Minimum DOOEL

Condition: used, Year of construction: 1998, Bending Performance Steel Pipe 60x3 mm Bending performance for stainless steel 60x2,5 mm Bending performance with solid material 35 mm bending speed 2 U/min Itsdpeyv N Rdefx Abnjd Bending performance for hard copper and aluminum 64 x 4 mm bending radius max. R10-R300 mm total power requirement 1,5 kW weight of the machine ca. 130 kg ___;

Condition: new, 40 mm 8,5 U/min 120 mm roll diameter 152 / 162 mm engine output 1,1 kW connected load 400 V weight 395 kg Overall size 900x600x1100 mm Equipment / Accessories: - Two driven rollers - Manual delivery of the upper roller Itsdpfxeyv N A Te Abnod - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn different profiles are used

Condition: new, 95 mm Shaft diameter 30 mm Shaft revolutions 7 U/min roll diameter 132 mm Drive 0,75 kW weight 220 kg range L-W-H 530x900x660 mm Equipment / Accessories: Ijdpfx Absyv N A Henetd - Two driven rollers with grooved surface - Manual feed of the upper roller - working position horizontal and vertical (with tilting base) - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn different profiles are used e.g. Flat iron, T-iron, solid material etc.

Condition: new, bar material - diameter Ø 35 mm I-beam section - flat steel 60x10 mm L-beam 50 mm tube diameter max. Ø 60x2 mm square material 45x45x3 mm roll diam. toproll 162 mm roll diam. bottom roll 152 mm Shaft diameter 50/40 mm turning speeds 3,3 m/min total power requirement 1,5 + 0,75 kW weight 450 kg range L-W-H 1050x950x1450 mm Domestic equipments: - hydr. Delivery of the top roller - standard roller set Iedpfx Aoyv N Aasbnstd - side straightening rollers - Upper roll holder: 50.0 mm - Under roller diameter: 40.0 mm - Control panel

Condition: new, I-beam section - flat steel 80x20 (d1200) mm I-beam section - upend 80x25 (d2100) mm L-beam 50x50x6 (d1000) mm bar material - diameter 40 (d800) mm square material 60x60x3 (d4000) mm rectangle 80x30x3 (d6000) mm tube diameter max. 70x2 (d1600) mm tool adaptor 60 mm roll diameter 177 mm bending speed 6,4 m/min total power requirement 4 kW machine weight ab. 970 kg Overall size 1400x950x1450 mm Domestic equipments: - hydr. roller drive Iodpfxeyv Nwqj Abnjtd - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German

Condition: new, I-beam section - upend 100 x 20 (d 2100) mm tube diameter max. 100 x 3 (d 3000) mm L-beam 80 x 80 x 8 (d 2000) mm square material 50 x 25 x 2 (d 600) mm bar material - diameter 60,0 (d 1000) mm I-beam section - flat steel 120 x 30 (d 600) max. 140 mm tool taper 80,0 turning speeds 4,2 U/min weight 1600 kg dimensions 1240 x 1375 x 1540 mm Domestic equipments: - Welded steel structure (St-52) - Rollers are driven by 3 separate hydraulic motors - Stepless speed - Special steel gears - Shafts are made of special steel, hardened and ground - Manual lubrication - Guide rollers are hydraulically adjustable - Lower rollers are hydraulically movable up and down - Infinitely adjustable speed of the lower rollers, move after below and above - Digital display for lower rollers - Separate and movable control panel - Horizontal and vertical operation - Production quality certified according to CE, ISO 9001 - 2015, TSEK and TURQUM Iedpfx Ajyv Nnisbnetd Additional equipment: - hydraulically adjustable straightening rollers

Condition: new, round material 40 mm tube diameter 70x2 mm square material 80x30x3 mm L-beam 50 x 5 mm roll diameter 157 mm I-beam section - upend 50 x 15 mm I - beam section - flat steel 80 x 16 mm Shaft diameter 50 mm bending speed 2,95 m/min total power requirement 1,1 kW weight of the machine ca. 500 kg dimensions of the machine ca. 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground Itedpfx Asyv Nk Rjbnjd - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German

Condition: new, R10-R260 max. 210 ° 54x2 mm 42x2,5 mm 42x3,5 mm 30 mm bending speed max. 4 U/min Amount of programms 30x9 voltage dreiphasig 220-400 V total power requirement 1,1 kW dimensions of the machine ca. 1000 x 410 x 570 mm weight of the machine ca. 80 kg Accessories / equipment: Itodpfxsyv I Uhj Abnod - Machine structure: aluminum alloy - Base: welded steel - Standard accessories (including footswitch, operating instructions)

Condition: new, R10-R260 210 ° bending speed 2 U/min 1 1/4" x 3,5 mm einphasig - 230 V Itsdoyv I Tkspfx Abnjd drive motor 1,1 kW < 70 dB weight of the machine ca. 80 kg dimensions of the machine ca. 410 x 1000 x 570 mm Accessories / equipment: Hard copper and aluminum: 54x2 mm Steel tube: 42x3 mm Stainless steel: 42x2.5 mm Solid material: 30 mm Number of programs: 30 each 9 bends Control: Soft-touch control panel in 8 different languages Mobile by driving device The controller allows easy programming of the automatic cycle The controller is equipped with a system diagnostics and has a great language selection. Patented fast tool change system A single bending speed

Condition: excellent (used), Pipe bending machine Rothenberger system Bending capacity: 2 7 bending dies for pipes 3/8 - 1/2 - 3/4 - 1 - 1 1/4 - 1 1/2 - 1 3/4 - 2 Footprint: Width: 630 mm Iedpjyv A H Ejfx Abnetd Length: 680 mm Transport case dimensions: Width: 700 mm Depth: 300 mm Height: 360 mm Weight: 80 kg

Condition: new, bending speed 2.1 m/min Bending capacity - square 30x30 mm bending capacity - flat iron 80x15 mm Itjdpfjyvvrnex Abned Bending capacity - flat iron on edge 50x10 mm tube diameter 1" oder 60x2 mm Shaft diameter - upper 35 mm Shaft diameter - lower 30 mm total power requirement 0,75 kw range L-W-H 650 x 500 x 1300 mm weight 170 kg Standard features: - hardened special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working

Condition: new, L-beam 50x5 mm square material 50x40x3 mm I - beam section - flat steel 120x15 mm I-beam section - upend 60x10 mm round material Ø 35 mm tube diameter Ø 70x2 mm roll diameter 155 mm Shaft diameter 50 mm Ijdpfx Abeyvvnienotd bending speed 4,3 m/min total power requirement 1,5 kW weight 400 kg dimensions 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German

Condition: used, Year of construction: 2006, RASI S80.6L - Tube Bending Machine - Curve and mandrel bending of tubes and round profiles - Spiral bending of tubes - Includes tooling and documentation - Year of manufacture: 2006 Technical Data - Tube Ø x wall thickness: 82 x 2.6 mm - Max. section modulus: 12.7 cm³ - Min. tube Ø: 4 mm Iodpfx Asyvvk Dsbnetd - Outer bending radius: 228 mm - Inner bending radius: 34 mm - Min. bending radius: 1.5 x D - Max. bending angle (precision ± 0.1°): 195° - Return bending speed (programmable): 0 - 9.3 rpm - Forward bending speed (programmable): 0 - 6.6 rpm - Pressure die: fixed / following - Tool configuration: single-, double-, or triple-grooved - Bending direction: right - Feed speed (stepless): 0 - 60 m/min - Feed thrust (during bending steplessly adjustable) - Torsion speed (stepless): 0 - 60 rpm - Max. torsion angle (± 0.1°): unlimited - Max. tube clamping force: 8 t - Chuck diameter clamping range: 6.5 mm - Bending length: 3 - 6 m - Motor power: 11 kW - Operating voltage: 400 V / 50 Hz - Control voltage: 24 V DC - Machine length: < 7000 mm - Weight: approx. 2,500 kg

Condition: excellent (used), functionality: fully functional, Year of construction: 2018, control type: manual, degree of automation: automatic, actuation type: electric, pipe diameter (max.): 60 mm, pipe length (max.): 6,000 mm, tube wall thickness (max.): 5 mm, bending angle (max.): 180 °, input voltage: 400 V, input frequency: 50 Hz, Equipment: emergency stop, It is a machine from 2018 and we used very little. We can bend pipe from 18 mm - 60 mm Isdeyvhl Hopfx Abnotd Machine cost new 2018 was ca 45.000,00 EUR and tools was ca 55.000,00 so total was EUR 100.000,00

Condition: used, functionality: fully functional, Year of construction: 2021, operating hours: 5,265 h, machine/vehicle number: CV022100123, control type: CNC control, degree of automation: automatic, actuation type: electric, pipe diameter (max.): 32 mm, overall weight: 275 kg, input voltage: 415 V, input frequency: 50 Hz, type of input current: three-phase, Equipment: documentation/manual, We offer this used BLM E-TURN32 CNC Tube Bending Machine, year of construction 2021. The machine is in good working condition and has been maintained in an industrial workshop. It is available for inspection and ready for immediate sale. Machine model: E-TURN32 Serial number: CV022100123 Year of manufacture: 2021 Supply voltage: 415 V Number of phases: 3 Supply frequency: 50 Hz Total installed power: 11.5 kVA Breaking capacity: 35 kA Ijdpfsyuf A Esx Abnjtd Control voltage 1: 415 VAC Control voltage 1 frequency: 50 Hz Control voltage 2: 230 VAC Control voltage 2 frequency: 50 Hz Control voltage 3: 24 VDC Control voltage 3 frequency: Hz Weight: 275 kg If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: excellent (used), functionality: fully functional, Year of construction: 2021, operating hours: 3,408 h, control type: CNC control, degree of automation: automatic, actuation type: electric, pipe diameter (max.): 52 mm, type of input current: three-phase, Equipment: documentation/manual, BLM ELECT52B CNC Tube Bending Machine. Electric Servo-Controlled CNC Tube Bender - ideal for high precision production. Key features include electric servo-controlled bending for high precision, heavy duty industrial construction, high efficiency and repeatability for production runs, multi-axis bending capacity, suitable for steel, stainless steel, and aluminium tubing. Itjdpfx Ajyufp Sobnjd Machine is in good working condition and has been maintained in an industrial workshop. It is available for inspection and ready for immediate sale.

Condition: used, Year of construction: 1997, tube diameter / mm wall strength / mm bending radius min. / mm CNC wire bending machine ROBOMAC 206 Iodpfxeyt R Sij Abnjtd General information Machine designation: ROBOMAC 206 Manufacturer: LATOUR / NUMALLIANCE (France) Machine type: CNC wire bending machine / wire forming machine Year of manufacture: 22 December 1997 Serial number / registration: 9711026 CE marking: present Weight Machine weight: approx. 4000 kg Working range Wire diameter: approx. 2 – 6 mm Material feed: wire from coil (ring) Bending heads: 2 bending heads Max. wire strength: approx. 600 N/mm² Mechanical data Feed length / feed arm: approx. 600 mm Tools: interchangeable tools for different wire diameters Control: automatic wire bending control Machine dimensions (approx.) Machine depth: approx. 2000 mm Machine height: approx. 1720 mm Electrical power Electrical connection: approx. 6.3 kVA Typical areas of application - Wire bending parts - Wire hangers - Metal hooks - Springs - Technical wire moulded parts for industrial applications Disclaimer All information is provided without guarantee. No liability is assumed for the accuracy, completeness and up-to-dateness of the technical data.

Condition: ready for operation (used), A CNC tube welding system Weil Technology for longitudinal seam welding is available. Tube diameter range: 76mm-600mm, Tube length range: 250mm-1550mm, Material thickness range: 0.8mm-2mm, Welding process: Laser, Max. welding output: approx. 80pieces/h. Documentation available. An on-site inspection is possible. Itodjyttwnepfx Abned

Condition: ready for operation (used), Year of construction: 2011, A CNC 10 axis pipe cutting system HGG including a plasma source Kjellberg HiFocus 280i is available. Pipe diameter range: 30mm-330mm, max. pipe load: 20kN, max. pipe length: 13000mm, max. workpiece weight: 2000kg, max. cutting angle: 70°, max. plasma cutting current: 280A. Documentation available. An on site inspection is possible. Isdpfxeytgpdo Abnstd

Condition: good (used), Year of construction: 1978, control type: manual, actuation type: hydraulic, pipe diameter (max.): 33 mm, tube wall thickness (max.): 2 mm, working height: 800 mm, total length: 1,850 mm, total width: 1,000 mm, total height: 1,000 mm, power: 1.5 kW (2.04 HP), Conventional tube bending machine, with various bending tools Ø 20 ... 33.7 mm + 4KT 25x25 mm Iodpfx Absyr Rx Hsnetd

Condition: new, neu ca. 10 Wochen ab Auftrags Italien 106340 € 2009.83 € 150 mm 1000 mm 1900 mm 1475 mm 2700 kg 170 cm³ 150 x 7,1 mm 6" x 7,11 mm 150 x 9 mm 141,3 x 6,55 mm 141,3 x 6,55 mm 168,3 x 9 mm 168,3 x 9 mm 64 x 6 mm 88,9 x 3,65 mm 110 mm Itjdpjynmtlefx Abned 150 x 45 stehend, 150 x 6 mm 800 mm 100 mm 10 mm 1 U/min 15 kW TCPlus Control with 7“ Touchscreen Programmable bending speed for each individual bend Possibility to bend left and right Users manaul

Condition: new, neu ca. 8 Wochen ab Auftragse Itjdpfxjynmr Uj Abned Italien 39500 € 754.45 € 127 mm 850 mm 1200 mm 850 mm 720 kg 80 cm³ 127 x 7,1 mm 4" x 8,56 mm 127 x 7,1 mm 114,3 x 5,6 mm 114,3 x 5,6 mm 139,7 x 8,8 mm 139,7 x 8,8 mm 64 x 6 mm 88,9 x 3,65 mm 50 x 4 mm 90 mm 130 x 25 stehend, 130 x 6 mm 700 mm 36 mm 10 mm 0 - 0,75 U/min 3.5 kW digital read out for bending angle 4 hexagonal tool holders (40, 50 80 and 110 mm) Possibility to bend left and right Users manaul Tools on request

Condition: new, neu ca. 8 Wochen ab Auftragse Italien 29100 € 555.81 € 100 mm 500 mm Itedeynmr Ijpfx Abned 1200 mm 850 mm 480 kg 43 cm³ 100 x 6 mm 3" 1/2 x 4 mm 100 x 6 mm 100 x 3,6 mm 100 x 3,6 mm 114,3 x 6,3 mm 114,3 x 6,3 mm 114,4 x 6,3 mm 88,9 x 3,65 mm 100 x 5 mm 70 mm 100 x 25 stehend, 100 x 5 mm 400 mm 36 mm 10 mm 0 - 1,3 U/min 3.5 kW quick-change tooling system digital display of bend material spring back compensation remote control of bend, return and emergency stop functions accurate counterbending die positioning footswitch 3 hexagonal tool holders heavy-duty steel gear case users manaul tools not included, prices on request

Condition: good (used), Year of construction: 2002, received a new control unit in 2019 for €14,000 max. bending diameter: 63.5 mm smallest bending radius: 32 mm Itedsykl Rzspfx Abnjd motor: 30 kW

Condition: good (used), functionality: fully functional, Year of construction: 2002, control type: manual, degree of automation: manual, actuation type: hydraulic, pipe diameter (max.): 6,090,115 mm, tube wall thickness (max.): 3 mm, number of axes: 3, working height: 700 mm, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, operating pressure: 200 bar, pressure (max.): 200 bar, number of digital displays: 3, Equipment: CE marking, documentation/manual, emergency stop, quick-change device, Limpet coil roller hydraulic to form half round pipe from flat stainless steel strip and bending into wanted radius with spiral continuous. Itodpfxoyik Hcs Abnod -Shafts output 80 mm -Interchangeable set of rollers on the shafts for the different size of pipe 60 mm , 90 mm , 115 mm -Coil holder for the reel metal strip with guide-way bench uncoiling and alignment the steel strip to the rolling machine -Pinching lower central roll adjustable to form the half pipe -Digital position readout to determine the bending diameter of the coil, the pitch of the coil, the half tube shape forming -hydraulic arm movable in 3 directions to set the pitch of the coil roll -Upper vertical support hydraulic operated to hold in position the formed diameter and collect the coils from diameter 700 to diameter 3000 mm -Operator console electric with push buttons and digital position readouts for the coil length, the bending radius and the forming load. -Service manuals and operation books along with the machine