Elastomer test stand BIA Turnkey Test Syst

EXW Fixed price plus VAT

€100,000

Condition

Used

Location

Schweinfurt Germany

Elastomer test stand BIA Turnkey Test Syst

Machine data

Machine type:: Elastomer test stand BIA Turnkey Test Syst

Condition:: used

Price & Location

EXW Fixed price plus VAT

€100,000

Location:: Parisstr. 2, 97424 Schweinfurt, Deutschland

Call

Details about the offer

Listing ID:: A190-74406

Update:: 29.06.2026

Description

Elastomer Test Rig BIA Turnkey Test Systems Hexapod
Item No.: PT-065
Name: Elastomer Test Rig
Manufacturer: BIA Turnkey Test Systems

Description:
Test rig for determining and analyzing
bearing characteristic curves and values at vehicle operating points
bearing characteristic curves and values at operating points under specified temperatures
bearing behavior under operating load (settlement behavior, characteristic curve changes)
functional noise at operating points
on elastomer bearings in the chassis/drive system

Test specimens are mounted between an upper fixed platen and a lower mobile platen.
The mobile platen is driven by a hydraulic hexapod.
The fixed platform is attached to the test structure via a 6-axis force sensor. A linear actuator
allows adjustment of the distance between the two plates,
to accommodate a wide variety of test specimens and fixtures.
Degrees of freedom Amplitude Velocity Frequency Dynamics
Xs ±25 mm 1.5 m/s 85 Hz 25 kN
Ys ±25 mm 1.3 m/s 85 Hz 25 kN
Zs ±25 mm 0.8 m/s 85 Hz 50 kN
Mxs ±15° 340° / s 50 Hz 3.75 kNm
Bdjdpewhdnhofx Adqsf
Mys ±10° 360° / s 50 Hz 3.75 kNm
Mzs ±25° 580° / s 50 Hz 3 kNm
Hydraulic hexapod:
The hydraulic hexapod consists of six hydrostatically mounted hydraulic cylinders.
These have a cross-section of 12.53 cm².
Each cylinder has two parallel servo valves (38 l/min).
The six cylinders drive the mobile plate via six connecting rods.
The connecting rods have a hydraulic ball joint at their base. The oil pressure for this
hydrostatic bearing comes directly from the cylinder.

Linear actuator:
The distance between the upper and lower plates
can be adjusted using a linear actuator. The actuator consists of an electric motor,
a gearbox, and a screw-nut system. The linear actuator is equipped with an absolute encoder.
This is attached to the input shaft of the gearbox.

Hydraulic actuator:
The hydraulic cylinders are equipped with magnetostrictive position sensors.
Resolution: 0.0015%
Linearity:

The listing was translated automatically. Translation errors are possible.

Seller

Registered since: 2023

8 listings online

Call

Send inquiry

Telephone & Fax

+49 9721 ... show

These listings may also fit your interest.

Auction

Област София

9,223 km

Machining center
RapidMFC EVOLUTION II

€8,400

To the auction

Condition: ready for operation (used), Year of construction: 2009, machine/vehicle number: 19500648, functionality: fully functional, workpiece length (max.): 3,500 mm, workpiece width (max.): 130 mm, workpiece height (max.): 120 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Max. profile length: 3,500 mm Max. profile width: 130 mm Max. profile height: 120 mm MACHINE DETAILS Number of milling and drilling units: 7 Max. Friedrichs motor speed: 18,000 rpm Max. machine motor speed: 1,500 rpm Bdjdpfx Adezln D Eoqsf Electrical operating voltage: 400 V, 50 Hz Required network voltage: 20 kW Cable connections: 400 V NPE Operating height of the control cabinet: 1,050 mm Pneumatic operating pressure: 6 - 7 bar Pressure consumption per cycle: Approx. 3,500 NI Pneumatic line pressure at 70 °C: Approx. 15 bar EQUIPMENT Automatic screw feeder Arrangement of the units: On a wheel, which enables machining at different angles.

See details

Auction

Cutting and processing center Rapid Optima VI

Област София

9,223 km

Cutting and processing center
RapidOptima VI

€11,200

To the auction

Condition: ready for operation (used), Year of construction: 2006, machine/vehicle number: 19500624, functionality: fully functional, operating pressure: 7 bar, rotational speed (max.): 18,000 rpm, working height: 1,000 mm, No minimum price – guaranteed sale to the highest bidder! The new price of the machine was €950,000! TECHNICAL DETAILS Milling units / Motor power Motor power, small milling cutter: 0.27 kW Frequency, small milling cutter: 300 Hz Speed, small milling cutter: 18,000 rpm Motor power, large milling cutter: 1.1 kW Frequency, large milling cutter: 200 Hz Speed, large milling cutter: 12,000 rpm Tool data / Milling cutter data Collet diameter, small milling cutter: max. 8 mm Milling cutter diameter, small milling cutter: max. 8 mm Collet diameter, large milling cutter: max. 10 mm Milling cutter diameter, large milling cutter: max. 14 mm Electrical data Operating voltage: AC 400 V 3 N/PE Frequency: 50 Hz Rated current: 35 A Control voltage: 24 V Bdjdpfszlnxiox Adqsf Pneumatic data Working pressure: 0.7 / 1 MPa (7 / 10 bar) Compressed air consumption: 170 l/min Load limit of pneumatic lines at 70 °C: approx. 15 bar Working height Working height: 1,000 mm EQUIPMENT Clamping units Vertical clamping Maintenance unit with filter pressure regulator Control cabinet / Saw with lockable main switch Cutting unit: Allows cutting angles of 45 degrees and 90 degrees Machining units: Includes machining units and profile bearings Tools: Two screwdrivers, three cut-off wheels

See details

Auction

Cutting and processing center Elumatec SBZ 608

Област София

9,223 km

Cutting and processing center
ElumatecSBZ 608

€10,000

To the auction

Year of construction: 2005, condition: ready for operation (used), functionality: fully functional, power: 14 kW (19.03 HP), input current: 80 A, workpiece length (max.): 4,000 mm, machine/vehicle number: 6080008129, TECHNICAL DETAILS Maximum profile width: 130 mm Maximum profile height: 205 mm Maximum workpiece/profile length: 4,000 mm Processing capacity: 80 units MACHINE DETAILS Connection: 3 N/PE 400 V Frequency: 50 Hz Current: 80 A Power: 14 kW EQUIPMENT Powered, continuously adjustable gripper Lifting function for smooth feeding Profile guidance on rollers Bdedpfx Aozlnvuodqef Internal gripper to prevent damage to the profiles Integrated measuring sensors for workpiece length control Workpiece removal via outfeed table Portal design for high profile cross-sections Industrial PC with Windows operating system Barcode scanner

See details

Auction

Front loader forklift Jungheinrich TFG S80GE 360ZT

Schleswig-Holstein

7,667 km

Front loader forklift
JungheinrichTFG S80GE 360ZT

€15,500

To the auction

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2015, operating hours: 4,125 h, load capacity: 8,000 kg, lifting height: 3,600 mm, mast type: duplex, fork length: 2,050 mm, overall weight: 13,948 kg, An oil change was performed before the sale. Only the hydraulic oil was not changed. The filters have been replaced. TECHNICAL DETAILS Load capacity: 8,000 kg with load center at 900 mm Residual load capacity with Kaup 10T160 fork positioner: 7,320 kg with load center at 900 mm Tractive force with/without load: 45.6 kN Lifting height: approx. 3,600 mm Fork length: approx. 2,050 mm MACHINE DETAILS Engine: LPG GM 5.7L V8 Cylinders: 8 Displacement: 5,700 cm³ Rated speed: 2,200 rpm Bsdpfx Adezlhnqjqsdf Power: 85 kW Operating hours according to display: approx. 4,125 h Operation: Solo-Pilot with multi-function display Dimensions & Weight Overall length including forks: approx. 5,950 mm Overall width: approx. 2,150 mm Height with mast retracted: approx. 3,160 mm Height with mast extended: approx. 4,960 mm Height above protective roof: approx. 2,705 mm Self-weight: approx. 13,948 kg EQUIPMENT Kaup 10T160 fork positioner Duplex mast 3rd + 4th control circuit Side shifter Solo-Pilot Single pedal control Work lights front and rear Full cabin with heater Note: The two tires on the steering axle, as well as the fork tines, should be replaced. This can be requested and carried out by the seller. Fork tine length would be selectable.

See details

Auction

Laser cutting machine TRUMPF TruLaser 5030 classic

Dravograd

8,449 km

Laser cutting machine
TRUMPFTruLaser 5030 classic

€4,500

To the auction

Condition: used, Year of construction: 2007, operating hours: 39,023 h, machine/vehicle number: 1315318, laser power: 5,000 W, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 115 mm, workpiece weight (max.): 900 kg, No minimum price – guaranteed sale to the highest bidder! The machine has not been powered on for approximately one year. Bdjdjzlhcnepfx Adqjf TECHNICAL DETAILS Laser power: 5,000 W Working area (X x Y x Z): 3,000 mm x 1,500 mm x 115 mm Sheet metal thickness, structural steel max.: 25 mm Sheet metal thickness, stainless steel max.: 20 mm Sheet metal thickness, aluminum max.: 12 mm Maximum workpiece weight: 900 kg Positioning speed max.: 300 m/min Positioning accuracy: +/- 0.1 mm MACHINE DETAILS Control system: CNC Siemens Sinumerik 840 D Operating hours, laser on: 77,107 h Operating hours, beam on: 39,023 h Dimensions & Weight Machine dimensions (L x W x H): 11,100 mm x 4,600 mm x 2,400 mm Machine weight: 12,000 kg EQUIPMENT Automatic pallet changer NitroLine FocusLine PlasmaLine SprintLine ContourLine

See details

Auction

Groningen

7,504 km

4-axis CNC machine
ElumatecSBZ 140

€18,000

To the auction

Year of construction: 2010, condition: ready for operation (used), functionality: fully functional, working length: 7,600 mm, machine/vehicle number: 1400040505, number of axes: 4, TECHNICAL DETAILS Max. machining length with end face machining: 7,600 mm Max. machining length without end face machining: 7,720 mm EQUIPMENT 12 pneumatic collet chucks 2 work areas 4-axis profile machining center; stepless machining between -90° and +90° with each available tool Bdsdpfx Adszhuyfeqjf Automatic clamping position adjustment with absolute measuring system Two separate machining zones for tandem operation 4-axis control 18.5" color monitor, USB ports, and network connection Windows operating system EluCam software Automatic profile length measurement (on both sides) Barcode scanner The traversing tool magazine ensures short tool change times and thus optimal machining cycles; the magazine can be equipped with eight tools. 8x tool holders with collet chucks

See details

Auction

Universal machining center DECKEL MAHO DMU 80 monoBlock

Baden-Württemberg

7,992 km

Universal machining center
DECKEL MAHODMU 80 monoBlock

€15,500

To the auction

Condition: ready for operation (used), Year of construction: 2005, operating hours: 20,729 h, functionality: fully functional, travel distance X-axis: 980 mm, travel distance Y-axis: 630 mm, travel distance Z-axis: 630 mm, controller model: Heidenhain iTNC 530, rotational speed (max.): 18,000 rpm, TECHNICAL DETAILS Travel range X-axis: 980 mm Travel range Y-axis: 630 mm Travel range Z-axis: 630 mm Spindle speed range: 0–18,000 rpm Tool holder: HSK 63 MACHINE DETAILS Control system: Heidenhain iTNC 530 Bedpfjzmry Tox Adqjdf Clamping area: 1,250 × 700 mm Operating hours Machine operating hours: 46,922 h Program runtime: 20,279 h Spindle operating hours: 20,746 h EQUIPMENT Fixed angular table 3D measuring probe Heidenhain Tool measurement in the working area with BLUM laser Vertical tool changer with 32 magazine slots Full protective enclosure with sliding doors and interior lighting Electronic handwheel Operating modes 3 and 4 Chip conveyor Coolant system 3 height-adjustable machine feet Spindle cooler Control cabinet cooler from Rittal Operating manuals

See details

Auction

Vertical machining center BRIDGEPORT VMC 800

Baden-Württemberg

7,992 km

Vertical machining center
BRIDGEPORTVMC 800

€9,000

To the auction

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 500 mm, controller model: Heidenhain TNC 410, rotational speed (max.): 10,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range X-axis: 800 mm Travel range Y-axis: 500 mm Travel range Z-axis: 500 mm Spindle speed range: 0–10,000 rpm Spindle speed control: stepless Tool holder: SK 40 Magazine capacity: 20 MACHINE DETAILS Control system: Heidenhain TNC 410 Bdedpjzmryyjfx Adqsf Clamping area: 1,000 × 500 mm EQUIPMENT Fixed angular table Vertical tool changer Full enclosure with sliding doors and interior lighting Various tool holders SK 40 Electronic handwheel Coolant system with enhanced pump Coolant pressure: 20 bar Chip conveyor Operating manual

See details

Auction

Baden-Württemberg

7,992 km

Machining center
MIKRONVCP 800 W

€9,500

To the auction

Condition: ready for operation (used), Year of construction: 2002, operating hours: 20,377 h, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 500 mm, controller model: Heidenhain iTNC 530, rotational speed (max.): 20,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 800 mm Travel range, Y-axis: 650 mm Travel range, Z-axis: 500 mm Speed range: 0–20,000 rpm Speed control: stepless Magazine capacity: 30 Tool holder: HSK 63 MACHINE DETAILS Control system: Heidenhain iTNC 530 Clamping area: 900 × 600 mm Bjdpjzmrpuofx Adqedf Operating hours Machine operating hours: 54,796 h Spindle operating hours: 23,462 h Program run time: 20,377 h EQUIPMENT Fixed tilting table Vertical tool changer Full enclosure with sliding doors and interior lighting Electronic handwheel Tool measurement in the working area with BLUM laser 3D infrared probe Renishaw Chip conveyor Coolant system 4 height-adjustable machine feet Operating manuals

See details

Auction

Horizontal plate boring mill PARPAS ML 100 - 5000

Sachsen

8,028 km

Horizontal plate boring mill
PARPASML 100 - 5000

€7,000

To the auction

Condition: ready for operation (used), Year of construction: 1991, functionality: limited functionality, travel distance X-axis: 5,020 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 2,000 mm, spindle diameter: 100 mm, controller model: Heidenhain 415 B, TECHNICAL DETAILS Spindle diameter: 100 mm Travel in X-axis: 5,020 mm Travel in Y-axis: 1,000 mm Travel in Z-axis: 2,000 mm Tool holder: SK 50 MACHINE DETAILS Control system: Heidenhain 415 B Bedpfxjzlryqj Adqjdf Rotary table dimensions: 2,500 x 2,000 mm EQUIPMENT Indexable milling head 2.5 60-position tool changer Rotary table manufacturer: Scharmann Note: The rotary function of the rotary table is defective. The machine is sold without pallet changers.

See details

Advertise here