Used Sup Elefant S15 for sale (25,077)

Condition: used, 72”x 0.5” x 60,000Lb Braner Turret Type Loop Slitting Line Braner Turret Type Loop Slitting Line is used for coil metal cross cutting with maximum width 72”, maximum 0,5” metal thcikness and 60,000Lb coil capacity Make: Braner Year New: 1996 Material Thickness: .060″ – .500″ Fgslnsrn Sqho Eybrjb Material Width: 12″ – 72″ Coil Weight: 60,000Lb Line Speed: 120 – 250 feet per minute Coil ID: 20″ – 24″ Coil OD: 75″ Slitting Cap: .500″ / 4 cuts – .125″ / 40 cuts Entry L-Type Coil Car Hydraulic Lift & Traverse Self Contained Hydraulics Control Panel Mandrel Uncoiler Powered Hold – Down Roll Outboard Bearing Support Hydraulic Feed-Up Drive Water Cooled Brake Hydraulic Peeling Table Driven Entry Pinch Rolls Adjustable Edge Guides Entry Mechanical Crop Shear Two Turret Type Slitting Heads Arbor Diameter: 12″ Powered Arbor Adjustment Powered Head Rotation Motor: 100HP DC Drive Lots of Knives & Tooling Two (2) Scrap Winders Powered Open / Close Heavy Duty Design Looping Pit Cross Over Table Drag Board Tension Stand Material Feeding Table Recoiler Hydraulic Drum Powered Push Off Hydraulic Over-Arm Separator Outboard Bearing Support 300HP DC Motor Drive Exit L-Type Coil Car Hydraulic Lift & Traverse Self Contained Hydraulics Upgraded Siemens Digital Drives, Electrics, Controls, Knives & Tooling

Condition: good (used), Year of construction: 2007, Traub TNX 65/42 Milling and Turning Center Mfd. 2007 Serial #7060107 Commissioned in 2010 TX 8i-S control (Mitsubishi/Traub based control with Mitsubishi drives and motors) 15 CNC axis’s (4) X-Y-Z turrets with 10 positions each. Up to 20 tools per turret 65 mm thru hole main and sub spindle (sub spindle has coolant flush) Foot pedal control for clamp/unclamp of spindle chucks Servo driven gantry receiver Hydraulic swivel w/ pneumatic finished part and bar remnant gripper Finished part conveyor belt RESY paper band coolant filter Knoll Coolant tank with BKW refrigerated coolant temperature control 20 Bar High pressure and 8 Bar Low pressure coolant pumps Knoll chip conveyor FMB Turbo 5-55 magazine bar feeder (new in 2010) 2) Single stick turning tool holders 2) Double stick turning tool holders 1) Cut-off tool holder 1) Overdriven double radial live ER Collet tool holder Folnsq Npqmo Eybregb 1) Overdriven radial live ER Collet tool holder 4) Radial live ER Collet tool holders 1) Radial live End Mill tool holder 1) Angle adjustable live ER Collet tool holder 2) Radial live Shell Mill tool holders 2) Axial live End Mill tool holders 6) Axial live ER Collet tool holders 43) Additional tool holders on separate list (see supplemental attachment) Hainbuch main spindle collet chuck Rohm sub spindle 2 jaw chuck 2 Spare sets of spare Z-axis ball screws and bearing packs.

Condition: excellent (used), Year of construction: 1998, Functionality: fully functional, machine/vehicle number: X17913, complete packaging line - HAYSSEN 12-16HR Technical Specifications: Output capacity : 100 bags/min Format: from 2-1,/8" x 3" x 8" x 8" to 28" long packets Includes: Foln Eysrxcn Njbrogb -VFFS bagging machine, Hayssen model 12-16HR capacity 100bags/min, depending on products and packaging sizes, sizes from 2-1,/8" x 3" x 8" x 8" to 28" long packets, with Markem Imaje, smart date 5 printer, - control panel with programmable controller, AB operator's interface monitor, 115v, 1ph/60hz, 30amps - Multihead Weigher - Hayssen Yamato scale, model ADW Dataweight, multi,head weigher, 8 stations - memory buckets, 8 g to 1000g range, with model, RCU-600 remote operator's control, swivel arm mounted, collating funnel, all stainless contact parts, 220 to 240 vac, 1ph/50/50hz, on,mild steel work platform with ladder access - Bucket Elevator - Major Packaging Machinery LTD, model 3E, bucket elevator, approx 14' to 16'high x 3' top x 4' bottom, modified with feed,belt conveyor, plastic buckets, feed chute, drive motors -Accumulation Hopper - Stainless accumulation conveyor, approx 6' x 4' x 2',deep, 2" dia legs/frame support, with wheel casters In great condition, serviced and cleaned throughout the years

Year of construction: 1998, Condition: excellent (used), machine/vehicle number: ExCello Serial Number 3888, MICHIGAN Rotoflo Type 3237 Cold Forming Machine. Fgeljfnk Ehjn Eybrsb Original Serial Number: 4590 ExCello Serial Number 3888 New 1975 rebuilt by ExCello late 1990’s Country of Origin: USA For the coldforming of profiles for serrations (straight or angular), spiral teeth, oil grooves, threads and knurls. Capacity: Maximum slide stroke 1065 mm Maximum rack length 915 mm Maximum profile diameter 50 mm Maximum profile length 125 mm Standard module range 0.3 to 1.25 Motor size 15 kW Hydraulic tank capacity 1000 l Overall floorspace width of machine 5014 mm Width of machine 2768 mm Depth with outboard support 4165 mm Height 2000 mm Approximate weight of machine 11,700 kgs Complete with: Hydraulically operated outer support assembly to accommodate part length universal headstock, Universal rack holding feature.

Year of construction: 2023, Condition: new, With bolted,welded and horizontal types, silos are used in storing cement,fly ash,bentonite and other bulk materials. Welded Silos Welded silos are preferred in low capacities of storage, it can be assembled and operated in 2 hours with one crane. It is preferred in local solutions where transportation costs can be neglected. Semix is able to manufacture welded silos in a range between 50 to 150 tons. Bolted Silos Bolted silos are preferred due to its' compactness for transportation. It can be transported with containers for avoiding freight costs. Because of its modularity, Semix is able to manufacture welded silos in a range between 100 to 2000 tons. Semix provides a mechanical supervisor for assembling the bolted silo correctly. Semix have succeed to install bolted silos in Peru, Israel, Germany and United Kingdom. Foln Eybsgau Uxoregb

Year of construction: 2008, operating hours: 1 h, Condition: used, Functionality: fully functional, machine/vehicle number: STCOS M5, Burr Oak Single Tube Cut-Off System Model: STCOS M5 Year:2007 Specifications Machine Code: LHM, SWS, 36HF, SCO, SPA, 12ROHG, ECTG Cut-Off - Tcd Standard Hitch Feed - Tcd Standard Straightener – Tcd Standard W/ Sizing Pull-Apart – Tcd Standard Coil Stand – Tcd 3 Position Over Head Uncoiler Foljv Nak Ajn Eybrogb Runout Table - Tcd 12’ Runout Table W/ Hinge Gate Supply: 480 Volts, 3 Phase, 60 Hertz Control: 110/24 Volts Extra Options The Hinge Gate Run Out Table Needs To Be Able To Switch From One Side To The Other Tooling – Tcd .500” O.D. Complete Set With 14 Straightening Rolls, 4 Sizing Rolls 6 Pair Clamp Jaws (Total), 1 Exit Guide Tube, (3) Tube Entry Bullets And Connectors .375” O.D. Complete Set With 14 Straightening Rolls, 4 Sizing Rolls 6 Pair Clamp Jaws (Total), 1 Exit Guide Tube, (3) Tube Entry Bullets And Connectors

Condition: used, Thermatool ERW Tube Mill 63mm x 2mm AEF Felnolwtz So Eybrogb 63mm x 2mm AEF / Thermatool ERW Tube Mill Make: AEF (American Electric Fusion) Tube Diameter: 15mm – 63.5mm Material Thickness: 0.5mm – 2mm Tube Length: 6 meters Double Mandrel Uncoiler Entry Shear & End Welder TIG Power Supply Vertical Accumulator Make: Kent Driven Entry and Exit Pinch Rolls Strip Guiding Unit Forming Mill Individual Gear Boxes Universal 50HP DC Motor Six (6) Forming Stand Five (5) Side Stands Welding Section Make: Thermatool Type: Vacuum ERW Design Power: 200Kw Mechanical Welding Head Beat Removing Head with Winder Cooling Tank & Pump

Condition: excellent (used), Year of construction: 2019, machine/vehicle number: 32006, input voltage: 480 V, The Sprinter for Gears with Short Face Widths up to 100 mm The 100S Gear Shaping Machine is ideally suited for small face widths, for shaping spur and helical gears, internal and external, and for crowned and tapered gears. With only 6 m2 the 100S is one of the most compact machines of its class. Equipped with: Siemens Sinumerik 840D SL Control Hydraulic System 180 Degree Load System HSK-63 Spindle Auto Stroke Adjustment Chip Conveyor Chip Basket Flexlink Automation Festo Pneumatics Rittal Panel Conditioners Chiller 480/3/60, 35 KvA Motor & Controls Specifications: Workpiece With External Gear: -Largest Module (Steel W/Approximate 600 N/mm2): 3 mm -Maximum Width: 26 mm -Maximum Diameter: 100 mm Workpiece With Internal Gear: -Largest Module (Steel With Approximate 600 N/mm2): 3 mm -Maximum Width: 26 mm -Maximum Swing Diameter: 150 mm -Maximum Internal Diameter: 100 mm Tool: -Locating Cone In The Cutter Spindle: HSK-D63 -Diameter Shaping Spindle: 85 mm -Maximum Stroke Length: 30 mm Machine Travel Distances: -Radial (X-Axis): 180 mm -Column Tilting (B-Axis): -1 - +11 Degrees Machine Workpiece Table: -External Diameter: 220 mm -Clamping Diameter: 160 mm -Bore: 63 mm Speeds: -Feed Rate X-Axis: 12,000 mm/min -Workpiece Table (C-Axis): 0-400 min-1 -Cutter (C2-Axis): 0-300 min-1 -Spindle Stroke (A-Axis): 500-3,000 min-1 Electrical Equipment: -Operating Voltage: 480V -Supply Voltage: 115V -Control Voltage: 24V -Frequency: 60 Hz -Connected Load of Machine: 35 kVA -Cable Cross-Sectional Area: 35 mm2 Fslortrvyon Eybrjgb -Protection: 80 A Machine Overall Dimensions (L x W x H): 3,380 x 3,950 x 3,015 mm Weight of Machine: 7,800 kg

Year of construction: 2011, Condition: good (used), ZPS TMZ 867 CNC Multi-Spindle SN: V867A0040 Mfd. 2011 Siemens Control PRA 100F Type: 42  With Riedel Chiller Absolent Mist Collector High Pressure Coolant Filtration system Fire Suppression System Pickup Attachment IEMCA PRA 100 Bar Loader Stock Reel and Stand Slide Pos. 3:  X- Y- Z-Axes (with Motor) Fslnjk Nb Tge Eybrogb Slide Pos. 5: X- Y- Z-Axes (With Motor) Slide Pos. 8: X- Y-Axes (to get proper center height)

Condition: used, Year of construction: 2013, #3101 Complete Brewer Scragg Mill With Slab Recovery, Gang Saw & Stackers Fgjlnswbu Dyj Eybrsb 20' 4-Strand Log Decks | Golden Eagle Slasher Saw | 2) Golden Eagle Deluxe Cabs | Primary Single Arbor Scragg Saw | Secondary Single Arbor Scragg Saw | 2) Golden Eagle Slab Edger Saw | 310-U 3 Head Under Saw | 2000 5 Head Band Saw | Side Winder Board Deduster | Super Golden Eagle 3 Head Splitter Band Saw | 4 Head Under Cut Cant Trim Saw | BR-9920 Double Arbor, 20" Bay Gang Saw System | AIT TS300 Stacker | 2) M2L Stackers | BR-4004C Double Head Notcher | Golden Eagle Chamfer | Complete Conveyors, Infeed, Rollers and outfeeds for all machines. Complete system 2013. Have videos and more pictures upon request. Price is negotiable

Condition: used, Functionality: fully functional, Year of construction: 1972, machine/vehicle number: 619336-KL, load capacity: 14,400 kg, cutting length (max.): 1,150 mm, alignment: Sí, alineado y freno independiente por eje/flecha, paper weight (max.): 900 g/m², paper width (max.): 1,850 mm, number of blades: 3, number of shafts: 12, Equipment: tail-lift, Price to be negotiated, schedule a visit without obligation. HAM-LET Brand Cutting Machine Model 1972 Incorporates a head with blades up to 73" wide to make cuts with adjustable length by means of a gear system and a variable diameter pulley. Includes 4 gears to adjust the measurement from 30cm to 115cm in length. Includes 3 circular blades with a base for additional cross cuts (variable width). The cutting capacity is ~80 cuts/min, it is capable of cutting sheets with a total thickness of 900 grs/m2. The speed of the head is adjustable, to adapt to different production rates. Includes a sheet counter (cut counter). Reinforced Beam Structure Made of high-strength beam/joist (not PTR), capable of mounting up to 12 arrows (axles or bars) for paper rolls with a total weight of 14.4ton. Each arrow has independent brakes and manual alignment, guaranteeing precise unwinding and safe. Conveyor Belt System Composed of adjustable speed belts that lead the cut paper to the elevator, in the stacking area. With alignment mechanism. Elevator with 1 ton capacity Receives and stacks the cut sheets in an orderly manner, with a mechanical aligner. Status and Availability Currently in operation and in perfect working condition. 90% of its components are original or renewed with equivalent or superior parts; 10% corresponds to adaptations that improve performance. Fgeljv Ihiqen Eybrob Constant maintenance, ready to be installed in the production line. Complete Set for Sale Includes the cutting machine, beam structure, belt system, elevator and sheet counter. Ideal for printing, cardboard and paper cutting in general (bond paper, newspaper, kraft, caple, etc.). SECTION SPECIFICATIONS Cutting Machine Brand and Year Brand and Year - HAM-LET Model 1972 - Serial No.: 619336-KL Feed and Cutting Rolls - Head for up to 73" blade - 3 Blades 73" long × 2" thick, cobalt tipped (rippling) - Rubber Roller: 75" long, with pressure/gap adjustment from cast iron roller - Cast iron roller (New): 75" long - Protective frame to prevent contact with gears, belts and pulleys) Cross Cut - Holder for 3 circular blades (includes 3 bases for mounting) Cutting Length Adjustment - Gear drive to modify the rotation ratio of the Roller with blade - 4 gears included for measurements: ~35cm, ~55cm, ~65cm, ~85cm - Belt system with variable diameter pulley (with “claws”) for precise adjustment of the cutting measurement ±20cm Motor and Controls - 15 HP three-phase motor, up to 1750RPM (semi-new) - Adjustable speed by knob (next to the elevator) - Control panel with power button, emergency stop button - Sheet or cut counter (display next to the elevator) Construction - Cast iron frame, modular and disassemblable design

Condition: new, Year of construction: 2022, Base sheet fiber laser metal cutting machine with full protection Maximum cutting area reaches up to 12000mm*2500mm, suitable for a variety of cutting options. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Cutting performance and efficiency are improved by maintaining gas flow steady with little turbulence. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. The cutting process works even at the edge of thin sheets, and ensures no chatter marks. With One-click Processing, one laser cutter is able to process multiple sheets in batches with a one-off setup, achieving batch processing. Condition: New Laser Type: Fiber Laser Laser Power: 1000W - 40000W Cutting Area: 3048*1524mm - 12500*2600mm Cutting Speed: 0-110m/min Positioning accuracy: ±0.05mm Fsln Eyehwhfqjbrsgb Repositioning accuracy: ±0.03mm Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Year of construction: 2000, Condition: used, machine/vehicle number: 30336, Article number: MA999 Manufacturer: Noble Type: Micromat 203 Year of construction: 2000 Machine number: 30336 Control: CNC he 1904 Length [mm]: 1500 Width [mm]: 1250 Height [mm]: 1650 Weight [kg]: 1600 Power supply: 380V Foln Eybjdacqhsrsgb Working hours [h]: 1858 Positioning range x/Y/Z [mm]: 760 X 310 Cutting force [to]: 20 2 piece of multimedia tools / 3 x / 6 x with various tools Accessories: manual / schematics

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. Fsln Eybsrtrzdorsgb The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Depth of Taper: 8" Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Condition: used, Year of construction: 1999, sheet width 3000 mm plate thickness 3 mm weight of the machine ca. t 3 support arms 1 angle stop Felnsr Ngtie Eybrogb pneumatic hold-down device Backgauge to be operated by hand

Condition: reconditioned (used), Deckel FP5 NC Toolroom Milling Machine Model: FP5 NC Original Year of manufacture: 1986 Control: DECKEL DIALOG 4 Table Area: 1000 x 550mm 'X' axis Travel: 710mm 'Y' axis Travel: 600mm 'Z' axis Travel: 500mm Fgjlnswhwhbs Eybrob Spindle Taper: SK 40 Spindle Speeds: 18 - 6300 RPM Spindle Power 7.5 kw 380V - 3 PHASE Machine Weight = Approx 3665 kg's Control cabinet = Approx 460 kg's Splash Cabinet = Approx 300Kg.s The machine is in very good working order. The splash cabinet is included and has been partially restored. New Linear bearings have been fitted for all the door rails & some of the internal panels have been Re-Powder coated. This machine has not had a lot of run hours for its years and still quite a very nice machine. Note: Machine Is currently fitted with Vertical spindle Head. Machine has capability for use with Horizontal milling attachment, however the Horizontal Spindle support arm is not included. The Horizontal Spindle arbors and spacers are however included.

Year of construction: 1998, Condition: like new (used), Used Kleiser GmbH approximately 16sqmt horizontal shell and tube heat exchanger. Unit has (68) 316L stainless steel tubes approximately 3,000mm long x 25mm outside diameter, rated 6 bar design pressure at 100 deg.c. 316Ti stainless steel shell approximately 3,000mm long x 324mm diameter, rated 6 bar design pressure at 100 deg.c. (2) 316Ti stainless headers. Unit has 2 support mounts. Fgjlsh Agxhjn Eybrjb This heat exchanger is located at Perry Process Equipment Ltd UK site. It has recently been pressure tested on both sides. Please contact us for further details or to arrange a site inspection of the unit. Process Equipment Ltd buys and sells high quality used and refurbished process equipment worldwide. We have equipment in stock, immediately available, and can save you considerable time and money on your process equipment. Global Support is available; Perry has warehouses in the UK, USA, Poland, Czech Republic, Russia and Ukraine to support our customers worldwide. View our entire inventory of process equipment on our website and request a no-obligation quotation on any of our items.

Condition: new, Year of construction: 2022, All-round sheet fiber laser metal cutting machine Equipped with automatic functions of nozzle changing and one-click processing, P-Series is competent for all cutting demands. Flake graphite in the cutting machine bed improves greatly the shock absorption and wear resistance, and residual stress almost disappears after age hardening, therefore, precision and lifetime of the equipment are improved, and costs saved. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. The fully closed-loop control adjusts according to feedback to ensure that the actual motion position is consistent with the theoretical input value. With One-click Processing, one laser cutter is able to process multiple sheets in batches with a one-off setup, achieving batch processing. Condition: New Laser Type: Fiber Laser Laser Power: 1500W - 30000W Cutting Area: 3048*1524mm - 6100*2500mm Cutting Speed: 0-169m/min Fgslnshwhf Ao Eybrsb Positioning accuracy: ±0.03mm - ±0.05mm Repositioning accuracy: ±0.02mm - ±0.03mm Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: good (used), Year of construction: 1973, FELLOWS 70-15 GEAR SHAPER - Model 70-15 Fellows heavy duty vertical gear shaping machine , suitable for the manufacture of external straight spur gears up to 70" pitch diameter, as well as internal spur gears and splines within a range of 0" to 88" pitch diameter, regardless of shaper-cutter radius. This unique feature, combined with the machines 15" face-width capacity and 1.7DP cutting capability in steel, provide a formidable platform for producing a wide range of larger geared part members. Equipped with: * Machine Main Base With Work-table, Upper Column, Cutter Ram and Slide of "Super Robust" Construction * Machine with "Saddle Backoff" Method of Cutter Relieving * Cutter Spindle 6.25" diameter w/Standard Straight Spur Guide * Cutter Positioning via Stroke Jog-Button * Rapid Rotation of Work Spindle for Trueing Work-Piece * Rapid Saddle Traverse for Traversing Saddle Relative to Work * Automatic Depth Feed Mechanism for One to Four Cuts, With 4 Speed Motor Providing Speed Change on Finishing Cut * Assorted Work and Feed Change Gears * Assorted Stroke Change Gears * 2" Riser Plate * Main Drive Motor 15HP, 650/220 rpm, 240 Volt 60Hz w/Westinghouse Rectifier Unit for AC * Power Forced Lubrication to Working Elements with "Lubriquip Lub Controller" * Coolant Tank, Pump, and Piping, With Chip Pan * Full Complement of Electrics * Assorted Guards, Covers * 84" T-Slotted Table * Hydraulic System * Work Lamp * Work Platform * Cutter Adaptor * Manuals Specifications: Max. Diameter External Gear Cut (Nominal): 70" Max. Diameter Internal Gear Cut (Nominal): 88" Max. Diameter Workpiece Accommodated: 104" Worktable Diameter: 84" Max. Permissible Weight of Workpiece & Fixture: 36,000 Lbs. Max. Distance Workspindle Centerline to Centerline of Cutter Spindle: 35" Min. Distance Workspindle Centerline to Centerline of Cutter Spindle: 0" Max. Work & Fixture Clearance Height w/Cutter Spindle in Upper Position: 28" Max. Diametral Pitch (full length teeth): 2 DP Max. Diametral Pitch (stub teeth): .75 DP Max. Diameter Pitch (30P.A. splines): 2-5/5 DP Diameter of Cutter Spindle: 6.25" Max. Stroke Length: 19.118" Max. Face-Width (nominal): 15" Stroking Speeds (infinitely variable): 5 to 122 S.P.M. Max. Infeed of Cutter Ram: .0020 inch/min. Min. Infeed of Cutter Ram: .0005 inch/min. Folnsrtrxio Eybrogb Max. Rotary Feed Per Stroke (per 1" of cutter diameter): .0068"/Min. Min. Rotary Feed Per Stroke (per 1" of cutter diameter): .0006"/Min. Approximate Machine Dimensions: 192"L x 144"W x 150"H Approximate Machine Weight: 95,000 Lbs.

Year of construction: 1997, Condition: used, Used Comi Condor type HX/GMP 316L stainless steel Atex rated horizontal peeler centrifuge. Unit has 1150mm diameter perforated basket. Maximum load 280kgs, maximum cake capacity 222 litre. Internal rated +0.5/-0.5 bar design pressure at 50 deg.c. Unit has main drive, hydraulic powerpack, mounting springs and (2) control cabinets. Fgslnjiwyr Ao Eybreb Process Equipment Ltd buys and sells high quality used and refurbished process equipment worldwide. We have equipment in stock, immediately available, and can save you considerable time and money on your process equipment. Global Support is available; Perry has warehouses in the UK, USA, Poland, Czech Republic and France to support our customers worldwide. View our entire inventory of process equipment on our website and request a no-obligation quotation on any of our items.

Condition: new, Year of construction: 2022, Entry-level sheet fiber laser metal cutting machine Lower laser cutting cost and easy operation The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Condition: New Laser Type: Fiber Laser Fgolshwrgtjn Eybrsb Laser Power: 1000W, 1500W, 2000W, 3000W Cutting Area: 3000*1524mm Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Cutting Speed: 0-100m/min Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: refurbished (used), Perry is offering a high quality, refurbished, used Winkworth model RT400 316 stainless steel high speed ploughshare mixer. Manufacturer: Winkworth Material: Stainless steel Serial Number: 16025 Capacity: 400 litre (product dependent) Fgoln Eyotz Tkpjbreb Mixing trough: 1,300mm long x 800mm diameter Discharge Type: Centre bottom pneumatically operated flap discharge value Type Of Blades: Ploughshare blades Motor: 11kw, 380-415 volt, 3/50, 1450-1460rpm motor through Custom Power Transmission gearbox type MO820, 11kw Revolutions Per Minute: 99rpm with 14:1 ratio Also includes: (1) stainless steel side entry chopper driven by 4kw, 380-415volt, 2840-2870rpm, 3/50 motor. Refurbishment Shot blasted all mild steel parts and bead blasted all stainless external parts. Overhauled gear-box with new bearings and seals with oil change. Overhauled chopper assembly with new bearings and seals. Serviced packed glands with new PTFE packing. Fitted new flanged bearings on to shaft ends. Re-gasketed chamber, access hatch and valve. Spray painted in our paint booth facility. Reassembled and test run. Perry has been supplying this type of equipment for decades. You can rely on getting a first class service from the Perry Equipment Group.

Condition: new, Year of construction: 2024, All-round fiber laser metal tube cutting machine Multiple function options help the laser tube cutting machine be used in numerous tube cutting processes. The slender nozzle allows the laser tuber cutter to avoid interference and cut various types of tubes, including special-shaped tubes like H-Beam, P-Beam, I-beam, etc. Cutting machine clamping becomes convenient, easy and fast, with 3 seconds at the soonest to clamp and high repeat precision Cutting performance and efficiency are improved by maintaining gas flow steady with little turbulence. BodorGenius, combined with the lightning-quick piercing process, completes the whole piercing during it moves down on Z-axis. Thanks to the technology, no reworking is necessary for medium and thick sheet piercing. Angle steel and channel steel cutting are standard with no need for additional installation. Optimized edge searching method and algorithm guarantee higher cutting precision and better steadiness of the laser cutter. Condition: New Fgsln Eybshwrlxoreb Laser Type: Fiber Laser Laser Power: 1500W, 2000W, 3000W, 6000W Maximum machinable tube length: 6500mm/9200mm Chuck drive types: NC electric chuck Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: new, Year of construction: 2024, Laser power: 6000W/12000W/20000W Applicable Material: metal Condition: New Laser Type: Fiber Laser Cutting Area: 3000*1500mm Cutting Speed: 200m/min Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT Cooling Mode: WATER COOLING Certification: CCC, CE, GS, ISO, Sgs Laser Source Brand: IPG/MAX Weight (KG): 11000KG Warranty: 3 years Power supply: 110V/220V/380V 50Hz/60Hz 1. Flagship Series Super dynamic responding, easily handle complex patterns of sheets. 2. Automatic Edge-finding Felnjg Tu N As Eybregb With the capability of identifying irregular sheets, the edge searching time is decreased to 3 seconds. 3. Automated Nozzle Changer The machine changes its nozzle within 35 seconds at the fastest speed - this saves 50% of time costs.

Condition: new, Year of construction: 2024, Entry-level sheet fiber laser metal cutting machine Lower laser cutting cost and easy operation The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Condition: New Laser Type: Fiber Laser Cutting Area: 3000*1500mm Cutting Speed: 0-40000mm/min Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT Cutting Thickness: 0-30mm CNC or Not: Yes Foln Eyehv Hkaobrogb Cooling Mode: WATER COOLING