Used Glob-Ram Rm733S Sorteergrijper for sale (3,530)

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test. Cgodpfxjx A U Nco Afysp

Condition: used, mileage: 71,100 km, power: 295 kW (401.09 HP), fuel type: gasoline, gearing type: automatic, first registration: 02/2017, emission class: euro6, color: white, number of seats: 3, Equipment: ABS, air conditioning, all wheel drive, central locking, electronic stability program (ESP), * DODGE RAM 2500 4x4 with original 71,800 km - Petrol - no LPG - New MOT (TÜV) - Registered as truck (N1 category) - * 5.7 l petrol engine - displacement: 5,654 cc - 295 kW / 401 HP - Euro 6 - green emissions sticker - * VIN: 3C6TR5DT6GG236296 - German registration documents - second owner - * Tow bar with 3,500 kg braked towing capacity - 750 kg unbraked - * Vehicle immediately available - vehicle is wrapped in green - original color is white - * Not a salvage import - accident-free with verifiable history - * Viewings by appointment only - * Contact person: Mr. Andreas Vogel * The information provided online is non-binding and for descriptive purposes only. Codpfsyg T E Sox Afyegp * They do not constitute guaranteed features. * The seller is not liable for typographical or data transmission errors. * Subject to alterations, errors, and prior sale.

Condition: good (used), PLC control, central assembly, RAM, CPU, central device, central processing unit, compact device, compact CPU, processor Cgedjn Nbmzspfx Afyop -Manufacturer: mushroom, processor -Type: P10 CPU/RAM 304060 -Dimensions: 250/230/H40 mm -Weight: 1.3 kg

Condition: used, Attachment suited for: Construction machines Cjdpfeyfm Dxsx Afyogp

Condition: used, Year of construction: 1997, Technical details: spindle diameter: 180 mm x-travel: 6.000 mm y-travel: 2.900 mm total power requirement: 95 kW weight of the machine ca.: 130 mit Zubehör t z-travel: 1.250 Ram mm w-axis: 1000 Spindel mm ram stroke: 1250 mm dimension of the ram: 450 x 450 mm bore spindle stroke: 1000 mm bore spindle turning speed range: 920 1/min powered rotary table: IOS 40 CNC 2 Achsen B u.V Rotary-table: 3000 x 3500 mm Rotary-table: CNC-IOS 40 NC mm Cgsdpforu Rfhsx Afysp stepless adjustable, relative to diameter: Index 4x 90° -360000 Winkel =0,001 Grad mm travel - cross: Längs 1230 mm table load of rotary table max.: 40 Tonnen clamping plate: 3 x 8000 x 2000 mm CNC Ram-Type Floor Boring and Milling machine, dismantled and stored The headstock sliding guides were recoated and scraped. *

Condition: used, Technical details: spindle diameter: 150 mm x-travel: 10000 mm y-travel: 2500 mm Cedpfx Afswg R Swsysgp bore spindle stroke: 700 mm ram stroke: 700 dimension of the ram: 340 x 340 mm spindle taper ISO: 50 Speed of boring spindles: 1,25 - 1250 U/min. feed speeds infinitely variable: 1 - 5000 mm/min rapid traverse: 5 m/min total power requirement: 120 kW weight of the machine ca.: 115 t dimensions of the machine ca.: 15,1 x 10 x 6,4 m with CNC SIEMENS 840 Dsl complete retrofit in 2010 FIBRO CNC rotary table 2500 x 2500 mm, 50 to. loading capacity, longitudinal movement 2500 mm, angular milling head 4 x 90° universal milling head floor plate area ca. 12000 x 6000 mm ( 72 m²) chip conveyor and coolant attachment aerostatic guideways *

Condition: ready for operation (used), Siemens Teleperm M 6DS1837-8EA Ram memory module E Stand 2 SN CO960610 used 100% functional Cgsdpfx Asxahx Sefyep

Condition: new, Siemens 6FX1138-6BL01 PLC 135WB/ACOP, 256KB RAM E-Stand: C SN:1359, unused in opened original packaging, 100% functional, scope of delivery as shown in photos Cgedpfxjxagqme Afyep

Condition: ready for operation (used), Siemens Teleperm M 6DS1837-8EA Ram memory module E Stand 2 SN CO972591 used 100% functional Cjdpfxexahycs Afysgp

Condition: used, functionality: fully functional, Year of construction: 1994, 1 used residual concrete recycling plant Year of manufacture 1994 Fully functional Needs minor repairs consisting of Base machine Cgjdpfx Ajw Sawfsfysp Feeding table Winter enclosure (without control unit) from location near Fulda - Sold as is - subject to prior sale

Year of construction: 2012, condition: refurbished (used), Fresh concrete recycling plant BIBKO RAM 20/ used manufactory: Bibko type: RAM 20 YOM: 2012 Capacity: ca. 12 m³/h system washing trough, trough length 2500 mm separating layer 0,25 mm Cgodpjdvuurofx Afyop with discharge conveyor screw (new) overhauled/reconditioned and exactly aligned - gear reconditioned (overhauled) and sealed - all bearings are new - buckets and scraper exactly aligned Optional by surcharge: - 1 pcs feed hopper / used - 1 pcs agitator (wastewater) with console / used - 1 pcs control unit / used -for the full automatic control of the complete plant - 1 pcs gallows-shaped pipe/ used Facility is fully equipped, clean and primed. The final painting according to customer's request. location: South Germany offer and all price are net and ex stock without guarantee and/or guarantee, mistakes and/or false representations reserve, purchasing like see / how is it – standing or recumbent, subject prior sale _____ IT IS FORBIDDEN TO COPY OR PUBLICATE THIS OFFER BY ANY THIRD PARTIE OR THIRD PERSON.

Condition: used, mileage: 665,997 km, power: 338 kW (459.55 HP), first registration: 03/2016, fuel type: diesel, tire size: 315/80R22.5, axle configuration: 4x2, wheelbase: 3,700 mm, fuel: diesel, color: white, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, suspension: steel-air, Year of construction: 2016, Equipment: air conditioning, electric window regulation, Tyre size: 315/80R22.5 Cgjdpfjxxxxajx Afyop Front axle: Suspension: leaf suspension Rear axle: Double wheels; Suspension: air suspension Drive: Wheel Number of cylinders: 6 Empty weight: 7.482 kg Carrying capacity: 11.518 kg GVW: 19.000 kg Make of engine: Volvo

Condition: used, functionality: unexamined, Ferwood code: RU0007166 - Manufacturer code: 2-083-01-5004 - Condition: Used - Functionality: Not tested - If you are interested, we offer an overhaul service. Please contact us. Cjdpfx Ajwtf Tcofyegp

Condition: new, Year of construction: 2020, Empty weight: 293 kg Height: 85 cm Cgodox I Ev Hspfx Afyjp Attachment suited for: Construction machines

Condition: new, Year of construction: 2024, Attachment suited for: Construction machines Cjdpsx I Erbjfx Afyegp

Condition: excellent (used), Year of construction: 1972, total power requirement 22 kW weight of the machine ca. 8 t Q U O T A T I O N We are pleased to offer you ex our stock, subject to prior sale, and error in technical data : DISKUS Double Disc Surface Grinding Machine in C-form with rotary workpiece feeding system and automatic dressing cycle model DDS 600 RAM year 1972 / 2002 modernized Serial no 6967 _____ Grinding wheels Ø, each 600 mm Grinding wheels bore x height, approx. 75 / 150 mm Grinding wheel speeds Upper wheel 95 – 955 rpm (3-30 m/s) Lower wheel 765 rpm (24 m/s) Grinding spindle drive, each 30 kW Workpiece dimensions: Grinding width (or workpiece diameter) approx. 20 - 120 mm Grinding (workpiece) height max 50 mm Hydraulic infeed impulse 0.0025 – 0.05 mm Total feed way 150 mm External Ø of workpiece carrier disk 810 mm Feeds of rotary workpiece feed system, infinitely variable 25 – 241 mm/s Total electrical load, approx. 50 kW - 380 V - 50 Hz Weight, approx. 8,000 kg Accessories / Special Features: • In 2002 updated IONIC gauge control Model 17A with monitor and direct input of workpiece data including tolerance range, workpiece counting, statistics. The workpieces are continuously measured via two opposite tracer heads, automatically triggering an hydraulic infeed when needed. • Rotary workpiece feed system with Workpiece carrier wheel (Ø 800 mm) and infinitely variable speed adjustment. • Workpiece height check to avoid crashing with griding wheels • Automatic hydraulic dressing device between the two grinding wheels for simultaneous dressing of both wheels. Dressing cycle can be preset (no. of workpieces/time). Hydraulic return of upper grinding slide to original position/workpiece/thickness (saves a lot of time). • ELBARON Oilmist Extractor with stand and adjustable suction cone • Walkable steel podium for easy machine operating and monitoring • Grinding wheel exchanging device, various spare grinding wheels Csdjxqrbxjpfx Afysgp • Central lubrication using grease and oil mist * Separate switch cabinet. * Separate hydraulic unit. • Currently no coolant filtration device available (can may be supplied separately). This machine is ideal for double-sided simultaneous grinding of parallel workpiece surfaces by continuous method, for maximum output and accuracy in mass production (e.g. Bearing rings, Piston rings, washers, hydraulic parts, and other pressed parts.) Condition : very good ! Very well maintained ! Please click here to soon view a video of the machine running : ! Delivery : immediately available, FCA Metzingen Payment : 100 % Net, after conclusion of contract, before loading

Condition: used, mileage: 717,653 km, power: 338 kW (459.55 HP), first registration: 03/2017, fuel type: diesel, tire size: 315/80R22,5, axle configuration: 4x2, wheelbase: 3,700 mm, fuel: diesel, color: white, gearing type: automatic, emission class: euro6, suspension: steel-air, Year of construction: 2017, Equipment: air conditioning, electric window regulation, Tyre size: 315/80R22,5 Front axle: Suspension: leaf suspension Rear axle: Double wheels; Suspension: air suspension Drive: Wheel Empty weight: 7.470 kg Carrying capacity: 11.530 kg GVW: 19.000 kg Cjdpfxexp Nc Ds Afysgp

Condition: used, mileage: 704,235 km, power: 338 kW (459.55 HP), first registration: 02/2016, fuel type: diesel, tire size: 315/80R22,5, axle configuration: 4x2, wheelbase: 3,700 mm, fuel: diesel, color: white, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, suspension: steel-air, Year of construction: 2016, Equipment: air conditioning, electric window regulation, Tyre size: 315/80R22,5 Front axle: Suspension: leaf suspension Rear axle: Double wheels; Suspension: air suspension Drive: Wheel Empty weight: 7.472 kg Carrying capacity: 11.528 kg GVW: 19.000 kg Codpfx Afoxp Ncwsyegp

Condition: good (used), Manufacturer: STANKO Type: 7D430 Year of manufacture: 1994 Cgodpfx Ajwpud Aofyop Table rotation 360° Head tilting possible up to 10° Big cabinet with slotting key way tools Lubrication Completely overhauled in 1994 Specifications Metric US Standard Table diameter Ø 630 mm Table load 1000 Ram displacement 320 mm X - Axis 650 mm Y - Axis 510 mm Outreach 500 mm Number of strokes 3 - 38 m/min min. Power 12 kW Dimensions (estimated) Length 3000 mm Width 2200 mm Height 3000 mm Weight 6150 kg Please note: The information on this page was provided to the best of our knowledge and ability by us, and, where possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not constitute representation and contractual terms. We recommend that you verify all important details.

Condition: used, functionality: fully functional, mileage: 90,000 km, power: 183.87 kW (249.99 HP), fuel type: diesel, gearing type: automatic, axle configuration: 4x2, first registration: 06/2021, emission class: euro6, color: black, number of seats: 5, number of previous owners: 1, Equipment: ABS, air conditioning, airbag, all-season tires, central locking, cruise control, fog lights, immobilizer system, onboard computer, parking sensors, power assisted steering, seat heater, soot filter, traction control, trailer coupling, RAM 1500 New Model Gen.5 Night Edition Blackout Package New bed cover Cgedpfxsx Eizgj Afyep New running boards New all-weather tires Heated seats Heated steering wheel Large display Apple CarPlay Tow hitch (AHK) Full German registration Not 4x4, but still excellent traction thanks to all-weather offroad tires Repaired accident damage – sheet metal and front suspension were repaired and repainted by us. Top condition!!! Single owner Serious purchase inquiries only, please! The truck comes with too many extras to list – for more details, feel free to contact us via email or phone. – Price includes German registration documents. – Subject to errors and prior sale. – Financing and trade-in possible, all offers welcome. – Tipping hydraulics available for an extra charge!!! Our motorhomes are customs-cleared and taxed in Germany, including EU vehicle registration documents. With us, quality is guaranteed—you have our word. Didn’t find your dream vehicle in Europe’s largest US truck inventory? Didn’t see your company’s or favorite color? No problem… We have over 500 additional trucks and motorhomes—new and used—of all brands in the USA and Canada. We also work with one of the best paint shops in Germany. Let us advise you and provide a free quote. We look forward to your call. Viewing appointments are by appointment only.

Condition: not inspected (used), functionality: unexamined, Harris TGS 215 3-RAM metal baler, 16” square with 600kw hydraulic power pack and hopper Video of baler in operation available on request, further details and photos to follow Cedpfew E Htujx Afysgp Machine decommissioned

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, Ram-Type Floor Type and Milling Machine with SCHARMANN rotary sliding table Brand: SKODA / Type: W200 Basic body constructed in 1986 / 1999 Overhaul / Retrofit on CNC by SKODA. Cgjdpfx Afswxyxqjyop The machine can be inspected by appointment. Technical specifications: Travels: X-axis: 8.000 mm Y axis: 4.150 mm W-axis: 2.000 mm Z-axis: 1.600 mm Spindle: - Spindle diameter: 200 mm - Tool taper to DIN 2080 AD, ISO 60 - Spindle speed: 0,0 to 930 rpm - Drive power spindle: 77 kW Rotary table: - Manufacturer: SCHARMANN - Table surface area: 6.000 x 4.000 mm - V-axis: 2.000 mm - Table load max.: 80 tons - B-axis: 360 ° A, graduation: 0.001 A ° Equipment: - CNC-Control: SIEMENS Sinumerik 840 CE - Chip conveyor - ... There is no guarantee for correctness and completeness of the technical details and accessoires. - Subject to prior sale. Detailed technical data sheet and information on equipment available on request.

Condition: new, Year of construction: 2022, Field of application: Construction CE mark: yes Production country: NL Please contact Kristoff Van Havere for more information Cedpfx Aogfu Nmjfysgp

Condition: new, functionality: fully functional, Year of construction: 2025, Postmaster MINI – Hydraulic Vibrating Block The Postmaster Mini can be mounted directly onto a machine, ranging from 1.5 to 3 tons, and drives posts into the ground up to 150 mm. Oil supply required is 30-40 l/min. The Postmaster is faster, quieter, and safer than conventional machines on the market. A unique clamping system holds the post in position and vibrates it into the ground with minimal damage. Thanks to this vibrating action, the Postmaster can also be used to extract posts from the ground. Ideal for both wooden and steel posts and especially suitable for installing solar parks. • Faster • Safer • Quieter Codpfow R Uqkex Afyogp • Removes posts from the ground • Minimal ground disturbance • Firmly secured The Mini is the smallest unit in the range and weighs just 160 kg. Its compact design and light weight make it safe for use on smaller excavators without compromising stability. This unit is an ideal partner for short runs, limited access, and rapid repairs. Also available in Midi and Maxi versions. Optional CW 05 top plate.

Condition: used, functionality: fully functional, throat depth: 80 mm, total width: 100 mm, total length: 220 mm, ram adjustment: 77 mm, table width: 100 mm, table length: 160 mm, installation height: 140 mm, overall weight: 17 kg, space requirement length: 220 mm, space requirement width: 100 mm, stroke length: 25 mm, Toggle Press / Hand Lever Press with Square Ram Make: Steinel Cgodpfx Afexyw A Hsyjp Type / Machine Number: PHK 8 Press Force: 6 kN Table Size: 100 x 160 mm Throat Depth: 80 mm Stroke: 25 mm Installation Height: 63 – 140 mm Height Adjustment: 77 mm Ram Bore: Ø 10 mm Machine Weight: 17 kg Space Requirement: 100 x 220 x 600 mm