Used Gesan Dps 100 for sale (40,196)

Condition: good (used), Manufacturer: Systema Type: H100 Colji D Dkden Sx T Sjrb

Condition: good (used), Year of construction: 2002, machine/vehicle number: 02022-00, Hand shears, foot pedal, retractable sheet support The machine will be repaired, tested, and cleaned by a specialist and will then be fully functional. A test run will be performed. Sheet width/working Sheet width: 6020 mm Steel sheet thickness: 1.0 mm Aluminum sheet thickness: 1.5 mm Stainless steel sheet thickness: 0.6 mm Without backgauge Thrust: 1000 mm Color: blue Crsln Sxev Szuhe T Ssb Total power requirement: 16 A Space requirement: 6800 x 1600 x 1700 mm Insertion depth: 1000 mm Machine weight: 2400 kg With roller shears Number of uprights: 4 Opening width: 200 mm Bending angle: 145 degrees

Year of construction: 2021, Condition: as good as new (ex-display), Rental Unit A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant The Alpine Ultraplex UPZ is a universal impact mill that can be fitted with a variety of easily interchangeable grinding tolls to achieve different results, such as pin disc, beater disc or pendulum beater. Certain grinding tools can operate together with different grinding tracks, sieves or a combination of both to achieve the desired fineness. This allows the same machine to process many different products such as fibrous roots or spices to plastics, granulated chemical or mineral products. Materials up to approx. 3 Mohs can be processed on the UPZ. The 100 UPZ is the perfect mill for the laboratory, research and development of new materials or even small scale production. Thanks to the easy mill’s door opening, that doesn´t require disassemble of other system parts nor use of tools, grinding tools exchange or revision is very quick. It is fitted with a security device that prevents the opening of the machine while in operation. Crjln Sxsf H Azgj T Seb Motor power: 1.5 kW Construction material: stainless steel

Condition: ready for operation (used), Percussion Mill MFL Type R-CI 100-100 Csln Sx Tswbbivo Sorb Feed opening 1020 x 760 mm Power: 90 kW E-Motor Weight 9 Tons

Year of construction: 2010, Condition: refurbished (used), Bizerba TU100 summing table after renovation Crelnji Drwqe Sx T Seb

Condition: ready for operation (used), Platinum thickness: 0.5-4.5mm, component height: top max. 16mm, bottom max. 30mm, components: Chip, MELF, SOT, SOIC, TSOP, PLCC, QFP, BGA, LCC, µBGA etc., Incremental axes X: 0.001mm, Y: 0.001mm, Z: 0.02mm, theta: 0.045°, connected load: 2500W, operating temperature: 18-30°C, control: microprocessor control with CAN interface, operated on PC with Windows® 7, vision system: ESI CorePlace®, automatic board alignment, complete component identification, inspection of solder pads, pin positions, component position, BGA ball count etc., weight: 700kg. On-site inspection is possible. Crjln Sjwb E Shsx T Sjb

Condition: used, Year of construction: 2024, pressure 100 t stroke 300 mm table surface area 1070 x 260 mm column travel between the guideways 1070 mm ajustment speed 8.0 mm/sec working feed 5.0 mm/sec return speed 10.0 mm/sec oil volume 90.0 l engine output 5.5 kW weight of the machine ca. 1500 kg. dimensions of the machine ca. 2050 x 1000 x 2200 mm Croln Sxeixmz Ho T Sjb Display machine from 2024 With only approximately 2 operating hours Like new condition Special price upon request Furnishing: - Robust electro-hydraulic workshop press, with fixed cylinder - Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more. - Robust welded steel construction for high demands - Table height adjustment via piston rod * including round steel chain and 2x locking bolts * Piston rod with metric socket - 1x set of V-block prism supports - Manometer for pressure display - simply constructed hand control with: * 1x delivery speed * 1x working speed * 1x retreat speed - Piston can be stopped in any position - Hydraulic tank mounted on the side - Operation manual

Condition: good (used), Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams, swivel cylinders -Hydraulic cylinder: double-acting stroke 100 mm -Piston rod: Ø 25 mm Cjlnjv Nhc Ts Sx T Ssrb -Holes: Ø 25 mm / Distance: retracted 355 mm -Dimensions: Ø 77 x 420 mm -Weight: 6.9 kg

Year of construction: 2008, Condition: refurbished (used), Functionality: fully functional, Fully refurbished Hosokawa Alpine UPZ 100 used system by Alpine Originals. Technical details Design: Non Pressure Shock Resistant (NPSR), non ATEX, not suitable for inert operation (N2) Material of construction: stainless steel Without wear protection Celn Sxoq Rv E Do T Ssrb Batch operation, for a few kilos normally (product dependent) Scope of supply 100 UPZ system in large table fitted with pins (other grinding tools of choice could be offered for an additional price), small feeding hopper with a dosing screw, filter and barrel to collect the fines, blower and piping. Includes a relay control panel. This small size system with an universall mill UPZ 100 can be used for the production of small batches as well as for R&D purposes. Thanks to the different grinding accessories it can be adapted to different tasks and target fineness. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mill. It is used to grind soft dry materials. This micronizer is perfect to pulverize different coarse products down to a finer powder and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetics, recycling, etc. This grinder can be used for the pre-cut of different materials. It is able to process coarse products up to approx. 3 Mohs´ hardness by reaching medium to fine particles with end-product fineness values between d97 150 to 850 microns (µm) top size (product dependent) at the lowest possible energy consumption. The turbo mill can reach this wide final product range thanks to a variety of easily interchangeable grinding tools such as pin disc, plate beater, beater disc or pendulum beater. Certain grinding tools can operate together with different grinding tracks (liners), sieves or a combination of both, to achieve the desired fineness. This allows the same machine to process many different products such as fibrous roots or spices to plastics, granulated chemicals or mineral products. The comminution takes place inside the grinding chamber where the rotor plate fitted with grinding tools impacts and projects the particles against the grinding track or sieve (if fitted) reducing their size. The process gas then transports the fines to the mill outlet towards the next stage, normally the filter. Thanks to the required process air volume, reduced temperature increase during grinding is to be expected compared to other granulation and crushing technologies. Adjusting the final particle size distribution can be easily done by changing different parameters, such as the speed of the grinding rotor or disc, the type of grinding tool and liner, air volume, feeding rate, etc. A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery

Year of construction: 2023, Condition: new, SEMIX Mobile 100S4 is equipped with 3000/2000 liters capacity Concrete mixers which can be a single shaft, twin shaft, or planetary type mixers. In SEMIX Concrete Mixers NiHard4 or Hardox 450 wearings are used according to the Concrete recipe’s sillicium ratio. Cjln Sogay Nyox T Sorb All SEMIX Aggregate Storage hoppers are bent trapezoidal shape for having an extra strength. Aggregate storage hoppers can be fed by wheeled loaders with a single ramp. Aggregates are weighed in the weighing conveyor which transfers aggregates to the transfer conveyor. Having two separate conveyors providing accuracy in weighing and performance for reaching higher Concrete outputs. All SEMIX Concrete Batching Plants are being controlled by a SCADA system with a Schneider PLC integrated. Users can follow all used materials and integrate it their CRM system. SEMIX's engineering team can intervene in the Automation system online to provide service.

Year of construction: 2008, operating hours: 85,654 h, Condition: repair required (used), Functionality: not functional, A defective 17m³ climate chamber is for sale. The compressor of the pre-cooling stage is probably defective (see photo, red X), a detailed inspection has not been carried out. The system is being sold defective. Colnovmwyce Sx T Ssrb Temperature range: -60°C to + 100°C Humidity range: 10 to 95% r.H Dew point range: +5°C to +89°C The system can be inspected by prior appointment. Deployment takes place at ground level through sufficiently large doors, here assistance can be offered, otherwise the buyer is responsible for deployment and removal.

Condition: ready for operation (used), Cycle time: 1.16s/QFP with Area CCD camera, 0. 85s/chip with Closed Loop Electromechanical Alignment, optimal placement rate: 3125 on IPC 9850 with Area SCC & LCC cameras, 4200 on IPC 9850 with CLEA, nominal placement rate: 2500-3500cph (components per hour), processable component types: 0201-Chip, MELF, SOT, SOIC, TSOP, TNT, PLCC, QFP, BGA, µBGA, LCC, field size: 42x42mm, fine pitch: Up to 0.4mm (16 mil), Tool change station: 12 nozzle positions, Heads: single gantry with two independently controlled pipettes, Assembly accuracy (X/Y) 3σ: 50µ with Area CCD camera,100µ with Closed Loop Electromechanical Alignment, PCB dimensions (X/Y): 30-330x30-450mm, PCB alignment: fiducial detection by ESI CorrectPlace® incl. Teach-in for drill holes or unusual contours, loading and alignment time: approx. 2.8s, number of axes: 2, length: 1700mm, width: 1500mm, height: 2200mm, weight: 450kg without feeder. On-site inspection is possible. Cjljwb E Snjn Sx T Sjrb

Condition: used, Year of construction: 2024, pressure 100 t stroke 300 mm table surface area 1070 x 315 mm column travel between the guideways 1070 mm ajustment speed 8.0 mm/sec working feed 5.0 mm/sec return speed 10.0 mm/sec oil volume 90.0 l engine output 5.5 kW weight of the machine ca. 1870 kg. dimensions of the machine ca. 2050 x 1000 x 2200 mm Display machine from 2024 With only approximately 2 operating hours Like new condition Special price upon request Furnishing: - Robust electro-hydraulic workshop press, with adjustable cylinder - Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more. - Robust welded steel construction for high demands - Table height adjustment via piston rod * including round steel chain and 2x locking bolts * Piston rod with metric socket - 1x set of V-block prism supports - Manometer for pressure display - simply constructed hand control with: * 1x delivery speed * 1x working speed * 1x retreat speed - Piston can be stopped in any position Croln Sx Tjixmz Uj Ssb - Hydraulic tank mounted on the side - Operation manual

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, Functionality: fully functional, pressing force: 100 t, bale weight: 1,400 kg, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale height: 1,100 mm, bale width: 1,100 mm, overall weight: 36,000 kg, oil tank capacity: 1,300 l, nominal current: 238 A, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Crsln Ssvf E Avsx T Sob Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 2024, Condition: as good as new (ex-display), Functionality: fully functional, Rental Hosokawa Alpine UPZ 100 cryogenic system (LN2) by Alpine Rentals. Technical details Design: Non Pressure Shock Resistant (NPSR), non ATEX Suitable for cryogenic grinding with LN2 Material of construction: stainless steel Without wear protection Batch operation, for a few kilos normally (product dependent) Scope of supply 100 UPZ system with grinding tools of choice, small feeding hopper with a dosing channel, cooling screw to feed the LN2, LN2 container, filter and barrel to collect the fines. Includes an operating panel, switch cabinet and a vacuum cleaner. LN2 to be provided on-site This small size system with an universal mill UPZ 100 can be used for the production of small batches as well as for R&D purposes. Thanks to the different grinding accessories it can be adapted to different tasks and target fineness. Suitable for the cryogenic grinding with liquid nitrogen of different products, to help in their grinding process (plastics for instance) or maintain their properties (food for instance). The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mill. It is used to grind soft dry materials. This micronizer is perfect to pulverize different coarse products down to a finer powder and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetics, recycling, etc. This grinder can be used for the pre-cut of different materials. It is able to process coarse products up to approx. 3 Mohs´ hardness by reaching medium to fine particles with end-product fineness values between d97 150 to 850 microns (µm) top size (product dependent) at the lowest possible energy consumption. The turbo mill can reach this wide final product range thanks to a variety of easily interchangeable grinding tools such as pin disc, plate beater, beater disc or pendulum beater. Certain grinding tools can operate together with different grinding tracks (liners), sieves or a combination of both, to achieve the desired fineness. This allows the same machine to process many different products such as fibrous roots or spices to plastics, granulated chemicals or mineral products. The comminution takes place inside the grinding chamber where the rotor plate fitted with grinding tools impacts and projects the particles against the grinding track or sieve (if fitted) reducing their size. The process gas then transports the fines to the mill outlet towards the next stage, normally the filter. Thanks to the required process air volume, reduced temperature increase during grinding is to be expected compared to other granulation and crushing technologies. Adjusting the final particle size distribution can be easily done by changing different parameters, such as the speed of the grinding rotor or disc, the type of grinding tool and liner, air volume, feeding rate, etc. A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery Creln Soq Rv Hhex T Seb

Condition: used, Year of construction: 1985, Technical details: pressure: 100 t no. of strokes: 35-100 Hub/min throat: 360 mm ram adjustment: 20-130 mm ram surface area: 750x550 mm clamping plate on table: 1000x640 mm adjustment of stroke: 90 mm passage between the columns longitudinal/sideways: 610x500 / 440x550 mm daylight dimension : table/slide low: 300 mm total power requirement: 17,5 kW Croln Sxou Nfh Dj T Seb weight of the machine ca.: ca,7,0 t dimension machine xH: 1,9x1,4x2,7 m - there are 5 T-slots lengthwise on the ram plate - centre hole = 50mm This press is currently for sale without controls. Optional on customer request completion possible. i.D. *

Condition: refurbished (used), Year of construction: 2025, Functionality: fully functional, machine/vehicle number: A5137, Refurbished 100-ton HEILBRONN C-press, currently undergoing retrofitting - available at short notice. Hydraulic clutch-brake combination, automatic central grease lubrication, manual ram adjustment, mechanical overload protection, new lubrication/hydraulic hoses, etc., new control system (adjustments still possible). Dimensions - see machine drawing as PDF. Technical specifications: Press force: 1,000 kN Speed: 50 rpm (variable speed optional) Variable stroke: 14 - 150 mm Ram adjustment: 80 mm Installation height: 420 mm (max. stroke at bottom, adjustment at top) Table: 650 x 500 mm Coln Sxewb A Dzs T Ssrb Ram: 400 x 250 mm Thrust: 350 mm Drive power: 5.5 kW Approx. weight: 5,500 kg

Condition: good (used), Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams, swivel cylinders -Hydraulic cylinder: double-acting stroke 100 mm Cjln Ssv I S Iqsx T Serb -Piston rod: Ø 37 mm -Holes: Ø 25 mm / Distance: retracted 365 mm / 360 mm -Number: 2x cylinders available -Price: per piece -Dimensions: Ø 82 x 440 mm -Weight: 7.7 kg / 7.8 kg

Condition: excellent (used), Year of construction: 2017, operating hours: 879 h, lifting height: 2,900 mm, mast type: duplex, battery capacity: 225 Ah, battery voltage: 24 V, fork length: 1,300 mm, Field of application: Internal logistics Lifting capacity: 1.000 kg Technical condition: very good Colowb Amvjn Sx T Sorb Visual appearance: very good Serial number: 6499264 Please contact PEDRO GÓMEZ for more information

Year of construction: 2000, Condition: excellent (used), Maschinen-Details Lagernummer 1105-03787 Maschinenart Bearbeitungszentrum - Vertikal Fabrikat TRENS Typ MC 100 VA Baujahr 2000 Steuerungsart CNC Steuerung HEIDENHAIN TNC 426 Lagerort FRANKREICH Ursprungsland Tschechei Lieferzeit sofort Frachtbasis ab Lager, frei verladen Lkw Crsln Soiwgi Nsx T Ssb Technische Details x-Weg 1015 mm y-Weg 610 mm z-Weg 508 mm Tischgröße 1080 x 580 mm Spindelaufnahme ISO 40 Bohrleistung in St 60 - Vollbohren 45 mm Gewindeschneiden bis M 24 Drehzahlbereich - stufenlos 20 - 8000 U/min Vorschübe - längs/quer/senkrecht 1 - 5000 mm/min Eilgang 20 m/min Entfernung Spindel/Tisch 100 - 608 mm Anzahl der Werkzeugmagazinplätze 40 Werkzeugdurchmesser bei voller Bestückung 80 mm Werkzeugdurchmesser bei 2 Freiplätzen 125 mm Werkzeuglänge max. 380 mm Werkzeuggewicht max. 7 kg Werkzeugwechselzeit 7 sec Spindel 11/16.5 kW Steuerung HEIDENHAIN TNC 415 Gesamtleistungsbedarf 30 kVA Maschinengewicht ca. 5,7 t Zusatzinformationen DoKUMENTE heidenhain tnc 426

Year of construction: 2023, Condition: new, Functionality: fully functional, Rental system Hosokawa Alpine AS 100 Aeroplex The Hosokawa Alpine Aeroplex AS spiral jet mill is a simple jet mill without dynamic classifier (different to our Hosokawa Alpine AFG) that allows the ultrafine micronization with a final fineness of around 10 to 150µm of different products. Mainly dry non abrasive materials up to 3 Mohs hardness can be pulverized although some models allow wear protection inserts within the grinding chamber (pending availability). The micronizer design without rotating parts (thus no bearings or grease) makes this mill especially suitable for pharmaceutical and food applications, although it´s used as well on the chemicals industry for instance. The comminution takes place inside the grinding chamber where the product is accelerated by the compress gas injected through the grinding nozzles causing the different particles to collide with each other and break reducing their size. Once they are fine enough they are attracted to the central outlet, acting as a sort of static classifier but without a precise sharp top cut in comparison to the AFG (which is fitted with a rotating classifier wheel). Once the comminuted particles make it through, they exit the system either to a cyclone or directly to an air filter. Thanks to the required process air volume, reduced temperature increase during grinding is to be expected compared to other granulation and crushing technologies. Adjusting the final particle size distribution can be easily done by changing different parameters, such as the gas pressure on the grinding nozzles or the feed injector, air volume, feeding rate, etc. A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Crjln Sx Toq A T Ile Sjb Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery Technical details Stainless steel construction, pharma design Non Pressure Shock Resistant (NPSR), suitable for inert operation (N2) Batch operation, for a few grams normally (product dependent) Scope of supply Complete small system comprising dosing channel, spiral jet mill with manual pressure control and filter bag

Condition: good (used), Year of construction: 2017, operating hours: 5,750 h, Functionality: fully functional, power: 110 kW (149.56 HP), input voltage: 400 V, filling opening width: 1,020 mm, filling opening length: 1,500 mm, UNTHA RS-100 Shredder Main shaft speed: 17.3 rpm Side shaft speed: 28.0 rpm Creln Sov R Hc Iox T Sjb Chipping disc width: 38 mm Drive power: 2x55 kW, 400 V, 50 Hz Round screen perforation: Ø 25 mm and 80 mm Total weight without base: approx. 12,000 kg Control cabinet with wiring: complete Incl. hopper + pusher and base Clean machine, checked, always maintained, 1 owner!

Condition: used, overall weight: 36,000 kg, maximum load weight: 27,980 kg, axle configuration: 3 axles, loading space length: 13,530 mm, loading space width: 2,480 mm, loading space height: 2,730 mm, loading space volume: 92 m³, first registration: 07/2023, total width: 2,550 mm, total height: 4,000 mm, Equipment: ABS, Moving floor +/- 92 cubic meters, galvanized chassis, "Cargo Floor" floor with 21 boards approximately 10 mm thick, stainless steel wear plate at the rear under the moving floor, complete emptying (rolling bulkhead), push-in/push-out function, double-wing door with espagnolette lock at the rear, access and standing area at the front of the body, roll-up tarpaulin, load gauge, LED side marker reflectors, folding rear light guards, ABS, EBS, BPW axle(s), disc brake system, air suspension with lifting/lowering device, lift axle, "Jost" landing gear, spare wheel holder for 2 spare wheels, vehicle can be covered with advertising and/or lettering. Crjln Sxev Nfcqs T Seb Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is desired, we would be happy to provide you with an offer from our partner workshops! The vehicle can be covered with advertising and/or lettering. Our general terms and conditions of delivery and payment apply. We would be happy to provide you with a financing or leasing offer for this property. Please contact us!

Condition: good (used), Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Manufacturer: Rexroth, hydraulic cylinder type CD250B40/28-100 -Stroke: 100 mm -Piston rod: Ø 28 mm / M16 x 1.5 -Hole: Ø 25 mm -Number: 2x cylinders available -Price: per piece -Dimensions: Ø 88 x 400 mm Cslnounn I No Sx T Ssrb -Weight: 5.9 kg/pc.

Condition: used, Year of construction: 2016, Functionality: fully functional, overall weight: 450 kg, type of input current: three-phase, height adjustment type: mechanical, input voltage: 400 V, – Italian production – year of production 2016 – pre-milling – DTR, CE TECHNICAL PARAMETERS: – edge thickness: 0.5 - 3 mm – wooden edgeband: 0.5 - 5 mm – element height: 8 - 50 mm – minimum edgebanding length: 160 mm – minimum board width: 110 mm – feed speed: 7 m/min – pre-milling – radial cutters – edge cutting – radial scraper – straight scraper – blower for each unit – working pressure: 8 bar – working machine length: 2030 mm Crolnewb Ha Tj Sx T Sjb – transport dimensions (length/width/height): 330/80/125 cm – weight: 450 kg