Used Bimak 35 Au/C for sale (84,367)

Condition: used, overall weight: 35,000 kg, empty load weight: 6,927 kg, maximum load weight: 28,073 kg, axle configuration: 3 axles, first registration: 07/2016, tire size: 385/55 r19,5, machine/vehicle number: 5a722b71e07e463c6c5370ad2, Further information Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Note! With a frame neck height of 30 mm, the truck wheelbase must not exceed 3700 mm! Outer frame slightly slanted with Load-Lock profile for attaching lashing strapsNote! To attach the straps in conjunction with drop sides, the drop sides must be opened! Not in the neck area! 10 pairs of additional lashing eyes embedded in the outer frame, 2.5 tons each, outer frame with Load-Lock profile for attaching lashing strapsNote! Cannot be used with drop sides! 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation, folding supports at the front in front of the bulkhead can be extended outwards and folded down. Moved inwards as far as possible when driving. (for unhitching under load), without supports, pull-out ladder at the rear, door locks at the side, wheel chocks with holder, aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of the first axle and behind each axle, with anti-spray flaps behind each axle, rear impact protection Heavy blocker rear transverse impact protection, heavy-duty pallet stop on both sides, approx. 20-25 mm high, with lashing option every 200 mm, loading height reduced by approx. 20-25 mm, plastic toolbox SAF disc brake axles, air suspension, without lift axle 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable front coupling heads, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, vehicle stability system 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front 2 white/red lane departure warning lights at the rear, 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Floor: Front area steel floor with anti-slip coating, screen printing plates approx. 30 mm thick, cross joints with Omega inlay, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg, steel/ checker plate covering in the wheel area. Front bulkhead/front stanchions: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, bottom inside at approx. 140 mm height with steel impact protection Middle stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and long pocket at the bottom, 3 pairs of stanchion positions, aluminum insertion slats Rear steel corner stanchions up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Dcelijkyrlwskd Ncog Tarpaulin with welded-in horizontal and vertical straps, stainless steel tensioning fasteners, customer lettering on rear portal Roof: sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white, EcoLift - lifting roof can be raised by approx. 380 mm, with gas pressure damper support, anti-ice system, with a hose in the middle, with automatic ventilation Approval country: Germany, test approval according to EC 2007/46, load securing certif

Year of construction: 2007, Condition: good (used), frame press GOMA PHA 3500 Door Press hydraulic Location Gorzów Wlkp. Dcslikdodntc Nj Nceg Conditions of delivery OWN RECEIVING Cost of delivery to be negotiated Startup type to be negotiated Description Comments Working space 3500 x 2300 mm 1000kG (daN) pressure, engine at hydraulic unit 2,2 kW lenght 3500 mm hight 2300 mm weight 2000 kg agrageate hydraulic

Condition: as good as new (ex-display), Year of construction: 2024, operating hours: 10 h, Functionality: fully functional, machine/vehicle number: 8046723D038, spindle motor power: 11,000 W, turning diameter over cross slide: 380 mm, spindle speed (max.): 3,000 rpm, overall weight: 2,000 kg, type of input current: three-phase, total width: 1,800 mm, total length: 2,500 mm, total height: 1,800 mm, torque: 373 Nm, Equipment: documentation/manual, CNC LATHE STYLE 350 [850 dbc] - main spindle motor power 11kW - main spindle bore Ø54 mm, 3,000 rpm - manual universal with 3 jaws D200mm - VDI30 turret with 8 positions - Coolant gun, including high-pressure pump - Work area lighting (LED) - Cooling system - Automatic lubrication Dcelikevvwbled Ncog - Ball screw protection - Full fairing with sliding doors - Speed potentiometer - Coolant control button - Handwheel - Remote support on machine – allows remote diagnostics

Condition: like new (used), Year of construction: 2004, machine/vehicle number: SN:N7383, For sale is a Nicholson A2/35" 5 arm air bellows (890mm). Dcjliksvmqpksd Ncog The machine is being sold completely overhauled and repainted. If you are interested, please contact us for further information.

Condition: used, Double picking station feeder. Designed to serve production lines of drilling, squaring, edging, squaring, pantographing, sanding and painting without operator supervision. Fully automatic not need for manual adjustments during the manufacturing process Working dimensions: * Maximum length: 3000 mm * Maximum width: 1300 mm * Automatic double station panel unloading system. * Work capacity 13 minute cycles Dcolikd Njqvt Ecocsg * Panel gripping system via motorized arm with suction cups with vacuum drive system TECHNICAL DETAILS TO BE CHECKED

Condition: used, Functionality: fully functional, Year of construction: 2018, load capacity: 4,500 kg, Telescopic forks Dcslikdsvbmtzs Ncjg ISO class: ISO class 3 = 2,500 - 4,999 kg Condition: Ready for use and fully functional Technical condition: good Description: Year 2018 ISO 3A (51 cm) Capacity 4500 kg / 600 mm Opening range 1200-2350 mm ID OS1418

Condition: new, Year of construction: 2024, pressing force: 135 t, throat depth: 450 mm, operating speed: 10 mm/s, bending length: 3,020 mm, retraction speed: 140 mm/s, warranty duration: 12 months, Equipment: safety light barrier, Standard Equipment - Y1, Y2, X, R axes - European type segmented blade and die - European type segmented blade and die holder - Heavy Type Front Gauges for 175 Tons and Above - 10″ Esa S 630 touch 2D programmable 4-axis control unit - Greater throat depth 450 mm - Higher cylinder stroke distance 350 mm - Hoerbiger or Rexroth hydraulic system - Foot pedal with emergency stop button. - Front support arms. - Side and rear door security guards Technicial Specifications TWIST LENGTH (MM): 3020MM BENDING CAPACITY (TON): 135TON LANDING SPEED (MM/sec): 160 MM/SN RUNNING SPEED (MM/sec) 130 MM/SN STROKE: 320 MM THROAT DEPTH: 450MM Dcjlsvgadksikd Ncsg LENGTH : 3745 MM WIDTH : 2280 MM PLATE HEIGHT: 2835 MM MAIN ENGINE: 15 KW WEIGHT : 9600 KG

Condition: used, Year of construction: 1998, Brushing machine for elements brand Camam model C/1N/1S serial number 98001 year of construction 1998 branded CE powered 380V 4.5 Kw 13 A ground 530 Kg. complete with declaration of conformity and manual of installation and d. Djlikolagc Sod Ncecg

Condition: excellent (used), Year of construction: 2014, Automatic double head saw ELUMATEC DG 244 + E 355 YEAR 2014 The proven elumatec "Cut from below" principle: This ensures free access to the support tables Dslsm H Udbjikd Ncecg The large diameter of the saw blade and its optimal use guarantee the right cutting performance in all cutting variants For elumatec, it goes without saying: the ability to cut to the outside dimension in all angle settings. This eliminates the need to carry out different length calculations for profiles of different heights. A huge advantage for special angles The universal pivoting and tilting of the saw unit allows you to cut tall and wide profiles and make all types of cuts that require a two-plane tilt. Thanks to this, many profiles can be cut without the use of supports Protective covers Serially equipped with saw blades Dosing spray devic

Condition: ready for operation (used), Year of construction: 2011, Functionality: fully functional, machine/vehicle number: 181721, clamping force: 350 kN, screw diameter: 18 mm, displacement volume: 25 cm³, ejector force: 20,100 N, ejector stroke: 105 mm, pressure: 2.2 bar, TECHNICAL DETAILS Clamping force: 350 kN Opening stroke: 205 mm Ejector stroke: 105 mm Ejector force: 20.1 kN Injection unit Screw diameter: 18 mm Max. stroke volume: 25 cm³ Max. screw speed: 450 rpm Dcsljunldhsikd Ncsg Max. current screw speed: 450 rpm Injection flow: 52 cm³/s Injection flow increased: 40 cm³/s Specific injection pressure: 2,200 bar Specific injection pressure increased: 2,193 bar Nozzle travel: 530 mm Nozzle contact pressure: 28.6 kN MACHINE DETAILS Machine weight: 6,700 kg L x W x H: 6 x 1.5 x 2.5 m

Condition: reconditioned (used), Chocolate refiner year 1998 rollers overhauled in 2017 Dslikovkqrgod Ncecg

Year of construction: 2020, Condition: like new (used), Photo description Dslikdsppyzlo Ncscg

Condition: new, Year of construction: 2024, saw blade diameter: 350 mm, cutting capacity: 90 mm, cutting range round at 90°: 90 mm, total length: 9,700 mm, total height: 1,750 mm, total width: 2,360 mm, cutting speed: 100,000 mm/min, overall weight: 4,160 kg, cutting range square at 90°: 80 mm, motor voltage: 4,000 V, warranty duration: 12 months, Equipment: rotational speed infinitely variable, Product Features Fully automatic angle saw machine, PLC Controlled color touch screen, Servo-controlled material drive Vertical cutting system with ball screw and servo motor controlled vertical cutting system moving on Mausura type linear guideway, Possibility to set variable cutting speeds (slow at material entry, fast at intermediate section, slow again at exit), Special patented system that eliminates saw tooth backlash; eliminates vibration and resonance caused by saw tooth backlash, preventing saw breakage and extending saw life 20 to 100 rpm inverter speed adjustment, Servo motor controlled material sliding and resting system, Possibility to cut 10 different lengths on the same material, Length adjustment with an accuracy of ±0.3 mm (depending on the runout of the saw used, this value may increase), Dcelikdot Ewh Hj Ncjg Micro spray lubrication system that allows cutting to be done with special oil instead of oil, Cutting Capacity Makismum Saw Diameter 350 mm Saw Angle 90° Round Material Diameter (max.) Min. 15 - Max. 90 mm Square Material (max.) Min. 15x15 - Max. 80x80 mm Rectangular Material (Max.) Min. 15x15 - Max. 80x80 mm Min Last Remaining Fire Length 50 mm Min. Cutting Length 100 mm Cutting Capacity Main Voltage 400 V Control Voltage 24 V Installed Power 8 kW Current 29.2 A Saw Motor 4 kW Pumping Pump 0.09 kW Air Pressure 6 kg/cm2 (240 l/min) Saw Speed 20 - 100 By Inverter Angle Rotation 90° Saw Features Saw Diameter 350 mm Saw Core Diameter 40 / 50 mm Pin Holes 2 x Diameter 11 TiN Coating Medium Hard Steel TiCn Coating High Stiffness Steel TiAIN Coating Stainless steel Dimensions Width 9700 mm Length 2360 mm Height 1750 mm Net Weight 4125 Kg Gross Weight 4160 Kg

Condition: used, fuel type: diesel, Lugli lift, diesel, 6 ton capacity Delikd Njtxdpfececg

Condition: excellent (used), Year of construction: 2006, Functionality: fully functional, machine/vehicle number: 586, MODEL C/A4 SCIVOLO 70 YEAR OF MANUFACTURE - 2006 CHASSIS NUMBER - 586 Dsliou Nvhzokd Ncjcg ENGINE TYPE - DIESEL

Year of construction: 2006, Condition: refurbished (used), HYDRAULIC PRESS MECAMAQ PRESSURE 350t Dcjlisfmqqlekd Ncjg STROKE 350mm TABLE LEFT RIGHT 600mm TABLE FRONT BACK 750mm POWER 15kw Dimensions: Height: 2,9m Width: 1,9m Length: 1,3m Weight: 5.700 kgr

Condition: ready for operation (used), Functionality: fully functional, Year of construction: 2011, operating hours: 7,800 h, machine/vehicle number: WLHZ1076TZK055270, TECHNICAL DETAILS Operating Hours Operating hours: approx. 7,800 h Chassis Dimensions Undercarriage transport width: approx. 3,000 mm Chassis centerline (Taurus): approx. 2,280 mm Chassis length: approx. 4,600 mm Boom and Stick Hydraulic boom: 3,600 mm Stick length: 3,050 mm EQUIPMENT - Without bucket and without SMP - 20% wear on the running boards - Defective discs - see photos - Full hydraulic hoses present - Taurus condition commensurate with age Further technical data according to the manufacturer - without guarantee Engine Power according to ISO 9249: 95 kW / 129 hp at 1,800 rpm Djlikd Nowgm Izocecg Engine type: Liebherr D 934 S according to Stage IIIA / Tier 3 Fuel tank capacity: 290 l Automatic idle: sensor-controlled Hydraulic system Hydraulic pump: Liebherr variable-displacement swashplate pump Flow rate: max. 300 l/min Operating pressure: max. 350 bar Pump control and regulation: Liebherr Synchron Comfort System (LSC) with electronic maximum load control, pressure cut-off, minimum lift control, demand flow control, swing circuit priority and torque control Hydraulic tank capacity: 175 l Hydraulic system capacity: max. 290 l Control system Power distribution: via control spools with integrated safety valves, simultaneous and independent operation of the chassis, swing, and attachment Equipment and swing operation: with proportional joystick levers Travel operation: with proportional foot pedal for travel drive Additional functions: via switches or proportional foot pedals Swing Drive: Liebherr swashplate oil motor with integrated Brake valve and torque control Transmission: Liebherr compact planetary gearbox Slewing ring: Liebherr, internally toothed, sealed single-row ball bearing slewing ring Slewing speed: 0 – 9.0 rpm, continuously variable Slewing torque: 42 kNm Undercarriage Drive: One Liebherr swashplate oil motor on each side of the undercarriage with brake valves acting on both sides Transmission: Liebherr compact planetary gearbox Travel speed stage I: 2.4 km/h Travel speed stage II: 5.0 km/h Tensile force: max. 175 kN Undercarriage: B60L, maintenance-free Track rollers/support rollers per side: 8 / 2 Track shoes: 3-grouser Track tension: hydraulic Dimensions Height: 3.1 m Length with folded boom: 8.7 m Undercarriage height: 1.1 m Digging depth: 6.4 m Reach at ground level: 9.7 m

Condition: ready for operation (used), Year of construction: 1991, Functionality: fully functional, feed length X-axis: 140 mm, feed length Y-axis: 100 mm, feed length Z-axis: 300 mm, spindle speed (max.): 1,500 rpm, controller model: IBH CNC, TECHNICAL DETAILS Axial slide travel Z-axis: 300 mm Radial slide travel X-axis: 140 mm Cutter travel Y-axis: 100 mm Tailstock travel W-axis: 420 mm Workpiece data Workpiece diameter with manual loading: max. 200 mm Workpiece diameter with automatic loading: max. 150 mm Max. workpiece length: 400 mm Milling parameters Cutter diameter: 40 - 102 mm Maximum cutter length: 230 mm Milling arbor diameter (standard): 16 - 32 mm Milling coordinates Z-axis: 100 - 400 mm X-axis: 100 - 150 mm Y-axis (milling spindle end face): 50 - 230 mm W-axis (tailstock end face): 165 - 585 mm Speeds Cutter speed B-axis: 0 – 1,500 rpm Workpiece speed C-axis: 0 – 350 rpm Feed rates X-axis: 3,500 mm/min Z-axis: 3,500 mm/min Y-axis: 4,000 mm/min W-axis: 5,500 mm/min V-axis (gantry loader): 80,000 mm/min Swivel range Shift milling head A-axis left/right: 50° / 60° MACHINE DETAILS Weight: 6 t EQUIPMENT - CNC control IBH - Loading device Djljwcrnxoikd Ncscg - Various accessories

Condition: ready for operation (used), Functionality: fully functional, machine/vehicle number: P5276678, ram adjustment: 70 mm, stroke adjustment: 100 mm, pressing force: 35 t, Machine from the insolvency of an automotive supplier - machines are currently still in operation! TECHNICAL DETAILS Nominal force: 35 t Stroke adjustment: 8 - 100 mm Ram adjustment: 70 mm Stroke rate: 130 / min Motor power: 3 HP Other auctions from the same location: Further information according to the manufacturer - no guarantees given Ram surface: approx. 350 x 180 mm Space required: approx. 1.0 x 1.6 x 2.3 m Dcslikd Nswhdh Iscjg

Condition: used, machine/vehicle number: 007924, Position 1: Panel Feeding and Loading BARBERAN-RFU-4-C-1700 Dcelikdewfxklj Ncog Position 2: Brushing Machines BARBERAN-RFU-4-C-1700 Position 3: Calender BARBERAN-RFU-4-C-1700 Position 4: Gluing Machine BARBERAN-RFU-4-C-1700 Position 5: Continuous Cycle Presses BARBERAN-RFU-4-C-1700 Position 6: Panel Stacking and Offloading BARBERAN-RFU-4-C-1700

Condition: new, Year of construction: 2022, Base sheet fiber laser metal cutting machine with full protection Maximum cutting area reaches up to 12000mm*2500mm, suitable for a variety of cutting options. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Cutting performance and efficiency are improved by maintaining gas flow steady with little turbulence. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. The cutting process works even at the edge of thin sheets, and ensures no chatter marks. With One-click Processing, one laser cutter is able to process multiple sheets in batches with a one-off setup, achieving batch processing. Condition: New Laser Type: Fiber Laser Laser Power: 1000W - 40000W Cutting Area: 3048*1524mm - 12500*2600mm Cutting Speed: 0-110m/min Dolikjhwhfqsd Ncjcg Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: used, Year of construction: 2021, fuel type: diesel, General information Field of application: Construction Serial number: M200044791 Weights Empty weight: 4.050 kg Functional Lifting capacity: 453 kg Working height: 1.200 cm Other information Front tyres / undercarriage remaining: 100 Rear tyres remaining : 100 Tyre brand: Outrigger Transport dimensions (LxWxH): 3.53x1.76x2.46 Additional information Dcslijt Afvtokd Ncsg Please contact Pfeifer Rentals & Sales B.V. for more information

Condition: used, Year of construction: 2007, operating hours: 2,547 h, fuel type: diesel, General information Field of application: Construction Serial number: CD113585 Weights Empty weight: 6.340 kg Dcslikd Nsv U I Efscjg Functional Lifting capacity: 500 kg Working height: 1.500 cm Other information Front tyres / undercarriage remaining: 40 Rear tyres remaining : 40 Tyre brand: Wide Wall Transport dimensions (LxWxH): 5.3x2.25x1.91 Additional information Please contact Pfeifer Rentals & Sales B.V. for more information

Condition: used, Year of construction: 2021, fuel type: diesel, General information Field of application: Construction Serial number: M200045426 Weights Empty weight: 3.390 kg Dcjliketr Tapsd Ncjg Functional Lifting capacity: 454 kg Working height: 1.200 cm Other information Front tyres / undercarriage remaining: 100 Rear tyres remaining : 100 Tyre brand: Outrigger Transport dimensions (LxWxH): 3.53x1.76x2.62 Additional information Please contact Pfeifer Rentals & Sales B.V. for more information

Condition: used, Year of construction: 2021, fuel type: diesel, General information Field of application: Construction Serial number: M200044737 Weights Empty weight: 3.750 kg Functional Lifting capacity: 680 kg Working height: 1.000 cm Other information Dcelikd Nstua Imscsg Front tyres / undercarriage remaining: 100 Rear tyres remaining : 100 Tyre brand: - Transport dimensions (LxWxH): 3.53x1.76x2.46 Additional information Please contact Pfeifer Rentals & Sales B.V. for more information