FEMIS d.o.o.

Condition: good (used), Year of construction: 1989, functionality: fully functional, working width: 500 mm, wire diameter (max.): 4.5 mm, We are offering this used Gensch GSA 2200 wire mesh welding machine, manufactured in 1989, in good condition. The mesh welding machine can process wire thicknesses from 3 to 5 mm. Iodpfezfgqqjx Acdsth Operating principle: The longitudinal wires, up to 6 pieces, are drawn from coils that unwind from spools into the welding portal. The transverse bars then fall from the magazine into the welding portal; the spacing of the transverse bars can be adjusted freely. The welding presses close, and the longitudinal and transverse wires are welded together. After the welding process, the CNC-controlled carriage advances the mesh mat step by step. At the end, the mat is cut, and any wire overhang is trimmed. Finally, the mat is stacked. The current working width is 50 cm. The length of the mesh can be freely selected from 20 cm to 200 cm. If you have any questions or need more information, please send us a message or call us.

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, working width: 1,650 mm, wire diameter (max.): 7 mm, Schlatter MG930, quick change, DC welding machine with 5 DC transformer, 1092 kVA. Schlatter control from 2007 with S7-300 PLC. Automatic line wire loader up to 3m, automatic line wire channel positioning, open portal DC welding machine, quick change cross wire hopper, MLV1 pullout and stacker. Itedpfx Acezd Sulsdoh

Condition: used, Year of construction: 2004, functionality: fully functional, working width: 1,700 mm, wire diameter (max.): 6 mm, type of input current: three-phase, Basic Information Number: 13921 Control System: Siemens S7-400 Technical Details Materials processed to date: bare and galvanized wires Intended use: Production of fencing and industrial mats Technical condition: The system was in production until January 5, 2026, disassembled and stored Longitudinal wire diameter min: 2 mm Longitudinal wire diameter max: 6 mm Transverse wire diameter min: 2 mm Transverse wire diameter max: 6 mm Cycles (transverse wires) min/max: 120 Maximum mat width: 1700 mm Longitudinal wire feed: pre-aligned rods Transverse wire feed: pre-aligned rods Longitudinal wire spacing min: 25 mm Transverse wire spacing min: 12.5 mm Transverse wire spacing max: 1500 mm Number of welding transformers: 8 Number of welding presses: 41 Maximum welding width: 1600 mm Maximum mat length: 3000 mm Mat cutting shear: present Mat stacker: present Transverse wire magazine: present Drive power: 122 kVA Total connection power: 900 kVA Operating voltage: 3x400 V Frequency: 50 Hz Control voltage: 230 / 24 V Electrical cabinet: present Additional data: The system consists of: GRID WELDING MACHINE IM-QC/72 Longitudinal wire MAGAZINE Longitudinal wire DISTRIBUTOR Longitudinal wire FEEDING MACHINE IM-ZL/72 Strip and EDGING MACHINE Q 5H/72 MAT CUTTING SHEAR L 1/72 MAT TRANSPORTER LT-PV/72 MAT STACKER SHR/72 Ijdpfezb Nx Rex Acdoth

Condition: ready for operation (used), Year of construction: 1995, functionality: fully functional, Articulated arm grinding machine for granite and marble Completely overhauled in 2015 S2H oscillating head Pneumatic pressure control Excellent condition! Isdpfx Aoy Ufkdjcdoth Superbly maintained and cared for! Drive motor with speed control for perfect grinding results in granite and marble. If interested, a test grinding can be carried out after prior arrangement.

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, working range: Iedpfx Acjy Er Uqedjth X-axis: 2.000 mm Y-axis: 1.200 mm Z-axis: 190 mm welding power: 20 kA welding force: 2 x 5 kN

Condition: good (used), Year of construction: 2020, functionality: fully functional, working width: 3,700 mm, welding power (max.): 2,200 kVA, wire diameter (max.): 25 mm, type of input current: three-phase, 1. EVG QC76/144-ZL/PV Wire Mesh Welding Line Description EVG High-Performance Mesh Welding Line - Type QC76/144-ZL/PV · Max. Sheet Width: 3,700 mm (Welding width: 3,600 mm) · Sheet Length Range: 1,500 mm – 12,000 mm · Wire Diameter Range: Line wire (6 – 25 mm) / Cross wire (6 – 16 mm) · Max. Working Speed: 90 CW (cross wire) / min. · Line Wire Spacing: 75 mm – 1,000 mm (Steplessly programmable) · Cross Wire Spacing: 50 mm – 2,000 mm (Steplessly programmable) · Number of Line Wires: Max. 33 wires · Input Material: Pre-cut and straightened line and cross wires (Cold-formed/Hot-rolled) · Power Rating: 2,200 kVA (Driving power: 120 kW) Key features · Versatility: Optimized for the economic production of special sheets and engineered fabric, even for the smallest lot sizes. · Precision: Features steplessly programmable spacing for both line and cross wires, allowing for highly customized mesh designs. · Heavy-Duty: Capable of welding large diameter wires (up to 25 mm), suitable for structural and industrial applications. · Automation: Advanced cascade welding system (automatic) for efficient multi-diameter operations. 2. EVG DRE16 Wire Straightening Machine Description EVG DRE16 High-Speed Wire Straightening and Cutting Machine · Wire Diameter Range: 8 mm – 16 mm Iedey Aig Sopfx Acdoth · Max. Feed Speed: 160 m/min. · Max. Wire Strength ($Rp0.2): 600 N/mm2 · Driving Power: 85 kW · Power Supply: 380 V, 60 Hz, 3ph · Color: RAL 7001 (Grey) / RAL 3011 (Red) · Standard Compliance: EN 60204-1, IEC 60364-4-41 TN-C Key features · High Productivity: Offers a superior straightening speed of up to 160 m/min, ensuring high throughput for downstream welding lines. · Material Compatibility: Specifically designed to handle high-strength wire up to 600 N/mm2. · Reliability: Built with EVG’s renowned precision engineering for consistent straightening quality and long-term durability. * Machine can be seen in factory.

Condition: excellent (used), Year of construction: 2013, PRATTO equipment for zinc coated welded meshes Technical data for the machine : STARWELD PE is a high-performance mesh welding line for the production of fine & light mesh in rolls or rolls & sheets • 2 pay-off for feeding the cross wire • 36 pay-off for feeding the line wire Iodeyxn Rnopfx Acdsth • Fence dimensions between 1 and 3 m (2 types can be made simultaneous, example 1 m with 2 m, 1.5 m with 1.5 m, 1.2 m with 1.8 m) • Range of wire diameter 1.2 – 3 mm • Working speed (strokes/min) Up to 130 • Automatic stacking of rolls • ⁠PLC management

Condition: like new (used), Year of construction: 2021, functionality: fully functional, working width: 1,700 mm, welding power (max.): 600 kVA, wire diameter (max.): 6 mm, type of input current: three-phase, MG950 Mesh Width (Cross Wire Length) for lower feed, single-row: 200 – 900 mm for upper feed, single-row: 200 – 1700 mm for upper feed, double-row (usable width): max. 1530 mm Mesh Length: max. 3200 mm min. 350* mm Distance between the outermost longitudinal wires: max. 1600 mm Longitudinal wire pitch: min. 20 mm Cross wire pitch: min. 10 mm steplessly programmable Clear opening longitudinal wire: min. 15 mm Clear opening cross wire: min. 8 mm Longitudinal wire diameter: 2.0 – 6.0 mm Cross wire diameter: for lower feed: 1.5 – 4.0 mm for upper feed: 2.0 – 6.0 mm Longitudinal wire overhang: max. 300 mm, min. 10 mm Cross wire overhang: max. 300 mm, min. 5 mm Number of individual welding groups ESG: 12 Itjdeym An Aepfx Acdeh Number of portal welding groups PSG18: 12 Max. number of longitudinal wires: 12

Condition: used, Automatic rebar mesh welding machine MCC001 The machine is designed for welding steel reinforcement mesh from previously shortened reinforcements for rods that comply with the EN 10080 standard. Technical data: Diameter of reinforcing bars: 4mm, 5mm, 6mm Number of longitudinal bars: 2 – 12 Length of longitudinal bars: 200mm – 3000mm Minimum step between longitudinal bars: 100mm Pitch of crossbars: 10mm – 999mm Length of crossbars: 100mm – 1250mm Screen moving speed: 0.1m/s – 1m/s Compression force: 60kg – 190kg Productivity: 1 cycle/minute Electricity: Supply voltage: 400V Voltage frequency: 50Hz Connection type: TN-C Power: 100kVA Higher engine power: 0.8 kW Power of one welding transformer: 35 kVa Iodpsymcpysfx Acdjth Pneumatic indicators: Working medium: Compressed air Working pressure: 6 bar Air consumption: 250 l/min Cooling: Cooling type: water cooling Circulation type: forced circulation Maximum incoming heat carrier temperature: 35 °C Heat carrier consumption: 60 l/min Diameter of reinforcing bars: 4 mm, 5 mm, 6 mm Number of longitudinal bars: 2 – 12 Length of longitudinal bars: 200 mm – 3.000 mm Minimum step between longitudinal bars: 100 mm Pitch of crossbars: 10 mm – 999 mm Length of crossbars: 100 mm – 1250 mm Screen moving speed: 0.1 m/s – 1 m/s Compression force: 60 kg – 190 kg Productivity: 1 cycle/minute Supply voltage: 400 V Voltage frequency: 50 Hz Connection type: TN-C Power: 100 kVA Higher engine power: 0.8 kW Working medium: Compressed air Working pressure: 6 bar Air consumption: 250 l/min Cooling type: water cooling Circulation type: forced circulation Heat carrier consumption: 60 l/min

Condition: used, EVG G95 Reinforcing mesh welding line 2.5x6m Welding lines for the efficient production of standard reinforcing mesh in medium to large lot sizes Isdpfx Acjymb Unodeth - Automatic and highly dynamic feeding of wires from coils - Top production speeds on single-step welding lines - Double point welding is perfect technology for thicker wire diameters Scope of supply: Full machine including stands Optional: Fixed spools up to exit conveyor Technical data: Diameter line and cross wire: 5 – 12 mm Line wire spacing: 100, 150, 200 mm 36 horizontal line wire stands for 3Ton reel Cross wire switch with doubles horizontal pay offs Tying and mat lift machine not included Diameter line and cross wire: 5 – 12 mm Line wire spacing: 100, 150, 200 mm 36 horizontal line wire stands: for 3Ton reel Cross wire switch: with doubles horizontal pay offs

Condition: excellent (used), functionality: fully functional, welding power (max.): 180 kVA, Schlatter Posiweld type Libra. Machine was built in 2005, control was upgraded by Schlatter in 2022. Iodpsxlvn Eefx Acdsth

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Iodpfx Acswu Tu Dedsth Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: refurbished (used), Year of construction: 2025, JAGER welded mesh line U-Gsa-st Full revamped "as new" Technical data 24 pay off for longitudinal wire spools, longitudinal wire straightening equipment Line wire pull off system Isdswu Dcxopfx Acdoth Longitudinal wire loop Longitudinal wire straightening equipment Cross wire magazine Number of installer line wires : 24 up to 10 mm Diameter of lines wires : 4 to 10mm Diameter of cross wires : 4 to 10mm Separation between line wires : 100, 150, 200, and 300 mm Separation between cross wires : min 30 mm , steplessly programmable Max. length of cross wire (mesh width) 2500 mm , max welding width : 2400 mm Mesh length : min 3000 mm and max . 6000 mm Trafos : 8 x 160 Kva Number of installer line wires: Number of installer line wires : 24 up to 10 mm Diameter of lines wires: 4 to 10mm Diameter of cross wires: 4 to 10mm Separation between line wires: 100, 150, 200, and 300 mm Separation between cross wires: min 30 mm , steplessly programmable Max. length of cross wire (mesh width): 2500 mm Max welding width: 2400 mm Mesh length: 3000 - 6000 mm Trafos: 8 x 160 Kva

Condition: excellent (used), Year of construction: 1992, Manufacturer EVG Type TSD 7-25 Machine No. 958 Year of manufacture 1993 Working direction L > R Beam types KT 8… Beam height (mm) 90-250 Carrier length min. (mm) max. (mm) 14,000 Fixed lengths: Yes Cutting pitch (mm) 100/200 Spool unwinder (pcs.) 5 LAR: Yes Wire diameter - 5-12 mm smooth/ribbed Itedpjwp Ilyefx Acdsh Diagonal - 4-7 mm smooth / ribbed Stack height max. (mm) - 500

Condition: excellent (used), Technical Details : Isdpfx Aoryv S Uscdsth Year of manufacture: 1985 (fully electric in 2007, partial in 2010 underwent a mechanical overhaul.) The mesh max. width: 1500 mm Mesh density: 15 welding heads in arbitrary distribution Increment: 20mm – 200mm. Wire thickness: 1.2mm - up to 2.2mm (max 650 N/nmm - We have already welded 2.5mm also wired.) Energy demand: 14 kVA (max) Weight: approx. 8 tons Drive: digital servo, control (PLC). Stepless regulation.. Accessories: manual

Condition: excellent (used), Year of construction: 2004, Technical Details : Year of manufacture: 2004 The mesh max. width: 2200 mm Mesh density: 20 welding heads in arbitrary distribution (40 heads are also possible) Increment: 20mm - up to 200mm Ijdoryv Sispfx Acdsth Wire thickness: 1.6mm-3.0mm (max 550Nnmm) Energy requirement: 8 kW Weight: approx. 10 tons Drive: digital servo, control (PLC).. Stepless regulation.. Accessories: manual

Condition: excellent (used), Year of construction: 2009, Technical Details : Year - 2009 Beam welding machine outlet height: 1400mm (UK beam from ground) Min. strap length: 0.8 m Max. beam length: 16.0 m Base width during production: 58 mm (inside diagonals) Finished beam width: 70 – 116 mm (external dimensions of bottom chords) Lattice girder production speed: max. 15 m/min Design of the wire feed speed: 18 m/min (upper and lower belt) Iedjrn N Efopfx Acdoth 38 m/min (diagonals) Carrier types that can be produced: KT KTS Top belt Ø: 5 – 16 mm 5 – 7 mm Lower belt Ø: 5 – 16 mm 5 – 7 mm Diagonal Ø: 4.5 – 9 mm 5 – 7 mm Height: 70-400mm 80-310mm Division of the diagonal: 190 – 210 mm 200 mm Primary material: Cold or hot rolled reinforcing steel from coil in accordance with EN 10080:2005 in weldable quality, max. carbon content 0.20 % The line is in excellent working condition !

Condition: excellent (used), Year of construction: 2003, working width: 215 mm, welding power (max.): 750 kVA, Complete Mesh welding/Lattice girder factory Factory consists : - Mesh welding line SCHLATTER PG 24 , Semi- automatic , Year - 2002 - Lattice Girder Line SMEI , Full automatic , Year - 2003 - Straightening and cutting machines 1x Wafios R4 2 x VITARI NR16 Ijdpfxeqy Ek Aj Acdsth 1X VITARI NR10 - Cold drawing line SMEI , Input wire max.10mm, Speed - 4m/sec. - But welding achine SMEI - Wire sharpener SMEI

Year of construction: 1978, condition: excellent (used), Technical details : -Manufacturer- DRAWEBA - Model - DDANS 17 l - Year - 1978 - Wire Diameter - 1,4 -1,6 mm - Mesh opening size - 10x10 mm min. Isdpelf Iqnjfx Acdeth - Mesh width - 1600 mm

Condition: new, Year of construction: 2025, Features: Line & cross wire feeding from pre-straightened and cut bars Automatic feeding of cross wires from hopper Manual feeding of line wires Automatic Panel stacking Excellent mesh accuracy Fully or semi-automatic CNC programmable High speed High precision through advanced servo technology Easy machine adjustments Easy maintenance & use High reliability & long life Iedpfef Ar N Uox Acdsth

Year of construction: 2010, condition: excellent (used), Technical Details : - For sale Full automatic mesh welding line PITTINI / EVG - Mesh width - max. 2400 mm - Mesh length - max. 8000 mm - Dia. Longitudinal wire - max. 10 mm - Dia. Cross wire - ma. 10 mm Itsdpfx Acefwm D Todeh - Max. number of longitudinal wire - 24 - Longitudinal and cross wire from spools - Cross wire feeding unit - EVG - Speed - max. 110 tacts / min. - installed power - 1,5 Mw - Automatic mesh packing unit

Year of construction: 1990, condition: excellent (used), Technical Details : – Year – 1990/2012 – Model – 8/SR12 – Speed – max. 70 tact/min. – range of opening mesh space – 25×25 – 100×100 mm – Wire range – 1,5 – 5 mm – Number of transformers – 4 x 100 kw – Mesh width – max. 1200 m Itedpjd Sfgbefx Acdsh – Mesh lenght – 1000 – 3000 mm On line was made new control panel and transformers in 2012

Condition: new, Year of construction: 2025, STARWELD GR is a high performance mesh welding plant for the production of electro-fused grating. A big product range can be achieved through its easy adjustments. Special designs can be adopted according to the customer needs (special technical specifications or special products). Itodpfx Acod Rlapedoh Products can be used for stairs, floorings, catwalks, platforms, fencing, etc. Features: Feeding from coil or pre-straightened and cut bearing bars Automatic or manual feeding of flat steel bearing bars Automatic feeding of round or twisted-square cross bars from coils or hopper Various bearing bar spacings: 22, 25, 30, 34 mm or different on demand Very effective grating flattening mechanisms Cross bar automatic edge trimming Fully automatic CNC programmable High speed High precision through advanced servo technology Easy machine adjustments Easy maintenance & use High reliability & long life

Condition: new, Year of construction: 2025, STARWELD POBH is an advanced version of our high-performance mesh welding line, designed to produce high-quality wire mesh 3D fences, including Eurofence and “V”-shaped fence designs. This model is equipped with a bending unit that allows for precise shaping of wire mesh, making it an ideal choice for various fencing projects. Bending Unit: The integrated bending unit empowers STARWELD POBH to effortlessly shape wire mesh into Eurofence or “V”-shaped fence patterns with precision. This feature enables you to meet the demands of diverse fencing projects with ease. High-Quality Output: Expect nothing less than exceptional quality from STARWELD POBH. Whether you’re crafting aesthetically pleasing Eurofences or robust “V”-shaped fences, our model ensures each piece meets the highest industry standards. Itjdpfx Aed Rlanecdsh Tailored to Your Needs: Just like its predecessor, STARWELD POH, this model is customizable to your specific project and mesh type parameters. We can adapt the design to suit your unique requirements, ensuring optimal performance and results. STARWELD POBH is not only ideal for the construction industry but also finds its utility in crafting shelves, grids, cages, pallets, containers, and, of course, fencing. Its ability to create intricate 3D fence designs makes it a standout choice for projects that demand both functionality and aesthetics. Elevate your wire mesh production capabilities with STARWELD POBH, where innovation meets precision to redefine the art of fence manufacturing. Contact us today to discuss how STARWELD POBH can transform your fencing projects into works of excellence.

Condition: new, Year of construction: 2025, STARWELD PO is a high performance mesh welding line for the production of medium & heavy weight wire or reinforcing mesh panels. It is a line appropriate for big production needs. Design is made in accordance to the specific project & mesh type parameters – e.g. there can be a rolling mechanism for the machine to produce rolls too if so desired. PRATTO can supply all the necessary auxiliary equipment. Products can be used in the construction industry. They are also used for shelves, grids, cages, pallets and containers as well as for fencing (plain & bent). Features: Line wire feeding from coil Cross wire feeding from coil Edge trimming (optional) Panel stacking (optional) Panel tilting (optional) Rolling mechanism (optional) Bending unit (optional) Excellent mesh accuracy Fully automatic CNC programmable High speed High precision through advanced servo technology Isdpfsd Rlalox Acdoth Easy machine adjustments Easy maintenance & use High reliability & long life