Екоинвест ЕООД

Year of construction: 1997, condition: used, PILOT EXTRUSION SPINNING LINE POLYESTER MAIN PART WAS DESIGNED BY FOURNE IN 1997 FOR DSM TO MAKE TRIALS OF POLYESTER AND POLYAMIDES, MONO & MULTIFILAMENT. >> EXTRUDER DETAILS : MANUFACTURER : FEP POLYMER YOC : 1997 TYPE : EX 25 - 25 D MAX. THROUGHPUT : CA. 7,0 KG/H (PA6), CA. 5,6 KG/H ( PP ) : CA. 8,2 KG/H ( PET ) NOMINAL SCREW DIA : 25 MM SCREW LENGTH : 25 X D SCREW GEOMETRY : SPECIAL 3-ZONE-SCREW MIXING TORPEDO : CHANGEABLE ATTACHED TO SCREW END , CA 3 X D LONG HEATING CAPACITY : CA. 3,2 KW / 4 ZONES DRIVE : CA. 4,5 KW, AS- MOTOR MIT SCHNECKENGETRIEBE ELECTRICALLY HEATED AND REGULATED TO MAX. 350 ° CELSIUS, EQUIPPED WITH 3 TEMPERATURE CONTROL SENSORS, OVER-TEMPERATURE MONITORING, WATER-COOLED FEED ZONE, REMOVABLE ISOLATION AND BASIC FRAME, INCLUDING INERT GAS IN THE INLET PIPE, EQUIPPED FOR THE SUBSEQUENT RECEPTION OF A TORQUE CLUTCH ON THE GEARBOX END >>> SPINBEAM & MELT PIPE : ELECTRICALLY HEATED SPINBEAM DESIGN : FOR 1 MONFIL OR 2 MULTIFILAMENT THREADLINES SPINPUMPS : 1 = 2 X 2.4CC , 1 = 1 X 2.4 CC , 1 = 1 X 0.6 CC SPINNERETTES : 42 / 59 / 72 >>> Hfsdpfx Acozl Hz Nohei QUENCH CABINET : FEP Polymertechnik Gmbh YOC : 1995 TYPE : CROSSFLOW Plant Nr. : 7.1396 >>> WINDER : BARMAG TYPE : SW4S Auftragsnr : 10/0428 YOC : 1988 >>> DRAW – STAND : EDMUND ERDMANN GMBH TYPE : DRAWMOD 02/380-3/5/6 LM YOC : 1995 COM. NR : 13/2492 CONTROLS COMPUTER : EDMUND ERDMANN YOC : 1995 FABR. NR : 132492 >>> PREHEATING OVEN : HERAEAUS Gmbh Type : WU6100 , 500C , 3 Nipe, 400 V 11.4 A, 5.4 kW YOC : 1997 FABR. NR : 97/11055 >>> HOIST IN EXTRUDER AREA : HEBEZEUGFABRIK GMBH, YOC : 1998, CAPACITY : 0,7 TONS LIFTING HEIGHT : 0,8 M

Condition: refurbished (used), functionality: fully functional, screw diameter: 172 mm, rotational speed (max.): 49 rpm, In recent years, over €420,000 have been invested in new components and factory refurbishments! Further technical details can be found in the attached documentation. TECHNICAL DETAILS Screw diameter: 172 mm Screw speed: 4.9 - 49 rpm Max. torque: 17,500 Nm MACHINE DETAILS Main motor: 216 kW Gearbox manufacturer: P.I.V Coperion DSE 180 TECHNICAL DETAILS Power: 7.5 kW Output torque: 280 Nm Degassing chamber: 1 Screw housing bore: Ø 181.5 mm Screw diameter: 180 mm Pressure build-up (axial pressure on the screw shaft): max. 25 bar EQUIPMENT Double screw degassing unit Coperion DSE 180, year 2021 Main gearbox P.I.V, year 2002, factory refurbished in 2021, unused Main gearbox P.I.V, year 1986, factory refurbished in 2016, in operation 2021 - 2023 Main motors Siemens, 212 kW, year 2002, factory refurbished in 2020, unused Main motors Siemens, 212 kW, year 1986, factory refurbished in 2015, in operation 2020 - 2023 Screw housings, 16 various, new and used Screw shafts, 2 x approx. 4,600 mm Hjdpfx Acjzl A N Nshefi Supports Screw tips Thrust discs Note: The electrical and control technology as well as the screw segments are not included in the scope of delivery.

Year of construction: 1996, condition: ready for operation (used), A Sandern vacuum calibration and cooling tank is offered. Max. pipe diameter: 125mm, tank length: 6000mm, number of chambers: 2. Dimensions X/Y/Z: 6500mm/1000mm/1500mm, weight: 1500kg. Inspection by appointment possible. Hodpfx Aozli U Sochefi

Year of construction: 1989, condition: good (used), Werner ZSK 58/32 D twin-screw extruder Year: 1989 110 kW motor Hfodpfxezktrrs Achoi

Year of construction: 2012, condition: used, This Macchi 3-layer blown film co-extrusion line is designed for the production of high-quality polyethylene films with outputs of up to 800 kg/h. The line processes LDPE, LLDPE, MLDPE, and HDPE and is suitable for manufacturing collation shrink film, gusseted shrouds, stretch hood film, tubing, and sheeting. Materials to be processed: LLDPE/LDPE/LLD/HDPE Extruders: 65 mm + 80 mm + 65 mm Infrared heaters 3 pcs plate filters Head: 3-layer blown film die head TE5303-IBC-350/500 Die diameter: 350 and 400 mm IBC Die gap: 1.8 mm Output: Up to 800 kg/hour, depending on the material formulation Air ring: Dual-flow air ring, carbon fiber Take-off: Take-off unit, 2400 mm wide Oscillating nip rollers Motorized side gusseting Rewinder: Double winder, fully automatic back-to-back rewinder Winder, fully automatic roll change Reel diameter up to 800 mm Winding width 2350 mm Accessories: Tower Web guide, E&L Gravimetric weight control system, Piovan/Doteco Component blender, Shini Dosing units, Doteco Automatic thickness control, Kundig K-Design profile gauge control system Hsdpfx Acjzkru Eohsfi Calibrating basket Corona treater, Martignoni Air shafts, 8 pcs

Year of construction: 1988, condition: used, functionality: fully functional, Year: 1988 Material: LDPE/HDPE Winder width: 1100 mm, double winder Hfodjzi Urwjpfx Achsi Die diameter: 150, 100, 80, 50 Screw diameter: 60 Additional equipment: corona treatment + gravimetric system Maximum machine capacity: 90 kg The machine is in very good condition and can be seen in operation!

Condition: used, in perfect condition, with a brand new housing (replaced just last year). Hodpfxeziz Swo Achsfi

Condition: used, Dr. Wiesner Type: INTEGRA DDV -1...1 bar Item Description: Dr. Wiesner Integra leak testing system The classic – for all common testing methods The leak testing system for industrial leak and flow tests with a fully graphic color display up to three independent test circuits can be operated 255 test programs can be stored automatic process optimization autoTune (option) Communication via flexibly interchangeable bus coupling modules freely programmable fixture control freely programmable special test sequences The device is suitable for tests using the relative and differential pressure methods with overpressure. Special versions: none Technical data: Electrical supply: 110 ... 230V~; 50 ... 60Hz (connection via power cable to plug XO) Pneumatic: clean and dry compressed air max. 7 bar (to connection P) Pressure range: 0 ... 1000 mbar, electronically controlled Measuring ranges Hedpfxsziiv De Achsfi Relative pressure: 0 ... 1000 mbar Differential pressure: +20 mbar Resolution: 0.1 Pa Internal volume: 13 cm³ test circuit 15.0 cm³ reference circuit Electrical interfaces: 3x serial RS232 (COM1; COM2; COM3) 1x digital I/O (X1) Pneumatic: Connection for test object (Test) Connection for reference circuit (Ref.) Housing Degree of protection: IP40 Dimensions: 450x185x380mm (WxHxD) Weight approx. 15.5kg Condition: used (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Year of construction: 2005, condition: ready for operation (used), Screw diameter: 114mm, max. PVC throughput: 600 kg/h, max. screw speed: 20/min, number of heating zones for molds: 12, motor power: 76 kW, rated voltage: 3x 415V AC, rated current: 353A, rated power: 218kW, weight: 7.1t, operating hours: approx. 90,000h. Screws: Geometry designed for PVC profiles, water-cooled, cylinders: nitrided, air-cooled, equipped with a new PLC control system, vacuum pump, and power inverter for the main motor. An on-site inspection is possible. Hsdpozh Nibofx Achjfi

Year of construction: 2003, operating hours: 65,470 h, condition: refurbished (used), functionality: fully functional, machine/vehicle number: Titan 68R-APC/ 2 68F-60-40-1100-UT, Titan 68R-APC/2 68F-60-40-1100-UT with tungsten carbide cylinder and screw (designed for WPC-HDPE base) Very good feeding behavior and good processing. Screw modification for optimal use, including in the recycling sector. The system has been completely overhauled and is ready for use. Feeder optionally available. SIHI vacuum pump. Hjdozh Ednepfx Achefi For throughputs up to 400 kg/h. For highly filled compounds, approximately 180 kg/h. 4-zone heating.

Year of construction: 2026, condition: new, functionality: fully functional, machine/vehicle number: 053 389 601, Offered for sale is an extrusion tool for PVC, used in the manufacture of PVC pipes. Pipe diameter range, min.: Ø63 mm Pipe diameter range, max.: Ø160 mm Output: approx. 750 kg/h Design: Mandrel carrier system designed for PVC melts, Hfjdezhuqkspfx Achji completely made of 1.2316 Flow contour polished Equipped with cylinder heaters and thermocouple M14x1.5, type “J” Includes 3 m connection cable, without plug connector for the extruder Technical data: 230V, 50Hz for max. 3600W per zone, 16A Number of heating zones: 6 Two copies of the operating manual, in German or English, are included in the scope of supply.

Year of construction: 2026, condition: new, functionality: fully functional, machine/vehicle number: 066 404 601, An extrusion tool for the production of PE or PP pipes is offered. Pipe diameter range (min.): Ø90 mm Pipe diameter range (max.): Ø250 mm Output: approx. 1100 kg/h Design: Spiral distributor system, completely made of 42CrMo4 Hfedpfszhnd Rjx Achsi Flow contour polished Equipped with cylinder heaters and M14x1.5 type “J” thermocouples Incl. 3 m connection cable, without plug connector for the extruder Technical data: 230V, 50Hz for max. 3600W per zone, 16A Number of heating zones: 7 2 copies of the operating manual in German or English are included in the scope of delivery. The offer includes the following items: - Basic tool PO G 250 - Sheathing package for a max. 10% outer layer - Flex nozzle insert for Ø250/180, with this nozzle insert, all dimensions from Ø250 to Ø180 can be produced in SDR17 + SDR11. - Tool mounting carriage, swiveling by 90° - Internal cooling for oil or water in the spiral distributor - Pipes for a pipe head air cooling system are installed in the tool.

Year of construction: 2017, condition: ready for operation (used), Granulation line, regranulation extruder, Yei machine I. PE/PP waste regranulation line, model: YDN-120 Material: PP/PE Maximum capacity: PP: 550 kg/h PE: 650 kg/h Installed power: 420 kW Power consumption during operation: approx. 250 kW Water consumption: approx. 25 l/min Required water pressure: 3 kg/cm² 1) Extruder Designed for double degassing Hjdpfx Acezhm Ihshsfi Double-stage gearbox Screw diameter: 120 mm Made of SACM 645 steel, chrome-plated and hardened L/D ratio: 32:1 Rotation speed range: 0-130 rpm Heater power consumption on the barrel: 51 kW Number of heating zones on the barrel: 5 Barrel cooling: 1/8 HP x 5 fans Motor: 175 HP, controlled by a frequency inverter 2) Screen changer, 15 HP Filter area: 90,639 mm² x 2 Equipped with a pressure sensor with alarm. In case of excessive pressure, the machine will automatically shut down. One temperature control zone. 3) Knife system for granulating at the extruder head Number of knives: 4 pcs Temperature control: 1 zone Heating power: 3.5 kW 2 heads for PE 4) Water cooling system Motor: 5 HP, controlled by a frequency inverter 5) Shredding and pre-compacting drum Vertical type with temperature sensor Motor power: 150 HP, controlled by a frequency inverter Equipped with 12 rotary knives and 17 stationary knives Mill diameter: 1300 mm Blower: 7 1/2 HP Continuous water cooling device 6) Belt conveyor Dimensions: 4950 mm (length) x 670 mm (width) Motor: 2 HP 7) Vibrating dryer Water pump: 5 HP x 1 Vibration motor: 1/4 HP x 4 pcs Water tank dimensions: 3615 mm x 700 mm x 471 mm 8) Regranulate silo (with a centrifugal blower of 7.5 HP with a transport pipe) 9) Control panel Indicates the operating status of all major electrical devices The machine is equipped with a double cylinder screen changer, allowing for screen changes without stopping the machine. The line is designed in a compact way, which saves usable space. The device requires maintaining the cooling water temperature: 25-35°C Equipment: Enlarged drum to 1300 mm with 150 HP motor Second degassing port on the first screw with a vacuum pump Metal detector 5 HP centrifuge Second "cascade" plasticizing module (150 mm screw) with filter with a single degassing port and vacuum pump double-stage gearbox Parameters of the second plasticizing module Screw diameter: 150 mm Made of SACM 645 steel, chrome-plated and hardened L/D ratio: 20:1 Rotation speed range: 0-130 rpm Number of heating zones on the barrel: 2 Motor: AC 75 HP, controlled by a frequency inverter Control panel Hydraulic screen changer x 2 cylinders Additional equipment Increased filter area on the first screen changer: Standard: diameter 140 mm x W126 mm = 55,389 mm² x 2 After enlargement: diameter 204 mm x W141.5 mm = 90,639 mm² x 2 The delivery includes additional cooling for the control cabinets Static mixer with a connecting pipe for homogenization and uniformization of the mass.

Year of construction: 1999, condition: used, The system is not just a simple recycling extruder; it is a complete plastic recycling line consisting of: * Heysohn PAR 108 agglomerator/compactor (1993) * Heysohn extruder with degassing * Material feed and metering * Discharge/conveying system * Documentation available * Multi-zone heating (at least 9 heating zones visible) * Vacuum degassing * 60 kW main drive * RAVIS 2 modular control system * Machine is evidently still fully assembled The control panel shows the following handwritten notes: * Extruder type: presumably PAR 108 * Diameter: 130 mm * Extruder output: approx. 345 kg/h * Motor power: 135 HP The system appears to have been used for processing film and plastic regrind into granules. Battenfeld BFX2-130-25V plastic extruder – year of manufacture 1999 Hfsdezhl R Ispfx Achji For sale is a plastic extruder from Battenfeld Extrusionstechnik GmbH, type BFX2-130-25V, year of manufacture 1999. The system consists of an extruder, material feed with hopper, drive unit, and conveying system. The machine comes from an industrial plant and is in assembled condition. Manufacturer: Battenfeld Extrusionstechnik GmbH Type: BFX2-130-25V Year of manufacture: 1999 Operating voltage: 400 V / 50 Hz Weight: approx. 9,500 kg

Year of construction: 2026, condition: new, functionality: fully functional, Conical laboratory single-screw extruder EX 60/30 The extruder is designed for processing light, free-flowing granular materials. Due to its screw size, the extruder is suitable for laboratory and testing applications. The nitrided screw with a conical inlet section is fed with materials via a hopper, which then flow through the large inlet opening into the cylinder. Subsequently, the raw materials are compressed in the cylindrical screw section and discharged through a die. A direct drive with an upstream thrust bearing forms the drive train. Ceramic heating bands also allow for high processing temperatures. A shielding cooling system is installed between the material hopper and the first heating zone. Optionally, we also offer the following machines: The strands are passed through a water bath with a stainless steel tank to the strand granulator. A screen changer can also be offered as an option between the extruder and the die. Screw speed 150 Hsdpfxszhamwo Achjfi Current 29.5A CEE-63A

Year of construction: 2008, condition: used, functionality: fully functional, machine/vehicle number: 2801816/010, We offer this used Cincinnati Talos 75-30G, manufactured in 2008. Manufacturer: Cincinnati Model: Talos 75-30G Hfsdpfxjzg Uuye Achji Year of manufacture: 2008 Condition: used If you have any questions or require further information, please do not hesitate to send us a message or call us.

Year of construction: 2006, condition: ready for operation (used), A complete Battenfeld compact extrusion line for the production of PVC profiles is available. 1) Twin-screw extruder Battenfeld MBEX 2-50-16 V, year of manufacture: 2006, output capacity: 15kg-60kg/h, screw diameter: 52mm, screw length: 16×D, barrel zones: 4, barrel cooling zones: 3, adapter zones: 1, die heating zones: 9, control system: BMCtouch. Including dry vacuum pump, pressure measuring points, clamping flange, water-air separator, blow-off device, mounting elements and hopper cover. 2) Calibration table Battenfeld KP 125 V 2/4m, mounting frame length: 4100mm, mounting rail width: 320mm, longitudinal adjustment: 500mm, transverse adjustment: +/-15mm. 3) Speck vacuum system, pumps: 2, motor power: 2×4kW, operating pressure: 200mbar, max. air capacity: 2×140m³/h. 4) Battenfeld RP 125 SE caterpillar haul-off, passage height: 100mm, contact length: 1100mm, pad width: 160mm, haul-off speed: 15m/min, max. haul-off force: 7kN. 5) Battenfeld SP 63 E underfloor saw, max. cross-section capacity X/Y: 200mm/300mm, sawing accuracy: +/-0.5mm. Overall line dimensions X/Y/Z: approx. 12000mm/1200mm/2000mm, weight: approx. 4500kg, operating hours: approx. 319h. Including chip extraction. The line touchscreen is defective (nothing is visible), however, the line can be operated using an external monitor, mouse and keyboard. Documentation available. An on-site inspection is possible. Hedpozg Iqhefx Achsfi

Year of construction: 2021, condition: like new (used), functionality: fully functional, machine/vehicle number: LE-2104-133, For Sale: Labtech LE30-30/C 3D Filament Extrusion Line We are offering for sale a high-quality 3D filament extrusion line manufactured by Labtech Engineering Co., Ltd., a well-known producer of laboratory and production extrusion equipment. Technical Specifications Manufacturer: Labtech Engineering Co., Ltd. Model: LE30-30/C Year of Manufacture: 2021 Power Supply: 400 V Phase: 3 Installed Power: 16.7 kW CE Certified Price: EUR 45,000 Condition The machine is in excellent condition, has been professionally maintained, and is ready for immediate production use. Included in the Sale Complete 3D filament extrusion line Additional spare barrel 25mm Additional spare screw 25mm/24D Optional Equipment Available for Purchase Laser diameter gauge Hodpezgwlzefx Achjfi Material dryer Material feeding/dosing system This extrusion line is suitable for the production of high-quality 3D printing filaments and offers reliable operation with consistent output quality. Additional photos, technical details, and machine inspections can be provided upon request. Location: Ivanka pri Nitre

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1990, machine/vehicle number: E2018, total length: 7,000 mm, total width: 3,500 mm, total height: 6,000 mm, Very well-maintained machine in good working condition. Capacity up to 100 kg/h. Screw diameter 60 mm. Hedpfozgc Ihex Achsfi Head diameter 160 mm. New, additional set of screws and cylinder included.

Condition: used, functionality: fully functional, Grinding Machine Weber MSG 460 2 2 This universal Weber knife grinder has been specifically designed for sharpening circular knives. These knives require precisely sharpened edges, optimal cutting angles, and accurate cutting edge geometry. The machine ensures this with consistent, repeatable accuracy throughout the entire service life of the cutting tools. The short setup time, combined with the non-driven grinding wheels, makes this an efficient machine for small to medium-sized meat processing companies. Specifications: Gbe Uc Ijzf Adtezu Rsp Hodpszf Adtjfx Achofi - Knife diameter working range: 420–460 mm - Grinding angle adjustment: 15°–35° - Voltage: 380 V (3 + N, 50 Hz) - Power: 0.18 kW - Weight: 91 kg - Machine dimensions (W × D × H): 570 × 670 × 1510 mm

Condition: reconditioned (used), Overall condition: Very good Hsdpfx Aszfzg Tjchofi Recent maintenance: The cylinder (barrel) was replaced last year.

Year of construction: 1995, condition: ready for operation (used), functionality: fully functional, power: 52 kW (70.70 HP), screw conveyor diameter: 49 mm, machine/vehicle number: DE27566, TECHNICAL DETAILS Capacity: 150 – 250 kg/h Screw diameter: 2 x Ø 49.7 mm L/D ratio: 32D Hodpfxjzd Scpj Achsfi MACHINE DETAILS Motor power: 52 kW (DC) Control system: analog, contactor-controlled system EQUIPMENT Synchronous motor Degassing Vacuum pump

Year of construction: 2009, condition: excellent (used), functionality: fully functional, Film up to 1400 cm wide With ParsControl Gravimetric Hjdpfx Acozd Ai Hohefi AB line

Year of construction: 2010, condition: excellent (used), 414 USED Bakery oven, trolley, rotary, 60x80 cm. Year of manufacture: 2010. Hsdpfjzdra Isx Achofi EXTERNAL DIMENSIONS (in cm): - W: 155, - L: 175 (with hood 237) - H: 263. The USED device is available to verify in our warehouse (36-068 Bachórz, Poland). Paid options available: renovation / transport / assembly / commissioning of the device. The price is a net price. Our languages: ENGLISH, FRENCH, GERMAN, UKRAINIAN.

Year of construction: 2001, condition: good (used), For sale: an industrial twin-screw extruder, Werner & Pfleiderer ZSK 133, now known under the Coperion brand. This machine is designed for processing and compounding plastic materials, especially PP granules, polyolefins, masterbatches, filled, and modified materials. The extruder was manufactured in 2001 and purchased used in 2015 in working condition. However, it has not been used in our production since the purchase. It has been idle since then and is being sold due to lack of use. Key specifications: capacity up to 4 t/h, main electric motor 1100 kW, voltage 690 V, frequency 50 Hz, motor speed 1492 rpm, screw speed up to 400 rpm, maximum pressure 200 bar, heating power 137 kW, 6 heating zones, dimensions 3535 × 900 × 500 mm. Hfsdozc I Igspfx Achji The extruder includes a melt pump, an underwater granulator with a die and a set of knives, a cooling system for a water bath, an oil unit with electric heaters for heating the granulation die, and hydraulic units for operating and locking the shears. Suitable for factories involved in compounding, PP granule production, masterbatch production, regranulation, and processing of large volumes of plastic.