Used Trime Light Tower Hybrid for sale (23,394)

Condition: new, overall weight: 35,000 kg, empty load weight: 6,750 kg, maximum load weight: 28,250 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, machine/vehicle number: 2f960ff7c44de83fd060ec5df, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in light Master Agrar design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Aluminum rear wall on pendulum bearings with double-joint hinge and with 2-leaf door division 1/2 to 1/2, top with swinging gallows, with one grain slider per door. With external espagnolette lock and mechanical locking at the bottom, Side walls 3 mm thick throughout, base 3 mm thick throughout, wear and weight-optimized design, Standing platform with ladder, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Cjln U D Dji Rizfshogt Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10 J

Year of construction: 2018, Condition: new, Witron Wibond Information Systems Pick-Vision-System Paperless picking We have taken over the remaining materials from Wibond. In addition to the offers below, we also offer repairs to your Wibond assemblies - please feel free to enquire without obligation! Several 100 pieces of various modules available WIB-P-10010 PKK 1 RGB WIB-P-10011 PKK 7 RG WIB-P-10015 PKN 4 RGB WIB-P-10016 PVI WIB-P-10067 PVI-T V2.0 Feed_Barrier with Verpo WIB-P-10098 PBM WIB-P-10099 PBM E WIB-P-10101 PKK 1 RGB WIB-P-10108 PKN 4 RGB WIB-P-10118 PKN 2 RGB WIB-P-10134 PKA 5 RGB FB WIB-P-10137 PKN 5 RGB WIB-P-10138 PKS 2 RGB F WIB-P-10139 PKN 4 RGB S2 WIB-P-10141 FB RJ45 adapter PCB WIB-P-10149 PMC 3, PMC V3.2 Celepm Exqjn U D Dhogt WIB-P-10151 PKN 4 RGB WIB-P-10200 PKK 1 RGB WIB-P-10254 PKN 4 RGB S2 WIB-P-10257 PKS 2 RGB WIB-P-10298 PKA 5 RGB S2 WIB-P-20247 PVI WIB-P-20248 PVB WIB-WKS-8849 WITRON - Komanz V5.x with acknowledgment button, WIB-WKS-8859 WITRON - Komanz V5.x with acknowledgment button, WIB-WKS-9063 WITRON - connection without plug WIB-WKS-9800 WITRON - Komanz V7.x with acknowledgement button, WIB-WKS-9803 WITRON - Komanz V7.x with acknowledgement button, WKS-9806 WIB-U2-20152 DIC-ECM-I, used Corridor Display double sided EZ.138.5701S Church hymn displays: different versions of hymn displays and input devices

Condition: as good as new (ex-display), different Schölly Flexilux fiber light guides - Ringlight Cgelsfr T Ihen U D Dhjt - Gooseneck - single arm Prices from € 100,-- single) to € 350,-- (ring) prices are EXW, bulk discount possible

Condition: used, Functionality: fully functional, Polymer Laboratories PL-ELS 2100 Evaporative Light Scattering Detector. The Polymer Laboratories PL-ELS 2100 Evaporative Light Scattering Detector for semi-volatile and non-volatile compounds. The PL-ELS 2100 features unique patented gas control, allowing evaporation of high boiling solvents at very low temperatures. Features of Polymer Laboratories PL-ELS 2100 Evaporative Light Scattering Detector: -High sensitivity for semi-volatile compounds -Compatibility with a wide range of solvents -Low temperature operation (even for 100% water) -Extremely low dispersion for high resolution separations -Compact design -High eluent flow rates: up to 5 ml/min -Rapid equilibration -Simple and easy to setup and operate -Ideal for high throughput screening -Eliminates the need for derivatization steps for selected analyates -Improved uniformity of response across a solvent gradient Good working condition. Please check out our other listings as well. Csloua E Sben U D Dhegt

Year of construction: 2020, Condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. Coln U D Djfz Ndyohjgt

Condition: new, Year of construction: 2023, operating hours: 0 h, machine/vehicle number: 0, Strojplast hybrid packaging system for wood briquettes Structure of the packaging system offered here: - Downstream of an RUF briquetting system. - Packaging system incl. stacking and label dispenser - Vacuum lifter for 12 packages (one layer), facilitates stacking of the wrapped packages on pallets - Pallet wrapper - Strojplast offers turnkey solutions for the packaging of wood briquettes. - Manual to fully automatic solutions are available on a modular basis. - For all common wood briquette formats up to 6 to/h - Color RAL 7031, RAL 7040, powder coating - Operator language: German / English (others on request) All systems are assembled in the manufacturer's factory and extensively tested for function. Only then, or after pre-acceptance, are they dismantled in modules and shipped to the customer, thus avoiding time-consuming and cost-intensive time-consuming and costly assembly/commissioning on the customer's side. - Delivery time: approx. 4-5 months, depending on version - Price and further information on request ----- Strojplast hybrid packaging system for wood briquettes Structure of the packaging system offered here: - Downstream of an RUF briquetting system. - Packaging system incl. stacking and label dispenser - Vacuum lifter for 12 packs (one layer), facilitates stacking of the wrapped packs on pallets - Pallet wrapper - Strojplast offers turnkey solutions for the packaging of wood briquettes. - Manual to fully automatic solutions are available on a modular basis. - For all common wood briquette formats up to 6 tons per hour - Color RAL 7031, RAL 7040, powder coating - Operator language: German / English (others on request) All systems are assembled in the manufacturer's factory and extensively tested for function. Only then, or after pre-acceptance, are they dismantled in modules and dispatched to the customer, thus avoiding time-consuming and cost-intensive time-consuming and costly assembly/commissioning on the customer's side. - Delivery time: approx. 4-5 months, depending on version Cgeln U D Doqculfohjt - Price and further information on request

Condition: new, overall weight: 38 kg, empty load weight: 3 kg, maximum load weight: 34 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, machine/vehicle number: 1f4581c873ed977cb9602039b, Further information Chassis semi-trailer container Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Container mounts: 1 x 20 foot centered (or swap body container 7.15 / 7.45), not retractable at the front, the pivot pins of the container lock in the longer version 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Side collision protection Coln U Dsi Rixks Dhogt Aluminum underride guard Half-shell mudguards with anti-spray flaps according to EG VA drip tray with 1 1/4 inch drain pipe + 1 1/4 inch stopcock, incl. drip tray, with perforated tread plates, approx. 400 mm wide, left + right between drip tray and side member 4 hose trays approx. 4500 mm long (hose box) for hose pipes 2 x DN 200 outside + 2 x DN 160 centrally arranged, rear hose box (stainless steel) 300 mm deep, splash-proof, cover (stainless steel) with rubber seal all round, with drain hole at lowest point, then without cover on hose pipes 1 stainless steel earthing lug at the rear in FR on the right of the frame, with international earthing sticker on the frame, Steps at the rear right on the underride guard, at the rear in FR right on the outside of the main beam, tread plate approx. 260 mm long and 300 mm wide, Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored cable routing for easy servicing Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) This vehicle may only be loaded with 20' tank containers that comply with ISO 668 and in particular ISO 1496-3! The tank containers must have "end-load-transfer areas"! Country of approval / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Approval according to ADR acc. to 9.1.1.2 of ADR, EX/II, EX/III / certificate of approval for vehicles for the transport of certain dangerous goods (ex.B3) with warning sign at the rear, not valid for substances according to UN 0331 and 0332 (explosives B-E) Contour marking with refle

Condition: good (used), 500 ST EURO standard container, light gray used for sale unit price 9,00€ Dimensions: L800xW600xH325 mm/Material PE Side walls and base closed Recessed grips on the ends Material: Polyethylene (PE) Csln U D Deqxbi Hjhsgt

Condition: as good as new (ex-display), Schölly Flexilux Mercury vapor Light Source 2000W White/UV selectable Cjln U Dofr T Hvo Dhjgt prices are EXW

Condition: used, Functionality: fully functional, Polymer Laboratories PL-ELS 1000 Evaporative Light Scattering Detector. Laboratories is a completely new design of high sensitivity Evaporative Light Scattering (ELS) Detector for HPLC, microHPLC and GPC/SEC. This ELS detector has replaced the RI for the detection of solutes with no UV chromophore, giving enhanced performance with the benefits over an RI of improved sensitivity, excellent baseline stability, gradient compatability, and providing a positive response for all solute/solvent combinations. Features: -Small footprint for laboratory convenience Cgeln Ujt Uk Dmj D Dhjt -Improved sensitivity -Low dispersion -Excellent baseline stability -Wide gradient compatibility -Rapid equilibrium -Detection of even relatively volatile compounds -The PL-ELS 1000 from Polymer Good working condition. Please check out our other listings as well.

Year of construction: 2020, Condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. Csln U D Doflrc Sohogt the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Condition: as good as new (ex-display), Year of construction: 2015, Functionality: fully functional, Equipment: type plate available, The Discovery Series Hybrid Rheometer (DHR) HR3 is a state-of-the-art instrument designed for accurate and reliable rheological measurements. Featuring innovative technologies such as a patented drag cup motor, magnetic bearing, and a force rebalance transducer, it delivers exceptional precision in controlling strain, stress, and normal force. The DHR is equipped with a True Position Sensor to ensure superior accuracy, and its versatile Smart Swap geometries and temperature systems offer unmatched flexibility. Whether for routine testing or advanced research, the DHR HR3 stands as one of the most advanced, adaptable, and user-friendly rheometers available today. Cgeln Uovfl I So D Dhet

Year of construction: 2020, Condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? Coln U Defz A H Do Dhsgt You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Condition: used, Nearly new tires with rims for sale! The Outrigger IN240 55D17.5 All the tires in our lineup are nearly new and in excellent condition. Ready for field use for your machines. Contact us for a stock list with a wide range of tires with rims for your machines. We are available for your inquiries. Give us a call or request more information by filling in the form. We'll be in touch with you. Cgsln U Dewaiz Ds Dhjt

Condition: ready for operation (used), Year of construction: 2007, A TAG folding machine for the production of Z-Line filters is available. Folding width: 1000mm, folding height range: 20mm-147.5mm, folding knife curves: 50 and 100, folding capacity: 20-70 folds/min, connected load: 7kW. Machine dimensions X/Y/Z: approx. 2100mm/2000mm/1000mm, weight: approx. 2500kg, control: Siemens. Documentation available. On-site inspection is possible. Cgsln Uov N I Ate D Dhot

Condition: good (used), Automatic creasing and folding machine Dumor Lightning Fold Pro 8336B+33KF The device is fully functional, ready to work. Like new. Year of production 2019. This is the most efficient creasing and folding system on the market, solid construction. Vacuum feeding from a high stack. Built-in vacuum and suction system. The set includes an instruction manual. The 7” color Smart Screen programmer allows for very easy machine setting. Technical parameters: Paper thickness: 0.15-0.35 mm Feeder capacity: 100 mm Accuracy: +/- 0.5 mm Format range: 140×160mm, 330×650 mm Paper type: coated, uncoated, laminated, UV varnished, photo Creasing bar width: 1.0 mm, 0.6 and 1.4 mm Speed: 6300 sheets/hour (A4/1 fold) Number of creasing strokes in one pass: up to 32 times (creasing only mode) Control: double 7-inch touch screen Predefined fold types: 7 types + any user folds Number of folds: 1 or 2 Cgjln U Devkt Tme Dhot Folding method: knife folding Automatic paper length measurement: YES High-performance upper feeder suction: YES Patented breaking knife system: YES Creasing depth adjustment: YES Weight 280kg,

Condition: excellent (used), Year of construction: 2019, operating hours: 100 h, machine/vehicle number: CONX-3257, total length: 2,800 mm, total width: 1,000 mm, total height: 1,160 mm, type of input current: AC, input voltage: 380 V, This machine came to us barely used one year ago and we have used it just twice in that time. Reason for sale is change of mind on how we laminate/coat or media. The quality is amazing and in perfect working order. This can be demonstrated on site. Cgeln U D Dsqpfayohjt

Condition: new, Year of construction: 2024, Italtower Orus lighting tower Lighting : 4 x 320 watt LED lights Lighting mast : 9 meter / manually operated Cgoln U Dst I Utrs Dhst The Orus is very compact... With a surface of a euro-pallet... Ask our sales department for a demonstration at your location....

Condition: new, Year of construction: 2024, Italtower Street Plug-in lamppost Lighting : 4 x 160 watt LED lights Lighting mast : 5,5 meter / manually operated Cgoln Ujt I Uq Rs D Dhjt The Street Plug-in is the lighting column that does not need stamping.... Ask our sales department for a demonstration at your location....

Condition: new, Year of construction: 2024, Italtower Towerloop mobile light tower Lighting : 4 x 160 watt LED lights Lighting tower: 7 meter / manually operated Cjln U D Dot I Um Sehogt You can connect the Towerloop in series... Ask our sales department for a demonstration on your location....

Condition: new, Year of construction: 2024, fuel type: diesel, Italtower Mantis mobile light tower Cgslnst I Ulnj U D Dhet Compact, robust and lightweight, that's the Mantis lighting tower. Lighting : 4 x 320 watt LED lights Diesel engine : Yanmar 2TNV70 / 1500 RPM Fuel consumption : 0,55 liter per hour Ask our sales department for a demonstration for our Mantis.

Condition: new, Year of construction: 2024, fuel type: diesel, Italtower Okapi Pro mobile light tower Cgslnst I Ukwo U D Dhst The Okapi Pro is the robustly built mobile box light tower. Usable for many applications and economical in energy consumption.... Lighting : 4 x 320 watt LED lights Diesel engine : Yanmar 2TNV70 / 1500 RPM / water cooled Ask our sales department for a demonstration at your location....

Condition: new, Year of construction: 2024, Italtower Astrid Pro mobile light tower 4 x 320 watt LED lights The 1500 RPM Yanmar diesel engine has a fuel consumption of only 0.55 liters per hour.... You can connect the Astrid Pro in series thanks to the switch main generator. This halves your fuel consumption... Ask our sales department for a demonstration at your location.... Cjlst I Ukqsn U D Dhjgt

Condition: new, Year of construction: 2024, Italtower Full Solar mobile light tower Cgjlnjt I Uhio U D Dhot Over 1200 watts of energy per hour is generated by the solar panels.... Working emission free ? And still 4 x 100 watt LED lights of mobile lighting ? Ask our sales department for a demonstration on your location....

Condition: new, Year of construction: 2024, Italtower Street Solar light tower Illumination : 60 watt LED light / 6,000 lumens Autonomy : up to 10 days.... Emission : zero Cgeln U D Dot I Ufushet Ask our sales department for a demonstration at your location....