Used Ciata Thi-50 for sale (87,807)

Condition: used, machine/vehicle number: 11974, load capacity: 5,000 kg, lifting height: 5,500 mm, free lift: 450 mm, mast type: duplex, construction height: 4,050 mm, fork length: 2,100 mm, total length: 3,250 mm, drive type: Elektro, construction width: 3,000 mm, Four-way sideloader Chassis number: 11974 Load center: 1050 mm Dslrju D R Hujgk Ekjut ISO class: ISO class 4 = 5,000 - 10,000 kg Mast type: Duplex Technical condition: very good Front tires type: Vulkollan Front tires Size: 2-fold new Front tires Condition: 80 - 100% Rear tires Type: Vulkollan Rear tires Size: 4-ply new Rear tires Condition: 80 - 100% Battery Volt: 80V Battery Ah: 775Ah Battery manufacturer: New with Aquamatic 5PzS Battery year of construction: 2017 Battery condition: 80 - 100% Description: Travel drive 2x5kW, working hydraulics 2 x 8 kW, steering hydraulics 1x1.5kW height extended 6650 mm platform height 420 mm frame cutout 1300 mm mast extension 2200 mm The machine is sanded down repainted, all motors newly revised new hydraulic hoses and new tires, new battery with Aquamatic and charger so the machine is as good as new again Fork positioner, implement length over carrier 3950 mm fork adjustment 580-3300 mm fork tilt +/-3.5° side guide rollers on request Roof cover, Glazed cab front and rear

Condition: new, Exhibitor unit - Refrigeration dryer DRYPOINT® RA 50, the most economical way to dry compressed air - incl. level-controlled condensate drain BEKOMAT - Technical data: Volume flow (m³/h)* 51 Volume flow (m³/min)* 0.85 Volume flow ( l/min)* 850 Power consumption (kW) 0.22 Compressed air loss (deltap [g]) 0.08 Air connection G1/2 BSP-F Dimensions (mm / HxLxW) 740x345x420 Max. Max. compressed air inlet temperature (C°) 70 Min./max. operating pressure (bar [g]) 4/16 Min./max. ambient temperature (°C) 2/50 Electrical connection 230 V, 50-60 Hz, 1ph. The DRYPOINT® RA advantages at a glance * Best drying due to highly effective heat exchanger combination * Lowest pressure loss, even with varying loads * Excellent price-performance ratio * Highest efficiency, lowest energy consumption * BEKOMAT® inside * Environmentally friendly refrigerant DRYPOINT® RA: an investment that pays off Operating costs, not investment costs, determine the profitability of refrigeration dryers. Over an operating period of five years, only between 20 and 30 % of the total costs are accounted for by the pure investment. In contrast, 70 to 80 % is made up of running operating costs. One third each of these result from electricity costs, compressed air resistance in the system and compressed air losses due to leaks. The pressure drop at critical points must be compensated for by an increased compressor output and the associated additional energy requirement. Djlrgksufpzkj Ekout With DRYPOINT® RA, these operating costs can be reduced by almost half over a period of five years. The return on investment calculation shows the full potential of the new generation of refrigeration dryers: the devices pay for themselves within just six months of operation.

Condition: ready for operation (used), Year of construction: 2006, Technical data: Duolrgk Eeh It D Rjkst GUK 2nd station FA 50/2 with buckle plates

Condition: used, Functionality: fully functional, power: 36 kW (48.95 HP), fuel type: diesel, color: yellow, operation weight: 5,680 kg, Year of construction: 2021, machine/vehicle number: 2497358, Equipment: UVV, cabin, rubber tracks, standard shovel, Technical data: Engine: Diesel turbocharger Engine power: 36 kW Climbing ability: 35° Operating weight: 5680 kg Transport weight: 4798 kg - 400mm wide rubber tracks - Heating system - servo-hydraulic ISO pilot control: hammer/shear hydraulics, electro-proportional - Air-suspended, electrically heated seat - 1450mm stick - Dozer blade Duoletywpujrgk Ekot - USB and 12V connection - Control circuit for a hydraulic quick coupler 3 different buckets together with backhoe bucket 300mm #9835, backhoe bucket 600mm #9836, ditch clearing bucket hydr. 1400mm #9837, fully functional, general signs of use

Year of construction: 2008, Condition: excellent (used), I sell the press for glulam glued massive wood LISY DVORAK TH6, year 2008. Dslrgk Eekd Drhsksut Material size 3000 X 1250 x 50mm 6 working areas, manual rotation. 6 pcs hydraulic cross pressures per 1 area / pomp 1,1 KW 6 pcs manual pressures per 1 area Self weight 1200kg. Glue spreading machine LISY DVORAK NL200 included in price. Very good condition. Available immediately.

Condition: used, Year of construction: 1998, operating hours: 15,132 h, load capacity: 5,000 kg, lifting height: 4,850 mm, free lift: 1,450 mm, mast type: triplex, construction height: 2,300 mm, fork carriage width: 1,100 mm, fork length: 1,200 mm, total length: 2,780 mm, drive type: Elektro, construction width: 1,410 mm, net weight: 6,613 kg, Electric 4-wheel forklift Load center: 500 Fork width: 125 mm Fork thickness: 50 mm ISO class: ISO class 3 = 2,500 - 4,999 kg Mast type: Triplex Condition: Ready for use and fully functional Technical condition: Good Front tires Type: Non marking Djlrget Ddvhsk Ekjut Front tires Size: 355/45-15 Front tires Condition: 60 - 80% Rear tires Type: Non Marking Rear tires Size: 21x8-9 Rear tires Condition: 60 - 80% Battery Volt: 80V Battery Ah: 930Ah Battery Manufacturer: GBD Battery type: PzS Battery condition: 40 - 60% Description: overhead guard, working lights front + rear, 3rd + 4th valve to fork carriage, hand lever sideshift, fork positioner, Fork positioner ( opening range IK - IK = 100 mm - 950 mm ) 3rd valve, 4th valve, rear working lights, front working lights, full free lift, non-creeping tires, interior mirror, single pedal, seat,

Condition: used, machine/vehicle number: 9-12786, Year of construction: 1992, operating hours: 15 h, load capacity: 5,000 kg, lifting height: 5,050 mm, free lift: 2,800 mm, mast type: duplex, construction height: 3,450 mm, fork carriage width: 3,560 mm, fork length: 1,650 mm, total length: 3,560 mm, engine type: Elektro, drive type: Elektro, construction width: 2,600 mm, Four-way sideloader Chassis number: 9-12786 Load center: 825 mm ISO class: ISO class 4 = 5,000 - 10,000 kg Mast type: Duplex Condition: New machine Technical condition: Very good Front tires Type: Vulkollan Delrgksu D R Ewj Ekeut Front tires Size: 2-fold new Front tires Condition: 80 - 100% Rear tires Type: Vulkollan Rear tires Size: 4-ply new Rear tires Condition: 80 - 100% Battery Volt: 80V Battery Ah: 775Ah Battery manufacturer: New with Aquamatic Battery type: PzS Battery year of manufacture: 2023 Battery condition: 80 - 100% Description: New value 2023 / 1992 Entire machine dismantled down to the base frame and rebuilt - The truck was completely dismantled down to the base frame and sanded down. - Priming and new painting of frame and lift mast - New battery year of construction June 2023 with Aquamatik and charger latest charging technology - Lift mast completely disassembled, all rollers + bearings replaced. - Lift chains, fork adjustment chain, and steering chain replaced - All hydraulic hoses on the entire machine + lift mast replaced, list with connections and masses - All hydraulic cylinders are newly sealed - 2 front drive drums replaced - 4 trailing drums replaced - Control and electronics have been revised - New driver's seat, as well as displays, ignition lock, operating hours counter and direction switch - 2x travel motors, 2x pump motors and 1x steering pump motor completely revised - Brakes completely new, wheel drives revised. - Cabin 3-sided and roof with art glass mounted - Service complete, all oils and filters replaced - Safety and fork test - Drive 2x5kW, working hydraulics 2 x 8 kW, steering hydraulics 1x1.5kW Fork positioner, Implement length over carrier 3560 mm Fork adjustment 580-3300 mm Fork tilt +/-3.5° Side guide rollers on request 3rd valve, 4th valve, roof cover, half-cab, 2 work lights 1 rotating beacon Driver's cab 3 sides Plexiglas

Condition: ready for operation (used), Year of construction: 2005, Functionality: fully functional, overall weight: 1,850 kg, total length: 3,600 mm, total width: 1,800 mm, total height: 2,350 mm, GHD Hartmann SL-50 bread slicing machine – an automatic slicing machine. The machine is in good operational condition and have been used in a clean-room facility, 2005. Key features: - Capable of packing up to 60 pieces per minute (depending on the product) - Left-hand construction design - Stainless steel version Duslrgkevvvh Re Ekot - Equipped with an oiling system for high rye percentage bread - Product dimensions: Length: 160 - 400 mm, Height: 50 - 180 mm

Condition: good (used), Solid machine vice Manufacturer: WMW Designation: Jaws: 200 x 50 mm Clamping width: 300 mm Footprint: 580 x 190 mm Height: 150 mm Duelrgeuithiok Eket Weight: 63 kg Total dimensions: 660 x 190 x 150 mm Price: EUR 600,-- per piece (2 pieces available) Price incl. 19% VAT: EUR 714,-- per piece ( 2 pieces available) Price for 2 pieces: EUR 1.000,-- plus 19% VAT.

Condition: used, Year of construction: 1994, closing pressure 600 kN clamping plate 460x460 mm distance between columns 300x300 mm weight of the machine ca. 4,5 t lock stroke 230 mm capacity of ejector 40 kN ejector stroke 70 mm height of form 120-350 mm column diameter 56 mm Djlrgstuxmysk Ekout casting capacity 55 kN casting plunger stroke 130 m/m injection plunger diameter 45,50,55 mm casting volume (DIN 24480) 76,121,165 cm 2 volume cast pressure 345,280,231 kp/cm² casting area 174,214,260 cm 2 Traverse Stroke 150 m/m Used Die Casting machine DAW 50 without control and equipment. As a basic machine for general overhaul in the overhaul plant. It can be carried out in the scope of agreement.

Condition: excellent (used), Year of construction: 2008, Type: CNC Lathe - horizontal Manufacturer: Tsugami Type: M50SYE-III Year of manufacture: approx. 2008 Control: Fanuc 18i-TB Serial number: 5078 Hours: Control on: 94,600 h / Automatic time: 59,000 h / Feed time: 17,600 h Accessories: Standard, jaw chuck, chip conveyor, driven and rigid holders, documentation Machine condition: very good Control system: Fanuc 18i-TB Number of simultaneous axes: 5 (C, X, Z, Y, & A) Number of simultaneous axes according to export control: 4 (X, Z, Y & C) Linear axes: 3 (X, Z & Y) Rotary axes: 1 (C) Duelrovccxisgk Ekjt Parallel axes: 1 (A) Accuracy / repeatability X, Z & Y: 0.03 / 0.02 mm X-axis travel: 170 [mm] Z-axis travel: 400 [mm] Travel distance A-axis: 520 [mm] Y-axis travel: +/- 50 [mm] Diameter of the spindle passage: 51 [mm] Max. spindle speed: 6000 [rpm] Indexing accuracy C-axis: 0.001 [°] Spindle power: 7.5 / 11 [kW] Max. Counter spindle speed: 6000 [rpm] Indexing accuracy C-axis counter spindle: 0.001 [°] Counter spindle power: 7.5 / 11 [kW] [kW] Number of turret stations: 12 (all driven) Accessories: Standard, chip conveyor with pump, collet chuck counter spindle, large holder package incl. driven holders & documentation

Year of construction: 2013, operating hours: 3,707 h, Condition: used, lifting height: 6,600 mm, free lift: 2,060 mm, mast type: triplex, construction height: 2,980 mm, fork length: 2,400 mm, fork carriage width: 1,400 mm, engine type: Deutz TCD 2.9 L4, drive type: Diesel, load capacity: 5,000 kg, construction width: 1,510 mm, net weight: 7,331 kg, Diesel forklift Load center: 500 Fork width: 130 mm Duolrgket Ilq Is Eket Fork thickness: 60 mm ISO class: ISO class 3 = 2,500 - 4,999 kg Mast type: Triplex Transmission: Diesel-electric Condition: Ready for use and fully functional Technical condition: Good Front tires Type: Superelastic Front tires Size: 355/50-15 Front tires Condition: 40 - 60% Rear tires Type: Superelastic Rear tires Size: 250-15 Rear tires Condition: 60 - 80% Description: Full cab with heating, lighting similar to STVO, 3rd + 4th valve up to fork carriage, working lights front + rear, rotating beacon, 2x cross lever, single pedal Sideshift, 3rd valve, 4th valve, rear working lights, front working lights, heating, full cab, full free lift, interior mirror, exterior mirror, joystick, rotating beacon, windshield wiper, single pedal, LED, seat,

Condition: new, *TECHNICAL SPECIFICATION: Heating capacity: 9 kW Cooling capacity: 50 kW medium: water up to 90°C Max. external volume: 50 ltr at 90°C max. Flow rate 54 l/min  max. Delivery pressure 6.0 bar Dimension L x W x H 639 x 266 x 562 mm  Weight approx. 50 kg *HIGHLIGHTS EQUIPMENT: - Smart Controller Plus 7" touch / Industry 4.0 capable - Flow measurement, adjustable flow alarms - Return temperature display - Frequency converter for pump speed control with automatic mode for energy-optimised operation, or adjustable flow rate (in the operating range of the temperature control system) - Electronic pressure transducer in the flow Delrgkjftm Eio Ekout - Interface via 9-pin D-Sub connector 20mA/TTY - Connection for external temperature sensor PT 100 for measuring and displaying the mould temperature - More powerful pump, hydraulic parts made of VA, magnetically coupled - Mould draining by suction - SSR for heating control - IP54 splash water protection Visit our website for more details or for other performance classes. *This unit is compliant with the European Directives. Other directives and standards are only complied with if specified in the order confirmation. This technical specification reflects the standard equipment, customer requests deviating from the standard will be shown in quotations or order confirmations.

Condition: used, machine/vehicle number: 516049003401, Year of construction: 2006, operating hours: 3,608 h, load capacity: 5,000 kg, lifting height: 4,700 mm, free lift: 1,550 mm, mast type: triplex, construction height: 2,320 mm, fork carriage width: 1,310 mm, fork length: 2,000 mm, total length: 2,874 mm, drive type: Elektro, construction width: 1,394 mm, net weight: 7,000 kg, Electric 4-wheel forklift truck Fahrgestellnummer: 516049003401 Load center: 500 Fork width: 140 mm Fork thickness: 55 mm ISO class: ISO class 3 = 2,500 - 4,999 kg Mast type: Triplex Condition: Ready for use and fully functional Technical condition: Very good Front tires Type: Superelastic Front tires Size: 355/45-15 Front tires Condition: 60 - 80% Rear tires Type: Superelastic Rear tires Size: 21x8-9 Rear tires Condition: 80 - 100% Battery Volt: 80V Dujlotuhbzsrgk Ekjt Battery Ah: 930Ah Battery year of construction: 2012 Battery condition: 80 - 100% Description: Device is optically and technically refurbished. Maintenance renewed. UVV inspection renewed Sideshift, fork positioner, 3rd valve, 4th valve, rear working lights, front working lights, full cab, full free lift,

Condition: new, overall weight: 35,000 kg, empty load weight: 7,900 kg, maximum load weight: 27,100 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, machine/vehicle number: aaa375d3c15c697ac80fb51f9, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Rear wall with 2-leaf door division 1/2 to 1/2, with 1 slider in the right-hand leaf. With external espagnolette lock and mechanical locking at the bottom, Side walls 4 mm thick throughout, floor 5 mm thick throughout, wear and weight-optimized design, Standing platform with access, connection plate for air/electric and brake with large free space for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 Delroi Rizqogk Ekeut 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Support legs coated black Body RAL 3002

Condition: used, Year of construction: 1993, total power requirement kW weight of the machine ca. t Dujlrottcpgsgk Ekot required space m Used Rauch furnace Typ MO50E incl. used cast iron crucible and substructure. Without control cabinet heating capacity 17,5kW, 3x400V 50Hz suitable for DAW 40 and DAW 50

Condition: excellent (used), Year of construction: 2015, Sandblasting system MHG Conveyor container Doleu Iwumergk Ekout Pedestal

Condition: good (used), Good condition Can be loaded immediately Duelrjvpum Sogk Ekot

Condition: new, *Technical standard specification: Heating capacity: 9 kW Cooling capacity: 50 kW medium: water up to 160°C Max. external volume: 16 ltr at 160°C max. Flow rate 57l/min  max. Delivery pressure 6,0 bar Dimension L x W x H 780 x 305 x 705 mm Weight approx. 80 kg Delsftm Hrjrgk Eksut HIGHLIGHTS EQUIPMENT: - Smart Controller Plus 7" touch / 4.0 capable - Flow measurement, adjustable flow alarms - Return temperature display - Frequency converter for pump speed control with automatic mode for energy-optimised operation, or adjustable flow rate (in the operating range of the temperature control system) - Electronic pressure transducer in the flow - Interface via 9-pin D-Sub connector 20mA/TTY - Connection for external temperature sensor PT 100 for measuring and displaying the mould temperature - Continuous bypass of the heat exchanger with a 3-way valve to reduce deposits in the heat exchangers - More powerful pump, hydraulic parts made of VA, magnetically coupled - Tool emptying by suction - Booster pump for tool filling at high temperatures - Filling via cooling water can be switched to separate filling - SSR for heating control - IP54 splash water protection Visit our website for more details or for other performance classes. *This unit is compliant with European Directives. Other directives and standards are only complied with if stated in the order confirmation. This technical specification reflects the standard equipment, customer requests deviating from the standard will be shown in quotations or order confirmations.

Condition: used, machine/vehicle number: 7316800636, sweeping width:60 cm total power requirement:1,15 kW weight of the machine ca.:0,33 t Djlecxxuyergk Ekout dimensions of the machine ca.:0,60 x 1,40 x 1,0 m

Condition: new, overall weight: 35,000 kg, empty load weight: 6,750 kg, maximum load weight: 28,250 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, machine/vehicle number: 2f960ff7c44de83fd060ec5df, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Delji Rizfsrgk Ekeut Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in light Master Agrar design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Aluminum rear wall on pendulum bearings with double-joint hinge and with 2-leaf door division 1/2 to 1/2, top with swinging gallows, with one grain slider per door. With external espagnolette lock and mechanical locking at the bottom, Side walls 3 mm thick throughout, base 3 mm thick throughout, wear and weight-optimized design, Standing platform with ladder, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10 J

Year of construction: 1992, Condition: used, closing pressure 600 kN clamping plate 460x460 mm distance between columns 300x300 mm weight of the machine ca. 4,5 t lock stroke 230 mm capacity of ejector 40 kN ejector stroke 70 mm height of form 120-350 mm column diameter 56 mm casting capacity 55 kN casting plunger stroke 130 m/m injection plunger diameter 45,50,55 mm casting volume (DIN 24480) 76,121,165 cm 2 Duolrgofrvzvek Ekjt volume cast pressure 345,280,231 kp/cm² casting area 174,214,260 cm 2 Traverse Stroke 150 m/m Used Die Casting machine DAW 50 with SBC 2 control for the use of zinc alloys. Available from used machine stock. The machine is equipped with an electric furnace from Rauch Typ MO50E and used pneumatic sprayer 401. Recommendation from the manufacturer is some repair / general overhaul in the overhaul plant. It can be carried out in the scope of agreement.

Year of construction: 2023, Condition: new, The space requirement in the food industry is a recurring problem that we can solve with the BASIS 50-ECO horizontal cartoner! The machine is specially designed to pack the full range of different carton sizes in a small space. With a length of only 2284mm and expandable depending on the required conveyor length, it can process up to 60 folding boxes per minute. In addition, it can process a maximum size of A=220mm length, B=120mm width and H=400mm height. Our solution is based on proven technology: the Siemens control and Siemens servo drives ensure smooth processes and the Nordson glue system ensures perfect gluing of the folding boxes. We urge you: Use this opportunity to increase the efficiency of your work processes! Please contact us for further information. Duelrgomftm Nek Ekjt

Condition: used, Year of construction: 1988, Functionality: unexamined, Bruderer BSTA 50 H with 2xBBV 202/120 no CE Contact us! Dujlrgeuwl Iaek Ekst

Condition: new, overall weight: 35,000 kg, empty load weight: 5,600 kg, maximum load weight: 29,400 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², machine/vehicle number: efdaf8862775f9506d97b86a5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall pendulum-mounted with double-joint hinge and with 2-leaf door partition 1/2 to 1/2, with pivoting gallows at the top, with one grain slider per door. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Djloi Ri Ihorgk Ekeut 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 Novagr