Used Glob-Ram Rm130 for sale (22,713)

Year of construction: 1995, Condition: good (used), The bender can bend aluminum and plastic, Djb Hhsrif U Eeu Uzjcg Total length: approx. 11500 mm, depth: 1600 mm. Available from approx. June / July 2024.

Condition: used, Used machine Dcjb Hskwhgcehu Uzsg Used pneumatic frame press from Maweg MNo.: 7004124588 Pressing area: length approx. 3500 mm / height approx. 2450 mm 2 horizontal press cylinders 3 vertical press cylinders Availability: by arrangement Location: Röllbach

Year of construction: 1973, Condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance Dcjb Hhsh U Rzgsu Uzog - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: good (used), Underframe for conveyor belt, belt conveyor, conveyor belt, belt conveyor, belt conveyor, flat belt conveyor, roller conveyor, roller conveyor stand Djb Hhov U T H Iju Uzjcg -Subframe: longitudinal member -Type: Length 2000 mm -Number: 50 pieces of longitudinal beams available -Price: per piece -Roller conveyor: suitable in stock, see ID 35086 -Transport dimensions: 2000/45/H140 mm -Weight: 7.3 kg/piece

Condition: used, Year of construction: 1967, installation height: 407 mm, pressing force: 100 t, tool height: 407 mm, CONTROLS .. conventional PRESS DESIGN Dob Hhu Ujwbd T Djzocg .. drive system: eccentric / crank .. frame design: C-frame, single sided PRESS FORCES .. total force (nominal): 100 to SLIDE .. slide force: 100 to .. stroke rate (max.): 72 /min SLIDE (MECHAN. PRESS) .. slide adjustment: 80 mm .. stroke adjustment: yes .. stroke min.: 8 mm .. stroke max.: 112 mm TOOL ASSEMBLY DIMENSIONS .. shut height (stroke down, adjustment up), BDC: 407 mm ATTACHMENTS (PRESSES) .. 2-hand engagement: yes for safe tools only

Condition: good (used), Code: 0089 Brand: VILMAR PRESSE - ITALY Model: PS 1000 Hydraulic press for mouldings, frames, furniture elements, plastics, composites and various materials Dcob Hhuowbu I Se Uzeg Technical data: Platens size mm 980 x 500 Opening mm 300 N°3 pistons diameter mm 160 each Total thrust pressure up to 250 tons Safety photocell barrier Double push buttons Hydraulic power unit Kw 4 Heating platens up to 300 degrees Power absorbed heating platens 8+8 Kw Overall dimensions mm 1600 x 1000 x 2200 h Weight kg 3400

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Vacuum system (with its pump) No. 2 Vertical supporting columns of the top supporting beam No. 1 Horizontal top supporting beam (where the carriage slide on) No. 1 Motorized sliding carriage with horizontal metal arms N. 2 Out-side rollers ways (on gound) to in-feed pile of panels to the Loader N. 1 Out-side motorized rollers table (which out-feed the panels from the Loader) Separate electric and command panel Perimetral safety metal grids Working capacity (cycles/min) 16 (ca.) Min/Max panels thickness mm 10 / 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1300 x 3000 (ca.) Total installed motor power Kw 80 Djb Hhjwbp Nwsu Uzscg

Condition: used, Year of construction: 1991, used frame press pneumatic working size 3500 x 2500 mm with medium pressure beam absolute angular accuracy without correction comfortable working height due to the possibility of adjusting all pressing corners operation of the working cylinders via 2 air valves all pressing corners are adjustable the pressures are adjustable from 0-15 bar available kit: short term Debokwhi Hs Hhu Uzjcg storage location: Röllbach

Condition: excellent (used), Year of construction: 2019, Digital ceramic printing system for flat glass. Max. glass size: 2400 x 4200 mm. Working height: 940 mm. Total length: approx. 5630 mm. Dsbjqlapzo Hhu Uzocg Max. Width of the machine: approx. 4800 mm. Available from approx. end of January 2024.

Condition: good (used), Underframe for conveyor belt, belt conveyor, conveyor belt, belt conveyor, belt conveyor, flat belt conveyor, roller conveyor, roller conveyor stand -Subframe: longitudinal member -Type: Length 2000 mm -Number: 65 pieces of longitudinal beams available Dcob Hhsv U T Hhou Uzeg -Price: per piece -Roller conveyor: suitable in stock, see ID 35086 -Transport dimensions: 2000/120/H110 mm -Weight: 12.4 kg/piece

Condition: used, Year of construction: 2015, operating hours: 3,300 h, Functionality: fully functional, feed length X-axis: 13,700 mm, cutting height (max.): 200 mm, cutting width (max.): 455 mm, air demand: 1,250 m³/h, saw blade diameter: 555 mm, power: 20 kW (27.19 HP), WEINMANN WBS 140/13 5-axis machining center 5-axis spindle – 8-position tool changer – Machining – Marker – Printer – Labeling – Software package Available machining options: Half-timbering, Z-type end beam assembly – All beam end machining and cuts – Valley – Hip – All straight and mitre cuts – Purlin trimming – Beveled and other longitudinal milling – Mortise and tenon – Dovetail joints. 8-position tool changer with pickup – 8 tool positions Machine condition: Very compact machine! In excellent technical and visual condition, serviced and lubricated with all tools! Machine availability: From June 2025 due to local relocation Djb Hhuswfqgrs Uzecg Videos are available and, of course, we are welcome to visit the site.

Year of construction: 1995, Condition: ready for operation (used), Cutting angle (fixed): 45°, max. cutting height: 50mm, max. cutting width: 100mm, max. saw blade diameter: 250mm, machine dimensions X/Y: approx. 500mm/1100mm. On-site inspection is possible. Dsb Hhjwfg E Rju Uzecg

Condition: excellent (used), STACKER (BRIDGE-FRAME) WITH DOUBLE STORAGE STATION Vacuum system (with its pump) Deb Hhst Ty A Aeu Uzscg No. 2 Vertical supporting columns of the top supporting beam No. 1 Horizontal top supporting beam (where the carriage slide on) No. 1 Motorized sliding carriage with horizontal metal arms No. 2 Out-side rollers way (on ground) to out-feed pile of panels from the Unloader/Stacker No. 1 Out-side motorized rollers table (which brings panels to the Unloader) Separate electric and command panel Perimetral safety metal grids Working capacity (cycles/min) 16 (ca.) Min/Max panels thickness mm 10 / 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1300 x 3000 (ca.) Total installed motor power Kw 80

Condition: used, Year of construction: 1993, Used machine Year of construction 1993 Automatic frame press Working area 3550 x 2400/2600 mm pressure range 120 bar Pressure per 21000 N/kp Cylinder stroke vertical 250 mm, horizontal 20 or 80 mm Automatic control Electrical connection with medium pressure bar Special equipment: Dcjb Hhuokwg Tmj Uzjg Impulse "Open press" Vertical positioning device Width compensation allowance for 1 MB 1 additional horizontal pressure cylinder Spring weight compensation Work safety device pull rope Installation dimensions 5150 x 1500 x 3340 mm Weight 2500 kg Electrical connection 3.5 kW Compressed air connection R 3/8" max 8 bar Availability: short term Location: Röllbach

Condition: good (used), Frame Saw rollers in cast iron Dcob Howag Syohu Uzjg 2 pc. top (71/75) 2 pc. bottom (OSS/E-ESS)

Condition: good (used), Underframe for conveyor belt, belt conveyor, conveyor belt, belt conveyor, belt conveyor, flat belt conveyor, roller conveyor, roller conveyor stand -Base: height adjustable -Type: Width 1180 mm -Height: 200 mm, adjustable -Number: 14 trusses available -Price: per piece Dsbjv U Tzls Hhu Uzjcg -Roller conveyor: suitable in stock, see ID 35086 -Transport dimensions: 1180/150/H200 mm -Weight: 4.9 kg/piece

Condition: ready for operation (used), OMGA V113P double saw for frames, strips Deb Hhu Uewgdgnjzscg Specification: • condition - used • manufacturer - OMGA • model - V113P • two 300 mm diameter discs permanently set at a 45 degree angle each • total power 2.2 kW (2 engines of 1.1 kW each) • spindles fi 30 mm • pneumatic clamps • cutting cross-section ~ 100 x 130 mm • original painting • additional tables extending the tops by 100 cm (2 pcs.) • 1993 year of production • weight 225 kg • dimensions 80 x 142 x 132 cm cm (length x width x height) Additional information: • very good, factory technical and visual condition • the photos shown show the actual condition of the item for sale • possibility of switching on and checking the device on site

Condition: ready for operation (used), A Seitz filter machine including a Schenk dosing device for beer production is available. 1) Kieselguhr frame filter Seitz Orion 60, max. throughput capacity: 70hl-80hl/h, effective throughput capacity: approx. 45hl/h, max. total filtration capacity: approx. 600hl, pressing device: 2-stage planetary gear, number of plates: 36, number of end plates: 2, plate dimensions X/Y: 600mm/600mm, pipe diameter: 50mm, nominal width: NW50, machine dimensions X/Y/Z: approx. 3800mm/1100mm/1400mm. 2) Dosing device Schenk DO-S120, year of construction: 1971, capacity: approx. 160l/h, high-speed capacity: approx. 320l/h, nominal width: NW50, pipe diameter: 50mm. Documentation available. On-site inspection is possible. Dcjbswd Talj Hhu Uzeg

Condition: used, Linpac 15pcs. transport trolleys for Trolley euroboxes underframe 800x600x200 mm 300kg load capacity RA2210 Technical data: Length: 800 mm Width: 600 mm Height: 200 mm Load capacity: 300 kg for two paralell euroboxes Material: stable plastic body Underride height: approx. 100 mm Weight: approx. 9.1 kg Configuration: 2 steering and 2 fixed castors Purchase quantity 15, stacked L x W x H approx. 800 x 600 x 2270 mm Total weight: approx. 136.5 kg Year of manufacture: unknown Stackable: yes, through cutouts Condition: Used / fully functional Djb Hhuotu Rmge Uzecg Color: red Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: used, Year of construction: 2013, Functionality: fully functional, machine/vehicle number: 9 045 0090, overall weight: 18,200 kg, power: 40 kW (54.38 HP), For sale Essetre Techno One from 2013 following move. Dob Hhuswd E Sms Uzocg

Condition: good (used), Underframe for conveyor belt, belt conveyor, conveyor belt, belt conveyor, belt conveyor, flat belt conveyor, roller conveyor, roller conveyor stand -Base: height adjustable -Type: Width 1180 mm -Height: 295 mm, adjustable -Number: 14 trusses available -Price: per piece -Roller conveyor: suitable in stock, see ID 35086 Dcsb Hhusv U Tyzo Uzjg -Transport dimensions: 1180/150/H295 mm -Weight: 7 kg/piece

Condition: good (used), Underframe for conveyor belt, belt conveyor, conveyor belt, belt conveyor, belt conveyor, flat belt conveyor, roller conveyor, roller conveyor stand Djb Hhu Uev U Ttuezecg -Base: height adjustable -Type: Width 1180 mm -Height: 400 mm, adjustable -Number: 14 trusses available -Price: per piece -Roller conveyor: suitable in stock, see ID 35086 -Transport dimensions: 1180/150/H400 mm -Weight: 8 kg/piece

Condition: good (used), Underframe for conveyor belt, belt conveyor, conveyor belt, belt conveyor, belt conveyor, flat belt conveyor, roller conveyor, roller conveyor stand -Base: height adjustable -Type: Width 1180 mm -Height: 460 mm, adjustable -Number: 13 trusses available -Price: per piece -Roller conveyor: suitable in stock, see ID 35086 -Transport dimensions: 1180/150/H460 mm Djb Hjv U Tr Djhu Uzocg -Weight: 11 kg/piece

Condition: good (used), Underframe for conveyor belt, belt conveyor, conveyor belt, belt conveyor, belt conveyor, flat belt conveyor, roller conveyor, roller conveyor stand -Base: height adjustable -Type: Width 1180 mm -Height: 660 mm, adjustable -Number: 8 trusses available -Price: per piece -Roller conveyor: suitable in stock, see ID 35086 -Transport dimensions: 1180/150/H660 mm Dcjb Hhjv U Tm Ieu Uzog -Weight: 12.5 kg/piece

Condition: good (used), Underframe for conveyor belt, belt conveyor, conveyor belt, belt conveyor, belt conveyor, flat belt conveyor, roller conveyor, roller conveyor stand -Base: height adjustable -Type: Width 1180 mm -Height: 570 mm, adjustable -Number: 11 trusses available -Price: per piece -Roller conveyor: suitable in stock, see ID 35086 -Transport dimensions: 1180/150/H570 mm Dcobov U Tkge Hhu Uzjg -Weight: 12 kg/piece