Topmed Intl.

Condition: ready for operation (used), Year of construction: 2008, travel distance X-axis: 800 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 800 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530 with smarT.NC, total height: 2,800 mm, total width: 2,250 mm, table width: 920 mm, table length: 900 mm, table load: 1,800 kg, overall weight: 14,000 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 40,000 W, number of axes: 3, This 3-axis Alzmetall GS 800/3 vertical machining centre was manufactured in 2008. It features an impressive X-axis travel of 800 mm, Y-axis travel of 800 mm, and Z-axis travel of 500 mm. The machine is equipped with a HEIDENHAIN iTNC 530 control and a robust table surface area of 920 x 900 mm, supporting a maximum table load of 1,800 kg. If you are looking to get high-quality machining capabilities, consider the Alzmetall GS 800/3 machine we have for sale. Contact us for further details. - Distance Spindle to Rigid Table: 150 – 650 mm - Table T-Slots: 9 T-slots according to DIN 650 in X-direction, 14 H12 width, 100 mm pitch, 14 H7 center alignment slot, table lowered by 80 mm - Spindle Type: Water-cooled high-frequency motor spindle with hybrid spindle bearings and oil-air lubrication - Spindle Taper: HSK-A63 according to DIN 69893 -- Max. Torque: 139 Nm at 25% duty cycle - Spindle Features: New spindle in 2025, thermal expansion compensation, sealing air seal, air blow through spindle center - Rapid Traverse (X/Y/Z): 45 m/min - Max. Acceleration (X/Y/Z): 10 m/s² - Max. Feed Force (X/Y/Z): 10 kN at 40% duty cycle - Measuring Systems: Dual direct linear measuring systems for X/Y, direct linear measuring system for Z - Positioning Accuracy (Tp): 0.007 mm according to DIN ISO 230-2 - Tool Magazine: Chain magazine with 33 tool positions - Tool Change System: Pick-up system - Max. Tool Diameter: 90 mm (full configuration) / 130 mm (with free adjacent positions) - Max. Tool Length: 300 mm - Max. Tool Weight: 10 kg - Max. Total Tool Weight: 160 kg - Tool Change Time: Approx. 2 seconds - Chip-to-Chip Time: Approx. 6 seconds - Operating Voltage: 3x 400 V - Mains Frequency: 50 Hz - Total Rated Current: 55 A - Mains Supply Fuses: 63 A gG - Required Supply Pressure: Min. 6 bar - Required Network System: TN network - Transport Dimensions: Approx. 2,250 mm (W) x 4,760 mm (D) x 2,800 mm (H) - Additional Equipment & Features: - HEIDENHAIN TS 640 3D touch probe with infrared transmission - HEIDENHAIN TT 140 automatic tool measurement - HR 410 electronic handwheel - Automatic roller shutter roof cover - Scraping-belt chip conveyor (for short metal chips up to 80 mm length) - All-round sheet steel enclosure - Stainless steel interior lining of the machining area - Work area lighting - Electrically secured horizontal sliding door with mechanical locking - Control cabinet cooling- Missing/Excluded Components: Coolant tank is NOT included (no coolant tank, no pumps, no chip flushing hose) Gksdpsz R Sz Eofx Ahdsc

Condition: used, Year of construction: 2017, Working range X-axis: 550 mm Y-axis: 450 mm (tool change position 725 mm) Z-axis: 375 mm Workpiece carrier Double swivel carrier with counterbearing and crown gear, swivel time 0/180°: approx. 3.0 s A- and U-axis for fixture plate: max. ø475 × 830 mm Drive system: torque motor Load capacity: 2 × 360 kg Speed range A- and U-axis: 1–50 rpm C- and W-axis (optional): 2 or 4 satellites Work spindle Tool interface: HSK-A63 Speed range: 1–10,000 rpm (optional 1–17,500 rpm) Run-up time to max. speed: < 0.4 s (< 1.0 s with optional spindle) Spindle bearings: ø80 mm Power: 32 kW (40% duty cycle) Torque: 72 Nm (40% duty cycle) Feed drive Drive system: ball screw Rapid traverse X/Y/Z: 75 m/min Axis acceleration X/Y/Z: 10 / 10 / 15 m/s² Max. feed thrust X/Y/Z: 8,000 N Accuracy Position measuring system: direct, absolute Positioning tolerance X/Y/Z: Tp = 0.008 mm Tool magazine Tool change system: pick-up Capacity: 40 pockets (optional 64 or 80) Max. tool diameter: 70 mm / 160 mm (with free adjacent pockets) Gsdpfoz R Szrjx Ahdjkc Max. tool length: 275 mm Max. tool weight: 7.5 kg Chip-to-chip time: approx. 2.5 s Weight and dimensions Total weight: approx. 9,500 kg Transport dimensions (W × H × L): 2.75 × 2.85 × 3.65 m Machine installed (W × H × L): 3.85 × 3.70 × 6.30 m Connected load Operating voltage: 3 × 400 V, 50 Hz, TN-S/TN-C Total connected load: approx. 64 kVA Mean air consumption: 0.5 Nm³/min (6 bar) CNC control Siemens SINUMERIK 840D

Condition: used, Year of construction: 2024, Machine has 0 cutting hours Main spindle machining capacity Max. machining diameter: ø16 mm Max. machining length without re-chucking: 200 mm Max. front drilling diameter: ø10 mm Max. front tapping diameter: M8 Main spindle through-hole: ø20 mm Main spindle speed: max. 12,000 rpm Back spindle Max. back spindle chucking diameter: ø16 mm Max. back drilling diameter: ø8 mm Max. back tapping diameter: M6 Back spindle speed: max. 12,000 rpm Gang tool post (rotary tools) Max. drilling diameter ø5 mm, max. tapping diameter M5 Spindle speed: max. 8,000 rpm Turret (rotary tools) Max. drilling diameter ø5 mm, max. tapping diameter M5 Spindle speed: max. 8,000 rpm Number of stations: 10 + α Tooling Number of mountable tools: up to 32 + α Turning tools on gang tool post: 5 × 16 mm Rotary tools on gang tool post: 5–7 Back tool post: 5 fixed tools Drill sleeve: ø19.05 mm Collet, main and back spindle: 138E Guide bush: F605 Feed rates Rapid traverse, all axes (except X2 and Y2): 32 m/min X2 axis: 16 m/min Y2 axis: 8 m/min Motors Main spindle motor: 2.2 / 3.7 kW Back spindle motor: 0.75 / 1.5 kW Rotary tool drives (gang tool post and turret): 0.69 kW Control and dimensions Control: Mitsubishi Meldas M730 Dimensions (W × D × H): 2,780 × 1,340 × 1,790 mm Gkodpfxjz R Szlj Ahdsc Weight: 2,900 kg Center height: 1,150 mm Option: LFV technology (Low Frequency Vibration) for chip breaking The machine comes with 5 driven tool holders and one holder for the turret.

Condition: used, functionality: fully functional, mileage: 75,932 km, number of beds: 2, number of seats: 4, fuel type: diesel, gearing type: automatic, color: white, first registration: 01/2022, chassis manufacturer: Mercedes Benz, chassis model: Marco Polo 240d 2.0, total length: 5,140 mm, total width: 1,920 mm, total height: 1,980 mm, axle configuration: 2 axles, emission class: euro6, fuel tank capacity: 70 l, overall weight: 3,100 kg, empty load weight: 2,380 kg, steering wheel position: left, number of previous owners: 1, Year of construction: 2022, machine/vehicle number: W1V44781313950388, Equipment: ABS, air conditioning, airbag, all-season tires, car registration, central locking, electronic stability program (ESP), fog lights, full service history, onboard kitchen, power assisted steering, second-hand vehicle warranty, single beds, soot filter, twin bed, AVAILABLE NOW | License Plate: GG-668-VP | Mileage: 75,932 km | Location: Bari | Our Mercedes Marco Polo campervan is the perfect choice for those seeking a premium, stylish, and comfortable travel experience. Whether you’re planning a city getaway or a long adventure, this van offers the ideal combination of performance, comfort, and reliability. Gkedpfx Aoz R Sy Ujhdec Why buy the Mercedes Marco Polo? ✔ Spacious – With a length of 5.1 m, a width of 1.9 m, and a height of 2 m, the Marco Polo is easy to drive and park. ✔ Powerful and fuel-efficient – 2.0 diesel engine, 240d, 190 hp, automatic transmission, and Euro 6 emissions class. ✔ Ideal for up to 4 people – Equipped with 4 seats and 4 sleeping places: 1 convertible double bed in the cabin and 1 double bed in the pop-up roof. ✔ Well-equipped for every trip – Includes a kitchenette, a convertible dining table, and a removable outdoor shower. ✔ Safe and reliable – Includes ABS, ESP, central locking, parking sensors, and tire pressure monitoring. Why buy from Indie Campers? 💰 Satisfaction or your money back guarantee – Try the van for 14 days, and if you’re not satisfied, we’ll refund you. 🚐 Try before you buy – Rent a vehicle first to make sure it’s the right one for you. 🔒 1-year warranty – Warranty coverage is provided according to the terms and conditions of CarGarantie for purchases by private customers, based on location. Full terms and conditions are available upon request. 💵 Flexible financing – We offer flexible payment plans to suit your needs, depending on the location. 📝 Flexible viewings – We can schedule an appointment to view the vehicle at the date and time that is most convenient for you, in person or via video call. 🌍 Relocation – Is the vehicle not located in the right place? We offer relocation throughout Europe. ✔ Up-to-date inspection and ready to go. Start your next adventure today! The Marco Polo campervan is in high demand. Don’t miss this opportunity: contact us to schedule a viewing and make it yours today.

Condition: new, Year of construction: 2026, functionality: fully functional, power: 13.5 kW (18.35 HP), input current: 25 A, input frequency: 50 Hz, pressing force: 160 t, table width: 740 mm, table length: 1,300 mm, table height: 200 mm, ram plate width: 920 mm, ram plate length: 580 mm, distance table to ram: 600 mm, total length: 2,500 mm, total width: 1,700 mm, total height: 3,500 mm, overall weight: 15,000 kg, Equipment: CE marking, documentation/manual, safety light barrier, TEHSLA EPC160 – 160 TON MECHANICAL ECCENTRIC PRESS MAIN TECHNICAL DATA - Press Force: 160 tons - Stroke Rate: 24–52 strokes/min (adjustable) - Stroke Length: 16–160 mm (adjustable) - Ram Adjustment: 0–110 mm (motorized) - Maximum Opening Between Tables: 600 mm - Table Dimensions: 1,300 × 740 mm Gkedpfx Ahjz R Sy Ijdoc - Ram Dimensions: 920 × 580 mm - Main Motor Power: 15 kW - Control Panel: SIEMENS SIMATIC HMI MTP1200 Comfort PRO - Clutch System: Wet clutch - Safety Light Curtains: LEUZE - Ram Guidance: Eight-sided precision guiding system MACHINE TECHNICAL SPECIFICATIONS Machine Frame: Heavy-duty welded steel construction, engineered for high rigidity, structural stability and long-term durability under demanding industrial operating conditions. Control System: SIEMENS control system with SIMATIC HMI MTP1200 Comfort PRO touchscreen interface. Clutch System: Wet clutch system designed for reliable operation and long service life. Stroke Adjustment: Adjustable eccentric stroke from 16 to 160 mm. Stroke Speed Adjustment: Variable operating speed from 24 to 52 strokes per minute on plc. Ram Adjustment: Motorized ram adjustment, 0–110 mm. Guidance System: Precision eight-sided ram guiding system, providing excellent stability, accurate ram movement and reduced wear during continuous operation. Lubrication: Automatic circulating lubrication system. Overload Protection: Hydraulic overload protection system. Safety Light Curtains: LEUZE safety light curtains for operator protection. Safety Monitoring: Oil and air pressure monitoring with alarm functions. Operation Modes: Inch / Single Stroke / Continuous Stroke. Safety Operation: Two-hand control system. CE Compliance: Manufactured in accordance with applicable CE safety requirements. OPTIONAL EQUIPMENT & UPGRADES - Pneumatic holding systems - Mechanical or pneumatic ejector systems - Die cushions / pneumatic cushions - Customized ejector and cushion configurations - Additional protective safety guarding - Remote monitoring and control systems - Remote diagnostics, servicing and troubleshooting - Additional automation solutions according to customer requirements WARRANTY: 12 months CUSTOM PRESS MANUFACTURING TEHSLA is a Slovenian manufacturer of industrial hydraulic and mechanical eccentric presses. In addition to the advertised EPC160+ model, we manufacture customized eccentric presses with different pressing capacities, working table dimensions, stroke lengths and technical configurations. Our machines can be equipped with additional automation systems, ejectors, die cushions and other customer-specific solutions. MADE IN SLOVENIA Manufacturer: TEHSLA Model:EPC160+ Country of Manufacture: Slovenia, European Union Machine Location:Ljubljana, Slovenia Inspection & Test Run:Available by prior arrangement. Contact us for further technical information, machine availability, customization options or a quotation. Other press capacities, dimensions and customized configurations are available directly from the manufacturer upon request.

Condition: good (used), Year of construction: 2006, operating hours: 1,300 h, JLG 2646ES scissor lift, aerial work platform, 2006 / 1300 hours, 10-meter working height. A video can be sent via WhatsApp. We have a continuous stock; please see our website. Prices are quoted ex-works Nuland. Van de Wert Trading B.V. has a varying stock of machines, trucks, trailers, and attachments. All our deliveries are at trade prices, in AS-IS condition, without warranties (see our general terms and conditions). You can make a non-binding appointment for a viewing and/or test drive. Please call in advance as we are not always on-site. Van de Wert Trading B.V. Gkodpfx Ahjz R Syzsdoc Bedrijfsstraat 3 5391 LR Nuland

Condition: good (used), Year of construction: 2006, operating hours: 975 h, JLG 2646ES scissor lift, 2006 / 975 hours, 10-meter working height. A video can be sent via WhatsApp. We have a continuous stock; see our website. Prices are quoted ex-Nuland. Van de Wert Trading B.V. has a varying stock of machines, trucks, trailers, and attachments. All our deliveries are offered at trade prices in AS-IS condition without guarantees (see our general terms and conditions). You can arrange a viewing and/or test drive without any obligation. Please call beforehand to make an appointment, as we are not always on site. Van de Wert Trading B.V. Gksdpjz R Syusfx Ahdec Bedrijfsstraat 3 5391 LR Nuland

Condition: refurbished (used), Year of construction: 2024, machine/vehicle number: R-00719, load capacity: 10 kg, arm reach: 1,101 mm, controller manufacturer: R-30iB Mate Plus, teach pendant manufacturer: A05B-2255-C101#EGN, Refurbished FANUC LR-10iA/10 manufactured in 2024.03. The robot comes with an R-30iB Mate Plus controller including iPendant.   Our experts extensively tested the robot, after which we conducted a maintenance service according to the manufacturers’ specifications. The grease is examined for the amount of iron particles, indicating the corresponding axes' condition. Only robots in excellent mechanical condition will be completely refurbished, ensuring a long-term solution for our customers. This enables us to deliver our robots with a warranty term of 12 months as standard!   Brand: FANUC Model: LR-10iA/10 Model Number: A05B-1144-B201 Year of Manufacture Robot: 2024.03 Warranty term (months): 12   Payload (kg): 10 Reach (mm): 1101 Repeatability (mm): ± 0.01 Controlled Axes: 6-axis Installation Type: Floor, Upside-down, Angle Mount Weight (kg): 46   Controller: R-30iB Mate Plus Gedpfez R Synex Ahdjkc Year of Manufacture Cabinet: 2024.03 RCC Length (m): 7   Teach Pendant: A05B-2255-C101#EGN Teach Pendant Cable Length (m): 12

Condition: ready for operation (used), Year of construction: 2023, operating hours: 402 h, total height: 1,065 mm, total width: 645 mm, overall weight: 120 kg, travel distance X-axis: 165 mm, product length (max.): 685 mm, number of axes: 3, Plastic 3D printer manufactured in 2023. This FORMLABS Fuse 1 + 30W features Selective Laser Sintering (SLS) technology with a build volume of 165 × 165 × 300 mm. It is equipped with a 30 W Ytterbium Fiber Laser and a 10.1" interactive touchscreen for user-friendly operation. If you are looking to get high-quality 3D printing capabilities, consider the FORMLABS Fuse 1 + 30W machine we have for sale. Contact us for further details. 4 x Fuse 1+ units available • Technology: Selective Laser Sintering (SLS) • Build Volume (W × D × H): 165 × 165 × 300 mm • Layer Thickness: 110 µm • Build Speed (20% Packing Density): 0.5 L/h • Laser Type: Ytterbium Fiber Laser • Laser Power: 30 W • Laser Wavelength: 1070 nm • Laser Spot Size (FWHM): 247 µm • Beam Divergence: 3.24 mrad • Galvanometer: Formlabs Custom 3rd Generation • Hopper Capacity: 14.5 L • Connectivity: Wi-Fi (2.4 GHz + 5 GHz) • Connectivity: Gigabit Ethernet (1000 Mbit) • USB Interface: USB 2.0 • Display: 10.1" Interactive Touchscreen • Display Resolution: 1280 × 800 • Power Supply (EU): 230 VAC, 7.5 A, Single Phase • Power Frequency: 50/60 Hz Gedsz R Syhspfx Ahdokc • Material Refresh Rate: 30–50% • Supports Required: No • Laser Safety Class: Class 1 Laser ProductThey all have roughly the same number of operating hoursThey all come with a stand and are equipped with a printer cartridge Optional, not included: • 2 x Fuse Sift Station (Compatible Post-Processing Unit: Fuse Sift) available • Optional Feature: Nitrogen (Inert Gas) Printing • chambers

Condition: used, functionality: fully functional, mileage: 91,189 km, number of beds: 2, number of seats: 4, fuel type: diesel, gearing type: automatic, color: white, first registration: 01/2022, chassis manufacturer: Mercedes Benz, chassis model: Marco Polo 240d 2.0, total length: 5,140 mm, total width: 1,920 mm, total height: 1,980 mm, axle configuration: 2 axles, emission class: euro6, fuel tank capacity: 70 l, overall weight: 3,100 kg, empty load weight: 2,380 kg, steering wheel position: left, number of previous owners: 1, Year of construction: 2022, machine/vehicle number: W1V44781313961052, Equipment: ABS, air conditioning, airbag, all-season tires, car registration, central locking, electronic stability program (ESP), fog lights, full service history, onboard kitchen, power assisted steering, second-hand vehicle warranty, single beds, soot filter, twin bed, AVAILABLE NOW | Registration: MTK IC 16 | Mileage: 91,189 km | Location: Catania | Our Mercedes Marco Polo campervan is the perfect choice for those seeking a premium, stylish, and comfortable travel experience. Whether you're planning a city getaway or a long adventure, this van offers the ideal combination of performance, comfort, and reliability. Why buy the Mercedes Marco Polo? ✔ Spacious – With a length of 5.1 m, a width of 1.9 m, and a height of 2 m, the Marco Polo is easy to drive and park. ✔ Powerful and fuel-efficient – Features a 2.0 diesel engine (240d), 190 hp, automatic transmission, and Euro 6 emissions class. ✔ Ideal for up to 4 people – Equipped with 4 seats and 4 berths: 1 convertible double bed in the cabin and 1 double bed in the pop-up roof. ✔ Well-equipped for every trip – Includes a kitchenette, a convertible dining table, and a removable outdoor shower. ✔ Safe and reliable – Includes ABS, ESP, central locking, parking sensors, and tire pressure monitoring. Why buy from Indie Campers? 💰 Satisfaction guarantee – Try the van for 14 days, and if you're not satisfied, we'll refund you. 🚐 Try before you buy – Rent a vehicle first to make sure it's the right one for you. 🔒 1-year warranty – Warranty coverage is provided according to the terms and conditions of CarGarantie for purchases by private customers, based on location. Full terms are available upon request. 💵 Flexible financing – We offer flexible payment plans to suit your needs, depending on the location. 📝 Flexible viewings – We can arrange an appointment to view the vehicle at a time and date that is convenient for you, either in person or via video call. 🌍 Relocation – Is the vehicle not located in the right area? We offer relocation throughout Europe. Gkjdpfx Ahez R Sybedoc ✔ Up-to-date inspection and ready to go. Start your next adventure today! The Marco Polo campervan is in high demand. Don't miss this opportunity: contact us to arrange a viewing and make it yours today.

Condition: new, empty load weight: 4,100 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 4,880 mm, loading space width: 2,420 mm, loading space height: 980 mm, loading space volume: 12 m³, suspension: air, tire size: 385/65 R22,5, wheelbase: 131 mm, Equipment: ABS, Frame Central axle steel frame welded construction in lightweight design, optimized for weight, with tipping outriggers and rear tipping shaft; Hitching Tow bar, bent, with height-adjustable heavy-duty screw hitch eye 50 mm Supporting system 1 piece of mechanical support jack with crank on the left side in the direction of travel, 1 piece of step bracket screwed on Axles SAF Intradrum axles with drum brakes, S-cam brake 420/180 mm, Load capacity 9 t/axle, reinforced axle housings, off-road design, automatic brake linkage adjuster Wheels 4 steel rims 11.75 x 22.5, silver Braking system/suspension Two-line compressed air braking system Braking system manufacturer according to factory choice EBS system 2S2M, 2nd axle sensed RSS/RSP stability program Spring brake parking brake on 2nd axle Aluminum air reservoir Brake/air connection lines with Duomatic quick coupling EBS/ABS connection cable Hose lines laid under the drawbar Electronic air suspension with automatic lowering device via inductive switch and additional lowering lock via rotary switch on the trailer Without lifting and lowering device Tipper body Steel welded construction Fixed steel front wall 4 mm, approx. 980 mm high 2 step brackets inside and 1 on the outside of the front wall Fine-grained special steel floor sheet 5 mm 5 pairs of high-swiveling lashing rings 5 t 1-piece reinforced aluminum hollow profile side walls 60/40 mm, approx. 980 mm high, foldable with extended pivot pin locks and spring-assisted lifting mechanism, as well as additionally pivoting Side walls left and right with manual central locking 2 rear corner posts at sideboard height, mounted permanently on the side Steel rear wall 4 mm (HB400), approx. 980 mm high, pivoting with recessed mounting, hooks for metering chains on the rear wall and underside of the body Rear wall lock = automatic pneumatic lock With sealing strips Tarpaulin Plastic roll tarpaulin incl. aluminum tube and hand crank, without customs lock, in the direction of travel on the right horizontal tarpaulin bar rope fastening, tarpaulin overhang approx. 200 mm, front and rear zigzag fastening, tarpaulin overhang approx. 400 mm, stop bracket and locking device for rolled-up roll tarpaulin in the direction of travel on the right, Bracket for hand crank Tarpaulin fastening in the direction of travel on the left with 2 tension straps with rubber pads and tension latches on the underside of the body Tarpaulin color similar to RAL 9006 white aluminum Lighting/electrical system 24-volt lighting system according to ECE regulation R48 2 full-LED multi-chamber taillights "Aspöck" 2 LED position lights at the front 2 LED outline lights at the rear Flashing LED side marker lights, controlled via the turn signal 1 fixed electrical connection cable with 15-pin plug Painting Steel granulate cleaning, multi-layer epoxy zinc phosphate primer and spray painting with 2-component polyurethane topcoat Chassis = RAL 7021 black gray Tipper body incl. front wall = RAL 7021 black gray Side walls = RAL 7001 silver gray Rear corner posts = RAL 7021 black gray Rear wall = RAL 7021 black gray Wheel hubs black = powder-coated Support feet black = powder-coated Lateral underrun protection = factory choice Plastic parts black, unpainted Accessories/General 2 pairs of plastic single-wheel mudguards, with splash protection Fixed aluminum trapezoidal underrun guard, unpainted 2 wheel chocks, with bracket Noise damper = rubber pads Godpfez R Sx Rox Ahdekc Errors and omissions excepted.

Condition: good (used), axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, first registration: 01/2017, total length: 13,710 mm, total width: 2,470 mm, total height: 1,630 mm, suspension: air, tire size: 385/55-R22.5, color: black, Year of construction: 2017, Equipment: ABS, = Additional Options and Accessories = - ADR - EBS - Lift axle - Air suspension - Disc brakes Gksdpfx Asz R Sxwohdoc = Notes = 2017 D-TEC FlexiTrailer Traction with ABS/EBS, SAF axles with disc brakes, lift axle on the 1st axle, adjustable twistlock front arm for optimal axle load and traction with heavy 20-foot tank containers, extendable in the middle and at the rear, suitable for all containers, ADR (EX/II, EX/III, FL, AT), unladen weight: 4,881 kg, permissible total weight: 43,000 kg, tires 385/55-R22.5 (tread depth left: 5/9/5 mm; tread depth right: 7/9/3 mm), German registration. = Additional Information = Axle configuration Tire size: 385/55-R22.5 Axle brand: SAF DISC Brakes: Disc brakes Suspension: Air suspension Rear axle 1: Lift axle; Max. axle load: 9000 kg; Tire tread depth left: 30%; Tire tread depth right: 45% Rear axle 2: Max. axle load: 9000 kg; Tire tread depth left: 55%; Tire tread depth right: 55% Rear axle 3: Max. axle load: 9000 kg; Tire tread depth left: 30%; Tire tread depth right: 20% Weights Unladen weight: 4,881 kg Payload: 38,119 kg GVWR: 43,000 kg Functional Body brand: D-TEC FLEXITRAILER TRACTION Condition Technical condition: good Optical condition: good Identification License plate: OHAJX772 Additional information Please contact Arne Honingh for further information.

Condition: used, functionality: fully functional, mileage: 95,289 km, number of beds: 2, number of seats: 4, fuel type: diesel, gearing type: automatic, color: white, first registration: 01/2022, chassis manufacturer: Mercedes Benz, chassis model: Marco Polo 240d 2.0, total length: 5,140 mm, total width: 1,920 mm, total height: 1,980 mm, axle configuration: 2 axles, emission class: euro6, fuel tank capacity: 70 l, overall weight: 3,100 kg, empty load weight: 2,380 kg, steering wheel position: left, number of previous owners: 1, Year of construction: 2022, machine/vehicle number: W1V44781313966953, Equipment: ABS, air conditioning, airbag, all-season tires, car registration, central locking, electronic stability program (ESP), fog lights, full service history, onboard kitchen, power assisted steering, second-hand vehicle warranty, single beds, soot filter, twin bed, AVAILABLE NOW | License Plate: 3239 LXX | Mileage: 95,289 km | Location: Venice | Our Mercedes Marco Polo campervan is the perfect choice for those seeking a premium, stylish, and comfortable travel experience. Whether you're planning a city getaway or a long adventure, this van offers the ideal combination of performance, comfort, and reliability. Why buy the Mercedes Marco Polo? ✔ Spacious – With a length of 5.1 m, a width of 1.9 m, and a height of 2 m, the Marco Polo is easy to drive and park. ✔ Powerful and fuel-efficient – Features a 2.0 diesel engine (240d), 190 hp, automatic transmission, and Euro 6 emission class. ✔ Ideal for up to 4 people – Equipped with 4 seats and 4 sleeping berths: 1 double bed that converts in the cabin and 1 double bed in the pop-top roof. ✔ Well-equipped for every journey – Includes a kitchenette, convertible dining table, and removable outdoor shower. ✔ Safe and reliable – Includes ABS, ESP, central locking, parking sensors, and tire pressure monitoring. Gedjz R Sxkjpfx Ahdekc Why buy from Indie Campers? 💰 Satisfaction or money-back guarantee – Try the van for 14 days, and if you're not satisfied, we'll refund you. 🚐 Try before you buy – Rent a vehicle first to make sure it's the right one for you. 🔒 1-year warranty – Warranty coverage is provided according to the terms and conditions of CarGarantie for purchases by private customers, based on location. Full terms are available upon request. 💵 Flexible financing – We offer flexible payment plans to suit your needs, depending on the location. 📝 Flexible viewings – We can schedule an appointment to view the vehicle at a date and time that is convenient for you, in person or via video call. 🌍 Relocation – Is the vehicle not located in the right place? We offer relocation services throughout Europe. ✔ Up-to-date inspection and ready to go. Start your next adventure today! The Marco Polo campervan is in high demand. Don't miss this opportunity: contact us to schedule a viewing and make it yours today.

Condition: used, Year of construction: 2016, Overview This Haloila Octopus Compact is an automatic rotary-ring stretch wrapper for palletised loads, built in 2016 by Oy M. Haloila Ab. It is sold together with its pallet roller conveyor and control cabinet. The machine is in very good condition and fully functional; it was last used to wrap pallets of various oil containers and has been out of production since July 2024. It is still installed and under power and can be inspected on site. The rotating ring carries the film carriage around the stationary pallet, so the load itself is never turned - a compact layout suited to lines where the pallet runs straight through the winder on the conveyor. Technical data - Manufacturer: Haloila Gkodpjz R Sxdofx Ahdsc - Model: Octopus Compact - Year of manufacture: 2016 - Machine type: automatic rotary-ring pallet stretch wrapper (pallet winder) - Power supply: 3 x 400 V, 50 Hz - Connected load: 4 kW - Rated current: 10 A - CE mark on the machine plate Equipment - Rotating ring with film carriage and film pre-stretch unit - Pallet roller conveyor through the winder, with chain transfer section - Photoelectric sensors for pallet and load height detection - Control cabinet and operator panel with touch display, signal tower - Restart push-buttons at the infeed, safety fencing around the wrapping zone Condition Used, very good condition and fully functional. Out of production since July 2024. Sold without warranty. Availability Available immediately. The machine is still installed: dismantling and loading are to be arranged by the buyer. The matching oil filling line from the same site can also be offered on request. Location: Germany.

Condition: good (used), Year of construction: 2008, functionality: fully functional, SINGLE-SIDED EDGE BANDING MACHINE FOR PROCESSING MELAMINE, PVC & SOLID WOOD EDGES using EVA or PUR adhesives Total machine length 5,905 mm Workpiece thickness min./max. 6 - 60 mm, depending on edge thickness Edge band thickness 0.4 - 8 mm, depending on configuration Workpiece width min. 60 mm Workpiece length min. 180 mm Feed rate 18 m/min. without copying, 8 m/min. with copying Router unit with 2 motors at 2.0 kW each, 12,000 RPM pneumatically controlled, operating in both forward and reverse directions Gedez R Sw Topfx Ahdskc Roller platen 820 mm Glue application 1906M cartridge for cartridge magazines for EVA and PUR adhesives, with glue nozzle application unit Pressure zone with one main pressure roller and 2 follower rollers manually adjustable Trimming unit 1918 with 2 motors at 0.22 kW each, 9,000 RPM swiveling 0 - 10 degrees Multi-function router unit 1942 MOT 2 2 router motors at 0.6 kW each, 18,000 RPM, motor-adjustable swiveling 0 - 15 degrees Radius scraping unit 1929 up to max. radius R3 Copy router unit 1832 with 1 motor, 0.22 kW, 9,000 RPM Surface scraping blade 1964 Controlled from above and below Buffing unit 1940 2 motors at 0.12 kW each, swiveling 0 - 5 degrees Control: POWER-PC for efficient setup and changeover Windows-like user interface Simple program selection All information in plain text Extendable support rail approx. 500 mm

Condition: used, Year of construction: 2012, functionality: fully functional, overall weight: 2,600 kg, type of input current: AC, input voltage: 400 V, 4 x Wagner Permanent Magnet Separators – various models A total of 4 used permanent magnet separators from the manufacturer Wagner Magnete are for sale. The magnetic separators were used in our recycling and processing plant and serve to automatically separate ferromagnetic components from different material flows. Due to the restructuring and upcoming reconstruction of our recycling plant, the four magnetic separators are being offered for sale. Technical data of the 4 magnetic separators: Magnet 1: - Manufacturer: Wagner Magnete - Type: 0452-115/130-250 G2 - Equipment number: 546235 - Weight: approx. 2,600 kg - Motor power: 3 kW Magnet 2: - Manufacturer: Wagner Magnete - Type: 0452-115/170-250 G2 - Equipment number: 546236 - Weight: approx. 3,340 kg - Motor power: 3 kW Gsdpfx Ahez R Sw Hjdjkc Magnet 3: - Manufacturer: Wagner Magnete - Type: 0452-95/130-250 G2 - Equipment number: 546237 - Weight: approx. 2,200 kg - Motor power: 2.2 kW Magnet 4: - Manufacturer: Wagner Magnete - Type: 0452-95/130-250 G2 - Equipment number: 546986 - Weight: approx. 2,200 kg - Motor power: 2.2 kW Further technical specifications (all 4 magnetic separators): - Belt speed: 1.5 m/s - Motor manufacturer: SEW - Operating voltage: 400 V - Current type: Three-phase (AC) - Frequency: 50 Hz - Protection class: IP55 Condition and sale: All four magnetic separators are in used condition and show corresponding signs of wear and tear due to operation. The magnetic separators can be purchased individually or as a complete package. An on-site inspection is possible after prior appointment. Technical documentation is available. Price upon request. If you are interested or have any further questions, please do not hesitate to contact us.

Year of construction: 2021, operating hours: 7,632 h, condition: ready for operation (used), travel distance X-axis: 2,500 mm, controller manufacturer: HEIDENHAIN, controller model: TNC 640, spindle speed (max.): 4,000 rpm, number of axes: 3, This 3-axis KIHEUNG Volmatec KNC U1050 was manufactured in 2021. It features a Heidenhain TNC 640 control unit and has a spindle operating time of 5,624 hours. The machine comes with two milling heads and various spare parts, ensuring versatility in operations. If you are looking to get high-quality milling capabilities, consider the KIHEUNG Volmatec KNC U1050 bed type milling machine we have for sale. Contact us for further details. Gjdpfxez R Swge Ahdekc - Control Unit: Heidenhain TNC 640- Spindle Speed: Max. 4,000 rpm (2-gear step range: 0–1,000 / 1,001–4,000 rpm)- Spindle Power: 28 / 38 kW- X-Axis Travel: 2,500 mm- Y-Axis Travel: 1,050 mm- Z-Axis Travel: 1,600 mm- Number of Axes: 3-Axis- Spindle Operating Hours: 5,624 h- Program Runtime: 7,632 h- Included Accessories / Additional Equipment: 2x milling heads (1x installed, 1x new crate-packed), various spare parts, chip conveyor, external coolant filtration unit Technical Specification Taper Size SK 50

Condition: ready for operation (used), Year of construction: 2024, laser power: 6,000 W, This HGTECH TP 6535 PLUS was manufactured in 2024. It is a fiber CNC cutting laser designed for cutting pipes, tubes, and both closed and open profiles. It operates with power ranging from 1 to 6 kW and can handle pipes up to 8.5 meters long and 280 mm in diameter. Contact us for more information about this machine. • Capacity: Cuts pipes up to 8.5 m in length and up to 280 mm in diameter Gkodpjz R Swasfx Ahdjc

Condition: used, mileage: 963,918 km, power: 136 kW (184.91 HP), first registration: 05/2006, fuel type: diesel, tire size: 235/75/17.5, fuel: diesel, color: other, gearing type: mechanical, emission class: euro3, suspension: steel, Year of construction: 2006, Equipment: ABS, air conditioning, electric window regulation, fog lights, = Additional options and accessories = Gksdpfx Aez R Sv Njhdoc - Speed limiter - Rear doors - Radio/CD player - Side doors - Stability control - Digital tachograph = Further information = Tire size: 235/75/17.5 Brakes: Disc brakes Suspension: Leaf spring suspension Damage: None License plate: VIF934

Condition: used, mileage: 1,002,142 km, power: 136 kW (184.91 HP), first registration: 10/2008, fuel type: diesel, tire size: 245/70/17.5, fuel: diesel, color: other, gearing type: automatic, emission class: euro4, suspension: steel-air, Year of construction: 2008, Equipment: ABS, air conditioning, cruise control, electric window regulation, fog lights, = Additional Options and Accessories = - Rear doors - Radio/CD player - Side doors - Stability control - Digital tachograph = Additional Information = Tire size: 245/70/17.5 Brakes: Disc brakes Front axle: Suspension: Leaf spring suspension Gkedpfx Aoz R Sv Aohdec Rear axle: Suspension: Air suspension Unladen weight: 3,440 kg Damage: None License plate: 544AEE

Condition: used, mileage: 806,290 km, power: 315 kW (428.28 HP), first registration: 01/2016, fuel type: diesel, tire size: 315/70/22.5, wheelbase: 6,600 mm, fuel: diesel, color: white, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, suspension: steel-air, Year of construction: 2016, Equipment: ABS, air conditioning, central locking, cruise control, electric window regulation, fog lights, parking heater, second fuel tank, = Additional Options and Accessories = - (Roof) spoiler - Aluminum fuel tank - Climate control - Speed limiter - Refrigerator - Air suspension - Radio/CD player - Electrically adjustable side mirrors Gedpfxjz R Svvo Ahdekc - Sun visor - Stability control - Digital tachograph = Further Information = Brakes: Disc brakes Front axle: Tire size: 315/70/22.5; Suspension: leaf spring Rear axle 1: Tire size: 315/70/22.5; Suspension: air suspension Rear axle 2: Tire size: 385/55/22.5; Steered; Suspension: air suspension Unladen weight: 10,804 kg Payload: 16,196 kg Gross Vehicle Weight: 27,000 kg Damages: none Registration number: 28-BGT-6

Condition: used, mileage: 361,712 km, power: 162 kW (220.26 HP), first registration: 04/2015, fuel type: diesel, tire size: 285/70/19.5, fuel: diesel, color: white, gearing type: automatic, emission class: euro6, suspension: steel-air, total length: 5,350 mm, total width: 2,240 mm, total height: 2,200 mm, Year of construction: 2015, Equipment: ABS, electric window regulation, fog lights, = Additional options and equipment = - Aluminum fuel tank - Speed limiter - Rear doors - Air suspension - Radio/CD player - Side doors - Sun visor - Stability control Gksdjz R Svpepfx Ahdec - Digital tachograph = Further information = Tyre size: 285/70/19.5 Brakes: Disc brakes Front axle: Suspension: Leaf suspension Rear axle: Suspension: Air suspension Unladen weight: 6,730 kg Damages: none Registration number: 1LJZ542

Condition: used, mileage: 412,956 km, power: 162 kW (220.26 HP), first registration: 04/2015, fuel type: diesel, tire size: 285/70/19.5, fuel: diesel, color: white, gearing type: automatic, emission class: euro6, suspension: steel-air, total length: 5,350 mm, total width: 2,240 mm, total height: 2,200 mm, Year of construction: 2015, Equipment: ABS, electric window regulation, fog lights, = Additional options and accessories = - Aluminum fuel tank - Speed limiter - Rear doors - Air suspension - Radio/CD player - Side doors - Sun visor - Stability control - Digital speedometer = Additional information = Tire size: 285/70/19.5 Brakes: Disc brakes Front axle: Suspension: Leaf spring suspension Godpfxez R Svij Ahdjkc Rear axle: Suspension: Air suspension Unladen weight: 6,730 kg Damage: None License plate: 1LLE690

Condition: used, mileage: 321,049 km, power: 162 kW (220.26 HP), first registration: 09/2014, fuel type: diesel, tire size: 285/70/19.5, fuel: diesel, color: other, gearing type: automatic, emission class: euro6, suspension: steel-air, total length: 5,350 mm, total width: 2,240 mm, total height: 2,200 mm, Year of construction: 2014, Equipment: ABS, electric window regulation, fog lights, = Additional options and accessories = - Aluminum fuel tank - Speed limiter - Rear doors - Air suspension - Radio/CD player - Side doors - Sun visor - Stability control - Digital tachograph = Further information = Tire size: 285/70/19.5 Brakes: Disc brakes Front axle: Suspension: Leaf spring suspension Rear axle: Suspension: Air suspension Gkodpfxez R Svcj Ahdjc Unladen weight: 6,620 kg Damage: None License plate: 1JEX565

Condition: used, Year of construction: 2008, functionality: fully functional, Travel ranges: X 3,500 mm Gksdpfxez R Su Es Ahdec Y 1,250 mm Z 1,000 mm Control system: Heidenhain iTNC 530 Milling head: Automatically pivoting diagonal milling head with 2.5° x 2.5° indexing Spindle speed 3,000 rpm, tool holder SK50 Internal coolant supply 3 chip conveyors (2 longitudinal, 1 transverse) Four-sided splash guard enclosure in an enhanced special design