CarComm International BV

Condition: used, Year of construction: 2004, Victory 330/80 PLUS Year: 2004 Serial No.: 52863 Operating hours: 103,000 Screw: D40 CC200 A01 4-circuit water cooling Fgedjzcaxdopfx Adtoc 1x core pull 4x digital input, 4x digital output Few sockets ROBOT: TecnoMatic Micro 210/0184 Year: 2021 Load: 3 kg X-Y-Z – servo C – pneumatic

Condition: used, Year of construction: 2013, Model: BOY 55 E Machine type: Injection molding machine Year of manufacture: 2013 72,000 operating hours Serial number: 55241 Clamping Unit • Clamping force: 550 kN (55 tons) • Tie bar spacing: 360 x 335 mm • Opening stroke: approx. 400 mm • Minimum mold installation height: 250 mm Fodpfozcav Njx Adtjgc • Maximum plate distance: 650 mm Servo drive system (E-version): • Up to 30–50% lower energy consumption compared to conventional hydraulics Hydraulic motor power: approx. 7.5 – 11 kW Including: ROBOT: tecno matic micro 13-0040 Payload capacity: ~1–3 kg

Condition: used, Year of construction: 2006, operating hours: 4,500 h, VICTORY 200/80 Power SN: 50294 Year: 2006 Closing force (kN): 800 S10 screw, diameter 30mm Operating hours: ONLY 4,500 Mounting plates enlarged vertically Mould heater with 12 control loops HV 2 version with control pumps (pressure and flow control in a closed control loop) for parallel movement sequence Microcomputer CC100 A03 Ethernet interface for use with EMS 8x digital output, 8x digital input Interface for ejector protection Interface for temperature control units, Data protocol: Engel, physical type: 20MA-CL Microflow MINI-CAM: Process parameter adjustment support based on an expert system 2-pole service socket, 230V 6x 3-phase socket, 10A / 16A 2x 3-phase socket, 10A / 16A, switchable 2/2-way magnetic air valve, R1/4 inch Flow regulator 0-10 l, 4 circuits Temperature control circuits can be switched off manually or automatically (centrally at the flow controller) - Switch-off function selectable. Fgjdpfx Adezcanretjc Tubing for flow controller, 4 temperature control circuits

Condition: used, Year of construction: 2003, operating hours: 6,500 h, VICTORY 200/60 Power SN 162699 Closing force (kN) 600 (expandable to 800 kN) Year of manufacture: 2003 Screw diameter 30.00 mm, L/D ratio of the mixing cylinder 20.50 Operating hours: ONLY 6,500 Vertically enlarged clamping plates (B-plates) Fsdpezcanfefx Adtogc Swiveling reject chute for reject selection, activated upon reject detection Version variant HV 2 with control pumps (pressure and flow control in a closed-loop control system) for parallel movement sequence Microcomputer CC100 A03 Kistler 5155 A2213Q02 charge amplifier with automatic switching pressure detection 4x digital output, 4x digital input Interface for temperature control units or hot runner controllers Data protocol Engel, physical type 20 mA – CL Microflow MINI-CAM - Process parameter adjustment support based on an expert system 1x service socket, 2-pole, 230V 4x 3-phase socket, 10A / 16A 2x 3-phase socket, 10A / 16A, switchable 2/2-way solenoid air valve, R1/4 inch Flow regulator 0-10 l, 8 circuits Temperature control circuits can be switched off manually or automatically (centrally at the flow controller) – Switch-off function selectable.

Condition: good (used), Year of construction: 2014, Clamping force: 50 t Screw diameter: 30 mm Distance between tie bars V: 320 mm Distance between tie bars H: 320 mm Shot volume: 85 cm3 Shot weight: 77 g Injection pressure: 2000 bar Fedpfxezcaipj Adtogc Type: Horizontal Drive: Hydraulic

Condition: good (used), Manufacturer: Arburg Year of manufacture: 1999 Machine number: 175831 Type / Model: 370S-800-350 Fodpfjzbx Aljx Adtogc Operating hours: Automatic cycle hours: Clamping force: 80 t Opening stroke: 500 mm Tool mounting height: 250 mm Column spacing: 370 x 370 mm Platen dimensions: 570 x 570 mm Screw diameter: 35 mm (?) Maximum dosing volume: 139 cm³ Shot weight: 117 g Holding force: 5 t Connection: 28 kW Accessories/Equipment: 1 core pull, removal gripper Condition: good Weight: 3.5 t Dimensions: 4,300 x 1,500 x 2,100 mm

Condition: excellent (used), Year of construction: 2016, ARBURG A 470 H 1000-170 HIDRIVE (32.000 h) (S&P 3796) Manufacture year: 2016 Operating hours: 32,000 Stunden Screw: 30 mm Injection pressure: 2000 bar Stroke volume: 85 cm³ Clamping Force: 100 t Tie bar distance: 470 x 470 mm Mould installation height min.: 250 mm Plate distance max.: 850 mm Dimensions: 4100 x 1700 x 2400 mm Eeight: 5030 kg Fgsdpfx Adszbay Sstoc Connected load: 21 kW Accu, Robot Interface EM67, EM73, Airvalve Price: on request contact: Mr. Ralf Schulz

Condition: excellent (used), Year of construction: 2012, ARBURG A 375 V 500-170 Turntable (S&P 3773) Fjdpozbay Eofx Adtegc Manufacture year: 2012 Operating hours: 36,900 Stunden Screw: 25 HVF mm Injection pressure: 2500 bar Stroke volume: 59 cm³ Clamping Force: 50 t Mould installation height min.: 170 mm Plate distance max.: 520 mm Dimensions: 3300 x 1700 x 2100 mm Eeight: 3740 kg Connected load: 11 + 11 = 22 kW Vertical injectionmoldingmachine with a 900mm turntable, 2 station 180°, incl. Option for horizontal injection into parting line incl. lifting table, Robot Interface EM67, Airvalve, EM73, Hotrunner etc...price when new approx. 170.000,- Euro Price: on request contact: Mr. Ralf Schulz

Condition: good (used), Year of construction: 2007, Ref. no.: 18615 Manufacturer: DEMAG Type: IntElect 80/370-100 NC4 All Electric Year of construction: 2007 Clamping unit Clamping force: 80 ton Opening stroke: 340 mm Distance between tie bars: 370 x 370 mm Mould height min.: 150 mm Injection unit Screw diameter: 25 mm Injection volume: 51 cm³ Shot weight: 45 g Injection pressure: 2000 bar Measurements and weight Dimensions: 4,3 x 1,3 x 2,3 m Machine weight: 4750 kg Further information: A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs. Motor System — Siemens MOTICS 3 Main Drive Motor · Water-Cooled Servo Motor The main drive unit that controls all clamping and injection movements with high precision. Plasticising Motor · Water-Cooled Servo Motor Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production. 5-Axis Full Servo Control The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems. Fgodpfx Adoza Dc Uotec NC4 Control System The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.

Condition: good (used), Year of construction: 2008, clamping force: 900 kN, Equipment: documentation/manual, Technical data: Clamping force: 90 t Screw diameter: 28 mm Shot weight: 74 g Injection pressure: 180 bar Column spacing: 1.5 m: 430x360 mm Plate size: 360 mm: 635x610 mm Minimum mold height: 250 mm Language: German, English, Czech, Slovenian Installed power: Power: 22.3 kW Fjdpszavbiefx Adtogc Weight: 3100 kg Dimensions: 3.9x1.3x1.9 m

Condition: excellent (used), Year of construction: 2004, 1,0 St. gebr. Spritzgießmaschine Hersteller: DR. BOY Typ: 22 D Baujahr: 2004 Schließkraft: 22 Tonnen Holmabstand: 254 x 254 mm Einbauhöhe MIN, / MAX. 200 / 400 mm Schnecken DN: 22 mm Spritzteilgewicht 27 g/PS Fsdjzardgopfx Adtjgc

Condition: excellent (used), Year of construction: 1999, 1,0 St. gebr. Spritzgießmaschine Hersteller: DR. BOY Typ: 22 D Baujahr: 1999 Fedpfszaqzdjx Adtsgc Schließkraft: 22 Tonnen Holmabstand: 254 x 254 mm Einbauhöhe MIN, / MAX. 200 / 400 mm Schnecken DN: 22 mm Spritzteilgewicht 27 g/PS

Condition: used, Year of construction: 2002, operating hours: 49,100 h, functionality: fully functional, clamping force: 450 kN, overall weight: 3,300 kg, First owner Fodpfxezal Ths Adtegc

Condition: good (used), Year of construction: 2007, Ref. no.: 18616 Manufacturer: DEMAG Type: IntElect 80/370-100 NC4 All Electric Year of construction: 2007 Clamping unit Clamping force: 80 ton Opening stroke: 340 mm Distance between tie bars: 370 x 370 mm Mould height min.: 150 mm Injection unit Screw diameter: 25 mm Injection volume: 51 cm³ Shot weight: 45 g Injection pressure: 2000 bar Fjdozabkvopfx Adtjgc Measurements and weight Dimensions: 4,3 x 1,3 x 2,3 m Machine weight: 4750 kg Further information: A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs. Motor System — Siemens MOTICS 3 Main Drive Motor · Water-Cooled Servo Motor The main drive unit that controls all clamping and injection movements with high precision. Plasticising Motor · Water-Cooled Servo Motor Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production. 5-Axis Full Servo Control The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems. NC4 Control System The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.

Condition: excellent (used), Year of construction: 2020, WOOJIN PLAIMM TE 50 INJECTION MOLDING MACHINE Technical specifications: Machine type: electric injection molding machine Year of manufacture: 2020 Operating hours: Fedpfx Ajy Ulfzedtogc Auto: 44,097 h Motor: 3,719 h Additional counter: 28,454 Clamping force: 490 kN Injection volume: 34 cm³ Screw diameter: 22 mm Injection weight: approx. 30–35 g PS Maximum mold opening stroke: 250 mm Column spacing: 360 x 360 mm Platen dimensions: 530 x 580 mm Minimum mold height: 130 mm Centering hole diameter: 125 mm Maximum injection pressure: 2184 bar Total power: 20.7 kW Machine weight: 3600 kg Machine type: electric (E) The machine is in very good technical and visual condition. It has been regularly used in serial production and is available for inspection while in operation.

Condition: excellent (used), Year of construction: 2011, BATTENFELD 35/75 PLUS INJECTION MOLDING MACHINE Technical specifications: Year of manufacture: 2011 Operating hours: 89,192 h Clamping force: 350 kN Injection volume: 25.4 cm³ Injection shot weight: approx. 23–27 g PS Screw diameter: 18 mm Maximum mold opening stroke: 200 mm Column spacing: 270 x 260 mm Platen dimensions: 470 x 280 mm Minimum mold height: 150 mm Centering hole diameter: 110 mm Fgodpfx Aey Uk Axodtec Maximum injection pressure: 2034 bar Hydraulic oil volume: 125 dm³ Total power: 28 kW Machine weight: 1050 kg Machine type: hydraulic Control system: BATTENFELD UNILOG B2 The machine is in very good technical and visual condition. A larger number of machines in the same configuration are available – a total of 12 units manufactured in 2010–2011.

Condition: excellent (used), Year of construction: 2016, clamping force: 800 kN, Clamping force: 80 t Screw diameter: 30 mm Fjdpfx Adoy Uffuotegc Distance between tie bars V: 180 mm Distance between tie bars H: 180 mm Type: Vertical Drive: Hydraulic

Condition: excellent (used), Year of construction: 2006, clamping force: 500 kN, screw diameter: 22 mm, clearance between the columns: 355 mm, displacement volume: 41 cm³, injection pressure: 2,800 bar, injection weight: 37 g, mold height (min.): 210 mm, overall weight: 2,700 kg, Clamping force: 50 t Year of manufacture: 2006 Injection unit .../200 Screw diameter: 22 mm Specific injection pressure: 2800 bar Injection volume: 41.8 ccm Mould clamping system 50/... Clamping force: 50 t Mould plate dimensions: 520 x 520 mm Tie bar clearance: 355 x 355 mm Mould height: 210 mm Opening stroke: 400 mm Maximum platen distance: 610 mm Weight: 2700 kg Fgjdpfjy Tvvnsx Adtoc Dimensions (m) L x W x H: 3.8 x 1.1 x 2.1 m Control: NC4

Condition: excellent (used), Year of construction: 2004, Arburg 420C 800-250 Year of manufacture: 2004 Injection unit: Screw diameter: 30 mm Shot weight: 89 g Injection pressure: 2470 bar Dosage volume: 106 ccm Clamping unit: Clamping force: 80 t Tie bar spacing: 420x420 mm Platen size: 570x570 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA Additional equipment: Fgjdpsy Smu Eofx Adtsc Euromap 67 Robot interface Hydraulic core pull x 1 Injection unit hardened – bimetallic Dimensions: Weight: 3180 kg Length/Width/Height: 4.30x1.64x2.08 m Drive: Pump/motor: 15 kW Heating capacity: 6.5 kW Total power: 21.5 kW All machines offered are started up by our service engineers before sale. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical demonstrations at our facility in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2003, Arburg 420S 800-350 Year of manufacture: 2003 Injection unit: Screw diameter: 50 mm Shot weight: 250 g Injection pressure: approx. 1300 bar Dosage volume: 288 ccm Clamping unit: Clamping force: 80 t Tie bar distance: 420x420 mm Platen size: 570x570 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA Additional equipment: Euromap 12 interface Robot interface Air valve x 1 Core pull control Injection unit hardened - bimetallic Proportional valve on the injection unit – for precise injection Integrated original Arburg side sprue picker Dimensions: Weight: 3,800 kg Fgedpfx Ajy Smurodtsc Length/Width/Height: 4.06x1.39x2.12 m Drive: Pump/Motor: 18.5 kW Heating capacity: 10.2 kW Total power: 28.7 kW All offered machines are started up by our service technicians before sale. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 1999, Arburg 420C 800-250 with the sprue picker anvil+long leg Year of construction: 1999 Injection unit: Screw diameter: 40 mm Injection weight: 158 g Injection pressure: 1390 bar Metering volume: 188 ccm Clamping unit : Clamping force: 80 t Distance between tie bars: 420x420 mm Size of the clamping platens: 570x570 mm Ejector: hydraulic Clamping unit: hydraulic Control system: SELOGICA Fgjdsy Smulepfx Adtjc Additional equipment: Euromap 12 Robot interface Control system with air valve Core pull control Hardened injection unit - bimetal Dimensions Weight: 3180 kg Length/width/height: 4.30x1.64x2.08 m Drive: Pumps/motor: 15 kW Heating output: 6.5 kW Total output: 21.5 kW All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2005, Arburg 1200T 800-150 / Vertical Injection Molding Machine with Rotary Table Year of Manufacture: 2005 Fgjdpfx Adsy Smufstjc Injection Unit: Screw Diameter: 25 mm Injection Weight: 45 g Injection Pressure: 2500 bar Dosing Volume: 54 cc Clamping Unit: Clamping Force: 80 t Tiebar Distance: 0 x 0 mm Clamping Platen Size: 1200 mm Ejector: Hydraulic Clamping Unit: Hydraulic Control System: SELOGICA Additional Equipment: Air Valves x 6 Hydraulic Core Pullers x 6 Control System with Hot Runners Injection Unit Hardened - Bimetal Rotary Table Diameter: 1200 mm Kistler Sensor - Mold Pressure Control Machine serviced by the authorized Arburg Service Center in Germany Dimensions: Weight: 7400 kg Length/Width/Height: 3.92 x 1.61 x 3.78 m Drive: Pump/Motor: 22 kW Heating power: 9.4 kW Total power: 31.4 kW All offered machines are started by our service technicians before sale. You can receive a video of the technical tests of the selected machine or participate in live technical tests at our facility in Łódź. Price: Upon request

Condition: excellent (used), Year of construction: 1999, Arburg 420C 800-250 Year of construction: 1999 Injection unit: Screw diameter: 35mm Injection weight: 121 g Injection pressure: 1820 bar Metering volume: 144 ccm Clamping unit: Clamping force: 80 t Distance between tie bars: 420x420 mm Size of the clamping plates: 570x570 mm Ejector: hydraulic Clamping unit: hydraulic Control system: SELOGICA Additional equipment: Very good technical condition Fgodpfx Aey Smt Isdtoc Machine has produced molded parts for medical industry - clean production conditions Euromap 12 Robot interface Core pull control Hardened injection unit - bimetal Dimensions Weight: 3180 kg Length/width/height: 4.30x1.64x2.08 m Drive: Pumps/motor: 15 kW Heating output: 6.5 kW Total output: 21.5 kW All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2004, Arburg 420C 800-250 with the Wittmann W721 robot Year of construction: 2004 Injection unit: Screw diameter: 30 mm Injection weight: 89 g Injection pressure: 2470 bar Dosing volume: 106 ccm Clamping unit: Clamping force: 80 t Distance between tie bars: 420x420 mm Size of the clamping platens: 570x570 mm Ejector: hydraulic Clamping unit: hydraulic Control system: SELOGICA Fgedpoy Smtzjfx Adtec Additional equipment: Euromap 67 Robot interface Air valve x 2 Hydraulic core pull x 2 Control unit with hot runners Hardened injection unit - bimetal Proportional valve on the injection unit - precise injection Built-in pressure quality control system from Sensor Kistler - mold pressure measurement Original mold crane Robot Wittmann W721 Year of manufacture: 2007 4-axis robot: 3 axes are driven by servomotors (electric); axis C Travel in axes: X-550, Y-1200, Z-1250 Touch control panel Robot with adapter Purchase of the robot for an additional charge Dimensions Weight: 3180 kg Length/width/height: 4.30x1.64x2.08 m Drive: Pumps/motor: 15 kW Heating output: 6.5 kW Total output: 21.5 kW All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2009, Arburg 370S 700-100/100 / 2K machine / operating hours: 33.544 in automatic mode / very good technical condition Year of manufacture: 2009 injection unit: Screw diameter: 30 mm injection weight: 65 g Injection pressure: 1390 bar Metering volume: 71 ccm Clamping unit: clamping force: 70 t tie bar distance: 370x370 mm size of clamping platens: 510x510 mm ejector: hydraulic clamping unit: hydraulic Control system: SELOGICA - touch screen Additional equipment: 2K machine Operating hours: 33.544 in automatic mode Euromap 67 Robot interface Air valve x 5 Hydraulic core pull x 2 Control with hot runners Reinforced injection units - bimetal Proportional valves on injection units - precise spraying Parallel movements The vertical injection unit - screw diameter fi 20 mm (29 g/hp) Machine with cylinder / battery with compressed nitrogen (additional charge for fast work) Machine with the built-in conveyor belt Arburg and original sorting flap There is a possibility to buy an original Weber turntable It is possible to change screw diameters in both injection units for the screw diameters recommended by the manufacturer Dimensions: Weight: 4440 kg Length/width/height: 3.48x1.58x2.97 m Drive: Pumps/motor: 15 kW Heating power: 4,9 kW Fedpfx Aey Smtuodtogc Total power: 19,9 kW All offered machines are started by our service technicians before sale. It is possible to get a video of technical tests of the selected machine or participate in live technical tests in our company in Łódź. Price: Upon request