Used Schaffer 5680 T for sale (13,120)

Condition: new, overall weight: 41,000 kg, empty load weight: 9,800 kg, maximum load weight: 31,200 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: dc46d2e1cd272305b99fb3160, Further information Vehicle consisting of: Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions Dkslq Roi Ri Hcjrtrel 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit 1st pair of wheel recesses after gooseneck recessed in the low bed of the tramline area, slanted towards the entrance. Length at bottom approx. 1600 mm, depth of wheel recesses approx. 260 mm. Note! Frame in main beam area 260 mm higher than wheel recess. 2nd pair of wheel recesses between A and B axle. Bottom length approx. 350 mm, depth approx. 260 mm. Note! Frame in main carrier area 260 mm higher than wheel recess. If wheel loaders are to be driven and the overall height is to be checked, we request a technical data sheet for the wheel loader types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses are required by the customer). Wheel recess cover can be pulled out from the main frame, with wooden inserts. Widenings extendable to 3,000 mm (not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 2 pairs of ring lashing eyes, 5 tons each at the front on the gooseneck 11 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x on gooseneck9 x in low loader bed distributed first lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, or instead of stake pockets 5 to. Ring lashing eyes embedded in the floor Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm, removable with plug Floor Gooseneck with steel / checker plate covering Storage box embedded in drive-over slope to gooseneck Then with 70 mm softwood floor, in the wheel recesses underneath and in the wheel

Condition: used, machine/vehicle number: 053560166, sweeping width:72 cm Capacity:1450 Watt total power requirement:1,27 kW weight of the machine ca.:0,225 t dimensions of the machine ca.:0,55 x 1,25 x 1,15 m Dolq Rjcxxt Sjrtrjkl

Condition: new, Year of construction: 2024, machine/vehicle number: MASM13T, Stock machine available immediately New Kaeser SM 13 T - 10 bar screw compressor with integrated refrigeration dryer with ECO-Drain (level-controlled condensate drain) Dolq Rjix Akpertrekl Control: SIGMA CONTROL 2 Year: 2024 Pressure: 10 bars Rated power: 7,5 kW Delivery quantity at 10 bar: 1.08 m³/min Sound level: 65 dB(A) Compressed air outlet: 3/4" Dimensions length x width x height: 630 x 1090 x 1100 mm Weight: 315 kg Operating hours: 0 hrs Visit our store. We always have a wide range of new and used compressors in stock!

Condition: ready for operation (used), Functionality: fully functional, power: 33.1 kW (45.00 HP), overall weight: 2,150 kg, fuel type: diesel, color: red, axle configuration: 4x4, empty load weight: 1,575 kg, fuel: diesel, driver cabin: day cab, gearing type: hydrostat, Year of construction: 2015, operating hours: 3,906 h, Equipment: additional headlights, air conditioning, all wheel drive, differential lock, hydraulics, Large area mower: Dkolovitkcoq Rrtrjl Gianni Ferrari Turbo 4 T Cruiser K EL Year of construction 2015 3,906 operating hours 45PS Kubota diesel engine All-wheel drive Dif. lock Hydrostat Rear wheel steering Full cab Air conditioning / heating Stationary throttle Hinged doors Lighting High dump (max. loading height 225cm) Mower with 2 sickles and 150cm mulching kit Additional hydraulics 360cm x 125cm x 200cm (lxwxh) Unladen weight: 1,575kg; permissible GG: 2,150kg Municipal vehicle from 1st hand Receive all new vehicles by email - subscribe to our NEWSLETTER! Errors and typing errors possible, subject to prior sale!

Condition: reconditioned (used), Year of construction: 1997, Functionality: fully functional, Schleicher 3 unit drilling machine after lignum renovation. Machine equipped with upper units 3 pieces .Pneumatic pressure .Working realized by forcing the button unit the rest of the automatic .Choice of units possible each one or all .Speed and depth of drilling the possibility of setting .Machine after major repair .New electricity and driver .Net price vat invoice warranty one year .The machine can be additionally equipped with rulers bumpers pressures and drilling heads of any spacing . Djlq Rrtst Ndznorekl

Condition: new, Baking chamber with bottom made of refractory stone Interior insulation made of mineral rock wool Interior lighting for each chamber Upper and lower heat separately adjustable 85°- 455°C (Model PF 5050 DE3, PF 4040 DE3 with 3 thermostats) Analogic temperature display (optional version T) (not for PF 5050 DE4/3/E, PF 4040 DE4/3/E) Separate On/Off switch for each baking chamber (not for PF 5050 DE4/3/E, PF 4040 DE4/3/E) Front side made of stainless steel, body made of sheet steel Vent chimney Model: PF 7070 E-T Dkjlq Rrouu Ez Totrel Capacity: Ø 34 cm (4) Internal dimensions: 70 x 70 x 15 cm External dimensions: 97 x 89 x 43 cm Electric power: 5 kW, 3NAC and 400 V Weight: 82 kg

Condition: new, overall weight: 41,000 kg, empty load weight: 8,900 kg, maximum load weight: 32,100 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: 2428b2018baf171e60fef6740, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions, 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Mudguards in front of 1st axle and rear of each axle with anti-spray, according to EC Dkslq Rroi Ri E Rotrol Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 2 pairs of ring lashing eyes, 5 tons each at the front on gooseneck 11 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 2 x on gooseneck 9 x distributed in the low loading area First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17.5 brand of the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 LED rotating beacon with holder, switched via parking light (light can be removed) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck with sheet steel covering Storage box recessed in drive-over slope to gooseneck Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 9 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK socket NW 10/3, without connecting hoses Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! Special permit required if total train weight exceeds 40 tons! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) When applying for a special pe

Condition: as good as new (ex-display), Year of construction: 2024, Horizontal Bending press Zopf - model T 200 with automatic backgauge - programable backgauge 900 mm with - year of construction 2023 - demo model - length of stroke 185 mm - weight 500 kg Delq Rrsgrydbstrskl Bending capacity flat material mild steel 200x12 mm (with special tooling) with punch radius 5 mm and die V = 100 mm Touch screen with programming of the stroke and backgauge demo model

Condition: used, Functionality: fully functional, Year of construction: 2018, operating hours: 7,771 h, load capacity: 3,000 kg, lifting height: 3,655 mm, free lift: 150 mm, mast type: duplex, construction height: 2,450 mm, power: 39 kW (53.03 HP), fork length: 1,200 mm, engine type: 4-Zyl. VW, drive type: Treibgas, LPG forklift Load center: 500 Mast type: Duplex Condition: Ready for use and fully functional Dkjlq Rrstzg D Notrel Technical condition: good Front tires type: Superelastic Rear tires type: Superelastic Description: Sideshift, 3rd valve, rear working lights, front working lights, heating, full cab, LED,

Condition: new, Year of construction: 2024, operating hours: 55 h, Exhibit available immediately: Dkslqsunliqe Rrtrel Kaeser SK 25 T - 8 bar screw compressor with integrated cold dryer with Controller SIGMA CONTROL 2 Year 2024 Operating hour: 55 h Pressure: 8 bar Nominal power: 15 kW Delivery rate: 2.51m³ / min Sound level: 67 dB (A) Compressed air outlet: 1 " Dimensions length x width x height: 750 x 1240 x 1260 mm Weight: 395 kg Visit our store. We always have a large selection of new and used compressors in stock!

Year of construction: 2021, Condition: new, modular drilling machine 8 automatic units Do: Go mad Model: Wu 3g 2C 3T Description: Producer GOMAD Benh7jc8jp Year of production 2021 Machine category Modular drilling machine location Gorzów Wlkp. Conditions of delivery Djlq Rjhara Dertrokl OWN COLLECTION Shipping costs Client protection Start type to be agreed Description Remarks MODULAR MODULAR DRILL, TRAILER SLIDING BLADE, HALF-ADAPTATION WITH AIR PEDAL DRILL EQUIPMENT Year: 2021 THE NEW VERSATILE DRILLING MACHINE

Condition: as good as new (ex-display), Balcancar el.rope hoist 1 tonn capacity. Was installed one time on the rail, but never used. Doleld S Nwsq Rrtrokl

Condition: new, overall weight: 41,000 kg, empty load weight: 11,800 kg, maximum load weight: 29,200 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: 364a8214fd0c4afa2b936c7db, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions (not in conjunction with forced steering) 24 t. 2-speed support winch, single-side operation, with semicircular lower section and straight connecting plate, with thrust compensation Folding rear support Wheel chocks with holder Aluminum side collision protection Spray flaps in front of 1st axle and rear of each axle with anti-spray, according to EC Stainless steel storage box, w=600/h=400/t=500 mm, with polished door, lockable Dkjlq Rrtei Ri E Ujrsl Lifting table to gooseneck, approx. 3000 mm long, can be raised hydraulically to pass over the gooseneck, with mechanical lock when raised. Operation with radio remote control Electric cable winch, 24 volt, tractive force 8165 kg, mounted in the middle at the very front of the loading area, standing on the gooseneck, in stainless steel box with door (if technically possible, exact testing still required), operation with radio remote control, cable length 35 m x approx. 10 mm, with roller cable window and removable guide rollers on gooseneck and rear inclination. Low loader lashing eyes Gooseneck:5 pairs of lashing eyes recessed in the outer frame, each with 5 to.2 pairs of lashing eyes in the middle, each with 5 to.1 pair of lashing mushrooms on the top and outside of the outer frame recessed in the neck slope, each with 10 tisch:4 pairs of lashing eyes recessed in the outer frame, each with 5 to.4 pairs of lashing eyes in the middle, each with 5 to. Pair of lashing eyes in the middle, each 5 to.1 pair of lashing mushrooms at the top and outside of the outer frame, each 10 fbett:4 pairs of lashing eyes in the outer frame, each 5 to.5 pairs of lashing eyes in the middle, each 5 to.4 pairs of lashing mushrooms at the top and outside of the outer frame, each 10 to. Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lift & lower valve, with hold function for lowering + auto-reset function Wheels and tires 235 / 75 R 17,5 according to manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear Lights completely in LED design (note! with certain towing vehicles, misdiagnosis may occur, although the function is given) 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Additional LED work light(s) at the rear, switched via reversing light LED rotating beacon with holder, switched via parking light (light can be removed) Pair of warning signs, double LED illuminated and extendable to 3,000 mm, removable with plug Floor Gooseneck covered with Mega Gri

Condition: good (used), Year of construction: 2007, operating hours: 24,287 h, Functionality: fully functional, machine/vehicle number: H-H5022, travel distance X-axis: 1,270 mm, travel distance Y-axis: 660 mm, travel distance Z-axis: 610 mm, controller model: Ultimax, spindle speed (max.): 12,000 rpm, number of slots in tool magazine: 40, TECHNICAL DETAILS Control system: Hurco Ultimax X travel: 1,270 mm Y travel: 660 mm Z travel: 610 mm Speed: 12,000 rpm Power: 15 kW Torque: 238 Nm Tool magazine Tool magazine: 40 stations Tool holder: SK40 Tool diameter: 75 mm Tool length: 300 mm Tool weight: 10 kg Table and clamping Clamping surface: 1,500 x 660 mm T-slots: 6x 18 x 1000 mm Table load (max.): 1,300 kg Spindle to table distance: 150 - 760 mm Rapid traverse Rapid traverse X: 30 m/min Rapid traverse Y: 30 m/min Rapid traverse Z: 20 m/min MACHINE DETAILS Dimensions: 3,250 x 2,350 x 2,950 mm Weight: 9 tons EQUIPMENT - Chip conveyor - IKZ system with filter and high pressure - Tool measurement: laser, BLUM - Interface measuring probe prepared - Electronic handwheel Djlq Rrtsu Dairerokl - Spindle cooler

Condition: used, Functionality: fully functional, Year of construction: 2015, operating hours: 4,423 h, load capacity: 2,000 kg, lifting height: 4,620 mm, free lift: 1,500 mm, mast type: triplex, construction height: 2,120 mm, power: 28 kW (38.07 HP), engine type: 4-Zyl. VW, drive type: Treibgas, LPG forklift Load center: 500 Mast type: Triplex Transmission: Hydrostat Condition: Ready for use and fully functional Technical condition: Very good Front tires type: Superelastic Rear tires type: Superelastic Description: Sideshift, tine adjuster, Dolq Rjui U Hujrtrjkl 3rd valve, 4th valve, rear working lights, front working lights, semi-cab, LED,

Year of construction: 2012, Condition: used, Control system with VIET IPC CONTROL color display Terminal with the possibility of memorizing program positions Automatic adjustment in real time of all the parameters necessary for processing Automatic positioning of the working thickness with gauge TM version with moving heads and fixed table (suitable to be placed in line) Feed speed from 3 to 16 mt / min Working width 1350 mm Abrasive belt length 7400 mm Dkjlq Rrsgnz N Netrsl Working height 3 - 160 mm No. 3 working groups: * Adjustable transversal sanding unit with electronic pads T42 ET 150x7400 with 15kW motor with inverter * Adjustable transversal sanding unit with electronic pads T42 ET 150x7400 with 15kW motor with inverter * Panel cleaning group in output Conveyor belt with 3kW motor with inverter Rubber conveyor belt perforated by depression Depressor for conveyor belt

Condition: like new (used), Operating conditions: The heavy-duty trailer is designed for use on level, paved roads in internal traffic. Combined journeys: Dkolq Rrsuf Snystrjl The trailer components are not designed (without trailer coupling) for combined journeys with several trailers. Payload: 60 t at 6 km/h and uniform loading (surface load) of the loading area between the axles. Point or strip loads are only permitted after notification. Base frame: Sturdy welded construction made of sectional steel Loading area: Size approx. 10000 x 3000 mm, loading height approx. 1105 mm, loading area cover with softwood planks, all-round recessed edge protection Steering: All-wheel steering on 4 pendulum axles, drawbar can be raised, removed and repositioned from front to rear, suspension height on towing vehicle approx. 650 mm (other suspension heights are only permitted after notification), drawbar eye to DIN 74054 dm 40 mm, tie rods with adjustable ball joint heads, diagonal or drawbars adjustable and fitted with low-maintenance spherical bearings, drawbar drop safety device to UVV. Chassis: 4 steered swing axles, 2 steered axle lines to achieve an even load on the wheels, wheels with elastic solid rubber tires approx. 559 x 406 mm, wheel hubs with tapered roller bearings and permanent grease lubrication. Paint finish: Top coat RAL 5002 ultramarine blue For hire or sale EU-wide.

Condition: used, IDC000109 - Obel Pedersen RF feed band press type T20V - Press length 2500 mm width 600 mm - HF generator T20 V and water cooling Dkolevgddhoq Rrtrsl

Condition: new, overall weight: 57,000 kg, empty load weight: 12,800 kg, maximum load weight: 44,200 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: df15479123e15bcf265d560e1, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Telescoping Central tubular frame in neatly welded telescopic frame sections that run into each other. Extendable by max. 6,000 mm and can be arranged approx. every 1,000 mmPayload/point load is reduced when extended! Locking mechanism with mechanical bolt lock With sliding table Low loader lashing eyes 2 pairs of ring lashing eyes each 5to at the front on gooseneck 11 pairs of lashing mushrooms at the top and at the side embedded in the outer frame each 10to 2 x on gooseneck 9 x in low-loader bed distributed first lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between the lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Dkelqji Ri Hno Rrtrjl 3 pairs of additional hinged lashing eyes embedded in the low bed, 10 to each1x at the start of the low bed, 1x in front of the 1st axle and 1x behind the 3rd axle Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Last 2 axles self-steering, with automatic reversing lock via reversing light and manual locking function via hand button on the vehicle. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17.5 Fulda tires Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable sockets at the front, without connecting cable Floor Gooseneck with steel / checker plate covering Storage box recessed in drive-over slope to gooseneck Then with 70 mm softwood floor, steel / checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Drop sides 25 mm hollow aluminum profile, 400 mm high, front and side on gooseneck, pluggable Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle Hydraulic connection w

Condition: new, Functionality: fully functional, wheelbase: 3,500 mm, Year of construction: 2025, Day cabin, sun visor, fog lights in the bumper, Comfort air seat, double passenger seat, Air conditioning, PX-7 engine, 290 hp, ZF manual transmission, 9 gears, Exhaust brake, Differential lock, Rear tyre, PTO on the gearbox, DN Cranes 15,000 crane, 5 extensions with radio control, 4 m three-way tipper with TR5 H60 aluminium sides, Payload: 4950 kg, Available for immediate delivery Djlq Rovq Rr Tjrtrekl

Condition: new, Year of construction: 2024, Model: C3T Working Area: 3048mm*1524mm Laser Output Power: 6000w/3000w/2000w/1500w Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Max. linkage speed: 100m/min Max. acceleration: 1G 1. Double Fast Exchange Tables Fast exchange of two tables greatly improves efficiency. Chain-drive system has better rigidity and higher accuracy, saving feeding time. 2. Tenon-and-mortise Welded Bed Use Chinese traditional Tenon-and-mortise structure to provide stronger bearing capacity. Solder joint fixing and structural bearing ensure long-standing operation stability. Welded structure improves shock absorption effect, lowering deviation caused by shock, and offering more accurate cutting. 3. Double Automatic Centering Electric Chucks Dkelq Rsg D Nz Rjrtrol Double electric chucks with automatic centering function are easy to operate and require little maintenance. Brand new motor gives accurate control. Modular chuck components are independently developed and can be quickly replaced. 4. Automatic focusing function of laser head By setting perforation focal length and cutting focal length respectively, the cutting is more accurate. Suitable for multiple focal lengths, and focal position will be automatically adjusted based on thickness of different sheets.

Condition: used, Year of construction: 2015, Numeric Control Startouch Control System Panel height mm. 60 Edges in PVC/Abs rolls mm. 3 Solid wood in strips mm. 6 Feed speed up to 11 m/min Working height adjustable electronically by C.N. Panel support guide with adjustment Side roller conveyor with idle wheels for panel support Anti-adhesive group Adjustable two-motor rectifier unit Reel holder plate Gluing group for EVA glue Edge pressure unit on straight profiles with adjustable pressure rollers Trimming unit with 2 motors with automatic inclination adjustment Gleaning unit electronically adjustable by C.N. Multifunction rounding unit (edner + rounder) adjustable by C.N. Edge scraper unit Dkelqetxtzks Rrtrjl Glue scraper unit Oscillating brush group

Condition: like new (used), Operating conditions: The heavy-duty trailer is designed for use on level, paved roads in internal traffic. Combined journeys: Djlq Rreuf Rw Tjtrskl The trailer components are not designed (without trailer coupling) for combined journeys with several trailers. Payload: 60 t at 6 km/h and uniform loading (surface load) of the loading area between the axles. Point or strip loads are only permitted after notification. Base frame: Sturdy welded construction made of sectional steel Loading area: Size approx. 6000 x 2500 mm, loading height approx. 1012 mm, loading area cover with softwood planks, all-round recessed edge protection Steering: All-wheel steering on 4 pendulum axles, drawbar can be raised, removed and repositioned from front to rear, suspension height on towing vehicle approx. 650 mm (other suspension heights are only permitted after notification), drawbar eye to DIN 74054 dm 40 mm, tie rods with adjustable ball joint heads, diagonal or drawbars adjustable and fitted with low-maintenance spherical bearings, drawbar drop safety device to UVV (accident prevention regulations) Chassis: 4 steered swing axles, 2 steered axle lines to achieve an even load on the wheels, wheels with elastic solid rubber tires approx. 559 x 406 mm, wheel hubs with tapered roller bearings and permanent grease lubrication. Paint finish: Top coat RAL 5002 ultramarine blue Additional equipment: - Optional: dual-circuit air brake system acting on 4 wheels, gradient < 4%. Separate parking brake via spring-loaded brake cylinder, also acting on 4 wheels. - 2 lashing eyes or crane eyes made of round steel welded horizontally into the outer beams on both long sides, only use the crane eyes when the trailer is not loaded - Turning radius inside approx. 2100 mm - Outside turning radius approx. 5500 mm - Drawbar approx. 1500 mm long Rental or sale EU-wide.

Condition: like new (used), Operating conditions: The trailer is designed for use on level and paved roads in internal traffic. Towing vehicle with type designation: unknown Transported goods: unknown Combined journeys: The trailer components are not designed (without trailer coupling) for combined journeys with several trailers. Payload: 40t at 6 km/h and uniform loading (surface load) of the loading area between the axles. Point or strip loads are only permitted after notification. Base frame: Sturdy welded construction made of sectional steel Loading area: Size approx. 5000 x 2400 mm, loading height 930 mm, loading area cover with wooden planks, all-round edge protection Steering: All-wheel steering on 4 pendulum axles, drawbar can be raised, removed and repositioned from front to rear, suspension height on towing vehicle approx. 670 mm (other suspension heights are only permitted after notification), drawbar eye to DIN 74054 dm 40 mm, tie rods with adjustable ball joint heads, diagonal or drawbars adjustable and fitted with low-maintenance spherical bearings, drawbar drop safety device to UVV (accident prevention regulations) Chassis: 4 steered swing axles (2 steered axle lines) to achieve an even load on the wheels, wheels with elastic solid rubber tires approx. 559 x 305mm, wheel hubs with tapered roller bearings and permanent grease lubrication. Djlsuf Rwyeq Rrtrjkl Paint finish: Top coat RAL 5002 ultramarine blue Additional equipment: 2 lashing rods in each of the long sides For hire or sale EU-wide.

Condition: excellent (used), Operating conditions: The industrial trailer is designed for use on level, paved roads in internal traffic. Combined journeys: The trailer components are not designed (without trailer coupling) for combined journeys with several trailers. Payload: The industrial trailer can be used to move loads up to a maximum of 25 t at 6 km/h and uniform loading (surface load) of the loading area between the axles. Point or strip loads are only permitted after notification. Base frame: The base frame of the industrial trailer consists of a stable welded construction made of sectional steel. Loading area: The size is approx. 6000 x 2400 mm. The loading height is approx. 750 mm. The loading area is covered with softwood planks and edged with all-round edge protection. Djlqeuf Rt Us Rrtrskl Steering: Four-wheel Ackermann steering, drawbar can be raised, removed and repositioned from front to rear, attachment height on towing vehicle approx. 285 - 775 mm (other attachment heights are only permitted after notification), towing eye in accordance with DIN 74054, dm 40 mm, drawbar safety catch in accordance with UVV Chassis: The two axles of the industrial trailer are steered. Elastic solid rubber tires approx. 559 x 356 mm, wheel hubs with tapered roller bearings and permanent grease lubrication Paint finish: Top coat RAL 5002 ultramarine blue Additional equipment: 2 lashing rods made of round steel are welded vertically into the outer beams on each of the two long sides of the industrial trailer. For hire or sale throughout the EU.