Screw compressor COMPAIR LS 11, 11 kw

Condition: excellent (used), Year of construction: 2017, operating hours: 1,437 h, functionality: fully functional, machine/vehicle number: 137949-100, clamping force: 2,100 kN, screw diameter: 65 mm, displacement volume: 913 cm³, injection pressure: 1,600 bar, overall weight: 10,500 kg, controller model: UNILOG B8, The machine was serviced and upgraded to the latest standards by the manufacturer in 2021! It has not been used since and is therefore in very good condition! The machine is offered complete with 2 Kistler modules for cavity pressure control! TECHNICAL DETAILS Plastic type: Thermoset Clamping force: 2,100 kN Screw diameter: 65 mm Screw stroke: 275 mm Screw L/D ratio: 22 Max. screw speed: 278 rpm Lhjdpfjyi Ailex Ahwjc Screw torque: 1,920 Nm Tie bar spacing (HxV): 670 x 620 mm Mold installation height: 350 mm Platen daylight: 1,100 mm Opening stroke: 750 mm Ejector stroke: 200 mm Ejector force: 65 kN Theoretical shot volume: 913 cm³ Specific injection pressure: 1,600 bar Max. plasticising rate: 62 g/s Nozzle stroke / nozzle force: 400 mm / 100 kN Free-shot injection rate: 419 cm³/s Barrel heater power: 27 kW Number of heating zones incl. nozzle: 5 MACHINE DETAILS Control system: UNILOG B8 Hydraulics Hydraulic oil tank capacity: 600 liters Oil temperature min/max (HLP 32): 30 °C / 40 °C Oil temperature min/max (HLP 46): 40 °C / 50 °C Oil cooling activation temperature (HLP 32): 35 °C Oil cooling activation temperature (HLP 46): 45 °C Electrical Drive power hydraulic pump: 37 kW Max. screw barrel temperature: 350 °C Cooling water system Cooling water consumption: approx. 0.5 - 1.5 m³/h Max. cooling water supply temperature: 35 °C Cooling water return: max. 10 bar Ambient temperature: °C Noise level: 65 dB(A) Weight: 10,500 kg Operating hours: 1,437 h EQUIPMENT Kistler module for cavity pressure control, range 1: 20,000 pC Kistler module for cavity pressure control, range 2: 10,000 pC

Condition: used, Year of construction: 2008, Technical details: bore capacity in steel (diameter): 40 mm throat: 350 mm bore stroke: 120 mm bore capacity in cast iron: 60 mm spindle taper MT: MK 4 spindle throat: 350 mm spindle speed:: 50 - 1450 / 18 step U/min Ljdpfx Aheviqybowohc feed: automatisch/manuell mm/U Distance spindle/table max.: 25 - 705 mm table clamping surface:: 430 x 430 mm drill table adjustment: 680 mm column diameter: 150 mm distance spindle center to floor plate:: 1210 mm total power requirement: 1,6 kW weight of the machine ca.: 350 kg dimension machine xH: 0,95 x 0,55 x 2,3 m Height-adjustable table(swivel and tilt adjustable ) Table can be swiveled 45° left/right and rotated 360° around the column Thread cutting up to M24 Coolant system A vise is mounted, and a threading device is included with this machine. *

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: H2X396F51535, Year of construction: 2015, operating hours: 6,533 h, load capacity: 8,000 kg, lifting height: 3,500 mm, mast type: duplex, power: 72 kW (97.89 HP), empty load weight: 16,230 kg, TECHNICAL DETAILS Load capacity: 8,000 kg Lifting height: 3,500 mm MACHINE DETAILS Mast type: Duplex Power: 72 kW Net weight: 16,230 kg Dimensions: 380x230x325 cm (H) Lhodpfoyifkpsx Ahwjc Operating hours: 6,533 h EQUIPMENT Solid rubber tires

Condition: ready for operation (used), Year of construction: 2000, machine/vehicle number: 0-201-22-3325, functionality: fully functional, workpiece length (max.): 5,800 mm, workpiece width (max.): 1,200 mm, controller model: Homatic-CNC System PC83 mit Windows NT 4.0, feed rate X-axis: 80 m/min, spindle speed (max.): 18,000 rpm, No minimum price – guaranteed sale to the highest bidder! Bidding obligates the buyer to collect the machine on 20/03/2026! 4-axis CNC machining center for drilling, milling, edge banding, and finishing: - Saw and crosscutting unit for tool changer - Drilling and milling unit (4 spindles) for tool changer - Combination flush-trimming and finishing unit for tool changer - Blow-off nozzle for workpiece edge, compatible with tool changer Attention: Except for the units listed above, no vacuum suction cups, tools, or tool holders (even if visible in images) are included in the scope of delivery! TECHNICAL DETAILS Console clamping table "K": 12 adjustable consoles for holding vacuum cups with longitudinal and lateral stops, 4-fold occupancy - Max. workpiece length (single occupancy): 5,800 mm - Max. workpiece length (pendulum mode): 2,200 mm - Max. workpiece width: 1,200 mm - Max. workpiece thickness (using standard 100mm-high cups) with edge: 60 mm (if extraction hood is in position 1) - Max. workpiece thickness (using standard 100mm-high cups) without edge: 60 mm - Max. workpiece thickness (using standard 100mm-high cups) without edge: 120 mm (if extraction hood is in position 2) Support equipment - Drilling head: 17 vertical spindles - 2x main spindle 12 kW, water-cooled, for HSK (speed 18,000 rpm with C-axis and 12-position carousel tool changer) - Separate Y-axis for second main spindle and interface for aggregates with integrated pneumatic and electrical connections - Electronic supply and swivel drive - C-axis: swivel range without limitation Edge banding unit, 360°, for insertion into right main spindle - Max. edge height: 65 mm - Pickup station right, for depositing edge banding modules - Pre-cutting station and 3-position roller magazine Adapter units Lhedpfxsyic Tus Ahwjc - Combination flush-/radius trimming and finishing unit (profile scraper knife) - Saw and crosscutting unit - 4-spindle drilling/milling unit (crosshead) - Blow-off nozzle for workpiece edge MACHINE DETAILS - Control: HOMATIC control PC 83 with Windows interface (NT 4.0) EQUIPMENT - WOODWOP programming system, version 5.0 - Network connection - Laser positioning aid - Chip conveyor - Safety: pressure-sensitive floor mats at front, side safety cage; rear: wall installation Note: A loading aid can be provided for a deposit of €5,000. Upon return, the deposit will be refunded minus 10%.

Condition: good (used), Year of construction: 1998, machine/vehicle number: 0618012, Offer 24604 Technical data: - suitable for welding steel, aluminum, special metals, Cr Ni, etc. - welding current 450 A 60% ED - 360 A 100% ED - welding current adjustable from 3 A - 450 A - Synergic setting control FRONIUS - water cooling device FRONIUS - separate wire feed case - intermediate package device - wire feed case 1 linear meter - 4 rollers wire feed continuously adjustable - MIG - MAG hose package water-cooled approx. 4 linear meters - ground cable - pressure reducer - mobile base frame - connection 400 V / 6.6 A / 8.7 kVA Ljdevncubepfx Ahwjhc space requirement approx. W 650 x H 900 + 450 x D 1100 mm - weight approx. 200 kg

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2019, operating hours: 7,866 h, load capacity: 2,000 kg, lifting height: 130 mm, fork length: 1,000 mm, overall weight: 866 kg, TECHNICAL DETAILS Load capacity: 2,000 kg Load center distance: 600 mm Load distance: 1,023 mm Lift: 130 mm Fork inner dimensions: 55 / 172 / 190 mm Fork outside distance: 560 mm Fork length: 1,000 mm MACHINE DETAILS Tyres: Polyurethane + Drive wheel size: 230 x 75 mm Load wheel size: 2 x 85 x 80 mm Support rollers (drive side): 140 x 54 mm Track width (drive side): 495 mm Track width (load side): 388 mm Travel speed with load: 7.5 km/h Travel speed without load: 9.0 km/h Lifting speed with load: 1.4 m/s Lifting speed without load: 1.4 m/s Lowering speed with load: 0.9 m/s Lowering speed without load: 1.2 m/s Gradeability with load: 10 % Gradeability without load: 20 % Acceleration time over 10 m with load: 6.9 s Acceleration time over 10 m without load: 5.4 s Service brake: electromagnetic Dimensions & Weight Dimensions (L x W x H): 2,333 x 720 x 1,305 mm Lodpfx Aeyiancjhwshc Weight: 866 kg Battery voltage: 24 V Rated capacity: 240 / 360 Ah Battery weight ± 5%: 220 / 290 kg Operating hours: approx. 7,866 h EQUIPMENT Integrated charger Display with charge level and operating hours

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 91656748, Year of construction: 2021, operating hours: 2,364 h, load capacity: 3,000 kg, overall weight: 560 kg, total length: 1,275 mm, total width: 600 mm, TECHNICAL DETAILS Towing capacity: 3,000 kg Rated tractive force: 600 N Wheelbase: 930 mm Axle load unladen front: 330 kg Axle load unladen rear: 230 kg Lhedpoyiafzjfx Ahwec MACHINE DETAILS Dimensions & Weight Coupling height: 158 mm Dimensions (L x W): 1,275 x 600 mm Coupling height: 158 mm Weight: 560 kg Ground clearance in wheelbase center: 50 mm Turning radius: 1,080 mm Motor / Battery Drive motor power S2 60 min: 2.8 kW Battery voltage: 24 V Nominal capacity: 250 Ah Battery weight: 220 kg Travel speed with load: 9 km/h Travel speed without load: 10.5 km/h Tractive force with load: 600 N Tractive force without load: 600 N Tractive force: max. 2,000 N Brake: electromagnetic Operating hours: approx. 2,364 h EQUIPMENT Charger

Condition: good (used), Year of construction: 2015, Metal cutting Tooling TOS - HUR 50 MACH-ID 2923 Lodjwvht Repfx Ahwshc Make: TOS Type: HUR 50 Year: 2015

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 511909V00010, Year of construction: 2019, operating hours: 3,097 h, load capacity: 1,700 kg, lifting height: 5,750 mm, free lift: 1,880 mm, mast type: duplex, empty load weight: 2,390 kg, TECHNICAL DETAILS Load capacity: 1,700 kg Load center: 600 mm Load distance: 410 mm Wheelbase: 1,453 mm Free lift: 1,880 mm Lift height: 5,750 mm Ledpfx Asyh Ik Njhwohc Fork dimensions: 50 / 100 / 1,150 mm Fork carriage: ISO 2.328 A/B Fork carriage width: 760 mm Fork outside distance: min. 316 / 620 mm MACHINE DETAILS Mast type: Duplex Dimensions & weight Dimensions (L x W x H): 2,499 x 1,140 mm Unladen weight: 2,390 kg Length incl. fork back: 1,349 mm Overhead guard height: 2,200 mm Seat height: 1,140 mm Support arm height: 308 mm Mast extended height: 6,320 mm Width between support arms: 790 mm Battery/Voltage/Capacity: 48 V / 620 Ah Operating hours: approx. 3,097 h EQUIPMENT UVV: 09/26 Blue Spot rear Operator's manual

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 516329X00173, Year of construction: 2020, operating hours: 981 h, load capacity: 5,000 kg, power: 15 kW (20.39 HP), empty load weight: 5,176 kg, The forklift has only 918 operating hours! TECHNICAL DETAILS Load capacity: 5,000 kg MACHINE DETAILS Unladen weight: 5,176 kg Drive power: 15 kW Battery voltage: 80 V Operating hours: 981 h EQUIPMENT Charger The following technical data is taken from the listing. The seller assumes no liability for its accuracy! Mast type: TELE (two-stage mast) Mast designation: TELE 2550 Closed height (h1): 2,550 mm Free lift: 160 mm Rated lift height (h3): 3,480 mm Maximum lift height (h4): 4,487 mm Basic load capacity: 4,999 kg Load capacity at rated lift height (3,480 mm): 4,999 kg Load capacity at maximum lift height (4,487 mm): 4,990 kg Fork carriage: 6 rollers, FEM A Width: 1,200 mm With fork wear protection Forks: Length: 1,600 mm Cross-section: 130 × 60 mm Mounting: FEM A Driver's compartment / Cabin Overhead guard (driver’s safety canopy): Height approx.: 2,322 mm Storage: Storage tray / compartment in cabin area Mirrors: Interior rear-view mirror as a panoramic mirror Hydraulic controls: Mini lever (4-function) Driver’s seat: Type MSG65 comfort seat Fabric upholstery Restraint system: EasyBelt (seat belt system) Lsdpfoyh H Nkox Ahwshc Drive control: Single pedal control Ignition lock: Lock 530 Electrics / Lighting / Safety Front work lights: LED work lights Mounting position: on driver’s overhead guard, top, left and right Rear work light: LED work light Mounting position: on driver’s overhead guard, top, right Warning light: Flashing beacon on driver’s overhead guard, switch operated Warning system: STILL Safety Light front and rear Assistance system: Speed reduction dependent on steering angle (steering angle speed limit) Vehicle connector: 320 A DIN 43589, Schaltbau, version LV

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 516220V00288, Year of construction: 2019, operating hours: 5,918 h, load capacity: 1,600 kg, lifting height: 3,180 mm, free lift: 150 mm, fork length: 1,200 mm, TECHNICAL DETAILS Load capacity: 1,600 kg Load center: 500 mm Load distance: 374 mm Wheelbase: 1,319 mm Free lift: 150 mm Lift height: 3,180 mm Fork length: 1,200 mm Fork thickness: 40 mm Fork width: 80 mm Fork tine length: 800 mm Fork carriage width: 980 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 2,661 x 1,099 x 2,160 mm Weight: 3,125 kg Height with mast extended: 3,742 mm Overhead guard height: 2,035 mm Seat height: 1,058 mm Coupling height: 473 mm Axle load with load front/rear: 4,160 / 565 kg Axle load without load front/rear: 1,500 / 1,625 kg Mast type: Duplex Lhodpfxoyh Hy Ae Ahwsc Battery voltage/capacity: 48 V 625 Ah Operating hours: approx. 5,918 h EQUIPMENT UVV 05/26 Charger Side shifter Seat heating Blue Spot front and rear 2x LED headlights front, 1x rear Front windshield with wiper Heater Panoramic roof Digital display Interior mirror Operator's manual

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 516220V00311, Year of construction: 2019, operating hours: 5,505 h, load capacity: 1,600 kg, lifting height: 3,180 mm, free lift: 150 mm, mast type: duplex, fork length: 1,200 mm, TECHNICAL DETAILS Load capacity: 1,600 kg Load center: 500 mm Load distance: 374 mm Ledpfsyh Hqbsx Ahwehc Wheelbase: 1,319 mm Free lift: 150 mm Lift: 3,180 mm Fork length: 1,200 mm Fork thickness: 40 mm Fork width: 80 mm Fork tine length: 800 mm Fork carriage width: 980 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 2,661 x 1,099 x 2,160 mm Weight: 3,125 kg Mast height extended: 3,742 mm Overhead guard height: 2,035 mm Seat height: 1,058 mm Coupling height: 473 mm Axle load with load front/rear: 4,160 / 565 kg Axle load without load front/rear: 1,500 / 1,625 kg Mast type: Duplex Battery voltage/capacity: 48 V 625 Ah Operating hours: approx. 5,505 h EQUIPMENT Charger Exchangeable battery Side shifter Heated seat Blue Spot front and rear LED headlights 2x front, 1x rear Front window with wiper Heater Panoramic roof Digital/Display Interior mirror Operator's manual Note: The seat is worn.

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: W42377N00009, Year of construction: 2024, operating hours: 8 h, load capacity: 800 kg, mast type: triplex, fork length: 1,500 mm, overall weight: 1,995 kg, Stacker with only 8 operating hours! TECHNICAL DETAILS Load capacity: 800 kg Fork length: 1,500 mm Lift height: 2,800 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 2,200 x 820 x 2,260 mm Weight: 1,995 kg Lhodpfjyh E Ekex Ahwoc Mast type: Triplex Battery voltage / capacity: 24 V / 500 Ah Operating hours: approx. 7.3 h EQUIPMENT Charger Hydraulic carton clamps Side clamps (1,150 mm length) Operating manual (digital in PDF format)