at front, 16 pieces on each side) Nedeqmc Raspfx Aahowb Note: Slight floor undulation possible due to welding distortion! Pair of lashing eyes, 1 x at the front in the corners of the steel tray and 1 x at the rear in the floor, 5 tons each. Pair of additional lashing eyes in the floor, 5 tons each Drive-on ramps Steel ramps 2 300 mm long, 510 mm wide, can be moved sideways, with handle on the ramps, covered with wood, with gas pressure jack for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany, with Dekra approval and expert opinion (in accordance with §13 EG - FGV), prepared for single-line license plate holder, contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear

Condition: new, machine/vehicle number: f8fb99947a1c19bc4d63549ff, empty load weight: 6 kg, maximum load weight: 17 kg, overall weight: 24 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 7 pairs of lashing rings at the top and sides of the outer frame, 10 tons each Nwsdpoi Riwfsfx Aahsb 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion with M&S marking Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Coun

Condition: new, machine/vehicle number: f79a9f15e7131d57a512793ab, empty load weight: 8,900 kg, maximum load weight: 15,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Widenings extendable to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical incl. axle load compensation front and rear Axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front offset with steel/ checker plate covering Then with 70 mm softwood floor, steel/checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany With Dekra approval and expert opinion (according to §13 EG - FGV) Nedpei Ri Izefx Aahowb 24/7 service hotline Incl. Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized

Condition: used, machine/vehicle number: 0e87837859aec926e9db10456, empty load weight: 6,200 kg, maximum load weight: 11,800 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 05/2018, tire size: 235/75 r17,5, Year of construction: 2017, Further information Chassis: Welded steel construction, double offset with drop deck in front of and behind axle unit, drop deck slanted towards entrance, turntable with strong ball bearing slewing ring, folding rear support, wheel chocks, side collision protection, quarter-shell mudguards Lashing eyes: above front axle: 2 pairs of ring lashing eyes per 5 tons at the front on the offset drop deck/rear axle: 6 pairs of lashing eyes laterally in the drop deck per 8 tons, 6 pairs of lashing eyes per 5 tons between the side members, pair of stake pockets embedded in the outer frame, inside 70 x 40 mm, or instead of stake pockets, 5 tons ring lashing eyes embedded in the floor. Ring lashing eyes embedded in the floor Drawbar: tested 40 mm drawbar eye Axles: BPW drum brake axles Brake system: 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable front coupling heads Electrical system: 24 volt, multi-chamber lights, amber lighting at the sides, 2 white position lights at the front 2 white/red lane departure lights at the rear, rotating beacon with holder, pair of warning signs illuminated and extendable to 3,000 mm, 2 x 7-pin interchangeable plugs at the front Nsdpfx Aei Ri N Ujahjwb Floor: Front offset with steel / checker plate covering, storage box recessed in drive-over slope to offset, tramline area and in the middle between the beams with steel / checker plate covering, rear slope with 70 mm softwood floor, deep loading area incl. rear slope 5900 mm Drive-on ramps: Hook-in strip for aluminum ramps across the entire width. as U-profile across the entire width Pair of aluminum ramps 800 mm long, approx. 400 mm wide, load capacity per pair 14,000 kg, Storage compartment for ramps between the beams Approval: contour marking with reflective strips to ECE R 048, white at the sides and red at the rear

Condition: used, empty load weight: 4,000 kg, maximum load weight: 5,500 kg, overall weight: 9,500 kg, axle configuration: 2 axles, first registration: 02/2018, next inspection (TÜV): 01/2027, loading space length: 6,043 mm, loading space width: 2,487 mm, loading space height: 2,935 mm, total length: 25,500 mm, total width: 39,000 mm, total height: 77,500 mm, suspension: air, tire size: 205 / 65 R 17,5, color: orange, Year of construction: 2018, front tire size: 205 / 65 R 17,5, rear tire size: Reserverad, emission class: none, Equipment: ABS, ABS, BPW axle manufacturer with drum brakes, Alutec loading ramps, spring-assisted, 3,000 mm, air suspension (air/air), spare wheel, twin tires, sloped rear, 500 mm sideboards, tarpaulin and bow construction, roll-up tarpaulin at the rear, 2 x LED reverse lights, 6 pairs of lashing rings, lifting/lowering function, Duomatic, rotating beacon, upgradable to 11,000 kg gross weight. Nwjdpfxex Ur Uce Aahjb

Condition: used, empty load weight: 8,500 kg, maximum load weight: 31,500 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 01/2012, loading space length: 10,500 mm, loading space width: 2,510 mm, loading space height: 970 mm, suspension: air, tire size: 245/70R17.5, color: white, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 4 axles, turntable, air suspension, ABS (anti-lock braking system), extendable to 3m, lashing rings, hydraulic ramps, rear support, twin tires, wheel recesses. Body: 4-axle low-loader trailer with hydraulic loading ramps, 4x 10t Gigant axles, drum brakes! Ramp length approx. 2850 mm! Nwjdpfx Asxx A H Ijahob Loading height approx. 970 mm! Wheel recess height at the front approx. 600 mm, at the rear approx. 670 mm! The trailer has received a new kingpin! ACCESSORY DETAILS WITHOUT GUARANTEE, subject to changes, prior sale, and errors! - .

Condition: used, first registration: 06/1990, color: other, Year of construction: 1990, OLD LOWLOADER TIRES. Njdexvx Nyepfx Aahswb

Condition: used, first registration: 11/2010, color: other, Year of construction: 2010, GOODYEAR TIRES IN GOOD CONDITION FOR MEGA OR LOWLOADER. Nwodpfx Aaoxvx Ipehsb

Condition: good (used), axle configuration: 3 axles, first registration: 02/2002, total length: 10,050 mm, total width: 2,550 mm, suspension: steel, wheelbase: 6,420 mm, Year of construction: 2002, = Further Information = Axle Configuration Axle Make: BPW Brakes: Drum brakes Suspension: Leaf suspension Front axle: Max. axle load: 000 kg; Steering Rear axle 1: Max. axle load: 000 kg Rear axle 2: Max. axle load: 000 kg Weights Unladen weight: 7,370 kg Payload: 22,630 kg Gross vehicle weight (GVW): 30,000 kg Maintenance, History and Condition APK (Periodic Technical Inspection): valid until 05/2026 Technical condition: good Visual condition: good Identification Registration number: WD-VX-26 Further information Please contact Sales for further information. = Company Information = If you have any questions or suggestions, don't hesitate to contact us. We guarantee a response within 8 hours. Prices are excluding VAT. No rights can be derived from the information provided. Office Phone: MOB: Nederlands - English - Deutsch - Français - Español - Italiano (available on WhatsApp and Viber). MOB: Nederlands (available on WhatsApp and Viber). When paying by bank transfer, the amount must be transferred to our bank account listed below. Always check the payment details as stated on our website. If you have received different information, please contact us. In case of doubt, please call us so we can verify the invoice and/or payment. Bank details: Rabobank Laan van Limburg 2 Nsdpfxsx Tf Igo Aahjwb 4701BP Roosendaal IBAN: NL 89 RABO EORI/VAT/TAX: NL857401B(01) BIC/SWIFT: RABONL2U

Condition: used, maximum load weight: 28,700 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 09/2013, next inspection (TÜV): 09/2026, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available on request. * Excavator bucket well, approx. 2,800 x 770 x 280 mm * 2-piece hydraulic ramps, approx. 2,100 x 2,100 x 700 mm, hydraulically adjustable * Hydraulic rear supports * Hydraulic lifting bed, approx. 4,020 mm long * Partial rubber coating on the loading area and ramps * Drive-over plate for ramps * Extendable loading area * Wabco Smartboard * Air suspension with lifting and lowering function * 2 work lights on the ramps * Hydraulic connections for the towing vehicle * 15-pin socket + ABS * 50 mm towing eye * BPW axles Nedpfsx Tx Eljx Aahowb * Gooseneck with wooden cover * Storage box with lid integrated in the gooseneck