Mistra-Autex

Year of construction: 2026, condition: new, functionality: fully functional, machine/vehicle number: 066 404 601, An extrusion tool for the production of PE or PP pipes is offered. Podpfjzhnd Rex Amuogn Pipe diameter range min: Ø140 mm Pipe diameter range max: Ø250 mm Output approx.: 1000 kg/h Design: Spiral distributor system, completely made of 42CrMo4 Flow contour polished Equipped with cylinder heaters and temperature sensors M14x1.5, type “J” Incl. 3 m connection cable, without plug connector for the extruder Technical data: 230V, 50Hz for max. 3600W per zone, 16A Number of heating zones: 7 2 copies of the operating manual in German or English are included in the scope of delivery. The offer includes the following items: - Base tool PO G 250 - Covering package for a max. 10% outer layer - Flex die insert for Ø250/180 - with this die insert, all dimensions from Ø250 to Ø180 can be produced in SDR17 + SDR11 - Tool mounting carriage, swiveling by 90° - Internal cooling for oil or water in the spiral distributor - Prepared for the installation of a pipe head air cooling system

Year of construction: 2017, condition: ready for operation (used), I. PE/PP Waste Regranulation Line, Model: YDN-120 Material: PP/PE Maximum Capacity: PP: 550 kg/h PE: 650 kg/h Installed Power: 420 kW Power Consumption during Operation: approx. 250 kW Water Consumption: approx. 25 l/min Required Water Pressure: 3 kg/cm² 1) Extruder Designed for double degassing Double-stage gearbox Screw Diameter: 120 mm Made of SACM 645 steel, chrome-plated and hardened L/D Ratio: 32:1 Rotation Speed Range: 0-130 rpm Heater Power Consumption on the Barrel: 51 kW Number of Heating Zones on the Barrel: 5 Barrel Cooling: 1/8 HP x 5 fans Motor: 175 HP, controlled by a frequency inverter 2) Screen Changer, 15 HP Filtering Area: 90,639 mm² x 2 Equipped with a pressure sensor and alarm. If the pressure is too high, the machine will automatically shut down. One temperature control zone. 3) Cutting Knife System for Granulation on the Extruder Head Number of Knives: 4 pcs. Temperature Control: 1 zone Heating Power: 3.5 kW 2 heads for PE 4) Water Cooling System Motor: 5 HP, controlled by a frequency inverter 5) Shredding and Pre-compaction Drum Vertical type with temperature sensor Motor Power: 150 HP, controlled by a frequency inverter Equipped with 12 rotating knives and 17 stationary knives Mill Diameter: 1300 mm Blower: 7 1/2 HP Continuous Water Cooling Device Pgjdpfxjzhm Iho Amuen 6) Conveyor Belt Dimensions: 4950 mm (length) x 670 mm (width) Motor: 2 HP 7) Vibrating Dryer Water Pump: 5 HP x 1 Vibration Motor: 1/4 HP x 4 pcs. Water Tank Dimensions: 3615 mm x 700 mm x 471 mm 8) Regranulate Silo (with centrifugal blower 7.5 HP and transport pipe) 9) Control Panel Indicates the operating status of all major electrical devices The machine is equipped with a double cylinder screen changer, allowing for screen changes without shutting down the machine. The line is designed in a compact manner, saving usable space. The device requires maintaining the cooling water temperature: 25-35°C Equipment: Enlarged drum to 1300 mm with a 150 HP motor Second degassing port on the first screw, with a vacuum pump Metal Detector 5 HP Centrifuge Second "cascade" plasticizing module (150 mm screw) with a filter with a single degassing port and a vacuum pump Double-stage gearbox Parameters of the Second Plasticizing Module Screw Diameter: 150 mm Made of SACM 645 steel, chrome-plated and hardened L/D Ratio: 20:1 Rotation Speed Range: 0-130 rpm Number of Heating Zones on the Barrel: 2 Motor: 75 HP AC motor, controlled by a frequency inverter Control Panel Hydraulic screen changer x 2 cylinders Additional Equipment Increased filtration area on the first screen changer: Standard: diameter 140 mm x W126 mm = 55,389 mm² x 2 After enlargement: diameter 204 mm x W141.5 mm = 90,639 mm² x 2 The delivery includes additional cooling for the control cabinets Static mixer with a connection for homogenization and uniformization of the mass.

Year of construction: 1999, condition: used, The system is not just a simple recycling extruder; it is a complete plastic recycling line consisting of: * Heysohn PAR 108 agglomerator/compactor (1993) * Heysohn extruder with degassing * Material feed and metering * Discharge/conveying system * Documentation available * Multi-zone heating (at least 9 heating zones visible) * Vacuum degassing * 60 kW main drive Pgsdpfx Amezhl R Isujn * RAVIS 2 modular control system * Machine is evidently still fully assembled The control panel shows the following handwritten notes: * Extruder type: presumably PAR 108 * Diameter: 130 mm * Extruder output: approx. 345 kg/h * Motor power: 135 HP The system appears to have been used for processing film and plastic regrind into granules. Battenfeld BFX2-130-25V plastic extruder – year of manufacture 1999 For sale is a plastic extruder from Battenfeld Extrusionstechnik GmbH, type BFX2-130-25V, year of manufacture 1999. The system consists of an extruder, material feed with hopper, drive unit, and conveying system. The machine comes from an industrial plant and is in assembled condition. Manufacturer: Battenfeld Extrusionstechnik GmbH Type: BFX2-130-25V Year of manufacture: 1999 Operating voltage: 400 V / 50 Hz Weight: approx. 9,500 kg

Year of construction: 2026, condition: new, functionality: fully functional, Conical laboratory single-screw extruder EX 60/30 The extruder is designed for processing light, free-flowing granular materials. Due to its screw size, the extruder is suitable for laboratory and testing applications. The nitrided screw with a conical inlet section is fed with materials via a hopper, which then flow through the large inlet opening into the cylinder. Subsequently, the raw materials are compressed in the cylindrical screw section and discharged through a die. A direct drive with an upstream thrust bearing forms the drive train. Ceramic heating bands also allow for high processing temperatures. A shielding cooling system is installed between the material hopper and the first heating zone. Optionally, we also offer the following machines: The strands are passed through a water bath with a stainless steel tank to the strand granulator. A screen changer can also be offered as an option between the extruder and the die. Screw speed 150 Pjdpfx Ajzhamwomujgn Current 29.5A CEE-63A

Year of construction: 2008, condition: used, functionality: fully functional, machine/vehicle number: 2801816/010, We offer this used Cincinnati Talos 75-30G, manufactured in 2008. Pgjdpozg Uuyefx Amujn Manufacturer: Cincinnati Model: Talos 75-30G Year of manufacture: 2008 Condition: used If you have any questions or require further information, please do not hesitate to send us a message or call us.

Year of construction: 2006, condition: ready for operation (used), A complete Battenfeld compact extrusion line for the production of PVC profiles is available. 1) Twin-screw extruder Battenfeld MBEX 2-50-16 V, year of manufacture: 2006, output capacity: 15kg-60kg/h, screw diameter: 52mm, screw length: 16×D, barrel zones: 4, barrel cooling zones: 3, adapter zones: 1, die heating zones: 9, control system: BMCtouch. Including dry vacuum pump, pressure measuring points, clamping flange, water-air separator, blow-off device, mounting elements and hopper cover. 2) Calibration table Battenfeld KP 125 V 2/4m, mounting frame length: 4100mm, mounting rail width: 320mm, longitudinal adjustment: 500mm, transverse adjustment: +/-15mm. 3) Speck vacuum system, pumps: 2, motor power: 2×4kW, operating pressure: 200mbar, max. air capacity: 2×140m³/h. 4) Battenfeld RP 125 SE caterpillar haul-off, passage height: 100mm, contact length: 1100mm, pad width: 160mm, haul-off speed: 15m/min, max. haul-off force: 7kN. 5) Battenfeld SP 63 E underfloor saw, max. cross-section capacity X/Y: 200mm/300mm, sawing accuracy: +/-0.5mm. Overall line dimensions X/Y/Z: approx. 12000mm/1200mm/2000mm, weight: approx. 4500kg, operating hours: approx. 319h. Including chip extraction. The line touchscreen is defective (nothing is visible), however, the line can be operated using an external monitor, mouse and keyboard. Documentation available. An on-site inspection is possible. Pgodpfx Amszg Iqheuen

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1990, machine/vehicle number: E2018, total length: 7,000 mm, total width: 3,500 mm, total height: 6,000 mm, Very well-maintained machine in good working condition. Capacity up to 100 kg/h. Screw diameter 60 mm. Psdozgc Ihspfx Amuegn Head diameter 160 mm. New, additional set of screws and cylinder included.

Condition: used, Grinding Machine Weber MSG 460 2 2 This universal Weber knife grinder has been specifically designed for sharpening circular knives. These knives require precisely sharpened edges, optimal cutting angles, and accurate cutting edge geometry. The machine ensures this with consistent, repeatable accuracy throughout the entire service life of the cutting tools. The short setup time, combined with the non-driven grinding wheels, makes this an efficient machine for small to medium-sized meat processing companies. Specifications: - Knife diameter working range: 420–460 mm - Grinding angle adjustment: 15°–35° Pgsdpfjzf Adtox Amuen - Voltage: 380 V (3 + N, 50 Hz) - Power: 0.18 kW - Weight: 91 kg - Machine dimensions (W × D × H): 570 × 670 × 1510 mm

Condition: reconditioned (used), Overall condition: Very good Pgedjzfzg Tepfx Amuon Recent maintenance: The cylinder (barrel) was replaced last year.

Year of construction: 1995, condition: ready for operation (used), functionality: fully functional, power: 52 kW (70.70 HP), screw conveyor diameter: 49 mm, machine/vehicle number: DE27566, TECHNICAL DETAILS Capacity: 150 – 250 kg/h Screw diameter: 2 x Ø 49.7 mm L/D ratio: 32D Pgsdpfxezd Scpo Amuon MACHINE DETAILS Motor power: 52 kW (DC) Control system: analog, contactor-controlled system EQUIPMENT Synchronous motor Degassing Vacuum pump

Year of construction: 2009, condition: excellent (used), functionality: fully functional, Film up to 1400 cm wide With ParsControl Gravimetric AB line Podpfx Amjzd Ai Houogn

Year of construction: 2010, condition: excellent (used), 414 USED Bakery oven, trolley, rotary, 60x80 cm. Year of manufacture: 2010. EXTERNAL DIMENSIONS (in cm): - W: 155, - L: 175 (with hood 237) - H: 263. The USED device is available to verify in our warehouse (36-068 Bachórz, Poland). Paid options available: renovation / transport / assembly / commissioning of the device. The price is a net price. Pgodpfezdra Iex Amusn Our languages: ENGLISH, FRENCH, GERMAN, UKRAINIAN.

Year of construction: 2001, condition: good (used), For sale: an industrial twin-screw extruder, Werner & Pfleiderer ZSK 133, now known under the Coperion brand. This machine is designed for processing and compounding plastic materials, especially PP granules, polyolefins, masterbatches, filled, and modified materials. Psdpfxozc I Igo Amujgn The extruder was manufactured in 2001 and purchased used in 2015 in working condition. However, it has not been used in our production since the purchase. It has been idle since then and is being sold due to lack of use. Key specifications: capacity up to 4 t/h, main electric motor 1100 kW, voltage 690 V, frequency 50 Hz, motor speed 1492 rpm, screw speed up to 400 rpm, maximum pressure 200 bar, heating power 137 kW, 6 heating zones, dimensions 3535 × 900 × 500 mm. The extruder includes a melt pump, an underwater granulator with a die and a set of knives, a cooling system for a water bath, an oil unit with electric heaters for heating the granulation die, and hydraulic units for operating and locking the shears. Suitable for factories involved in compounding, PP granule production, masterbatch production, regranulation, and processing of large volumes of plastic.

Year of construction: 2001, condition: used, The line is suitable for high-quality mono film production with automatic thickness control, IBC cooling, and full surface treatment capability. Single-layer blown film extrusion line based on a 120 mm extruder with a 30:1 L/D ratio and water-cooled grooved feed section. Die Head • Model: TE594 • Die diameter: 350 mm • Die gap: 1.5 mm Metering System • 4-component gravimetric system (Octagon configuration) Cooling & Control • Plast-Control GmbH Procon automatic air ring & profile control • K-Design GmbH USBC-4-G2 IBC with WR-4 width control Corona Treatment • AFS G100S • Double treater station, 2600 mm width Take-up & Winding • 2800 mm take-up and winding unit • Oscillating take-up with gusset boards • Erhardt+Leimer GmbH web guiding system • 3” and 6” air shafts Podpezcz Ruefx Amuegn Recently replaced (less than 12 months of use, original Macchi parts): • Main motor • Gearbox • Screw & barrel • Mixing tip • Grooved feed section

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 51005604, screw diameter: 60 mm, Equipment: documentation/manual, Krauss Maffei KMD 60 K/P - Year of manufacture 2008 - Conical counter-rotating plasticizing system - Capacity 55-180 kg/h - Screw diameter 60 mm Pgedpfx Amjzclaysusn The extruder is in very good technical condition. It has previously used with PVC dry blend in the production of window profiles. The plasticizing system does not require replacement or regeneration.

Year of construction: 1999, condition: good (used), functionality: fully functional, Complete Bausano 146 twin-screw extruder line for PVC granulation. Podpfx Aezcarqjmuogn

Year of construction: 2010, condition: good (used), functionality: fully functional, The front carriage is in reasonably good condition and contains various male and female connectors. Psdpszb U Rlofx Amuogn

Year of construction: 2014, condition: used, Leistritz ZSE 60 MAXX-36D Extrusion Line (2014) comprising Podpfxozb N Hzo Amusgn Koch Technik and Scholz Dosiertechnik feeding system dosing units Leistritz ZSE 60 MAXX-36D twin-screw extruder with 2x 60mm diameter screws 36:1 L/D ratio, co-rotating 8-barrel housing section, electrically heated and water-cooled 2 degassing ports 1200 rpm maximum screw speed 495kW motor with Flender direct-driven gearbox Free-standing control panel with microprocessor and interconnecting wiring BD Plast BDL double screen changer Ettlinger ERF 200 melt pump Econ EUP 600 pelletizer Stainless steel water bath incl 2x sifters on legs Tredkamp 1C-T 10,000L stainless steel mixing silo Motan 14,000L mixing silo on legs with elevator Big bag system

Condition: used, We offer directly on behalf of the owner : Twin-screw extruder Make : COPERION ( Werner & Pfleiderer ) Gearbox make : P.I.V Type : ZSK 170 W 1920/1750 Year of construction : 2021 / 2002 / 1986 Screw diameter : 172 mm Screw speed : 4,9 - 49 min-1 Max. torque : 17,500 Nm Main engine : 216 kW In the last 3 years, a total of over €420,000 has been invested in new components and factory overhauls (some of which were previously unused) The extruder was in use until Aug / 2023 and has already been dismantled ready for transport. The components are partly redundant and date from the years 1986 - 2021. The scope of delivery consists of : Twin screw degassing Coperion DSE 180 - 1 x year of manufacture 2021 ( 180 t€ ) Main gearbox P.I.V Pgedpfx Aozbvqtomuon - 1 x year of manufacture 2002, factory overhauled ( 233 t€ ) in 2021, unused - 1 x year of manufacture 1986, factory overhauled in 2016, used 2021 - 2023 Main engines Siemens, 212kW, 460V - 1 x 2002, factory overhauled ( 8 t€ ) in 2020, unused - 1 x year of manufacture 1986, factory overhauled in 2015, used 2020 - 2023 Barrels - 16 various, new + used, with + without openings Screw shafts - 2 x approx. 4,600 mm Miscellaneous : - Supports - screw tips Sold without electrical and control devices and without screw segments. Further technical data and details on request or see data sheets in photos / PDF

Year of construction: 2002, operating hours: 1,378 h, condition: excellent (used), Brand: Berstorff Type: ZE 25 compounding line Serial no.: 90200771-0010/2002 Year of manufacturing: 2002 Operating hours: 1,378 Screw diameter: 25 mm Screw L/D: 44 Dimensions (LxWxH): 4,500 x 1,200 x 2,200 mm Weight: 1,350 kg Line configuration: – 1x gravimetric powder feeding system from Brabender – 1x vent port for degassing, including vacuum pump – Filament die with 6 cavities – Cooling roll with tempering unit – Pelletizer with adjustable speed – Central control cabinet Other: All documentation available in German The machine was originally used for biomaterials Pgjdpfx Amozbrfgeuon

Year of construction: 2016, condition: excellent (used), 2016 MODEL * Capable of easily processing even tough industrial plastic waste while preserving the material's properties * Output capacity of up to 1,000 kg per hour, depending on the type * Start and stop operation with a single button * Quick and easy start and stop functionality * Saves space due to its small footprint Not only does it process all types of plastic waste, but it also easily handles bulky materials such as large bales and carpet padding without pre-sizing. It is also at the highest level in terms of efficiency. Thanks to the shredding unit that preserves the material and the optimized extrusion process, you can sustainably achieve your zero-waste goals with X (all production waste is recycled). Plastic waste is processed by a heavy-duty shredding unit that operates at a low speed to minimize loss of material properties. In this process, a hydraulic piston pushes the material to be shredded towards the shredding shaft. The shredder and extruder drives are controlled separately and automatically, depending on the load. After the shredding process, the shredded material is transferred directly to the extruder via a feed screw. In the extruder, the material is brought to a homogeneous melting temperature and, if necessary, degassed. All components are positioned close to each other to prevent oxidation of the material and to make the best use of the heat generated during the shredding process. In a single process step, the slow-rotating shredding blades grind the plastic waste, and the shredded material is continuously transferred to the extruder via the feed screw. Large, thick, or bulky waste can be processed directly, as long as it fits into the hopper, without requiring a shredding process. The control system ensures the smooth start-up of the equipment components. After an unexpected stop, it can be restarted in less than two minutes with a full hopper and a full extruder. The material level in the hopper is continuously measured, and the feed is adjusted accordingly. Uneven filling of the conveyor is possible – the NGR control unit takes care of the rest. Podpfx Ajzblm Rsmusgn

Year of construction: 2016, condition: excellent (used), 2016 MODEL * Capable of easily processing even tough industrial plastic waste while preserving the material's properties * Output capacity of up to 1,000 kg per hour, depending on the type * Start and stop operation with a single button * Quick and easy start and stop functionality * Saves space due to its small footprint Pgsdjzblirepfx Amuon Not only does it process all types of plastic waste, but it also easily handles bulky materials such as large bales and carpet padding without pre-sizing. It is also at the highest level in terms of efficiency. Thanks to the shredding unit that preserves the material and the optimized extrusion process, you can sustainably achieve your zero-waste goals with X (all production waste is recycled). Plastic waste is processed by a heavy-duty shredding unit that operates at a low speed to minimize loss of material properties. In this process, a hydraulic piston pushes the material to be shredded towards the shredding shaft. The shredder and extruder drives are controlled separately and automatically, depending on the load. After the shredding process, the shredded material is transferred directly to the extruder via a feed screw. In the extruder, the material is brought to a homogeneous melting temperature and, if necessary, degassed. All components are positioned close to each other to prevent oxidation of the material and to make the best use of the heat generated during the shredding process. In a single process step, the slow-rotating shredding blades grind the plastic waste, and the shredded material is continuously transferred to the extruder via the feed screw. Large, thick, or bulky waste can be processed directly, as long as it fits into the hopper, without requiring a shredding process. The control system ensures the smooth start-up of the equipment components. After an unexpected stop, it can be restarted in less than two minutes with a full hopper and a full extruder. The material level in the hopper is continuously measured, and the feed is adjusted accordingly. Uneven filling of the conveyor is possible – the NGR control unit takes care of the rest.

Year of construction: 2006, condition: used, functionality: fully functional, Complete Extrusion Line for Plastic Pipes Luigi Bandera / Graewe / Supertech Year of manufacture: 2006 For sale: Complete extrusion line for the production of plastic pipes. Installed in a mobile container setup = 3 x 40-foot sea container. (Walking Pipe system). Ideal for mobile production or limited space. Specifications: Extruder: Luigi Bandera S.p.A. Year of manufacture: 2006 Serial number: 251371 / 251372 Downstream processing / cooling line: Supertech Industrie – Walking Pipe system Saw / cut-off unit: Graewe GmbH Type: RA 250/4 Year of manufacture: 1999 Pgjdpfxjzbkkhj Amuen Control system: Krauss Maffei Installation: fully integrated in container (plug & play concept) Description: This robust extrusion line is suitable for the production of plastic pipes (PE/PP/PVC depending on configuration). The line consists of a powerful Bandera extruder, followed by a complete calibration, cooling and transport section (Walking Pipe), and a Graewe cut-off saw. Applications: Drainage pipes Cable protection pipes Industrial pipelines Irrigation systems 💬 Price on request 📍 Viewing possible by appointment; address = 7822 Ath, Belgium Keywords: Technical / industrial Extrusion machine Extrusion system Extrusion line Screw extruder Melt processing machine Plastic processing machine Pipe production machine Profile extrusion machine Continuous forming machine Melt and forming system

Year of construction: 1996, operating hours: 25,000 h, condition: good (used), functionality: fully functional, single-screw extruder, 90 Reifenhauser, complete with electrical panel and 200 kW motor. The machine is in excellent condition. Podpfx Amezbh Ahsuogn

Year of construction: 1995, condition: ready for operation (used), functionality: fully functional, total length: 2,100 mm, total width: 730 mm, heating capacity: 7.5 kW (10.20 HP), screw conveyor diameter: 35 mm, machine/vehicle number: DE27307, TECHNICAL DETAILS Capacity: 30 – 80 kg/h Screw diameter: 2 x 35.0 mm L/D ratio: 20:1 Screw speed: 80 rpm Gearbox ratio: 12:1 Pgedpfxezargne Amusn Number of heating zones: 5 Heating power: 7,500 W Number of cooling fans: 5 Extruder discharge height: 1,150 mm MACHINE DETAILS Control system: Analog, contactor-controlled system Drive / Motor: 20 kW (DC) Cooling fan connection: 230 V Gearbox type: Lenze Material: PE, PP, PS, ABS Design: Co-rotating, degassing, vacuum pump Dimensions (L x W): 2,100 x 730 mm Note: Water bath and granulator can be purchased for an additional charge.