Used Tabe Agb-375 for sale (1,622)

Condition: used, Cardan shaft, cardan shaft, universal joint -Cardan shaft: universal joint, unused -Type / order no .: 21001375 402027/201 7610AVA09 -Shaft: Ø 24 mm -Measurements: see photos -Number: 4x universal joint available -Price per piece -Dimensions: 102/46/H50 mm -Weight: 0,6 kg / pc. Duehjhf Dzpjxzuf Ist

Condition: new, table diameter 340 mm table load 160 horizontal kg. table load 100 vertikal kg. turning speeds 0,6 - 6,0 U/min swivelling range 0 - 90 Grad bore 60,0 mm motor 230 Volt weight of the machine ca. 56 kg. range L-W-H 385 x 340 x 375 mm Furnishing: - The table can be adjusted at an angle of 0 to 90 degrees tilt and jam - Start / stop via a location-independent foot switch. - Direction of rotation can be selected right / left. - Adjustable rotation time - The turntable has a 60 mm hollow shaft - The turntable has a diameter of 340 mm. The surface is chrome-plated for Protection against welding spatter. - The table speed is adjustable from 0.6 - 6 rpm. - The control of the welding machine via the turntable control is possible. - The ground contact transmits 300 A / 100%. - The turntable and the control are separate. - HF protected. - COM 1800 control with lap welding - Operating instructions in German Functions COM 1800 control: - Right/left rotation - Infinitely variable speed control - Welding torch on/off - Overlap welding adjustable - Controller for rotation time (2-stroke / 4-stroke) - Speed display Dehxzufsuxfrbj Ieut

Condition: used, Functionality: fully functional, Year of construction: 2013, operating hours: 4,855 h, load capacity: 2,000 kg, lifting height: 800 mm, fuel type: electric, mast type: standard, construction height: 1,400 mm, fork length: 1,150 mm, drive type: Elektro, Low lift order picker Mast type: Standard Technical condition: normal Front tires type: Bandages Rear tires type: Bandages Battery Volt: 24V Battery Ah: 375Ah Battery year of construction: 2018 Dushxzueukricsf Ist

Condition: good (used), Year of construction: 2010, Functionality: fully functional, overall weight: 375 kg, load capacity: 3 kg, For sale is a stand-alone handling machine of the Engel brand and type ERC 13/12-F The handling unit is ready for immediate use and fully functional after assembly Technical data Year of construction: 2010 Max. handling weight: 3.5 kg X-stroke: 400 mm Dshxzufovgc Sks Ijut Y-stroke: 1,000 mm Z-stroke: 2,240 mm Y-axis: Single stroke B-axis drive: Pneumatic B-axis torque: 5 Nm Servo axes: 3 Pneumatic axes: 2 Compressed air circuits: 2 Valve positions: 6 required DI(UEK): 8 Stand height: 375 mm Connection data: 3*400 V /50HZ/16 A Rated current: 10,000 A Shelf height 900-1200 mm (depending on installation height) On request, transportation and loading can be arranged at extra cost. can be organized throughout Europe. Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: used, Year of construction: 2003, turning diameter max. 420 mm turning length 1090 mm control FANUC Serie 18i-TB Dshxzuoucgyljf Isut turning spindle Durchlass 108 mm 250 / 315 turning speed range 0-3750 U/min Feed speed 18/24 m/min. workpiece 12 quill stroke 100 mm diameter of quill 110 mm taper MK 4 number of driven tools 12 mm turning speeds 3000 U/min 22 nm coolant tank 140 l total power requirement 22/18,5 kW weight of the machine ca. 6500 KG dimensions of the machine ca. m

Year of construction: 1988, Condition: used, x-travel 500 mm y-travel 400 mm z-travel 400 mm Dujhxzueqpl Uqef Iet digital readout Heidenhain 3 Achsen spindle taper SK 40 spindle turning speed range 50 - 2500 U/min table-size 650 x 375 mm weight of the machine ca. 1,5 t dimensions ca. mm

Condition: used, Cardan shaft, cardan shaft, universal joint -Cardan shaft: universal joint, unused -Type / order no .: 21001375 402027/201 7610AVA10 Djhxzuohf Dz Eof Isut -Shaft: Ø 36 mm -Measurements: see photos -Number: 15x universal joint available -Price per piece -Dimensions: 120/62 / H56 mm -Weight: 1.1 kg / pc.

Condition: used, Year of construction: 1996, pressure 130 t chamfer lenght 3060 mm distance between columns 2690 mm column arm 410 mm stroke 215 mm dayligth 385 mm ajustment speed 200 mm/sec working feed 1-10 mm/sec return speed 135 mm/sec table width 120 mm table height 1050 mm tiltable up to +/- 10 mm Number of working hours 53.820 h Duohxzuet Raflsf Iot compressed air 5.0 - 7.0 bar oil volume 250 l operating pressure 340 bar voltage 400 V total power requirement 16.0 KVA weight of the machine ca. 11250 kg range L-W-H 3640 x 2210 x 2375 mm - in checked condition - machine video - youtube.com/watch?v=23IbxRaZ2KA Equipment: - CNC electro-hydraulic press brake - including DELEM CNC control model DA 65 * swiveling control panel, front left * 2D graphic programming & product display * tool & program library * including new TFT-LCD industrial monitor - CNC controlled axes: Y1 + Y2 / X / R - CNC electro-motor / controlled back stop (X axis) - CNC electro-motor / controlled height adjustment (R axis) - manual adjustment of the 2x stop fingers, from the front (Z axes) - manual adjustment of the die displacement, from the front (I axis) - WILA manual table crowning, including analog value display - TRUMPF hydraulic upper tool clamp - TRUMPF manual lower tool clamp - 1x freely movable 2 hand / foot control - Safety device at the rear (sliding door) - Safety device at the side (swinging door) - Original operating instructions + CE declaration + circuit diagram

Condition: used, machine/vehicle number: W4X132J02187, Year of construction: 2018, load capacity: 2,000 kg, construction height: 1,530 mm, fork length: 2,345 mm, drive type: Elektro, Low lift truck Fahrgestellnummer: W4X132J02187 Condition: Reconditioned without warranty Technical condition: good Battery Volt: 24V Battery Ah: 375Ah Dehxeuhxfwozuf Ieut Battery year of construction: 2018 Description: Linde N20 No.: R0271 Year of construction: 2018 The device is visually in very good and technically in good condition. Charger on request. Fast and uncomplicated transport possible by arrangement! The advertisement only serves to identify the device! A detailed description of the condition and possible equipment will be provided individually on request! Subject to errors and prior sale, sale only to tradespeople. All sales of used goods are subject to the exclusion of warranty or guarantee. If you have not found the forklift you are looking for, please contact us. We have a large selection of other equipment on site.

Year of construction: 1993, Condition: used, Cutting depth 220 mm Dshxzufsd N Slgj Iout weight of the machine ca. 375 kg 4 new blades

Year of construction: 1978, Condition: used, pressure 2000 /1000* t distance between columns 2650 mm stroke 500 mm column travel -side 500 x 1000 mm diameter of piston 710 mm number of pistons 2 distance between table / ram 1000 mm operating pressure 130 / 230 bar dayligth 800 mm table length 2500 mm table width 1600 mm table height 250 mm draw back pressure 500 kN Duehxzsd Ih Ncjuf Iot number of T-slots 8 turning speeds 1500 U/min rapid speed 120 - 140 mm/min closing speed max. 120 - 140 mm/sec. return of plunger by small single cylinders 100 - 110 mm/sec hydraulical ram locking cutting sound absorber 300 t die cushion capacity 200 t die cushion stroke 250 mm speed of die cushion 100 mm/sec frequency 50 Hz voltage 380 V quantity of oil 2000 l total power requirement 93 kW weight of the machine ca. 100 t dimensions of the machine ca. 5000 x 2500 x 7200 mm transport measurements ca. 6500 x 3750 x 2190 mm 1991 assembly of a die cushion, pressure reduction to 1000 tons reason: tools were only constructed to 1000 tons press has run in a perfect condition until disassembly. It was replaced by a press line. important for UVV: press has a hydraulic ram locking!

Condition: used, Forklift motor with gear, electric motor, direct current motor, traction motor, drive motor -Voltage: 23 volts -Power: 3 kW -Speed: 1705 rpm -Drive motor for: Steinbock forklifts -Dimensions: 375/230/H200 mm Dujhxzujdp Npijf Iot -Weight: 25 kg

Condition: new, pressure 400 t chamfer lenght 4100 mm distance between columns 3550 mm column arm 510 mm ram stroke speed 110 mm/sec work speed 8.4 mm/sec return speed 130 mm/sec work stroke 375 mm dayligth 650 mm table height 1000 mm table width 240 mm back stop - adjustable max. 800 mm oil volume 400 ltr. voltage 400 Volt total power requirement 30.0 kW weight 26409 kg range L-W-H 5450 x 2650 x 3470 mm ----- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection ----- Furnishing: Duohxzjt D Hvqeuf Ijt - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot tool Roleri 135.85.R08, "System A" - with additional crowning of the upper wedge - Universal die block - LEUZE light barrier behind d. machine - BOSCH / HOERBIGER hydr. Components - SIEMENS - electrical system - FIESSLER AKAS laser protection device in front of the machine (including FPSC) - 2 front support arms with SLIDING system (plain bearings) - Double foot operation - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes Special equipment including: - electrical central lubrication

Condition: used, machine/vehicle number: W41173G00992, Year of construction: 2016, operating hours: 1,460 h, load capacity: 1,400 kg, lifting height: 2,930 mm, free lift: 1,500 mm, mast type: duplex, construction height: 1,950 mm, fork length: 1,200 mm, drive type: Elektro, net weight: 1,355 kg, High lift truck Dehxouhw Tyjzuf Ieut Fahrgestellnummer: W41173G00992 Mast type: Duplex Technical condition: good Battery Volt: 24V Battery Ah: 375Ah Battery year of construction: 2016 Description: Linde L 14 No: M0484 Year of construction: 2016 Operating hours: 1,460 The device is visually and technically in a used condition. Subject to errors and prior sale. If you have not found your truck, please contact us. We still have a large selection of other devices on site.

Condition: used, Face plate, face plate chuck, four-jaw chuck, facing chuck -Chuck size: Ø 400 mm -Cone size: 6 Dujhxzufjd E Tfwj Ijt -Short taper mount for: bayonet disc -Short taper mount: Ø 106.375 mm -Hole circle: Ø 133.4 mm -Through hole: Ø 90 mm -Weight: 51 kg

Condition: new, pressure 320 t chamfer lenght 4100 mm distance between columns 3600 mm column arm 410 mm ram stroke speed 140 mm/sec work speed 10.5 mm/sec return speed 150 mm/sec Duohst D Hu Tsxzuf Ijt work stroke 375 mm dayligth 650 mm table height 900 mm table width 220 mm oil volume 400 ltr. voltage 400 Volt total power requirement 30.0 kW weight 22064 kg Dimensions (HxWxD) 5350 x 2450 x 3150 mm ----- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection ----- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot tool Roleri 135.85.R08, "System A" - with additional crowning of the upper wedge - Universal die block - LEUZE light barrier behind d. machine - BOSCH / HOERBIGER hydr. Components - SIEMENS - electrical system - FIESSLER AKAS laser protection device in front of the machine (including FPSC) - 2 front support arms with SLIDING system (plain bearings) - Double foot operation - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes Special equipment including: - electrical central lubrication

Condition: used, machine/vehicle number: W41173G00945, Year of construction: 2016, operating hours: 5,073 h, load capacity: 1,400 kg, lifting height: 2,930 mm, mast type: standard, construction height: 1,920 mm, fork length: 1,200 mm, drive type: Elektro, net weight: 1,370 kg, High lift truck Fahrgestellnummer: W41173G00945 Mast type: Standard Condition: Ready for use and fully functional Technical condition: good Battery Volt: 24V Battery Ah: 375Ah Battery year of construction: 2016 Description: Linde L 14 AP No.: R0014 Year of construction: 2016 Operating hours: 5,073 The device is visually and technically in good condition. Subject to errors and prior sale. If you have not found your truck, please contact us. We have a large selection of other trucks on site. Dujhxzufeuhw Tgo Ijt

Condition: used, Gear motor, electric motor -Speed: 30 rpm -Power: 0.45 kW Djhxzsct Tyqouf Ieut -Construction: hollow shaft angle -Diameter hollow shaft: Ø 24 mm -Protection class: IP 54 -Brake -Number: 1x geared motors available -Price: per piece -Dimensions: 375/160/H275 mm -Weight: 12.5 kg

Condition: new, pressure 320 t chamfer lenght 3100 mm distance between columns 2600 mm column arm 410 mm ram stroke speed 140 mm/sec work speed 10.5 mm/sec return speed 150 mm/sec work stroke 375 mm dayligth 650 mm table height 900 mm table width 240 mm oil volume 400 ltr. voltage 400 Volt total power requirement 30.0 kW weight 17082 kg Dimensions (HxWxD) 4550 x 2450 x 3200 mm ----- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection ----- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot tool Roleri 135.85.R08, "System A" - with additional crowning of the upper wedge - Universal die block - LEUZE light barrier behind d. machine - BOSCH / HOERBIGER hydr. Components - SIEMENS - electrical system - FIESSLER AKAS laser protection device in front of the machine (including FPSC) - 2 front support arms with SLIDING system (plain bearings) - Double foot operation Djhxzufet D Huyo Iout - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes Special equipment including: - electrical central lubrication

Condition: new, pressure 100 t chamfer lenght 2600 mm Djhxzjt D Hi Rjuf Iout distance between columns 2200 mm column arm 410 mm ram stroke speed 200 mm/sec work speed 9.5 mm/sec return speed 155 mm/sec work stroke 275 mm dayligth 530 mm table height 900 mm table width 90.0 mm oil volume 150 ltr. voltage 400 Volt total power requirement 7.5 kW weight 6850 kg range L-W-H 3750 x 1950 x 2800 mm ----- Press brake with special equipment * increased installation height * increased cylinder stroke * as well as increased bending beam speeds ----- Furnishing: - DELEM CNC control model DA 53T (touchscreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135.85-R08, system "A" with quick-change clamp - Additional crowning device in the tool holder of the upper tool - 4V universal die block M 460 R with die shoe 60 mm holder - BOSCH / HOERBIGER hydr. Components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protective device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "sliding system", with T-slot and tilting cam - 1x double foot control - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes

Condition: new, pressure 80.0 t chamfer lenght 2600 mm distance between columns 2200 mm column arm 250 mm ram stroke speed 90.0 mm/sec work speed 7.5 mm/min return speed 60.0 mm/sec work stroke 160 mm dayligth 380 mm table height 900 mm oil volume 150 ltr. voltage 400 Volt weight 5227 kg range L-W-H 3750 x 1950 x 2400 mm Furnishing: Dujhxjt D Hiqszuf Ijt - DELEM - CNC control model DA-58T - controlled axes: Y1 - Y2 and X - AKAS laser in front of the machine - manual crowning - Upper tool, deer foot - Lower tool, die block with 4Vs - SICK light barrier behind the machine - 2 front support arms - SIEMENS - electrical system - BOSCH / HOERBIGER hydraulic system - CE mark / declaration of conformity - Operating manual: machine and control - Safety manual: press brakes

Condition: used, Year of construction: 1987, sheet width 3050 mm plate thickness 6.0 mm thickness at "Niro-steel" 4.0 mm cutting angle 0.5 - 3.0 ° down holder 18 Stück no. of strokes 9 / 14 Hub/min back stop - adjustable max. 750 mm Duohxzjtrzd Nsuf Ist Control konv. engine output 10.0 kW weight 4800 kg range L-W-H 3750 x 1600 x 2450 mm maintained condition (!!) Furnishing: - electro-hydraulic / slide-guided sheet metal shears - front control panel, left - easy to use - with electro-hydraulic cutting angle adjustment - with manual cutting gap adjustment, from the rear - electro-motorized back gauge 10-750 mm - with analogue position display + handwheel for fine adjustment - 1x robust side stop - 1x freely movable foot switch - front finger/encroachment protection - 2x EMERGENCY stop buttons at the front - User manual (PDF)

Condition: new, cutting diameter 305 mm capacity 90 degrees: flat 350 x 200 mm capacity 90 degrees: square 260 mm capacity 45 degrees: flat 230 x 200 mm capacity 45 degrees: round 250 mm capacity 45 degrees: square 230 mm capacity 60 degrees: flat 170 x 100 mm capacity 60 degrees: square 155 mm capacity 60 degrees: round 175 mm turning speed range: 18 – 110 m/min dimensions of saw-band 3.375 x 27 x 0,90 mm work height max. 880 mm Control total power requirement 1,5 / 1,8 kW weight of the machine ca. 840 kg dimensions of the machine ca. 1.900 x 1.850 x 2000 mm Furnishing : - miter left 45 ° automatic operation - miter left 60 ° semi-automatic operation (cuts without programming) - Material height sensor (automatic cut start detection) - Frame and gear from a single source - very quiet cut and very low vibration Dshjixmnljxzuf Iout - Chip tray can be removed (disinfection) - Shockproof and ergonomic control panel with oil-proof EPDM cover - Easy access to the saw, material and feed unit - Foldable safety cover - Fine adjustment of the feed rate - semi-automatic cut BERG SCHMID CNC control: - Possibility to enter various parameters such as number of pieces and material length, automatic calculation of the cutting channel - for 10 different sawing programs, with 99 sub-programs - for different lengths and quantities e.g. 1x cutting program with various cut lengths - Incremental feed with automatic length compensation - Adjustable for cut lengths from 2 mm to 9,999 mm, remaining piece length 170 mm - Single stroke - feed slide 500 mm Info from the manufacturer: When installing this saw in the network with Residual current circuit breaker (FI) should this universal current sensitive and not below 300 mA be executed.

Condition: new, table diameter 500 mm table load 300 horizontal kg. table load 150 vertikal kg. swivelling range 0 - 90 Grad turning speeds 0,2 - 2,5 U/min bore 90,0 mm table height ~ 650 mm mm motor 230 Volt weight of the machine ca. 90,0 kg. range L-W-H 385 x 340 x 375 mm Furnishing: - The table can be tilted and clamped at an angle of 0 ° to 90 ° - manual tilting - Start / stop via location-independent foot switch - Direction of rotation can be selected right / left - Adjustable rotation time - The control of the welding machine via control - 350 amp ground connection Dujhxsixm Nmjzuf Iet Scope of delivery: - control (integrated) - foot switch

Condition: new, bore capacity in steel (diameter) 35,0 mm bore capacity in cast iron 40,0 mm throat 320 mm threading M 24 in Stahl morse taper 4 MK bore stroke 160 mm turning speeds 65 - 3250 U/min table: 500 x 420 mm throat 320 mm weight 375 kg range L-W-H 600 x 870 x 2.170 mm Furnishing: - Infinitely variable speed, ideal for - Set the desired cutting speed. - Automatic tool ejector and thread cutting device as standard - Electromechanical drilling feed, adjustable from 0.1 - 0.3 mm / rev - Solid gray cast iron table with rotating and swiveling support surface - T-slots in the machine base enable high workpieces to be clamped - Guaranteed concentricity 0.02 mm, measured in the quill - Hardened and ground gears ensure smooth running - Adjustable drilling depth stop with an easily readable scale Scope of delivery: - Key chuck 1 - 13 mm / B 16 Duehxod N Dfrszuf Iot - Drill chuck arbor MK 4 / B 16 - Reducing sleeve MT 4/3, MT 4/2 - coolant device - Thread cutting device - Electromagnetic spindle feed - Automatic tool ejector - LED machine light - First filling with Shell Tellus 46 - Digital speed display - Height-adjustable protective cover