BayWa AG

Year of construction: 1999, condition: used, Max. drilling diameter in steel, strength 600MPa: 50mm, max. drilling diameter in cast iron, strength 250MPa: 60mm, max. boring diameter (with guide) in steel, 600MPa: 200mm, max. thread in steel, 600MPa: M50x1.5, max. thread in cast iron, 250MPa: M60x2, spindle reach: 320-1250mm, pitch circle of holes: 1208-3039mm, distance from spindle axis to base plate: 320-1380mm, max. arm height adjustment: 750mm, max. drill carriage travel on arm: 930mm, arm swivel range: +/-180°, spindle head diameter: 75h6, spindle diameter at front bearing: 55mm, length: 2900mm, width: 1120mm, height: 3271mm, weight: 4.2t, with documentation. An on-site inspection is possible. Hodszuzziepfx Ah Eenr

Condition: used, Cutting speeds: 30/60/130/260m/min, mains connection: 380V/50Hz three-phase, rated supply current: approx. 7.5A, upstream fuse: 20A slow-blow. An on-site inspection is possible. Hnsdpszuz Amofx Ah Esr

Year of construction: 2003, condition: used, Max. grinding length: 2000mm, max. grinding width: 1000mm, max. working height with new grinding wheel: 600mm, max. workpiece weight: 3.2t, max. table load: 4.5t, clamping surface dimensions: 2860x1000mm, tool mounting: 4x grinding wheel mounts, spindle diameter at front bearing: 90mm, grinding wheel diameter: 500mm, max. grinding wheel width: 150mm, mounting diameter: 203.2mm, spindle speed: 1000-3000/min, cross travel: electromechanical, cross travel feed: 1-5000mm/min, max. cross travel: 1100mm, smallest programmable value cross axis: 0.001, vertical travel: electromechanical, vertical travel feed: 1-5000mm/min, max. vertical travel: 650mm, smallest programmable value vertical axis: 0.001, feed drive type: hydraulic, connected load: 125kVA, length: 10,284mm, width: 5137mm, height: 3925mm, weight: 22t, operating hours: 18,176h, with documentation. An on-site inspection is possible. Hjdpfxjzuzyxj Ah Esnr

Year of construction: 1987, condition: used, One Rösler R 300 A/SA-KP and one R 300 RT are available, year of manufacture: 1986/ 1987, 1) R 300 A/SA-KP, connected load: 4.5kW, weight: 830kg, 2) R 300 RT, connected load: 19kW, weight: 2,130kg, with documentation. An on-site inspection is possible. Hnedpfxszuzy Eo Ah Eor

Condition: used, Year of construction: 1988, A Heckert horizontal CNC machining center in need of repair is offered. Travel X/Y/Z: 800mm/560mm/805mm, tool taper: SK50, pallet size: 500mm/500mm, number of pallets: 2, max. pallet load: 800kg, tool magazine: 40, max. spindle speed: 4200rpm, control: Siemens Sinumerik, rapid traverse X/Y/Z: 24m/min, B-axis: 360°. Machine dimensions: approx. 6510mm/5115mm/2933mm, weight: approx. 16000kg. The machine could not be powered up again after a power outage. Inspection possible by arrangement. Hnodpfx Aezuzy Seh Eer

Condition: used, Year of construction: 1999, Two Juki button sewing machines and one Herbert Meyer fusing machine are available. 1) 2x Juki MB-373 button sewing machines, stitch type: single-thread chainstitch, max. sewing speed: 1500stitches/min, number of stitches: 8/16/32, crosswise feed: 2.5mm-6.5mm, lengthwise feed: 0mm/2.5mm-6.5mm, button size range: 10mm-28mm, needle bar stroke: 48.6mm. 2) Herbert Meyer RPS-L 600 fusing machine, year of manufacture: 1999, fusing width: 600mm, max. belt speed range: 9m/min, max. pressing pressure: 3.5bar. Oil level and needles should be checked. On-site inspection is possible. Hodpfxjzuzzcs Ah Esnr

Condition: used, An MBK horizontal cage welding machine for the production of small square reinforcement cages is offered. Cage diameter: approx. 200mm-1500mm, max. cage length: 4000mm, wire diameter: 5mm-12mm, welding capacity: approx. 100kVA, control: Zoller+Fröhlich. Machine dimensions: approx. 6000mm/2500mm/2200mm, weight: approx. 8500kg. Inspection possible by arrangement. Hnedpfx Ahszuzzpj Esr

Year of construction: 2006, condition: used, Control voltage: 24V DC, rated current: 85A, connected load: 39kVA, rated power: 49kW, control-on operating hours: 32,779h, automatic operation 1: 5,040h, automatic operation 2 operating hours: 1,844h, production time: 33,731h, length: 3231mm, width: 2076mm, height: 1917mm, weight: 4.8t, with documentation, chip conveyor and FMB turbo 8-80 bar feeder. An on-site inspection is possible. Hodpfszuzzvsx Ah Eonr

Year of construction: 2003, condition: used, Rated current: 60A, control voltage: 24V, connected load: 33kW, length: 2290mm, width: 1350mm, height: 1630mm, weight: 4.65t, operating hours: 78,439h, with documentation, chip conveyor and bar feeder. An on-site inspection is possible. Hnsdpfx Aozuzz Ash Eor

Year of construction: 2007, condition: used, An ARISTO flatbed cutting and routing system with MultiHead IV, HF Routing Device, color camera and ARISTOprojection is offered. Cutting width: 2300mm, static repeatability: +/-0.08mm, max. material clearance thickness: 55mm, drive system: digital AC servo motors, data format: HPGL compatible, interface: RS232C/V.24, transmission speed: 38400baud, vacuum system: adjustable matrix vacuum zones. 2) MultiHead IV type 4021/OT.M.P. IV-1, electrically oscillating tool axis, max. pressure: 180N at 6bar, integrated laser pointer, color camera with AutomaticEye registration system, tool head dimensions W/H/D: 166mm/390mm/330mm, weight: approx. 8.5kg. 3) HF Routing Device for spindles 4040 DC/4040 DC-S, max. speed: 50000rpm/60000rpm, power: max. 800W/1000W, Z-axis stroke: 50mm, collet range: 1.5mm-6.35mm. 4) ARISTOprojection for 1:1 projection of the contours onto the working area. Machine was regularly maintained. Documentation available. Inspection possible by arrangement. Hnjdpjzuzz Nsfx Ah Esr

Condition: used, Year of construction: 2006, X-axis: 1600mm, y-axis: 1800mm, z-axis: 1000mm, max. workpiece weight: 3.5t, noise level: less than 70dBA, compressed air connection: 6-8bar, connected load: 2500VA, control: CALYPSO 7.6.08 software, length: 2940mm, width: 2450mm, height: 3800mm, weight: 8.5t, operating hours: 38,996h, with documentation. An on-site inspection is possible. Hedpezuz Aajfx Ah Eenr

Condition: used, Year of construction: 1998, A Klöckner DESMA rubber injection molding machine with increased clamping pressure is offered. Material processing: rubber, clamping force: 4500kN, min./max. mold height: 180mm/530mm, adjustable opening stroke: 570mm, clear distance between tie bars X/Y: 600mm/810mm, max. clamping area X/Y: 670mm/940mm, heating platen size X/Y: 670mm/940mm, injection: from above, max. injection volume: 3300cm³, injection force: 1886kN, max. injection pressure: 2150bar, screw diameter: 55mm, injection plunger diameter: 105mm, operating pressure: 250bar, number of control zones: 12, heating capacity per control zone: 21kW, ejector: hydraulic top and bottom, ejector slot spacing: 730mm. The machine is currently not operational because the control cabinet of the DRC 2000 (Simatic S7) is already being used elsewhere and is not part of the machine. Documentation available. Inspection possible by arrangement. Hedpfx Aozuz Agjh Esnr

Condition: reconditioned (used), Year of construction: 2006, year of last overhaul: 2026, Studer S30-1 CE High-precision cylindrical grinding machine for external and internal grinding. Hsdpfx Ahozuzylj Eenr - Distance between centers: 650 mm - Height between centers: 175 mm - Currently undergoing a rebuild (retrofit) process to offer performance and precision comparable to that of a new machine. - Equipped with a digital measuring system. - Equipped with refurbished components and adjusted to ensure maximum reliability and precision. - Wide range of accessories available. - A working demonstration and test can be performed at any time. - Delivery time: upon request (in the final stages of the rebuild) - The photographs show a reference machine of the same model, refurbished by us. Project reference: OP26-006

Condition: used, Year of construction: 2003, Year: 2003 Condition: very good Configuration: - Number of knives: 4 - Extended side air tables: 750 × 750 mm Hnedpjzuzx Ujfx Ah Esr

Condition: refurbished (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: 30-009, warranty duration: 6 months, total width: 660 mm, total length: 2,215 mm, total height: 1,620 mm, type of input current: three-phase, overall weight: 360 kg, year of last overhaul: 2025, GULLIVER IRIS 20 Dough Divider The Iris dough divider is designed for dividing both soft and hard dough. This machine is suitable for any bakery, providing precise and consistent portioning. The machine is equipped with an interchangeable blade system (from 1 to 6), allowing the weight and shape of the portions to be adjusted to suit specific products. The control panel with a computer allows for the operation of up to 30 programs. Portion weight range (depending on the number of blades): from 30 g to 1200 g Hsdpfxszuzx Is Ah Ejnr Standard equipment: 1–3 stainless steel cutting blades flour dispenser restart system Optional equipment: 4–6 cutting blades, special blades

Condition: used, mileage: 274,885 km, power: 95 kW (129.16 HP), fuel type: diesel, gearing type: mechanical, first registration: 11/2010, emission class: euro5, color: other, number of seats: 23, Year of construction: 2010, Equipment: ABS, Height: 280 cm Hnjdpfjzuzxzex Ah Esr Damage: None = Company Information = We are an international company based in Belgium, in the vicinity of Brussels (+/- 20 km). Belgian Bus Sales is your ideal partner for the buying and selling of used buses and has a large parking area that serves as an exhibition space. We always have a large number of buses of all makes, capacities, and models in stock, covering every price range. We can find the right tourist, school, or city bus for you, tailored to your needs or budget. All information is subject to change without notice. Errors, prior sales, and typographical errors excepted. Opening hours for viewing used buses: Mon-Fri: 08:30 - 12:00, 12:30 - 17:00. (Mowimy po Polsku Agata) We speak your language: Dutch, French, English, Spanish, Portuguese, Italian, Russian, Polish, and more.

Condition: good (used), mileage: 593,304 km, power: 274 kW (372.54 HP), first registration: 09/1992, fuel type: diesel, tire condition: 50 %, axle configuration: 6x4, fuel: diesel, color: other, driver cabin: day cab, gearing type: mechanical, emission class: euro2, suspension: steel, total length: 8,000 mm, total width: 2,500 mm, total height: 3,400 mm, Year of construction: 1992, Equipment: ABS, electric window regulation, = Additional options and accessories = - 1 fuel tank - Armrest - Central lubrication Hjdpezuzxusfx Ah Eonr - Day Cabin - Drum brakes - Front suspension: Leaf - Hub Reduction - PTO - Rear suspension: Leaf - Thick Axles = More information = Cab: single Tyre profile: 50% Brakes: drum brakes Suspension: leaf suspension Front axle: Steering Technical condition: good Visual appearance: good

Condition: used, Year of construction: 2007, Heating plate press Manufacturer: OTT Type: Solid 16-32 Year of manufacture: 2007 Technical data Hedozuzxnopfx Ah Ejnr Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, Continuous press Manufacturer: Ligmatech Type: Optimat MDE 10 Year of manufacture: 2001 Technical data Body dimensions - Length: 300 - 2500 mm - Height: 300 - 1300 mm - Depth: 120 - 600/800 mm - Pressing forces are generated electrically, both horizontally and vertically, and can be varied independently - Pressing forces are applied vertically via a pressure plate and horizontally via 3 pressure jaws each - Pressing takes place centered and on a zero line on the operator side Positioning of the pressure jaws: - Top pressure jaw with forced guidance on the top press, optionally lowerable via cylinder - Middle pressure jaw freely programmable and motor-driven - Bottom pressure jaw freely programmable and movable via a common drive with the middle pressure jaw Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding. Hnedpszuzxbofx Ah Eor

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. Hnjdpszuzw Dofx Ah Esr CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Manufacturer: OTT Type: 300-K-D0 Year of manufacture: 1996 Hodszuzwwspfx Ah Eonr Technical data Plate dimensions: 2550 x 1350 mm Hot water heating 6 pressure cylinders Total pressing force: 135 t Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2007, Lamination press Manufacturer: Dimter Type: PROFIPRESS L2500 Year of manufacture: 2007 Technical data Wood dimensions to be processed Wood width, panels: 30 - 150 mm Wood thickness: 11 - 60 mm Wood inlet length: 800 - 2500 mm Panel widths, variable: max. 1300 mm Specific pressing pressure for cross-sections of 2500 x 60 mm: up to 1.6 N/mm2 The pressing surface per press cycle must not be smaller than 100 cm2 Filling width of the press per cycle: min. 650 mm / max. 1300 mm Max. filling area of the press per cycle: 3.25 m2 (The max. usable press width depends on the widths of the individual lamellas.) Wood type Softwood/hardwood Press without options Electrical connection, press: 7 kW Electrical connection, 40 kW generator: 56 kW Operating voltage: approx. 400 Volt / 50 Hz (C/s) Collection table extended to 3700 x 1300 mm, with stainless steel wood support Motor-driven multi-function slider Lamination press Profipress L 2500 Press bed area approx. 2500 x 1300 mm Sturdy base frame with lower press table made of stainless steel as a grounding electrode Quick-change stop guide sets for panel thicknesses of 19 - 40 mm, which can be hydraulically adjusted to the current filling width Hydraulic special pressure elements ensure uniform pressure distribution over the entire joint length and compensate for tolerances In multi-lane operation, filling widths may vary by a maximum of 15 mm Upper pressure plate with hydraulic drive generates high vertical pressing pressure for minimal displacement Integrated hydraulic unit for generating pressing force and driving the hydraulic motors Control cabinet and control panel Protective cladding Additional individual pressure elements from above Automatic gluing station with precision gluing head Infeed for different widths Camera Washing and rinsing device for gluing head Modem incl. software for online connection Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is non-binding. Hsdpfx Ahezuzwqj Eenr

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 Hsdpfxjzuzwke Ah Esnr The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm - Min. filling height 900 mm - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm - Max. power 13.2 kW - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: ready for operation (used), Year of construction: 2022, operating hours: 2,044 h, controller manufacturer: SIEMENS, controller model: SINUMERIK 840D sl, laser power: 6,000 W, travel distance X-axis: 3,500 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 115 mm, number of axes: 3, This 3-axis TRUMPF TruLaser 5030 fiber L76 FMC was manufactured in 2022. It features a working format of 3,000 x 1,500 mm and a powerful 6000W solid-state disk laser. The machine includes an automatic longitudinal pallet changer and advanced cutting capabilities, such as adaptive lens systems and automatic nozzle changers. If you are looking to get high-quality fiber laser cutting capabilities, consider the TRUMPF TruLaser 5030 fiber L76 FMC machine we have for sale. Contact us for further details. • Working format/area: 3,000 x 1,500 mm; X 0–3,000 mm / Y 0–1,500 mm / Z 0–115 mm • Machine design: Closed machine frame; gantry drive with direct linear drives; automatic longitudinal pallet changer; integrated control cabinets and storage cabinet; working-area lighting; machine status light; water/air machine and laser chiller; CE compliant; ambient temp 5–35 °C • Dynamics/accuracy: Max simultaneous axis speed 280 m/min; Ps 0.03 mm; Pa 0.05 mm; min programmable increment 0.001 mm • CNC control: Siemens SINUMERIK 840D sl with 21.5" color MultiTouch; MultiTouch HMI; USB and RJ45; integrated technology data; programmable cutting gas/pressure; production planning; multi-sheet processing; automatic shutdown; Remote Support interface; Condition Guide; Cutting Guide; Central Link; Online Update Manager • Laser source: TRUMPF TruDisk 6001 (6 kW) solid-state disk laser; fiber-optic beam delivery; one LLK output; closed beam guidance; high back-reflection resistance; stable output over service life • Cutting head: Universal cutting unit; single cutting-head strategy; adaptive lens system; protective glass with online condition monitoring; auto nozzle centering; collision protection; capacitive height control; automatic focal position; pilot laser • Standard cutting functions: AdjustLine; BrightLine fiber; ControlLine; FastLine; FlyLine; FocusLine; NitroLine; PierceLine; Performance package; Highspeed cutting package; Copper and Brass cutting packages; Micro-weld • Additional cutting package: Highspeed Eco (fusion cutting, medium-thickness stainless steel) with up to 70% cutting-gas reduction and up to 100% sheet throughput increase • Automatic nozzle changer: 21 positions; automatic change/cleaning/re-setting tied to material/process; reduces setup/handling • Drop&Cut: Integrated camera; assigns live image of residual sheet to part geometry; live cutting preview; no separate programming needed for basic use • Process monitoring camera: Front-area monitoring (~2.5 m); remote observation; preliminary result assessment; video stream output to external monitor • Pallet/material handling (machine-integrated): Automatic longitudinal pallet changer; loading/unloading parallel to machining; pallet access from three sides Additional equipment • LiftMaster Compact 1530 (AL34) automatic loading/unloading system • Type 1530; max sheet 3,000 x 1,500 mm; min sheet 1,000 x 1,000 mm • Max sheet thickness 25 mm; max sheet weight 900 kg; max unloading weight 900 kg • With rake lifter: max thickness 25 mm; with rake lifter + belt system: max thickness 15 mm Hodpfjzuzwdox Ah Eenr • Minimum part size with rake lifter: 150 x 150 mm • LiftMaster equipment/options • Storage connection; extended pallet travel out of machine • Sheet separation device; double-sheet detection; synchronous loading • Thin-sheet separation (0.8–2.0 mm); loading station for 90 mm stack height • Structural-steel loading grippers, 67 mm pitch, replaceable tines

Condition: used, Year of construction: 1998, Continuous body press Manufacturer: LIGMATECH TYPE: MPP 15 Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Working height: 500 mm Transport speed: min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Hsdpezuzv Tefx Ah Esnr Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.