PET filling line for nonreturnable bottles

KHS

Condition: used, Year of construction: 2007, Overview This KHS Innoclean single-end bottle washer for returnable glass bottles was built in 2007. It cleans and de-labels empty bottles before filling: bottles are pushed into carrier-basket cells, run on heavy roller chains through a pre-soak, two pre-warming baths, the main caustic soak with under- and over-caustic label flushing, and three water spray zones, then handed back onto the bottle conveyor at discharge. Nineteen bottles run across the machine width in 4,275 cells; output range and design output are given below under Technical data. At design output, total dwell time is 18.7 minutes, including 10.8 minutes of caustic contact. KHS modernised the drive and operator station in 2022: Triple-i-Drive and a capacitive multi-touch panel with RFID login, detailed under Equipment. A KHS manual supplement dated November 2022 covers the upgrade. Technical data - Manufacturer: KHS - Model: Innoclean - Machine type: single-end bottle washer (soaker) - Year of manufacture: 2007 - Drive and control modernisation by KHS: 2022 - Output range: 2,800 - 14,500 bottles/h - Design output: 13,200 bottles/h, 0.75 l glass bottle, 0.68 kg - Bottles across machine width: 19 Pjdpfx Aozzz Ivsppegt - Carrier baskets: 225, of which 217 loaded - Cell pitch: 105 mm; carrier chain pitch 169 mm - Bottle diameter: 54.0 - 89.5 mm (plastic cells) - Bottle height: 180 - 340 mm - Bath volumes: main caustic soak 23.0 m³, pre-soaks 0.9 and 1.1 m³, after-caustic 0.3 m³, spray zones 0.4 m³ each - Power supply: 400 V, 50 Hz, TN-S, 113 A nominal, 125 A slow fuse; control voltage 24 V DC - Water consumption: 3.56 m³/h, 270 ml per bottle - Compressed air: 1.0 Nm³/h at 3 bar - Overall dimensions: 11,040 x 4,470 x H 3,438 mm (incl. infeed table) - Conveyor heights: infeed 720 mm, discharge 1,690 mm - Weight approx.: 33.5 t machine, 62.6 t operating - Largest transport segment: 4,410 x 4,100 x 3,370 mm, approx. 7.3 t - Enclosure type 12; CE marked Equipment - Triple-i-Drive: worm gearboxes with individual geared motors, each on its own servo inverter with synchronisation and individual overload protection - Servo-driven infeed and discharge segments with brake motors - Capacitive multi-touch operator panel, graphical interface with component views, RFID card reader - Gearbox monitoring with torque protection - Two pre-warming and main caustic immersion baths, with under- and over-caustic label flushing and bottle base spray-off - Automatic label discharge over a full-width sieve belt with brush take-off - Automatic level control and caustic dosing; sieve tub filtration and after-caustic circuit for long caustic service life - Three water spray zones, internal and external, with rotating fresh-water spray - Vapour extraction and plate heat exchanger - Siemens SIMOTION D and SINAMICS drive cabinet - Original KHS documentation: operating manual, 2022 supplement, spare parts list Condition Used, technically complete. Still installed and under power at its production site; photographs and video show it running. Availability Immediately. The machine will be dismantled and relocated to Germany. Viewing by arrangement; dismantling, loading and transport can be quoted on request.

Condition: used, Year of construction: 2000, functionality: fully functional, total width: 1,150 mm, total length: 1,120 mm, total height: 2,400 mm, warranty duration: 3 months, empty load weight: 1,360 kg, Used vertical Atlas / Sabroe V316 AFT flake ice machine. Complete with 1 ICME T71B4 - 50 Hz - 0.37 kW - 1380 RPM electric motor and a control panel. The Sabroe V316 AFT produces between 8,000 and 19,000 kilograms of flake ice per 24 hours. The machine can produce different ice thicknesses by adjusting the speed of the rotating drum. Weight: 1,360 kg. Specifications Brand: Sabroe Type: V316 AFT Capacity: 8,000 to 19,000 kg/24h Refrigerant: Ammonia or Freon Dimensions: 1120x1150x2400 mm (LxWxH) Pgedev Uba Njpfx Appst Year of manufacture: 2000

Condition: used, Year of construction: 2018, operating hours: 3,500 h, machine/vehicle number: LC636, Used filling KHS Innofill can line 16000 CPH - year 2018Technical Specifications & Performance DataThis complete used bottling line is a second hand beverage canning system engineered around a KHS can filler block, integrated with high-quality upstream and downstream packaging machinery. Designed for industrial packaging and beverage production, it delivers reliable performance for aluminum cans.Production speed: up to 16000 cph (cans per hour)Primary filler: KHS Innofill Can C (2018)Can seamer: Ferrum FC03 (2018)Depalletizer: SKA Fabricating Can-I-BusInspector: Heuft fill level detectorRinser: AV-C500 can air rinserDryer: Air Control Industries can dryerLabeller: Pack Leader (Advanced Dynamics system)Case packer: Atlanta Rafaello 726Case coding: SATO S86-EX printerConveyors: KHS and AE Conveyors, plus KBR outfeed belt conveyor with PCUtilities/auxiliaries: Conveyor lubricator (Loewados)Container type: Aluminum cansDocumentation: Hard‑copy manuals includedAdvanced Automation & Control SystemsThe line is equipped with dedicated control cabinets for conveyors and labeling, supporting coordinated start/stop logic and smooth product handling. The KHS Innofill Can C filler block provides modern automation architecture with line-friendly integration, recipe handling, and synchronized drives for consistent filling and seaming operations. Safety interlocks and guarding are present across key stations for operator protection and process reliability.Production Line Integration CapabilitiesThis packaging line offers end-to-end integration from depalletizing to case packing, enabling seamless flow of cans through rinsing, filling, seaming, inspection, drying, labeling, and secondary packaging. Modular conveyors by KHS, AE Conveyors, and KBR facilitate balanced accumulation and stable transfer, helping maintain throughput at rated speeds. The configuration is suitable for a wide range of beverage production scenarios and can be adapted to different aluminum can sizes with appropriate change parts and guides.Machine Condition & Maintenance HistoryAs a second hand used bottling line, the core process equipment includes 2018-generation KHS Innofill Can C filler and Ferrum FC03 seamer. The asset list indicates a complete, coherent set of stations with hard‑copy manuals available, supporting efficient commissioning, maintenance, and spare parts management. The line is presented in working condition and ready for operation, subject to standard site preparation and utilities.Operational Performance & VersatilityDesigned for high-efficiency can handling, the line features a SKA Fabricating depalletizer for automated infeed, an air rinser for internal container preparation, precise isometric filling via KHS Innofill Can C, and robust double seaming with the Ferrum FC03. Quality assurance is enhanced by a Heuft fill level detector. Downstream, an Air Control Industries dryer pre... Pgsdpfx Aoy Szbyeppot

Condition: excellent (used), Year of construction: 2015, KHS INNOFILL DVD 40 CAN FILLING LINE MAX SPEED: 34,000 CPH 330ML IN 24 PACK WRAPAROUND CARTON CURRENT SPEED: 24,000- 28,000 CPH IN SMALL WRAPAROUND CARTON 4/6/8/10/12 PACKS LOCATION: UK STANDARD CAN 330ML & 440ML LID 202 SLEEK CHANGEPARTS FOR FILLING BLOC AVAILABLE GPI PACKER ADDED IN 2018 ROBOPAC PACKER ADDED IN 2022 EQUIPMENT LIST: FIPAL MINIDEPAL 20 LA DEPALLETISER • TWIN LANE RINSER • KHS INNOFILL CAN DVD 40 FILLING BLOC 34,000 CPH Podpfx Apetraaaopogt • FERRUM F6 6 HEAD SEAMER • CSW DEVENTER LID FEED SYSTEM • HEUFT SPECTRUM TX • EURO SISTEMI CAN DRYERS • TELEDYNE TAPTONE INSPECTION • ROBOPAC PRASMATIC TC400 COMPACT CASE PACKER • FT SYSTEM CP600 TP TUR300 Z200 RAS001 • GPI QUICKFLEX 300 MULTI-PACKER • HITACHI INK JET PRINTER • PACKITAL LANER • COMPLETE CONVEYOR SYSTEM • FIPAL PAL 80 F PALLETISER • ATLANTA STRETCH REVOLUTION LS STRETCH WRAPPER LOCATION: UK VIEWINGS BY APPOINTMENT WELCOME. PLEASE GET IN TOUCH TO ARRANGE AN INSPECTION. INDASSOL.COM

Condition: used, Year of construction: 2022, Overview The rotary filling and capping machine manufactured by Bertolaso in 2022 is currently used for vinegar production. It features 30 filling valves and 4 capping stations and operates based on the atmospheric filling principle. The machine can be used with a wide range of shape-stable containers and is suitable for filling low-viscosity, non-carbonated liquids. Technical details:  Filler: 30 valves (Ø16 mm), model Olimpia 30/1050 Capper: 4 Pick & Place heads, model Sigma P&P 4/350 Bottles: 600 ml & 1000 ml cylindrical (range Ø55–95 mm, H160–360 mm) Caps: Pre-threaded plastic Pgodpfx Aexqz D Ajppot Output: 8,000 bph (600 ml) / 6,000 bph (1000 ml) Material: All product-contact parts in AISI 316 stainless steel Bowl: Electrically height-adjustable, mechanical float level control Features: - Automatic valve opening/closing - Centralized fill-level adjustment (±50 mm) - Maintenance-free lifting cylinders - Automated lubrication system - Integrated washing/CIP system - Remote teleservice via Ethernet Safety: CE compliant, transparent guards with microswitches Includes: Format parts for 600 & 1000 ml bottles; adjustable star wheels (+/- Ø55-95mm)  

Condition: excellent (used), 2 x KHS / GEA High Speed Keg Filling Lines Pjdpfx Apexcinmopjgt Capacity: 1,000 kph Sizes: 15L, 20L, 30L, 50L 60L Keg Palletiser System also available. Location: Dublin Please contact Indassol for further details & pricing.

Condition: used, Year of construction: 1992, Overview This complete automatic can filling line has a nominal output of approx. 20,000 cans/hour for 330 ml cans (can type 211/202), packed 24 cans per foil-shrunk tray. The core is an O+H / KHS Hansacan filler with 30 filling valves, mechanically blocked to a Ferrum F 505 G seamer with 5 seaming heads. Empty cans are supplied by a TMG Impianti Vega 120/B depalletizer and rinsed on a Hysek Rinsstar 20000 rinser before filling. A date/coding printer is not included. Technical data Pjdpfx Aezlqu Tjppogt - Line type: Complete automatic can filling line - Nominal output: approx. 20,000 cans/hour (330 ml), product- and temperature-dependent - Container: 330 ml can, can type 211/202; 24 cans per foil-shrunk tray - Controls: PLC Siemens S7, Siemens SIMATIC HMI - Warmer and drying station reconditioned; fill-height control and packaging machine new Equipment - Can Depalletizer | TMG Impianti | Vega 120/B | tier-sheet removal, can table, pallet magazine | 2014 - Can Rinser | Hysek | Rinsstar 20000 | filtered-water rinse | 2001 - Can Filler | O+H / KHS | Hansacan | 30 filling valves, fixed for can type 211/202, will be general overhauled | 1992 - Can Seamer | Ferrum | F 505 G | 5 seaming heads, blocked with the filler | 2010 - Can Warmer | SMB | stainless-steel tunnel | warms cans to approx. 25 °C before packaging | reconditioned - Fill-Height Control | Heuft | incl. pushing/reject station | new - Can Drying Station | Gesete | air-dries cans before coding | reconditioned - Packaging Machine | Termo Pack | UMT-1500 | tray erector, packer and foil shrink | new - 2x can turning stations (330 ml can) - Can conveyor system incl. electrical control panel (PLC Siemens S7) - Tray conveyor system incl. drive station Condition Used line delivered in reconditioned or new condition. The filler and Ferrum seamer are reconditioned and blocked as one unit with a new electrical panel (PLC Siemens S7), new pneumatic panel and renewed pneumatic valves; the can warmer and can drying station are reconditioned; the fill-height control and packaging machine are supplied new. This work is carried out as part of the order, so the line is supplied component by component and is not yet assembled or tested as one running unit. The can depalletizer is the exception - it is already fully reconditioned and in stock. Filler and seamer are delivered with CE declaration and full documentation. Components can be inspected on request. Availability On request; delivery time as per agreement. Reconditioned and new-build components are supplied with a lead time after order. Location and inspection on request.

Condition: used, Year of construction: 1992, Overview This O+H / KHS Hansacan can filler, blocked with a Ferrum can seamer, is a rotary can filling and seaming monoblock for beverage cans. Filler and seamer are joined as a single unit, so cans run from filling straight through to seaming in one continuous flow. The block is set up for standard 330 ml cans (can type 211 / 202) and reaches a rated output of approximately 20,000 cans per hour, depending on product and filling temperature. The block was previously in production in a commercial brewery filling 330 ml cans and is currently at the workshop undergoing a complete reconditioning before delivery. Filling parameters and production data are managed via a Siemens SIMATIC touch HMI, with machine control on a Siemens S7 PLC. Technical data - Manufacturer: O+H / KHS - Model: Hansacan can filler - Seamer: Ferrum can seamer, F 505 G - Year of manufacture: filler 1992, seamer 2010 - Machine type: rotary can filler and seamer monoblock - Filling valves: approx. 30 (type Hansacan) Psdpozlqu Hefx Appjgt - Seaming heads: 5 - Capacity: approx. 20,000 cph at 0.33 L (product- and temperature-dependent) - Can format: 330 ml standard cans, can type 211 / 202 - Products: beer, carbonated beverages - Control: Siemens S7 PLC with Siemens SIMATIC touch HMI Equipment - Filler and seamer supplied as one blocked unit - New electrical panel with Siemens S7 PLC and SIMATIC touch HMI (reconditioning scope) - New pneumatic panel with renewed pneumatic valves (reconditioning scope) - Beer regulating valve ahead of the beer inlet, CIP tulips and CO₂ injection before seaming - Set up for can type 211 / 202, 330 ml - Manuals, spare-part list and electrical documentation for filler and seamer (provided with the machine) - CE declaration to be issued on completion of reconditioning Condition Used - currently undergoing a complete reconditioning at the workshop and to be delivered fully overhauled, supplied as a blocked filler and seamer unit. The reconditioning scope and the CE declaration are committed as part of the sale and are not yet complete. The block was previously in production in a commercial brewery filling 330 ml cans. Availability On request, after completion of the reconditioning. Location and firm delivery date on request.

Condition: used, Year of construction: 1992, Overview This carbonator was manufactured in 1992 by Germany KHS. The KHS CX 30 is designed for the production of carbonated mineral water. The unit was upgraded by KHS in 2014 and has a capacity of up to 30,000 litres per hour. The machine was in production until March 2025, was dismantled in December 2025, and is currently stored in a warehouse in Bippen. The machine is available immediately. Technical data - Capacity: 30,000 litres/hour - Application: Carbonated mineral water - Configuration: Carbonator with pumps, tank, and accessories - CO₂ rate: max. 8 g/litre - Drive: Siemens S7 Scope of Delivery - Carbonator | KHS | CX 30 | 1992 (upgraded 2014) | Complete system - Pump system  - Tank | KHS  - Control system | Siemens | S7  Pjdjzavp Hspfx Appsgt

Condition: used, Year of construction: 2018, Overview This compact automated can filling line was manufactured with main equipment from KHS, Ferrum, Ska Fabricating and Atlanta. The line is designed for beverage can production and includes depalletizing, can transport, ionized air rinsing, filling, seaming and downstream film / shrink packaging. The core of the line consists of a KHS Innofill Can C filling system combined with a Ferrum FC03 can seamer. The system is integrated with overhead and floor-mounted can conveyors and is arranged in a compact production layout. Technical Data Pgsdpfey Tt H Dox Appjt - Manufacturer / main equipment: KHS / Ferrum / Ska Fabricating / Atlanta - Line type: Automated can filling line - capacity: 15.000/h - Number of filling valves: 21 - Number of seaming heads: 3 - Container type: 330ml, 440ml, 500ml standard can - Packaging type: loose cans into 12 & 24 trays and WA boxes - Year: 2018 - Operating hours: 3,446 h - Layout: compact canning line layout with overhead and floor-mounted conveyor sections Scope of Delivery - Can Depalletizer | Ska Fabricating Co. | – | Enclosed depalletizing system with safety guarding | 2018 - Can Conveyor System | KHS / AE | – | Overhead and floor-mounted conveyor network for empty cans and line transfer | 2018 - Ionized Air Rinser | Ska Fabricating Co. | AV-C500 | Empty can rinsing / cleaning module before filling | 2018 - Can Filler | KHS | Innofill Can C | Automated can filling system | 2018 - Fill level detection | Heuft | - - Can Seamer | Ferrum | FC03 | Rotary can seaming unit | 2018 - Can dryer | Air control industries | 2018 - Labeller | Pack Leader Advanced Dynamics | Pro-516 | Labelling machine incl. roller feed | 2018 - Case Packer | Atlanta | Rafaello 726 | packaging system | 2018 - Case Packer Printer | SATO | S86-EX | 2018

Condition: used, Year of construction: 1999, Overview  This complete hot-fill and cold-fill bottling line was manufactured in 1999 – 2017 by Germany KHS and Krones. The line is designed for beverage production in glass and PET bottles, supporting both hot-fill and cold-fill applications. It was in operation until the end of 2025, is still installed, and is available immediately. The line can be inspected on request. Technical data  Psdpsyx I Awsfx Appsgt - Capacity: 12,000 – 36,000 bottles/hour (example: approx. 33,000 bph @ 500 ml) - Formats: 250 ml – 1000 ml - Application: Hot-fill and cold-fill beverage production - Container types: Glass bottles and PET bottles (hot-fill) - Filling temperature: 10°C – 104°C - CO₂ capability: Yes - Closures: - Glass: 28 mm aluminium, 33 mm / 43 mm aluminium twist-off - PET: 38 mm 3-start hot-fill closure - Labelling: Cold glue paper labels (optional sleeve labelling available) - Packaging: Wrap-around cartons and tray packaging (no shrink wrapper included) Scope of Delivery  - Depalletizer | Meypack | DL 71 | - | Low-level depalletizer with pallet conveyor and magazine - Bottle rinser | Niko | Linear Rinser | 1999 | Siemens S7 PLC, heat recovery system - Filler | KHS | Innofill DNR 80 | 1999 | 80 valves, 15-head aluminium screw capper, HMI renewed 2015 - Twist-off capper | Italmeccanica / Crown | S4BLH | - | Steam-heated, automatic cap feeding - Cooling tunnel | Tuchenhagen / Göbel | K1-135 | - | 7 cooling zones - Bottle dryer | Europool | - | 2007 | High-speed air dryer - Labelling machine | Krones | Starmatic | - | Cold glue labelling, Siemens S5 - Wrap-around packer | Kisters | 320/50 | 1999 | Tray and carton packaging, Nordson hot melt - Conveyors | KHS / Krones | - | - | Complete conveying system - Palletizer | KHS | LORD 1BSN2 | 1999 | Pre-grouping, pallet formats Düsseldorf/Euro/Industrial - Pallet labeller | Logopack | - | - | Pallet labelling system - Reverse osmosis system | MWT | - | - | Capacity 800 l/h

Condition: used, Year of construction: 2005, Overview  The palletizer was manufactured by the German company KHS in 2005 and was until recently part of a bottling line in German dairy company. The palletizer is now being released as the owner is sgutting down the production. Technical details/ scope - Worked with tray/cartons of 8 units (4x2) - Pallet loader - With shutter head - Incl. protective fences, pallet transport, tray transport, tray turner, formation table, empty pallet magazine Pgodpexb Ar Ajfx Appot