Used Gesan Dp 75 for sale (25,510)

Condition: used, Year of construction: 1983, Double mitre saw Year of construction 1983 for dimensionally accurate cutting of small cross sections of wood, plastic and aluminum e.g. for galley rails, picture frames, edgings etc. both saw units are infinitely adjustable for 90° to 45° cuts the length is set by hand according to the scale or, in the case of pre-cut lengths by scanning with a special pair of slotted fences, which are removed from the cutting area during sawing (optional) Cutting length max. 2200 mm min. 240 m Pneumatic saw feed with oil brake cylinder, infinitely variable Clamping device from the front and/or from above, pneumatically operated, from above up to max. 50 mm workpiece height Pneumatic control Safety two-hand control, individual switching for each saw unit Compressed air connection 6-7 bar Air consumption/working clearance 3-4.5 NL Connection for suction 50 mm Cebot Haf Dovhu Izorb Saw blade drive 2 x 1.1 kW three-phase motors 2800 rpm Dimensions 2940 x 1100 x 1220 mm Weight approx. 360 kg Availability: short term Storage location: Flörsheim

Condition: new, Year of construction: 2025, Optimum Metal Band Saw OPTIsaw S 275NV Metal band saws with pivoting saw frame. S 275NV with continuously adjustable saw blade speed Item number: 3300265 TECHNICAL DATA Dimensions and weights Length (product) approx. 1400 mm Width/Depth (product) approx. 685 mm Weight (net) approx. 185 kg Max. width/depth (product) approx. 985 mm Max. height (product) approx. 1700 mm Electrical data Drive motor power: 1.5 kW Connection voltage: 230 V Mains frequency: 50 Hz Coolant pump motor power: 90 W Machine data Saw blade speed(s): 20 – 90 m/min Saw blade length: 2480 mm Saw blade width: 27 mm Saw blade thickness: 0.9 mm Cutting angle: 0 – 60° Feed: continuously variable Adjustable Cjbvjgx T I Ushu Izorb Manual saw frame lifting Cutting ranges Cutting range 0° round (solid material) 225 mm Cutting range 0° square (solid material) 190 mm Cutting range 0° rectangular horizontal (solid material) 150 x 245 mm Cutting range +45° round (solid material) 145 mm Cutting range +45° square (solid material) 150 mm Cutting range +45° rectangular horizontal (solid material) 190 x 150 mm Cutting range +60° round (solid material) 90 mm Cutting range +60° square (solid material) 90 mm Cutting range +60° rectangular horizontal (solid material) 120 x 90 mm Explanation of cutting range: Cutting range determined based on the weight of the saw frame with aluminum. May vary depending on the material used and may be smaller (not cutting capacity). SCOPE OF DELIVERY Material stop Bi-metal saw blade Machine base Coolant pump Location: From stock 54634 Bitburg - available immediately -

Condition: new, Year of construction: 2025, Functionality: fully functional, The (fish mask shape) mask machine offered here combines efficiency and safety features with an optimized fit. These product features are, among other things, thanks to the use of ultrasonic technology, an intuitive HMI with touch screen for easy and clear operation as well as an optimized and robust unrolling unit made of steel. Process steps at a glance: Feeding of the filter fleece via a web edge control system, as well as the nose wire, uniform welding of the mask with subsequent folding and separation of the base body. The next process step deals with the attachment of the earband using ultrasonic technology. Optionally, a camera inspection, stacking unit, and a tubular bag machine can be ordered separately. In detail: - Welded unwinding unit with a total of 4 manual tensioning shafts, magnetic powder brakes and web guide control system for feeding the filter fleece. - Nose wire is fed in by means of another unwinder. - The use of panes in combination with slim aluminum profiles allows a good insight into the production while at the same time providing full protection for the operator. - We are happy to offer you various printer systems on request to print the legally required information on your mask. - The use of ultrasonic technology and the use of durable materials such as titanium guarantee increased machine availability compared to conventional materials. - High precision through the use of servo-driven motors. - Uniform material feed and material guidance, as well as separation by means of a rotary cutter with lateral marking output. - High-resolution, user-friendly MHI's with touchscreen. Cobvhu Ijh Uuhcjzerb - Mask body welding using ultrasonic technology with subsequent folding matrix and welding of the upper and lower surface. - Precise separation of the mask from the marking with the help of a rotary blade, with subsequent ejection of the mask and lateral ejection of the marking. - Subsequent ear band embossing by ultrasonic technology. - Optional: Camera inspection with good and bad detection - Optional: Subsequent output to a stacker. - Optional: Output to a flowpack station for individual mask sealing. Performance data & dimensions: - Power consumption: approx. 4-5 KW during operation - Power connection: 220 V/ 50 Hz - Quantities: 80 masks/min. - Compressed air: 7-10 bar - Weight: approx. 2.5 t - Dimensions: 8200x5000x1800 mm (LxWxH) - Mask dimensions closed (longest and widest point): 205 x 82 mm (+- 2mm) We would be happy to send you an individual, high-quality offer. For this we ask you to give us your company data in advance.

Condition: used, mileage: 390,000 km, Year of construction: 2022, Field of application: Freight transport Serial number: YV2R0P0DXNA89xxxx Please contact ATS Norway AS for more information Please provide reference number upon request: 19951 Specifications: - Km: Approx. 390,000 - Transmission: Automatic - 6x4 Tandem lift - Retarder - Air suspension - Euro 6, 751 hp - NATO contact - On-Spot - XXl Cabin - Grill - Extra lights - Tool cabinet - Michelin guys - Compressor horn - Rotor lamps - Led work light - Bed - Refrigerator - Microwave oven - Coffee maker - 1 owner - Nomek construction - Have been on gold deal at Volvo - Ready for delivery Crebvjv U Tp Aehu Izeb Description: 2022 Volvo FH750 Truck with XXL Cabin. 6x4 Tandem lift and Nato connector. The truck has been on a gold contract with Volvo since new. Possibility to buy two identical trucks in total here. Ready for delivery. Km: 390000 HK: 750 Technical approved: Yes EU-approved until: 25.04.2026 Own weight: 11200 Total Weight: 32000 Payload: 20800 Width: 253,6 Length: 748 Euro: 6 Gearbox: Automatic

Condition: excellent (used), Year of construction: 2006, Functionality: fully functional, load capacity: 175 kg, arm reach: 2,550 mm, IRB6600 Serie's upper arm extenders and different wrist modules will allow customization to each process. As the robot can bend fully backwards, the working range is greatly extended and the robot fits well into dense production lines. The IRB 6600 is ideal for process applications, regardless of industry. Typical areas can be Spot Welding, Material Handling and machine tending. Year: 2006 (Same Year, Orange Colour Available) Cabinet: NOT Included (Works with IRC5 - we can try to find one for you) Teach Pendant: NOT included but we can try to find one for you Signalling & Power Cables: NOT Included but we can try to find them for you Please get in touch with us for a quote and also the refurbishment options. As PLC Merkezi EOOD, we have more than 300 robots in our inventory and deal with the brands of KUKA, ABB, FANUC and Motoman. Please note that the price does not include shipping costs. (Source: ABB's Website) Crjbvhjhak Raeu Izjb

Condition: used, 1200702797001 + 1200702758033 / 1200702797001 + 1200702758033 / 1200702797001 + 1200702758033, 003-2391 + 003-2859 / 003 2391 + 003 2859 / 0032391 + 0032859, Thermo Electron Corporation Haake Circulation Thermostat Model: 1200702797001 + 1200702758033 Type: 003-2391 + 003-2859 Condition: Used Cobeq S Udfsvhu Izjrb

Condition: used, Year of construction: 2019, Used machine Year of manufacture 2019 Basic machine - DYNESTIC 7532-10.5 Automatic Dynestic table For classic nesting processing with wear plate Processing length 3100 mm Machine frame in welded construction with ground and hardened prism guides for the traveling column, aggregate head and consoles Traveling column in gantry design Rack and pinion drive, helical gears, in X and Y directions, Ball screw spindles in Z direction for precise positioning Technical data: Processing dimensions: Max. support surface on nesting table: X = 3100 mm Y = 1560 mm Max. travel distances X = 4695 mm Y = 2100mm Z = 293 mm Max. drive-over height DYNESTIC table Z = 100 mm from top edge of table (without wear plate) Maximum programmable speed Vector speed: 128.0 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min DYNESTIC table Fixed, continuous machining table with grid division, continuous grooves in X and Y direction, spacing of the grooves 50 mm with 25 meters of sealing cord for clamping the wear plate Vacuum field 1-circuit vacuum system Drilling unit 7877, 19 spindles Drive power 1.7 kW 13 vertical spindles can be called up individually Arrangement in U-shape 5+4 in X and 4 in Y direction 32 mm grid Max. drill diameter: 35 mm Total drill length: 70 mm from screw end (depending on plate thickness) Spindle extension stroke: 70 mm Direction of rotation: clockwise / anti-clockwise in Change n(max.) 1000 - 4400 min-1 continuously adjustable Mounting: M 10 thread - 11 mm fit without tools, without mounting 6 horizontal spindles 2 double drilling spindles in X direction 1 double drilling spindle in Y direction Mounting: M 10 thread, 11 mm fit Total drill length max. 63 mm from screw end without tools, without mounting Milling unit 7842, Power: 12.0 kW (S6) n(max.) = 1000 - 24000 min-1 continuously adjustable, max. power at 12000 min-1 to 24000 min-1 air-cooled with HSK-F 63 tool holder with right-hand threaded nut (for right-hand rotating tools) with collet chuck with HSK shaft Ceramic ball bearing (hybrid bearing) Tool weight max. 6 kg (incl. holder) Tools: milling and grinding tools max. Ø 160 mm Safety paneling in accordance with CE standard Safety fence on the side and rear Vacuum pump 500 m³/h dry runner Personal safety through light barriers in the front area of the machine Handheld control unit for remote control of the machine with the following operating functions: > Start / stop of the machining program > Speed control of the machining cycles > Reset button > Manual feed / rapid traverse for all axes > EMERGENCY STOP CAMPUS V7 CAD/CAM software 1x machine license Consisting of: 1. CAMPUS NC-HOPS 2. CAMPUS MT-Manager 3. CAMPUS Workcenter 4. CAMPUS DXF interface CAMPUS NC-HOPS Graphical variant system with WOP and CAD/CAM properties for creating part variants with macro technology Automatic central lubrication Cebju Druyovhu Izorb Automatic lubrication according to defined lubrication intervals Additional sealing against dust through overpressure in each guide carriage Simultaneous lubrication for all linear guides in X, Y and Z directions, for all ball screws in Y and Z directions for all milling spindle guides

Condition: excellent (used), Boschert Compact Revo 750x1000 Trump tool system Rota Index Ball Transfer Units/Brush Tables Projection 750mm Crjbvhsn E Nfbou Izsb Machine is in a super condition which you can see in the pictures. If you have any questions about the machine, please feel free to contact us. If you are interested, we can arrange a viewing appointment.

Condition: used, mileage: 16,507 km, power: 100 kW (135.96 HP), first registration: 09/1994, overall weight: 7,490 kg, fuel type: diesel, color: red, gearing type: mechanical, total length: 6,420 mm, total width: 2,400 mm, total height: 2,800 mm, number of seats: 9, Equipment: ABS, +++ LF 8/6 on Iveco 75E14 with 620L water tank +++ Light mast +++ With partial load, see pictures MAGIRUS - Aluminum body as fire engine LF 8/6. 620-liter fire water tank. Rear pump FP 8/8 Crsbvewgg Egohu Izjb 9 seats. With seat belts, including the rear seat. Hydraulically tilting large cab. Unladen weight: 4930 kg. Gross vehicle weight: 7495 kg. Length 6.42 m / Width 2.40 m / Height 2.88 m. Auxiliary heating Height-adjustable steering wheel. 4-cylinder diesel engine with 3908 cc. Runs very well. 6-speed manual transmission. Top speed according to documents: 87 km/h. Differential lock on the rear axle. Small tow bar (2000 kg braked or 1500 kg unbraked). +++ Errors, changes, and prior sale reserved.

Condition: used, Parallel Lathe CAZENEUVE HB 575 x EP 1500 mm Between points: 1500 mm Crjbvhu Ijwgci Ijzob Maxi Ø on bench: 575 mm Maxi Ø over saddle: 300 mm Spindle diameter: Ø 51 mm Spindle speed: from 25 to 2000 RPM Turret Multifix 3-jaws chuck Ø 250 mm Threadings: Metric + Whitworth SteadiesFixed + followed TailstockCM5 Scale 2 axes ACU-RITE (Axe X defective) Lubricant pump Voltage: 380 V Length: 300 mm Width with tank: 1500 mm Height: 1700 mm Weight: approx 2,5 T

Condition: good (used), clamping plate, marking plate, measuring plate, measuring table, welding table, welding table, straightening plate, marking plate, straightening table -Clamping plate: with base frame -Clamping surface: 4400 x 2200 mm -Table height: 875 mm -Plate thickness: 30 mm Csbvev E Edmohu Izsrb -Flatness: see photos (straightening sheath not included) -Transport dimensions: 4000/2200/H875 mm -Weight: 2222 kg

Condition: as good as new (ex-display), 87565.200120, AKV403, Atlas Copco, built-in gun Crjbvhu Ievrg Iyezsb Model: 87565200120 Type: AKV403 Condition: As good as new

Condition: used, Year of construction: 2019, Used machine Year of manufacture 2019 Basic machine - DYNESTIC 7532-10.5 Automatic Dynestic table For classic nesting processing with wear plate Processing length 3100 mm Machine frame in welded construction with ground and hardened prism guides for the traveling column, aggregate head and consoles Traveling column in gantry design Rack and pinion drive, helical gears, in X and Y directions, Ball screw spindles in Z direction for precise positioning Technical data: Processing dimensions: Max. support surface on nesting table: X = 3100 mm Y = 1560 mm Max. travel distances X = 4695 mm Y = 2100mm Z = 293 mm Max. drive-over height DYNESTIC table Z = 100 mm from top edge of table (without wear plate) Maximum programmable speed Vector speed: 128.0 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min DYNESTIC table Fixed, continuous machining table with grid division, continuous grooves in X and Y direction, spacing of the grooves 50 mm with 25 meters of sealing cord for clamping the wear plate Vacuum field 1-circuit vacuum system Drilling unit 7877, 19 spindles Drive power 1.7 kW 13 vertical spindles can be called up individually Arrangement in U-shape 5+4 in X and 4 in Y direction Cebvhuovymfus Izjrb 32 mm grid Max. drill diameter: 35 mm Total drill length: 70 mm from screw end (depending on plate thickness) Spindle extension stroke: 70 mm Direction of rotation: clockwise / anti-clockwise in Change n(max.) 1000 - 4400 min-1 continuously adjustable Mounting: M 10 thread - 11 mm fit without tools, without mounting 6 horizontal spindles 2 double drilling spindles in X direction 1 double drilling spindle in Y direction Mounting: M 10 thread, 11 mm fit Total drill length max. 63 mm from screw end without tools, without mounting Milling unit 7842, Power: 12.0 kW (S6) n(max.) = 1000 - 24000 min-1 continuously adjustable, max. power at 12000 min-1 to 24000 min-1 air-cooled with HSK-F 63 tool holder with right-hand threaded nut (for right-hand rotating tools) with collet chuck with HSK shaft Ceramic ball bearing (hybrid bearing) Tool weight max. 6 kg (incl. holder) Tools: milling and grinding tools max. Ø 160 mm Safety paneling in accordance with CE standard Safety fence on the side and rear Vacuum pump 500 m³/h dry runner Personal safety through light barriers in the front area of the machine Handheld control unit for remote control of the machine with the following operating functions: > Start / stop of the machining program > Speed control of the machining cycles > Reset button > Manual feed / rapid traverse for all axes > EMERGENCY STOP CAMPUS V7 CAD/CAM software 1x machine license Consisting of: 1. CAMPUS NC-HOPS 2. CAMPUS MT-Manager 3. CAMPUS Workcenter 4. CAMPUS DXF interface CAMPUS NC-HOPS Graphical variant system with WOP and CAD/CAM properties for creating part variants with macro technology Automatic central lubrication Automatic lubrication according to defined lubrication intervals Additional sealing against dust through overpressure in each guide carriage Simultaneous lubrication for all linear guides in X, Y and Z directions, for all ball screws in Y and Z directions for all milling spindles

Condition: new, Year of construction: 2024, fuel type: diesel, power: 248 kW (337.19 HP), motor manufacturer: Perkins 1706J-E93TAG2, General information Field of application: Construction Serial number: FGWPG385EXPF00107 Crsbvhsk N Uidou Izsb Weights Empty weight: 4.103 kg Functional Generator capacity: 310 kVA Other information Fuel consumption: 46.9 Liter / Hour at 75% Load Generator: FG WILSON LL5114N Frequency: 50 Voltage: 400 Drill equipment: Tank, Battery, Control Panel, Steel canopy Emission level: Stage V / Tier IV final Water tank volume: 667 l Transport dimensions (LxWxH): 4,085x1,514x2,277 Production country: CN Additional information Please contact Kenny Bongers, Tijmen Pesselse, Arjen van Dijk or DPX Power for more information

Condition: used, mileage: 23,265 km, power: 100 kW (135.96 HP), first registration: 12/1996, overall weight: 7,490 kg, fuel type: diesel, color: red, gearing type: mechanical, total length: 6,420 mm, total width: 2,400 mm, total height: 2,800 mm, number of seats: 9, Equipment: ABS, +++ LF 8/6 on Iveco 75E14 with 620L water tank +++ with partial load, see pictures MAGIRUS - Aluminum body as fire engine LF 8/6. 620-liter fire water tank. Rear-mounted pump FP 8/8 9 seats. Cebowgg Emjvhu Izsrb With seat belts, including the rear seat. Hydraulically tilting spacious cab. Unladen weight: 4800 kg. Gross vehicle weight: 7495 kg. Length 6.42 m / Width 2.40 m / Height 2.80 m. Auxiliary heating Height-adjustable steering wheel. 4-cylinder diesel engine with 3908 cc. Runs very well. 6-speed manual transmission. Top speed according to documents: 87 km/h. Differential lock on the rear axle. Small tow bar (2000 kg braked or 1500 kg unbraked). +++ Subject to errors, changes, and prior sale.

Condition: used, mileage: 303,569 km, power: 231 kW (314.07 HP), first registration: 06/2011, overall weight: 26,000 kg, fuel type: diesel, color: grey, axle configuration: 3 axles, gearing type: automatic, emission class: euro5, Equipment: ABS, air conditioning, soot filter, Construction: HN Schörling ASF side loader type SL-VK-F, built in 04.2011, HN Schörling rear tipping construction type HFA50P, built in 04.2011, front and rear view camera, Equipment: Power steering, 2 seats, roof hatch, ABS, sun visor, electric heated exterior mirrors, electric windows, radio/CD, air conditioning, digital tachograph, rear axle differential lock, Other: First delivery in Germany, 1 previous owner, payload 10,890kg according to registration certificate, Since 1971 your reliable partner for everything to do with automobiles/commercial vehicles in 28832 Achim at the Bremer Kreuz. The Behnke Commercial Vehicle Center always has around 200 vehicles from the areas of vans, commercial vehicles and construction machinery! We offer you attractive financing options at special favorable conditions. If you are interested, we would be happy to make you an individual offer! Trade-in of your commercial vehicle/construction machine is welcome. If a new TÜV inspection is required, we would be happy to make you an offer from our partner workshops. Our offer is generally WITHOUT a new TÜV inspection. Delivery of your "new" commercial vehicle is possible through our external partners for an additional charge. Crjbvhjwfzdhsu Izjb The information provided in advertisements, on the Internet, price tags and images are non-binding descriptions and do not serve as guaranteed properties. The seller assumes no liability/warranty for typing and data transmission errors. Listed equipment may need to be checked separately. Errors and prior sale reserved.

Condition: used, Year of construction: 2019, operating hours: 7,900 h, load capacity: 1,600 kg, lifting height: 4,640 mm, fuel type: electric, mast type: triplex, Visual condition: normal, Technical condition: normal Crjbvswghlzehu Izeb

Condition: used, ADP 122 LM, Adixen, Dry Vacuum Pump Csbvetq H Apjhu Izsrb Model: ADP 122 LM Condition: Used

Condition: used, mileage: 24,477 km, power: 100 kW (135.96 HP), fuel type: diesel, gearing type: mechanical, overall weight: 3,500 kg, first registration: 02/2022, loading space length: 3,400 mm, loading space width: 2,000 mm, loading space height: 400 mm, emission class: euro6, color: white, number of seats: 6, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), Iveco 35C14 Double Cab Tipper Registered 02/2022 Platform dimensions: L 3.40 m, W 2.00 m, H 0.40 m * Wheelbase 3750 mm * Dual tires * Leaf spring suspension * Torsion bar suspension * Radio/CD/MP3 player * Onboard computer * 3-seater * Automatic climate control * Suspended driver's seat * Cruise control * Electric windows Cebvhujwggx Hj Izerb * Central locking with remote control * 6-speed transmission * Gross vehicle weight 3500 kg, payload 719 kg Sale to businesses and/or export only Subject to prior sale and errors

Condition: new, Year of construction: 2024, fuel type: diesel, power: 160 kW (217.54 HP), motor manufacturer: Perkins 1206J-E70TTAG, General information Field of application: Construction Weights Empty weight: 3.651 kg Functional Generator capacity: 200 kVA Other information Fuel consumption: 32.4 Liter / Hour at 75% Load Generator: FG WILSON LL5114F Frequency: 50 Voltage: 400 Drill equipment: Tank, Battery, Control Panel, Steel canopy Emission level: Stage V / Tier IV final Water tank volume: 822 l Transport dimensions (LxWxH): 4,085x1,42x2,367 Production country: CN Cobvhu Iek Ny Akjzsrb Additional information Please contact Kenny Bongers, Tijmen Pesselse, Arjen van Dijk or DPX Power for more information

Condition: excellent (used), Year of construction: 2021, operating hours: 1,200 h, color: other, General information Field of application: Construction Drivetrain Make of engine: Honda Weights Empty weight: 2.190 kg Functional Mast: articulated arm Lifting capacity: 230 kg Working height: 1.700 cm Condition Technical condition: very good Visual appearance: very good Other information Emission level: Stage V / Tier V Max. horizontal reach: 750 m Max swing of arm in degrees: 360 Max swing of platform in degrees: 180 Rental currency: EUR Cebvhowfnyceu Izerb Production country: IT Additional information Please contact Sales Department for more information

Condition: as good as new (ex-display), BE-5T/3NDP06 / BE 5T/3NDP06 / BE5T/3NDP06, Netzsch Monopumpen GmbH Container emptying - As good as new Cjbegynrbevhu Izerb Model: BE-5T/3NDP06 Condition: As good as new

Condition: used, ZKLF 2575-2RS-2AP, INA axial angular contact ball bearing with lifting spindle 885mm Model: ZKLF 2575-2RS-2AP Condition: Used Csbvhu Ijq S Tg Rezorb

Condition: used, 9800036875, FHA-14C-30-D200-SP230V / FHA 14C 30 D200 SP230V / FHA14C30D200SP230V, Harmonic Drive SE AC servo drive with cable Cobvhujq S T Iio Izjrb Model: 9800036875 Type: FHA-14C-30-D200-SP230V Condition: Used

Condition: used, 9800036875, FHA-14C-30-D200-SP230V / FHA 14C 30 D200 SP230V / FHA14C30D200SP230V, Harmonic Drive SE AC servo drive Crsbvhujq S T Ime Izsb Model: 9800036875 Type: FHA-14C-30-D200-SP230V Condition: Used