Lasergraaf bv

Condition: excellent (used), Year of construction: 2017, TruBend 5130, including Toolmaster, manufactured in 2017. 130 tons, 3 meters. Isdey Tmnhjpfx Ahqotg

Condition: repair required (used), functionality: limited functionality, Year of construction: 2014, TRUMPF TruLaser 5030 fiber Year of manufacture: 2014 5,000 Watt TruDisk 5001 Siemens 840D SL Special price due to site closure / insolvency For sale is a used TRUMPF TruLaser 5030 fiber from 2014. According to the previous owner, the machine was in continuous productive use until 2025 and operated without any known problems. Subsequently, as part of an insolvency, the system was shut down for approximately one year and no longer operated. Currently, the machine is not connected and therefore cannot be demonstrated. The main power cables were roughly cut by an electrician during disconnection (typical in such a case). However, these cables can be reordered or replaced professionally. Ideal machine for a buyer who wants to refurbish, clean, connect, and put the system back into operation themselves. For this purpose, the machine is available at an exceptionally attractive special price. Extremely affordable. Technical data Manufacturer: TRUMPF Model: TruLaser 5030 fiber Year of manufacture: 2014 Machine type: Laser cutting system Laser source: TRUMPF TruDisk 5001 solid-state laser Laser power: 5,000 W Control: Siemens 840D SL Working area / max. sheet size: 3,050 x 1,550 mm Travel distance X-axis: 3,000 mm Travel distance Y-axis: 1,500 mm Travel distance Z-axis: 116 mm Rapid traverse: 280 m/min Max. workpiece weight: 900 kg Max. sheet thickness: 10 - 25 mm according to documentation Operating voltage: 400 V / 50 Hz Machine weight: approx. 12,000 kg Dimensions L x W x H: approx. 9,500 x 6,300 x 2,500 mm Color: gray / blue Cabin: Protective cabin Equipment TRUMPF TruDisk 5001 solid-state laser Laser cooling unit Cooling unit for the system Universal cutting unit Multi-chamber extraction system Light barriers Electric roll-up roof Hydraulically adjustable pallet changer Protective cabin Notes on condition Machine currently not connected Test run currently not possible Operating hours could not be read out Machine stood for approx. one year due to insolvency Connection cables to the main power supply are cut and must be replaced Machine, cooler and extraction system should be cleaned and technically inspected Filters / maintenance should be renewed or carried out before re-commissioning Machine documentation is not completely available according to the expert opinion Positive points to mention Last service according to documentation in 2021 Cutting unit was renewed in 04/2021 Machine was in operation until 2025 Very interesting basis for in-house refurbishment A fantastic special price is possible Sale Itjdpfx Ahsy Tmcxoqog Location: Germany Availability: immediate Price: on request / special price Condition: used, currently not demonstrable Sale from location, as inspected Errors, prior sale and technical changes reserved.

Condition: excellent (used), functionality: fully functional, Year of construction: 2023, operating hours: 10,691 h, control type: CNC control, laser type: fiber laser, laser hours: 10,691 h, power: 10 kW (13.60 HP), overall weight: 19,000 kg, total length: 19,900 mm, total width: 4,100 mm, total height: 2,730 mm, Equipment: dust extraction, 2023 Model Prima Power Laser Genius+ 2060 Machine Dimensions: 19,900 x 4,100 x 2,730 mm Machine Weight: 19,000 kg Total Operating Hours: 10,691 hours Regularly serviced and kept in clean working condition Technical Specifications 2000 x 6000 mm Dual Table System 10 kW Fiber Laser Working Area: 2200 mm x 6220 mm Iodpoy Taakofx Ahqstg IPG Resonator Donaldson Dust Collection Unit Linear Motor System on X and Y Axes Our machine is currently in active operation. You are welcome to visit our facility and inspect the machine in person. Transportation and shipping costs are the responsibility of the buyer.

Condition: good (used), functionality: fully functional, Year of construction: 2013, operating hours: 9,100 h, control type: CNC control, laser power: 4,000 W, sheet thickness (max.): 25 mm, sheet thickness steel (max.): 25 mm, sheet thickness stainless steel (max.): 20 mm, sheet thickness aluminum (max.): 15 mm, sheet thickness brass (max.): 6 mm, sheet thickness copper (max.): 6 mm, pipe diameter (max.): 310 mm, pipe length (max.): 3,000 mm, table length: 3,000 mm, table width: 1,500 mm, working length: 3,000 mm, working width: 1,500 mm, cutting speed: 5,000 mm/min, Equipment: cooling unit, dust extraction, emergency stop, nozzle changer, safety light barrier, TRUMPF TruLaser 3030 fiber (L49) (A1) 11/2013 4 kW 3. Technical Specifications Working area: 3000 × 1500 mm Operating hours (04/2026): Beam ON: 9,100 h Machine ON: 31,000 h 4. Maintenance & Condition - Maintained annually by TRUMPF - New IPC installed in 01/2026 (cost: 12K EUR; old IPC with broken network port can be used as a backup) 5. Standard Machine Configuration Working Area & Machine Design Working area: 3000 × 1500 mm Fully enclosed machine frame Enclosed beam guidance via light cable (LLK) Integrated cabinet with roller shutter Sliding roof Working area illumination Integrated electrical cabinets with interior lighting Drive & Motion System Torque drive combined with linear direct drives Automatic pallet changer in longitudinal direction Longitudinal conveyor belt Process Support Cooling unit Positioning laser diode Spray device Automatic nozzle cleaning Transport and installation equipment Cutting Technologies PierceLine FocusLine NitroLine PlasmaLine Microweld 6. Laser Standard Laser Configuration Integrated solid-state laser with 1 LLK output Pump diode excitation Laser power control Extended Laser Configuration TruDisk 4001 solid-state laser with 1 LLK output Upgrade capability for max. 1 additional LLK output on the TruDisk 7. Cutting Unit Standard Configuration Universal cutting unit Single cutting head strategy Protective glass against lens contamination Protective glass condition monitoring ControlLine: height control and sheet edge detection Extended Configuration Nozzle changer DetectLine: precise sheet position detection Copper cutting package (including cutting data for N2, O2) Brass cutting package (including cutting data for N2) 8. Control System & Software Operation & Programming TruTops Laser via network access (customer-provided PC required) Easy workshop programming Fast reproduction of jobs Integrated technology database Automatic shutdown function Programmable cutting gas / pressure selection Control System Sinumerik 840D SL control system 17" touch color display Software & Process Functions ContourLine Microweld Itsdpfx Aey S U N Rehqsg FastLine FlyLine AdjustLine Remote teleservice via internet 9. Data Transfer & Interfaces Standard Interfaces USB interface RJ-45 network connection Extended Interfaces MDE interface 10. Safety & Environmental Systems Safety Features CE certification Light barriers Machine enclosure with certified viewing window (right-side door) Extraction & Dust Protection Multi-chamber extraction system Compact dust extraction unit Dust protection for equipment sheet metal 11. Material Handling & Automation Conveyor & Handling Systems Wide cross conveyor with tilting container Container positioned on the left side of the machine Automation Options LiftMaster retrofit 12. Tube Cutting Device / RotoLas Tube Processing Equipment Tube cutting device incl. 4 internal and external jaws (including electric roller roof, left-side sliding inspection door for enhanced visibility, and accessory trolley; integrated cabinet with roller shutter omitted) Components Automatic chuck External support for tubes up to 3 m (incl. 1 stepped roller) Base jaws for additional clamping sets Prism clamping set First base carrier with shifting device (longitudinal pallet changer) Additional base carriers 2 × workpiece carriers D 15–310 mm Clamping claws (2 pcs.) 13. Warranty / Sales Notice No warranty Purchased as is.

Condition: excellent (used), functionality: fully functional, Year of construction: 2008, Trumpf TruPunch 2020 Iodpfxoy S Adps Ahqjtg

Condition: used, Tube ends – forming machine BLM (Italy) used tube end forming machine BLM Itjdpfxey St Ile Ahqsg for tubes with six-position turret Drive power: 7.5 kW max. tube diameter approx.: 40 mm Max. forming length estimated: 80 mm Weight approx.: 1.5 t

Condition: new, functionality: fully functional, Year of construction: 2026, laser type: fiber laser, laser source manufacturer: Maxphotonics, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, emergency stop, fume extraction, safety light barrier, Why keep struggling with the cut quality of fine plasma systems? Itjdjy Smf Repfx Ahqsg Why waste valuable space in your workshop with a shuttle table? Why continue spending thousands of euros every year on expensive plasma consumables? Beyond the obvious advantages of modern fiber laser technology—particularly in terms of precision and almost burr-free laser cut quality—laser cutting is also incredibly economical. At the same time, operating a laser cutting machine is significantly easier compared to conventional plasma cutting systems. Best of all: At Schmidt & Partners Cutting, we provide comprehensive support for your system throughout its entire service life—from our two service locations. As a reliable partner in the cutting industry, we offer first-class advice, installation, training, maintenance, and repairs. Additionally, our experience and expertise is at your disposal for assistance with cutting parameters for special materials. We also gladly support you in planning and implementing the required occupational safety measures relating to laser technology within your company. PENTA LASER MINI BULL Cutting area: 1,500 x 3,000 mm Laser systems available from 2 kW to 60 kW CE-certified, with risk assessment Don't have a suitable filtration system yet? We will also design a custom filtration solution tailored to your requirements. We look forward to hearing from you!

Condition: used, Year of construction: 2020, operating hours: 31,623 h, laser power: 4,000 W, working length: 3,000 mm, working width: 1,500 mm, year of last overhaul: 2026, Machine Configuration: Standard Equipment: Machine - Working area: 3000 × 1500 mm - Enclosed machine frame - Longitudinal conveyor belt - Motion unit for high-precision processing - Gantry drive in combination with linear direct drives - Cooling unit for machine and laser (water-air) - Work area lighting - Positioning laser diode - Spray device - Automatic nozzle cleaning - Integrated control cabinets - Integrated cabinet - Enclosed beam guidance via laser light cable (LLK) - Machine status light - Ambient operating temperature 5 to 40 °C - Transport and assembly device TRUMPF Laser - Excitation via pump diodes - Laser power control Cutting unit - Single-head cutting strategy - Universal cutting unit with adaptive lens system - Protective glass - Online condition monitoring of protective glass Control - Fast reproduction - SINUMERIK 840D SL control - Ergonomic control panel with 21.5″ wide-screen multi-touch color display - Integrated technology data - Auto shut-off - Programmable selection of cutting gas/pressure - Microweld - Remote support interface - Production planning - Multi-sheet processing - Condition Guide - Cutting Guide Functions - AdjustLine Itjdpfx Asy Sivfohqeg - ControlLine - FastLine - FlyLine - FocusLine - NitroLine - PierceLine - Copper cutting package - Brass cutting package Data transmission - USB interface - RJ-45 network interface - Central Link - Online Update Manager Safety - CE marking - Light barriers - Multi-chamber extraction system - Machine paneling with certified viewing window, right door Extended Standard Equipment - Compact dust extractor - Support slats made of construction steel - Network installation via remote support Extended Machine Equipment Extended Laser Equipment - External solid-state laser TruDisk 4001 with 1 LLK output Additional Machine Functions - Drop&Cut - Integrated camera 1 for process monitoring Additional Cutting Packages - Highspeed Eco cutting package Extended Machine Equipment - Dust protection for device panel Data transmission - Wireless Operation Point Availability: approx. 6–8 weeks after receipt of order, at the earliest end of June 2026 Price: on request Current location: TRUMPF Reconditioning Facility Netherlands The machine is currently undergoing reconditioning!

Condition: used, functionality: fully functional, Year of construction: 2018, machine/vehicle number: 0751801060702, For sale: BLM GROUP BLM LT FIBER tube and profile laser cutting machine with Active Scanner, equipped with an IPG Photonics YLS-2000-CUT 2000 W laser source. The machine is fully operational, both technically and in production, and is in continuous use at a manufacturing facility (current laser beam operating time: 6,950 hours). The machine features an integrated automatic material loading and unloading system, significantly increasing production efficiency and operator convenience. Technical data: • Model: LT FIBER • Laser type: Fiber • Laser source: IPG YLS-2000-CUT • Laser power: 2 kW • Laser source year: 2018 • Power supply: 380 V / 3-phase / 50 Hz • Installed power: 26 kVA • Machine weight: approx. 9,000 kg Machine advantages: • Fully production-ready • Equipped with ACTIVE SCAN and a seam position detection camera • Integrated loading and unloading system • Possibility to perform tests during operation • High cutting quality and precision • Regularly used Isdjy Sf Eispfx Ahqetg • Ready for further operation Additional photos and videos of the machine in operation can be provided, as well as the possibility to inspect the machine under power on site. Price upon request

Condition: good (used), functionality: fully functional, Year of construction: 2014, Sheet width: 3000 mm Sheet length: 1500 mm Itjdjy Sak Topfx Ahqeg Sheet thickness: 8 mm Workpiece weight: 200 kg Maximum punching force: 220 kN Total power requirement: 9.5 kW Approx. dimensions: 7395 x 6540 x 2072 mm Equipment: - Sheetmaster - Operating hours: 65,000 h

Condition: used, functionality: fully functional, Year of construction: 2007, control type: CNC control, For sale: CO₂ Tube Laser BLM Group Adige LT712D The machine is fully operational and in daily use in production. Inspection and testing on site are possible. The laser source ROFIN RF tube DC025 has been replaced with a new one. The new source has only 2386 operating hours. Specifications: Model: BLM Adige LT712D CO₂ tube laser Year of manufacture: 2007 Laser source: Rofin RF tube DC025 New laser source operating hours: 2386 h Total machine operating hours: 89186 h Automatic tube loading and unloading CNC control Autofocus cutting head Suitable for cutting round, square, and rectangular profiles Iodpfx Ahoy R Tt Seqjtg Automatic profile centering and measurement devices Professional industrial construction Scope of supply: Rofin DC-K laser integration AK-HP 591-LT712 cutting head 5” focusing system 6500 mm tube system Automatic unloading module The machine is suitable for the production of metal constructions, furniture, automotive, tubular structures, and other metal products. If you have any further questions, we will be happy to answer them.

Condition: new, functionality: fully functional, Year of construction: 2026, control type: PLC-controlled, degree of automation: semi-automatic, actuation type: electric, controller manufacturer: Siemens, laser source manufacturer: Max Photonics, laser source model: Max Photonics 6kW mit CE, laser power: 6,000 W, sheet thickness (max.): 10 mm, sheet thickness steel (max.): 10 mm, sheet thickness stainless steel (max.): 8 mm, sheet thickness aluminum (max.): 6 mm, sheet thickness brass (max.): 6 mm, sheet thickness copper (max.): 6 mm, pipe diameter (max.): 240 mm, pipe length (max.): 6,050 mm, working length: 8,050 mm, working width: 250 mm, working height: 250 mm, travel distance X-axis: 400 mm, travel distance Y-axis: 6,500 mm, travel distance Z-axis: 280 mm, feed rate X-axis: 116 m/min, feed rate Y-axis: 131 m/min, feed rate Z-axis: 30 m/min, positioning accuracy: 0.03 mm, repeat accuracy: 0.05 mm, workpiece weight (max.): 100 kg, power: 6,000 kW (8,157.72 HP), input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, compressed air connection: 8 bar, overall weight: 5,000 kg, total length: 12,500 mm, total width: 2,400 mm, total height: 2,550 mm, warranty duration: 12 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, With a fully redesigned machine concept, it unites maximum stability, highest efficiency, precise processing, and intelligent automation in one system. This makes it optimally suited for processing a wide variety of metal tubes and profiles – flexible, reliable, and powerful. A patented, innovative design combined with an exclusive automatic loading and unloading system significantly boosts productivity. The system operates faster, more stably, and more intelligently, and is available in different configurations to suit your individual requirements. Thanks to enhanced dynamics and increased performance, the machine delivers outstanding results across all processing operations – whether cutting, drilling, or complex contour cutting. The cutting quality is of the highest standard: smooth surfaces, minimal thermal impact, and virtually no residue or rework required. Isdpfxjy R I R Eo Ahqjtg Numerous patented core technologies ensure consistently high processing accuracy and perfect results – even in demanding continuous operation. Even after many years of intensive use, the system’s performance remains at an exceptionally high level. This makes your investment a sustainable, future-proof solution for your production. Cutting power: 6000W Laser source: MAX Photonics Laser head: BOCI Autofocus Max. tube length: 6500mm Tube diameter: 240mm Acceleration: 1.2G

Condition: new, functionality: fully functional, Year of construction: 2026, control type: PLC-controlled, degree of automation: semi-automatic, actuation type: electric, controller manufacturer: Siemens, laser source manufacturer: Max Photonics, laser source model: Max Photonics 3kW mit CE, laser power: 3,000 W, sheet thickness (max.): 8 mm, sheet thickness steel (max.): 8 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 4 mm, sheet thickness brass (max.): 4 mm, sheet thickness copper (max.): 4 mm, pipe diameter (max.): 240 mm, pipe length (max.): 6,050 mm, working length: 8,050 mm, working width: 250 mm, working height: 250 mm, travel distance X-axis: 400 mm, travel distance Y-axis: 6,500 mm, travel distance Z-axis: 280 mm, feed rate X-axis: 116 m/min, feed rate Y-axis: 131 m/min, feed rate Z-axis: 30 m/min, positioning accuracy: 0.03 mm, repeat accuracy: 0.05 mm, workpiece weight (max.): 100 kg, power: 3,000 kW (4,078.86 HP), input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, compressed air connection: 8 bar, overall weight: 5,000 kg, total length: 12,500 mm, total width: 2,400 mm, total height: 2,550 mm, warranty duration: 12 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, With a completely redesigned machine concept, it combines maximum stability, highest efficiency, precise processing, and intelligent automation in a single system. It is optimally suited for processing a wide range of metal tubes and profiles—flexible, reliable, and powerful. A patented, innovative design combined with an exclusive automatic loading and unloading system ensures a significant increase in productivity. The system operates faster, more stably, and more intelligently and is available in various configurations to precisely match your individual requirements. Thanks to improved dynamics and increased performance, the machine delivers outstanding results across all processing operations—whether cutting, drilling, or complex contour cutting. The cutting quality is of the highest standard: smooth surfaces, minimal thermal impact, and virtually no residues or reworking required. Numerous patented core technologies guarantee consistently high machining accuracy and perfect results—even during demanding continuous operation. Even after many years of intensive use, the system’s performance remains at an exceptionally high level, making it a sustainable, future-proof investment for your production. Cutting power: 3000 W Laser source: MAX Photonics Laser head: BOCI Autofocus Iodpfxjy R I Rxo Ahqjtg Maximum tube length: 6500 mm Tube diameter: 240 mm Acceleration: 1.2G

Condition: new, functionality: fully functional, Year of construction: 2026, control type: PLC-controlled, degree of automation: semi-automatic, actuation type: electric, controller manufacturer: Siemens, laser type: fiber laser, laser source manufacturer: Max Photonics, laser source model: MAX 6kW mit CE, laser power: 12,000 W, sheet thickness (max.): 30 mm, sheet thickness steel (max.): 30 mm, sheet thickness stainless steel (max.): 25 mm, sheet thickness aluminum (max.): 15 mm, sheet thickness brass (max.): 15 mm, sheet thickness copper (max.): 15 mm, table length: 4,000 mm, table width: 2,000 mm, working length: 4,000 mm, working width: 2,000 mm, positioning accuracy: 0.3 mm, repeat accuracy: 0.3 mm, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, compressed air connection: 8 bar, overall weight: 8,500 kg, total length: 10,500 mm, total width: 4,200 mm, warranty duration: 12 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, Fiber Laser Cutting Machine 4020, 6 kW – Overview Safety & Protection Fully enclosed metal safety enclosure with radiation-proof doors and windows. Environmentally friendly and operator-safe. Work Platform High and low parallel platform: Front end: Laser cutting area. Rear end: Loading and unloading area. No mutual interference → increased work efficiency. Machine Structure 10 kW bed structure: Time-segmented, sectional dust extraction. Effective heat dissipation, resistant to thermal deformation. Industrial auxiliary equipment: air conditioner, dedicated cooling system, constant temperature & humidity → stable performance & extended service life. Precision Guarantee: Bed processed with large gantry milling machine. Industrial-grade linear guides, racks, and ball screws. Full servo control, double-sided dual drive. High industrial quality and precision. German assembly technology: Precision calibration with laser interferometers. Fine craftsmanship, easier maintenance. Control & Software FSCUT 6000 control system (included). FSCUT software suite: Industry-standard, secure, and user-friendly software. Supports intelligent networking. Professional nesting software: CypNest (included). Core Components Laser cutting head: BOCI BLT442 Laser source: MAX 6 kW, CE certified Water chiller: HANLI 12 kW Iodoy R I N Iepfx Ahqstg Linear guide: TAIWAN DTX 30+20+20 Rack: TAIWAN JT Reducer: Germany Techmach Cameras: 2 units Servo motor: BOCHU Proportional valve: Felton Electronic components: SCHNEIDER Triple air inlet: nitrogen, oxygen, air Lubrication system: Automatic oil supply system Accessories 30 protection lenses, 30 nozzles, toolbox. Optional: Air compressor ARS-30HP-XF-1, 1.6 MPA, dust collector 7.5 kW.

Condition: new, functionality: fully functional, Year of construction: 2026, control type: PLC-controlled, degree of automation: semi-automatic, actuation type: electric, controller manufacturer: Siemens, laser type: fiber laser, laser source manufacturer: Max Photonics, laser source model: MAX 12kW mit CE, laser power: 12,000 W, sheet thickness (max.): 40 mm, sheet thickness steel (max.): 40 mm, sheet thickness stainless steel (max.): 30 mm, sheet thickness aluminum (max.): 20 mm, sheet thickness brass (max.): 15 mm, sheet thickness copper (max.): 15 mm, table length: 4,000 mm, table width: 2,000 mm, working length: 4,000 mm, working width: 2,000 mm, positioning accuracy: 0.3 mm, repeat accuracy: 0.3 mm, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, compressed air connection: 8 bar, overall weight: 8,500 kg, total length: 10,500 mm, total width: 4,200 mm, warranty duration: 12 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, Fiber laser cutting machine 4020, 12 kW – Overview Safety & Protection Fully enclosed metal safety cabin with radiation-protected doors and windows. Environmentally friendly and safe for operators. Working Platform Up/down parallel working platform: Front end: Laser cutting. Rear end: Loading and unloading. No mutual interference → increased work efficiency. Machine Structure 10 kW bed structure: Time-segmented, zoned dust extraction. Robust heat dissipation, resistant to thermal influences. Industrial auxiliary equipment: Air conditioning, specialized cooling system, constant temperature & humidity → stable performance & longer service life. Precision Guarantee: Bed processed by large gantry milling machine. Industrial-grade guide rails, rack and pinion, and screw drives. Full servo control, double-sided dual drive. High industrial standard and precision. German assembly technology: Precision calibration with laser interferometers. Fine craftsmanship, easier maintenance. Control & Software FSCUT 6000 control system (included). FSCUT software package: Market-standard, safe, and user-friendly software. Supports intelligent networking. Professional nesting software: CypNest (included). Core Components Laser cutting head: BOCI BLT442 Laser source: MAX 12 kW, CE-certified Water chiller: HANLI 12 kW Guide rails: TAIWAN DTX 30+20+20 Machine frame: TAIWAN JT Reducer: Germany Techmach Cameras: 2 pieces Servo motor: BOCHU Proportional valve: Felton Electrical components: SCHNEIDER Triple air inlet: Nitrogen, Oxygen, Air Lubrication system: Automatic oil supply system Accessories Itjdjy R I Nnepfx Ahqeg 30 protective lenses, 30 nozzles, toolbox. Optional: Air compressor ARS-30HP-XF-1.6 MPA, dust collector 7.5 kW.

Condition: new, functionality: fully functional, Year of construction: 2026, control type: PLC-controlled, degree of automation: semi-automatic, actuation type: electric, controller manufacturer: Siemens, laser type: fiber laser, laser source manufacturer: Max Photonics, laser source model: MAX 6 kW mit CE, laser power: 6,000 W, sheet thickness (max.): 25 mm, sheet thickness steel (max.): 25 mm, sheet thickness stainless steel (max.): 20 mm, sheet thickness aluminum (max.): 15 mm, sheet thickness brass (max.): 10 mm, sheet thickness copper (max.): 10 mm, table length: 3,000 mm, table width: 1,500 mm, working length: 3,000 mm, working width: 1,500 mm, positioning accuracy: 0.3 mm, repeat accuracy: 0.3 mm, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, compressed air connection: 8 bar, overall weight: 8,000 kg, total length: 8,500 mm, total width: 3,500 mm, warranty duration: 12 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, Fiber Laser Cutting Machine 1530, 12 kW – Overview Safety & Protection Fully enclosed metal protective chamber with radiation-resistant doors and windows. Environmentally friendly and safe for operators. Work Platform High- and low-positioned parallel platform: Front end: laser cutting. Rear end: loading and unloading. No mutual interference → increased work efficiency. Machine Structure 10 kW bed structure: Time-segmented, zoned dust extraction. Superior heat dissipation, resistant to thermal effects. Industrial auxiliary equipment: air conditioning, special cooling system, constant temperature & humidity → stable performance & longer service life. Precision Assurance: Bed processed by large gantry milling machine. Industrial-grade guide rails, racks, ball screws. Full servo drive, double-sided dual drive. High industrial quality and precision. German assembly technology: Precision calibration with laser interferometers Fine craftsmanship, easier maintenance. Control & Software FSCUT 6000 control system (included). FSCUT software suite: Market-proven, safe, and user-friendly software. Supports smart networking. Professional nesting software: CypNest (included). Core Components Laser cutting head BOCI BLT442 Laser source MAX 6 kW, CE certified Water chiller HANLI 6 kW Guideway TAIWAN DTX 30+20+20 Frame TAIWAN JT Reducer Germany Techmach Itodey R I Nhepfx Ahqsg Cameras (2 pcs) Servo motor BOCHU Proportional valve Felton Electronic components SCHNEIDER Triple air inlet: nitrogen, oxygen, air Lubrication system: automatic oil supply system Accessories 30 protective lenses, 30 nozzles, toolbox. Optional: air compressor ARS-30HP-XF-1,6 MPA, dust collector 7.5 kW.

Condition: new, functionality: fully functional, Year of construction: 2026, control type: PLC-controlled, degree of automation: semi-automatic, actuation type: electric, controller manufacturer: Siemens, laser type: fiber laser, laser source manufacturer: Max Photonics, laser source model: MAX 12kW mit CE, laser power: 12,000 W, sheet thickness (max.): 40 mm, sheet thickness steel (max.): 40 mm, sheet thickness stainless steel (max.): 30 mm, sheet thickness aluminum (max.): 20 mm, sheet thickness brass (max.): 15 mm, sheet thickness copper (max.): 15 mm, table length: 3,000 mm, table width: 1,500 mm, working length: 3,000 mm, working width: 1,500 mm, positioning accuracy: 0.3 mm, repeat accuracy: 0.3 mm, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, compressed air connection: 8 bar, overall weight: 8,000 kg, total length: 8,500 mm, total width: 3,500 mm, warranty duration: 12 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, Fiber Laser Cutting Machine 1530, 12 kW – Overview Safety & Protection Fully enclosed metal safety housing with radiation-shielded doors and windows. Environmentally friendly and safe for operators. Working Platform High-low parallel platform: Front end: Laser cutting. Rear end: Loading and unloading. No mutual interference → increased work efficiency. Machine Structure 10 kW bed structure: Segmented dust extraction with time-division control. Enhanced heat dissipation, resistant to thermal effects. Industrial auxiliary equipment: air conditioner, special cooling system, constant temperature & humidity → stable performance & longer service life. Precision Guarantee: Bed machined by large gantry milling machine. Industrial-grade guide rails, gears, and ball screws. Fully servo-controlled, double-sided dual drive. High industrial quality and precision. German assembly technology: Precision calibration with laser interferometers Fine craftsmanship, easier maintenance. Control & Software FSCUT 6000 control system (included). FSCUT software package: Market-standard, safe, and user-friendly software. Supports intelligent networking. Professional nesting software: CypNest (included). Core Components Laser cutting head BOCI BLT442 Laser source MAX 12 kW, CE certified Chiller HANLI 12 kW Guide rails TAIWAN DTX 30+20+20 Frame TAIWAN JT Reducer Germany Techmach Camera (2 units) Servo motor BOCHU Proportional valve Felton Ijdpfx Ahoy R I Nbeqjtg Electronic components SCHNEIDER Triple air inlets: nitrogen, oxygen, air Lubrication system: automatic oil supply Accessories 30 protective lenses, 30 nozzles, tool kit. Optional: ARS-30HP-XF-1,6 MPA air compressor, 7.5 kW dust collector.

Condition: excellent (used), functionality: fully functional, Year of construction: 2023, machine/vehicle number: 6500034407, degree of automation: automatic, power: 6 kW (8.16 HP), Equipment: CE marking, centralized greasing system, cooling unit, dust extraction, emergency stop, fume extraction, BODOR M3 – fiber laser metal tube cutting machine, MFG 2023; SN: 6500034407 Iodpfx Aoy R Etdshqjtg EtherCAT bus control: advanced system in the industry, more accurate control, faster response, and higher processing efficiency. Independently-developed Bodor Thinker system: third generation bus system with excellent performance and greatly reduced system failure. New Bodor style design: international IF design award winner. Classic and iconic design of Bodor products is distinguishable in the market. BodorNest Tube: a variety of nesting methods catered to customers various cutting demands. Independently developed spike-shaped laser cutting head to make cutting easier Function&parameter list Tube size range-Square tube 25 - 356mm, I-beam 10#-22# Option the special jaws, I-beam 100-320mm; Hea profiles 100-320mm Basic parameter (Metal Plate Cutting) Cutting Capacity (MaximumThickness): Carbon Steel 18 mm Basic parameter (Metal Plate Cutting) Cutting Capacity (MaximumThickness): Stainless Steel 18 mm Operation parameter Shortest remaining material - no waste of materials Max. length of machinable tubes 12000mm Maximum tube weight: 800kg Overall sizes: 27430mm×2710mm×3160mm Machine weight: 16000kg Positioning accuracy: 0.06mm/m Repeated positioning accuracy: 0.04mm Max. speed of chuck with no-load 75r/min Max. speed of chuck feed axis 80m/min Max. speed of laser head moving axis 60m/min Max. acceleration of chuck feeding axis 1G Maximum acceleration of laser head moving axis 0.6G Max. speed of Z-axis 60m/min The central wavelength of an optical fiber laser is 1080 nm, or one-tenth the wavelength of a CO2 laser. The processing costs are lowered to a minimum since the output beam has superior quality, a larger power density, and is easier to absorb by metal materials. Optical fibre laser transmitted through the whole machine with simple optical path, stable structure. External optical path is maintenance-free. Nesting software compatible with Tekla Bodor Nest supports direct NC1 files import. Bodor Nest Tube supports Tekla online import. Compatibility: compatible with various versions of Tekla software. One click to split the drawing: automatically split the whole drawing into individual parts. Intelligent drawing recognition: directly detects the material properties, thickness, quantity, etc. Multi-layer display: marking, part outline, part labelling, etc., are displayed in different layers Intelligent matching: automatically matching appropriate cutting process parameters with identified material information. Efficient nesting: Automatic calculation for the optimal nesting solution to maximize plate utilization. Auxiliary loading device Integrated material table, material selection, and loading function. After placing the raw materials at according workstation, it can complete the cyclic loading of round, square, rectangular pipe, channel steel, and I-beam, which can significantly improve the processing efficiency and reduce labour cost. Fume filter for Laser Cutting Machine Price: 205.700 Euro + VAT, negotiable, ExWorks Arad /Romania Irrtum, Änderungen und Zwischenverkauf vorbehalten / Subject to errors, changes, and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabilă. We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana.

Condition: used, functionality: fully functional, Year of construction: 2024, operating hours: 8,736 h, machine/vehicle number: R1119022, control type: CNC control, degree of automation: automatic, actuation type: electric, controller manufacturer: Bystronic, controller model: P8005A, laser type: CO₂ laser, laser source manufacturer: Bystronic, laser source model: ByLaser 4400, laser hours: 8,736 h, laser power: 4,400 W, laser wavelength: 10 nm, Offered is a laser source from Bystronic (ByLaser 4400). All maintenance and repairs were performed by Bystronic. Operating hours may change as the machine including the laser source is in daily operation. Handover is by arrangement, dismantling is the buyer's responsibility. Parts can also be sold individually as spare part donors. Iodpsy Rzi Uofx Ahqjtg

Condition: used, functionality: fully functional, Year of construction: 2011, operating hours: 35,509 h, machine/vehicle number: R1119022, control type: CNC control, degree of automation: automatic, actuation type: electric, controller manufacturer: Bystronic, controller model: P8005A, laser type: CO₂ laser, laser source manufacturer: Bystronic, laser source model: ByLaser 4400, laser hours: 35,509 h, laser power: 4,400 W, laser wavelength: 10 nm, Offered is a laser source from Bystronic (ByLaser 4400). All maintenance and repairs were performed by Bystronic. Operating hours may change as the machine including the laser source is in daily operation. Handover is by arrangement, dismantling is the buyer's responsibility. Parts can also be sold individually as spare part donors. Itodey Rzg Tepfx Ahqeg

Condition: excellent (used), functionality: fully functional, Year of construction: 2012, operating hours: 78,203 h, control type: CNC control, controller manufacturer: Trumpf, laser type: CO₂ laser, laser hours: 38,762 h, laser power: 4,000 W, sheet thickness (max.): 15 mm, sheet thickness steel (max.): 15 mm, sheet thickness stainless steel (max.): 10 mm, sheet thickness aluminum (max.): 15 mm, table length: 4,000 mm, table width: 2,000 mm, working width: 2,000 mm, travel distance X-axis: 4,000 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 115 mm, power: 77 kW (104.69 HP), type of cooling: water, overall weight: 16,000 kg, year of last overhaul: 2025, Equipment: cooling unit, We offer this Trumpf Laser TruLaser 3040 (L32) laser cutting machine, model TruLaser 3040, in very good condition, year of manufacture 2012. Trumpf Laser TruLaser 3040 (L32), CO2 Laser Year of manufacture: 2012, used by the first and sole owner from new Cutting unit power: 4kW Table dimensions: 2x4 [m] X-axis: 4000 mm Y-axis: 2000 mm Z-axis: 115 mm Maximum sheet thickness: - Mild steel: 15 mm - Aluminium: 15 mm - Stainless steel: 10 mm Weight: 16,000 kg Rated power: 77kW Closed-circuit cooling system Good condition: optics and resonator system overhauled (2025) and conveyor belt replaced (2026), machine serviced under Classic contract (every 6 months) by authorized Trumpf service Operating hours: laser beam - 38,762 h, machine - 78,203 h CNC control Machine number: A1240A0214 Isdoy Rxnuopfx Ahqstg Location: Inowrocław, Poland Price without VAT For any questions or if you need more information, please send a message or contact us by phone. Tel. +48 722 151 062

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2010, operating hours: 26,000 h, machine/vehicle number: R1011250, laser power: 4,400 W, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 170 mm, workpiece weight (max.): 890 kg, Laser source and frequency converter have been renewed! TECHNICAL DETAILS Working Area and Cutting Area Nominal plate size X: 3,000 mm Nominal plate size Y: 1,500 mm Cutting area X-axis: 3,048 mm Cutting area Y-axis: 1,524 mm Cutting head Z-lift: 170 mm Workpiece weight: max. 890 kg Dynamics and Accuracy Ijdpfxjy Rt Ezo Ahqstg Positioning deviation: ±0.1 mm Positioning scatter: ±0.05 mm Edge detection accuracy: ±0.5 mm Positioning speed X/Y-axis (axial parallel): max. 80 m/min Positioning speed X/Y-axis (simultaneous): max. 113 m/min Axis acceleration: max. 4.5 m/s² Laser Source Laser power: 4,400 W Laser source: Bylaser 4400 Possible laser sources: Bylaser 3000 / Bylaser 4400 / Bylaser 5200 ARC / Bylaser 6000 MACHINE DETAILS Dimensions and required space Transport system standard height: 3,650 mm Transport system height to magazine: 4,350 mm Material trolley length: 3,000 mm Additional length for extension magnet: 200 mm Material trolley width: 1,600 mm Material trolley height without plate stack: 917 mm Standard lifting height: 550 mm Lifting height to magazine: 1,150 mm Lifting height with stacked tables: 800 mm Transport data and weights Travel unit with lifting unit: 1,300 kg Vacuum gripper frame with double fork system: 1,200 kg PLC cabinet: 500 kg Material trolley: 800 kg Total transport weight ByTrans 3015: 3,800 kg Equipment and Features Vacuum gripper frame plate thickness (loading): max. 25 mm Vacuum gripper frame plate weight (loading): max. 900 kg Number of vacuum grippers: 42 Weight per gripper: max. 45 kg Compressed air: 6 bar Vacuum: -0.6 bar Double fork system plate thickness (unloading): max. 25 mm Double fork system plate weight (unloading): max. 900 kg Fork travel path: 2 x 790 mm Cutting hours: 26,000 h EQUIPMENT ByTrans 3015 Extended Bylaser 4400 Shuttle table Loading arm Integrated 4th rotary axis Vacuum gripper frame Loading unit with suction gripper frame Double fork system Material trolley Vacuum pump Plate separator Double sheet detection Cassette trolley Air conditioning Control cabinet with signal lamp and emergency stop Safety fence Photoelectric sensors ByTower storage system

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2006, operating hours: 14,434 h, controller model: Siemens Sinumerik 840D, laser power: 4,000 W, sheet thickness steel (max.): 20 mm, sheet thickness stainless steel (max.): 15 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, Equipment: safety light barrier, TECHNICAL DETAILS Laser power: 4,000 W Travel range X-axis: 3,000 mm Travel range Y-axis: 1,500 mm Sheet metal thickness, steel (max.): 20 mm Sheet metal thickness, stainless steel (max.): 15 mm MACHINE DETAILS Control model: Siemens Sinumerik 840D Itjdsy Rk Uyopfx Ahqjg Beam-on hours: 14,434 h Power-on hours: 39,875 h EQUIPMENT Closed machine frame with integrated laser unit Laser unit: CO2 laser TFL 3200 high-frequency unit, maintenance-free turbo-radial blower, mirror telescope Automatic pallet changer Longitudinal conveyor belt for small parts/waste Drives: Maintenance-free three-phase AC servo motors Additional high-dynamic Xp-axis Cutting head quick-change device Laser cutting head with 5" lens and 7.5" lens Cutting gas pressure setting, programmable APC capacitive height control and process control Automatic focus position adjustment AutoLas Plus Laser power control Positioning laser diode HI-LAS high-pressure cutting Fast processing with SprintLAS ContourLAS for producing smaller holes PMS plasma sensor Automatic sheet metal edge detection Programmable power cycles Compressed air cutting PCS Process Control System Microweld Spraying device for safe thick sheet metal processing Automatic shutdown Work area lighting Workshop programming ToPs 100 lite Control: Siemens Sinumerik 840D Open control system based on PC, easy operation, online help, integrated e-shop, diagnostic function, maintenance log, technology data, teleservice Safety equipment: Multi-beam light barriers, beam guidance completely encapsulated and ventilated, monitoring system, multi-chamber extraction and compact dust collector, protective cabin

Condition: repair required (used), functionality: limited functionality, Year of construction: 2017, control type: CNC control, degree of automation: automatic, actuation type: electric, laser type: fiber laser, laser source manufacturer: IPG, laser source model: YLS-4000-CUT, We offer this repair-required VIRS MSF 3001.15L laser cutting machine, year 2017. Manufacturer: Microstep / VIRS Model: MSF 3001.15L Year of manufacture: 2017 Iedpoy Ri Tuofx Ahqetg Modules 1, 4, and 5 automatically lock immediately after cutting and require unlocking by IPG. Half of the 2 kW power is available. If you have any additional questions or need more information, please send us a message or call us.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2019, controller model: Siemens 840D, laser type: fiber laser, laser power: 2,000 W, sheet thickness (max.): 8 mm, overall weight: 20,000 kg, No reserve – guaranteed sale to the highest bidder! DURMA laser cutting system – fully equipped! TECHNICAL DETAILS Maximum sheet thickness: 8 mm Maximum steel sheet thickness: 8 mm Maximum stainless steel sheet thickness: 4 mm Maximum aluminum sheet thickness: 6 mm Maximum tube diameter: 170 mm Maximum tube length: 6,500 mm Maximum round tube diameter: 170 mm Maximum square profile: 120 x 120 mm Maximum rectangular tube: 150 x 100 mm Minimum tube diameter (automatic): 20 mm Minimum tube diameter (manual): 12 mm Minimum processable tube length: 185 mm Minimum processable wall thickness: 0.8 mm Maximum processable wall thickness (mild steel, 2 kW laser): 8 mm Maximum processable wall thickness (stainless steel, 2 kW laser): 4 mm Maximum processable wall thickness (AlMg3, 2 kW laser): 6 mm Repeatability: 0.05 mm Maximum profile length: 6,500 mm Minimum profile length for automatic loading: 3,000 mm Standard discharge length: 4,000 mm Maximum profile weight: 37.5 kg/m Maximum loading capacity: 3,000 kg Possible loadable profiles: round, square, rectangular, elliptical Itedsy N Rqrspfx Ahqjg MACHINE DETAILS Laser type: Fiber laser Laser source manufacturer: IPG Laser power: 2,000 W Power: 2 kW (2.72 HP) Control system model: Siemens 840D Automation level: Automatic Actuation type: Electric Dimensions & Weight Dimensions (L x W x H): approx. 16,000 x 7,400 x 2,364 mm Weight: approx. 20,000 kg EQUIPMENT CE marking Documentation/manual Cooling unit Emergency stop switch Fume extraction Safety light curtain Central lubrication system Precitec Autofocus Procutter cutting head F 150 (Focus) Control cabinet air conditioning Manual loading Manual unloading Laser positioning diode Central lubrication unit Small parts disposal box Illuminated cutting chamber IPG laser source 2 kW Vanterm compact filter unit Automatic loading system (6,500 mm) Unloading unit (6,000 mm) Discharge conveyor, inc. small parts conveyor (rear discharge) Automatic cut seam detection Automatic real-time measurement system for centering chuck Calcium carbonate dosing unit