Lowbed

Fliegl VTS 400

Condition: used, empty load weight: 9,980 kg, maximum load weight: 30,020 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 02/2022, loading space length: 10,200 mm, loading space width: 2,520 mm, loading space height: 950 mm, suspension: air, tire size: 235/75R17.5, color: grey, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 4 axles, SAF axles, turntable, air suspension, ABS (anti-lock braking system), extendable to 3m, lashing points, 2-part loading ramps, hydraulic ramps, side aluminum fender, twin tires, wheel recesses. Njdjzg Ev Ujpfx Amujlc Superstructure: 4-axle low-bed trailer with wheel recesses, excavator arm recess, and hydraulic ramps, in like-new condition! 4x 10t SAF axles, drum brakes, total weight technically 40,000 kg, loading length of the gooseneck approx. 2800 mm, loading length of the low-bed platform approx. 7400 mm, extendable to 3000 mm, 50 mm drawbar eye, 1st pair of wheel recesses approx. 1600 mm long, 2nd pair of wheel recesses approx. 600 mm, ramp length approx. 3850 mm, ramps are hot-dip galvanized, ramps can be hydraulically shifted sideways. Loading height of the front wheel recess approx. 560 mm! Loading height of the rear wheel recess approx. 650 mm! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Custom-tailored transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Further information Chassis Steel welded construction Turntable with robust ball bearing, storage box recessed Turntable extension Foldable rear support 2 wheel chocks with holder Aluminum side impact protection Mud flaps at the rear across the entire width Extendable wideners to 3,000 mm (not in rear slope) (However, the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the center of the loading area Wooden planks 70 mm for widening to 3000 mm Tie-down eyes, low-loader type 3 pairs of tie-down points, each rated at 10 tons, integrated in the front of the floor 6 pairs of tie-down anchor plates, top and side in the outer frame, each rated at 10 tons 1 x in the neck area the rest distributed in between with a maximum distance of 1200 mm 1 x rear slope 5 pairs of pocket slots recessed in the outer frame, inside 70 x 40 mm, (can be converted to 5-ton ring tie-down eyes, not included in the scope of supply) Towing device, turntable trailer Tow bar with tested 40 mm towing eye Note! With a 40 mm towing eye, the permissible total weight of the truck must not exceed 18000 kg; otherwise, a 50 mm towing eye is required. Axles + Suspension SAF drum brake axles Axle / chassis laser-aligned, reducing tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization in the front and rear (rocker equalization) Wheels & Tires 235 / 75 R 17.5, according to manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be pulled by towing vehicles which guarantee the effectiveness of the ABS! Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connecting cable 1 LED rotating beacon with holder, switched via parking light (beacon can be removed) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area: steel floor followed by 70 mm softwood floor, steel / diamond plate in the wheel arch area Rear slope with 70 mm softwood floor Access Ramps Steel ramps, 2800 mm long, 750 mm wide, laterally movable covered with wood with gas spring support Operating Instructions With an axle load of 10,000 kg, an exemption permit is required, only indivisible loads are possible!!! The stated total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle / support and saddle loads. Nledpfx Amji Ri I Esusc Country of Registration / Signs Country of Registration: Germany 1 with Dekra inspection and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for license plate holder, two-line Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paint finish Frame: RAL 3002 Carmine Red 10-year warranty against rust-through Tow bar: galv

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 14,300 kg, maximum load weight: 9,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, loading space height: 900 mm, total length: 12,000 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Further Information Chassis Steel welded construction Turntable with robust ball bearing Foldable rear support 2 wheel chocks + holder Aluminum side underrun protection Splash guards at the rear over the entire width Quarter panel fenders in front of the 1st axle Excavator arm recess starting above the rear axles to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess on the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box recessed in the gooseneck in the floor with a lid, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the gooseneck in the low-loader wheel well area, sloped for access, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area is 400 mm higher than the wheel recess. 2nd pair of wheel recesses between the axles recessed in the low-loader in the wheel well area, sloped for access, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in the main beam area is 300 mm higher than the wheel recess. Wheel recess cover pull-out from the main frame, with wood inserts. Distance from the outer frame, beam to beam, approx. 1280 mm Extensions pull-out to 3,000 mm, foldable at the wheel recess extensions (extension not in the rear slope and not in the wheel recesses at the bottom) Storage compartment for wooden planks in the middle of the loading area or under the loading area, depending on technical feasibility Wooden planks 70 mm for extension to 3000 mm Lashing points, low-loader 1 pair of ring lashing points recessed at the front on the gooseneck, each 5 tons 8 pairs of lashing eyes at the top and on the side recessed in the outer frame, each 10 tons 2 x at the front on the gooseneck 6 x in the low-loader, the first lashing point 250 mm from the front and the last one max. 250 mm from the rear, the distance between the lashing points is no more than 1100 mm 5 pairs of ring lashing points recessed in the outer frame, each 5 tons (can be converted to stake pockets) Coupling system, trailer, turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Axles + Suspension SAF drum brake axles Axle/chassis laser-aligned, reducing tire wear and fuel consumption Air suspension with lifting and lowering valve, can be operated separately at the front and rear Wheels and tires 235/75R17.5 according to manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake Trailer Info Center for displaying vehicle data such as axle load (no calibrated scale) and odometer Axle load detection via EBS-CAN bus signal, for display on the display in the cab, truck must be suitably prepared, no truck installation (no calibrated scale) Vehicle-driving stability system Duomatic connection at the front, with connecting cable to the towing vehicle EBS, Electronic Braking System with EBS plug at the front, with connecting cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical system Nodji Ri I Nopfx Amujlc 24 Volt, multi-chamber lights in LED with resistor, yellow LED lighting on the side, license plat

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, overall weight: 24,000 kg, axle configuration: > 3 axles, loading space height: 900 mm, total length: 11,940 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Additional Information Low-bed semi-trailer chassis Steel welded construction Turntable with heavy-duty ball bearing ring Folding rear outriggers 2 support wedges with holder Aluminum side impact protection Rear splash guards covering the entire width Semi-fender for 1st and 2nd axles with anti-spray splash guards behind each axle, anti-spray splash guards in front of and behind the 3rd and 4th axles Excavator arm recess above the rear axles, extending to the rear, approximately 1800 mm long, approximately 650 mm wide and approximately 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess, laterally on the longitudinal frame, approximately 300 mm from the front and approximately 200 mm in front of the rear slope 1 plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with a padlock (lock not included) 1 storage box recessed in the gooseneck at the bottom with lid, W=720 mm/ L=520 mm / D= 170 mm Extendable widening elements to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading platform Lashing eyes for low-bed trailer (40 lashing options) 1 pair of lashing eyes on the gooseneck, each 5 tons 9 pairs of lashing eyes embedded above and on the side in the outer frame, each 10 tons 2 x at the front on the gooseneck 7 x in the low bed 6 pairs of lashing eyes in the outer frame from the low bed, each 5 tons (for attaching tie-down straps) 3 pairs of folding lashing eyes additionally, each 10 tons 1 x inside next to the main frame at the beginning of the low bed 1 x on the gooseneck (protruding) 1 x behind the last axle, recessed in the floor Coupling device for the trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined by 8° / D-value min. 160 kN Axles + Suspension Drum brake axles Parabolic spring suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization at the front and rear (rocker equalization) Wheels and Tires 235 / 75 R 17.5 according to the manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connecting cable Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking lights (beacon removable) 2 pairs of warning signs double LED illuminated and extendable to 3,000 mm Floor Gooseneck at the front with steel / checkered plate covering followed by 70 mm softwood floor, wheel arch area with steel / checkered plate covering Rear slope with 70 mm softwood floor Nljdpfxei Ri Dae Amuoc Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable covered with wood Hydraulically operated via towing vehicle auxiliary drive with throttle, operation on the left-hand side at the front Hydraulic connection with SVK plug NW 10/3, incl. connecting hose Country of Registration / Signs Country of Registration: Germany 24/7 Service Hotline prepared for two-line license plate holder Contour marking with reflective strips ac

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT44001000966, empty load weight: 9,400 kg, maximum load weight: 30,600 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 10/2010, loading space length: 7,145 mm, loading space width: 2,750 mm, loading space height: 900 mm, total length: 12,120 mm, total width: 27,500 mm, total height: 900 mm, suspension: steel, tire size: 235/75 R17,5", color: red, The images shown are archive photos! Permissible / technical gross weight: 24,000 / 40,000 kg Permissible / technical payload approx.: 14,600 / 30,600 kg Permissible / technical axle load: 24,000 / 40,000 kg Unladen weight (basic version) approx.: 9,400 kg +/- manufacturing tolerance Overall length approx.: 12,120 mm Overall width max.: 2,750 mm Neck length approx.: 2,850 mm Low bed platform length in wheel track area incl. rear bevel approx.: 7,145 mm Rear bevel length approx.: 850 mm Frame width approx.: 2,750 mm Loaded bed height in low bed approx.: 900 mm Drawbar height approx.: 950 mm Drawbar length approx.: 1,700 mm Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection 1 plastic toolbox, Extendable width up to 3,250 mm (not at rear bevel) (track width of machine/vehicles to be transported must not exceed outer frame width of 2,750 mm) Storage compartment for wooden boards in the center of the loading area 70 mm wooden boards for extension to 3,000 mm 2 pairs of stake pockets in the low bed recessed into the longitudinal beams Lashing points low-bed: 2 pairs of lashing eyes on neck, 5 tons each 1 pair of lashing eyes in rear bevel 4 lashing eyes recessed in the middle of the floor 2 pairs of keyhole profiles in wheel track area for insertion of longitudinal guide rails and as additional lashing option 6 pairs of lashing pins recessed in outer low-bed frame, 10 tons each 5 pairs of stake pockets recessed in the outer frame of the low bed 4 additional pairs of 10 ton lashing eyes: - 1x on neck - 3x recessed in low bed floor Trailer towing device, turntable design Drawbar with certified 50 mm towing eye Nlodpjyxq A Hsfx Amuec Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber mounts and mechanical axle load equalization front and rear (rocker balancing) Wheels and Tires 235/75 R 17.5" Steel twin wheels, factory silver finish Brake System 2-line compressed air brake system Spring-loaded parking brake 2 foolproof couplings at front, with interconnecting lines to tractor ABS and ALB, with ABS socket at front and connection cable Note: The trailer may only be towed by vehicles ensuring proper ABS functionality! Floor Neck area with steel / checker plate covering Followed by 70 mm softwood floor; in wheel arch area steel / checker plate Rear bevel with 70 mm softwood floor Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, with wooden covering Hydraulically operated via tractor auxiliary drive Operating Notes At 10,000 kg axle load, an exemption permit is required, only indivisible loads permitted! Note! Oversize length and width require a permanent special permit. When applying for an exemption for regulated heavy haulage, an axle load indicator is required for air-suspended vehicles! This applies to any deviation from § 34 StVZO (axle and permissible total weight overrun), which requires an exemption under § 70 StVZO. The specified gross weight is technically possible; depending on the load, the total weight permitted by axle, support, and kingpin loads may not be achieved. (Poor driving or tracking behavior may occur due to improper load distribution) The images shown are archive photos!